Table Of Contents
Configuring the Fabric Extender
Associating a Fabric Extender to a Fabric Interface
Associating a Fabric Extender to an Ethernet Interface
Associating a Fabric Extender to an EtherChannel
Disassociating a Fabric Extender from an Interface
Configuring the Fabric Extender
Displaying Fabric Extender Information
Displaying Configuration Information
Displaying Chassis Management Information
Configuring the Fabric Extender
This chapter describes how to configure a Cisco Nexus 2000 Series Fabric Extender with a Cisco Nexus 5000 Series switch and includes the following sections:
•
Associating a Fabric Extender to a Fabric Interface
•
•
•
Associating a Fabric Extender to a Fabric Interface
A Fabric Extender is connected to the switch through physical Ethernet interfaces or an EtherChannel. By default, the switch does not allow the attached Fabric Extender to connect until it has been assigned a chassis ID and is associated with the connected interface.
Note
Caution
This section includes the following topics:
•
•
•
Associating a Fabric Extender to an Ethernet Interface
To associate the Fabric Extender to an Ethernet interface, perform this task:
This example shows how to associate the Fabric Extender to an Ethernet interface on the switch:
switch# configure terminal switch(config)# interface ethernet 1/40 switch(config-if)# switchport mode fex-fabric switch(config-if)# fex associate 100This example shows how to display the association of the Fabric Extender and the switch:
switch# show interface ethernet 1/40 fex-intf Fabric FEX Interface Interfaces --------------------------------------------------- Eth1/40 Eth100/1/48 Eth100/1/47 Eth100/1/46 Eth100/1/45 Eth100/1/44 Eth100/1/43 Eth100/1/42 Eth100/1/41 Eth100/1/40 Eth100/1/39 Eth100/1/38 Eth100/1/37 Eth100/1/36 Eth100/1/35 Eth100/1/34 Eth100/1/33 Eth100/1/32 Eth100/1/31 Eth100/1/30 Eth100/1/29 Eth100/1/28 Eth100/1/27 Eth100/1/26 Eth100/1/25 Eth100/1/24 Eth100/1/23 Eth100/1/22 Eth100/1/21 Eth100/1/20 Eth100/1/19 Eth100/1/18 Eth100/1/17 Eth100/1/16 Eth100/1/15 Eth100/1/14 Eth100/1/13 Eth100/1/12 Eth100/1/11 Eth100/1/10 Eth100/1/9 Eth100/1/8 Eth100/1/7 Eth100/1/6 Eth100/1/5 Eth100/1/4 Eth100/1/3 Eth100/1/2 Eth100/1/1Associating a Fabric Extender to an EtherChannel
To associate the Fabric Extender to an EtherChannel, perform this task:
This example shows how to associate the Fabric Extender to an EtherChannel interface on the switch:
switch# configure terminal switch(config)# interface port-channel 4 switch(config-if)# switchport mode fex-fabric switch(config-if)# fex associate 100 switch(config-if)# exit switch(config)# interface ethernet 1/37 switch(config-if)# switchport mode fex-fabric switch(config-if)# fex associate 100 switch(config-if)# channel-group 4 switch(config-if)# exit switch(config)# interface ethernet 1/38 switch(config-if)# switchport mode fex-fabric switch(config-if)# fex associate 100 switch(config-if)# channel-group 4 switch(config-if)# exit switch(config)# interface ethernet 1/39 switch(config-if)# switchport mode fex-fabric switch(config-if)# fex associate 100 switch(config-if)# channel-group 4 switch(config-if)# exit switch(config)# interface ethernet 1/40 switch(config-if)# switchport mode fex-fabric switch(config-if)# fex associate 100 switch(config-if)# channel-group 4
Note
This example shows how to display the association of the Fabric Extender and the switch:
switch# show interface port-channel 4 fex-intf Fabric FEX Interface Interfaces --------------------------------------------------- Po4 Eth100/1/48 Eth100/1/47 Eth100/1/46 Eth100/1/45 Eth100/1/44 Eth100/1/43 Eth100/1/42 Eth100/1/41 Eth100/1/40 Eth100/1/39 Eth100/1/38 Eth100/1/37 Eth100/1/36 Eth100/1/35 Eth100/1/34 Eth100/1/33 Eth100/1/32 Eth100/1/31 Eth100/1/30 Eth100/1/29 Eth100/1/28 Eth100/1/27 Eth100/1/26 Eth100/1/25 Eth100/1/24 Eth100/1/23 Eth100/1/22 Eth100/1/21 Eth100/1/20 Eth100/1/19 Eth100/1/18 Eth100/1/17 Eth100/1/16 Eth100/1/15 Eth100/1/14 Eth100/1/13 Eth100/1/12 Eth100/1/11 Eth100/1/10 Eth100/1/9 Eth100/1/8 Eth100/1/7 Eth100/1/6 Eth100/1/5 Eth100/1/4 Eth100/1/3 Eth100/1/2 Eth100/1/1Disassociating a Fabric Extender from an Interface
To disassociate the Fabric Extender from an interface, perform this task:
switch(config-if)# no fex associate
Disassociates the Fabric Extender unit attached to the interface.
Configuring the Fabric Extender
To configure global features for a Fabric Extender, perform this tasks:
Caution
Redistributing the Links
When you provision the Fabric Extender with statically pinned interfaces (see the "Static Pinning Fabric Interface Connection" section on page 1-5), the downlink host interfaces on the Fabric Extender are pinned to the fabric interfaces in the order they were initially configured. If you want to maintain a specific relationship of host interfaces to fabric interface across reboots, you should re-pin the links.
You may want to perform this function in these two situations:
•
•
Changing the Number of Links
If you initially configured port 33 on the parent switch as your only fabric interface, all 48 host interfaces are pinned to this port. If you provision another port, for example 35, then you must enter the pinning max-links 2 command to redistribute the host interfaces. All host interfaces are brought down and host interfaces 1 to 24 are pinned to fabric interface 33 and host interfaces 25 to 48 are pinned to fabric interface 35.
Maintaining the Pinning Order
The pinning order of the host interfaces is initially determined by the order in which the fabric interfaces were configured. In this example, four fabric interfaces were configured in the following order:
switch# show interface ethernet 1/35 fex-intf Fabric FEX Interface Interfaces --------------------------------------------------- Eth1/35 Eth100/1/12 Eth100/1/11 Eth100/1/10 Eth100/1/9 Eth100/1/8 Eth100/1/7 Eth100/1/6 Eth100/1/5 Eth100/1/4 Eth100/1/3 Eth100/1/2 Eth100/1/1 switch# show interface ethernet 1/33 fex-intf Fabric FEX Interface Interfaces --------------------------------------------------- Eth1/33 Eth100/1/24 Eth100/1/23 Eth100/1/22 Eth100/1/21 Eth100/1/20 Eth100/1/19 Eth100/1/18 Eth100/1/17 Eth100/1/16 Eth100/1/15 Eth100/1/14 Eth100/1/13 switch# show interface ethernet 1/38 fex-intf Fabric FEX Interface Interfaces --------------------------------------------------- Eth1/38 Eth100/1/36 Eth100/1/35 Eth100/1/34 Eth100/1/33 Eth100/1/32 Eth100/1/31 Eth100/1/30 Eth100/1/29 Eth100/1/28 Eth100/1/27 Eth100/1/26 Eth100/1/25 switch# show interface ethernet 1/40 fex-intf Fabric FEX Interface Interfaces --------------------------------------------------- Eth1/40 Eth100/1/48 Eth100/1/47 Eth100/1/46 Eth100/1/45 Eth100/1/44 Eth100/1/43 Eth100/1/42 Eth100/1/41 Eth100/1/40 Eth100/1/39 Eth100/1/38 Eth100/1/37The next time that you reboot the Fabric Extender, the configured fabric interfaces are pinned to the host interfaces in an ascending order by port number of the fabric interface. If you want to configure the same fixed distribution of host interfaces without restarting the Fabric Extender, enter the fex pinning redistribute command (see the "Static Pinning Fabric Interface Connection" section on page 1-5).
To redistribute the host interfaces on the Fabric Extender, perform this task:
switch# fex pinning redistribute chassis
Redistributes the host connections. The range of the chassis ID is from 100 to 199.
This example shows how to redistribute the host interfaces on a Fabric Extender:
switch# fex pinning redistribute 100
Caution
Upgrading the Fabric Extender
To upgrade a Cisco Nexus 2000 Series Fabric Extender, perform these steps:
Step 1
Step 2
While the installation is in progress, the Fabric Extender remains online.
The new image is pushed to the Fabric Extender by the parent switch. Once the software image has successfully been installed, the parent switch reboots. The Fabric Extender is also rebooted automatically to maintain the software version compatibility between the parent switch and the Fabric Extender. When the parent switch comes up, it rediscovers the Fabric Extender and brings it online.
This process is the least disruptive process for the hosts and servers connected to the Fabric Extender.
Displaying Fabric Extender Information
This section describes the show commands that are available to display the configuration and status of the Fabric Extender and includes the following topics:
•
•
Displaying Configuration Information
To display configuration information about the defined interfaces, perform one of these tasks:
This example shows how to display all the attached Fabric Extender units:
switch# show fex FEX FEX FEX FEX Number Description State Model Serial ------------------------------------------------------------------------ 100 FEX0100 Online N5K-C5110T-BF-1GE FOX1242GJSQThis example shows how to display the detailed status of a specific Fabric Extender:
switch# show fex 100 detail FEX: 100 Description: FEX0100 state: Online FEX version: 4.0(1a)N2(0.101) [Switch version: 4.0(1a)N2(0.101)] Extender Model: N5K-C5110T-BF-1GE, Extender Serial: JAF1241BLFN Part No: 73-12009-02 Card Id: 70, Mac Addr: 00:0d:ec:b1:28:42, Num Macs: 64 Module Sw Gen: 17 [Switch Sw Gen: 17] pinning-mode: static Max-links: 1 Fabric port for control traffic: Eth1/40 Fabric interface state: Eth1/40 - Interface Up. State: Active Fex Port State Fabric Port Primary Fabric Eth100/1/1 Up Eth1/40 Eth1/40 Eth100/1/2 Down Eth1/40 Eth1/40 Eth100/1/3 Down Eth1/40 Eth1/40 Eth100/1/4 Down Eth1/40 Eth1/40 Eth100/1/5 Down Eth1/40 Eth1/40 Eth100/1/6 Down Eth1/40 Eth1/40 Eth100/1/7 Down Eth1/40 Eth1/40 Eth100/1/8 Down Eth1/40 Eth1/40 Eth100/1/9 Down Eth1/40 Eth1/40 Eth100/1/10 Down Eth1/40 Eth1/40 Eth100/1/11 Down Eth1/40 Eth1/40 Eth100/1/12 Down Eth1/40 Eth1/40 Eth100/1/13 Down Eth1/40 Eth1/40 Eth100/1/14 Down Eth1/40 Eth1/40 Eth100/1/15 Up Eth1/40 Eth1/40 Eth100/1/16 Down Eth1/40 Eth1/40 Eth100/1/17 Down Eth1/40 Eth1/40 Eth100/1/18 Down Eth1/40 Eth1/40 Eth100/1/19 Down Eth1/40 Eth1/40 Eth100/1/20 Down Eth1/40 Eth1/40 Eth100/1/22 Down Eth1/40 Eth1/40 Eth100/1/24 Down Eth1/40 Eth1/40 Eth100/1/25 Down Eth1/40 Eth1/40 Eth100/1/26 Down Eth1/40 Eth1/40 Eth100/1/27 Down Eth1/40 Eth1/40 Eth100/1/28 Down Eth1/40 Eth1/40 Eth100/1/29 Down Eth1/40 Eth1/40 Eth100/1/30 Down Eth1/40 Eth1/40 Eth100/1/31 Up Eth1/40 Eth1/40 Eth100/1/32 Down Eth1/40 Eth1/40 Eth100/1/33 Down Eth1/40 Eth1/40 Eth100/1/34 Down Eth1/40 Eth1/40 Eth100/1/35 Down Eth1/40 Eth1/40 Eth100/1/36 Down Eth1/40 Eth1/40 Eth100/1/37 Down Eth1/40 Eth1/40 Eth100/1/38 Down Eth1/40 Eth1/40 Eth100/1/39 Down Eth1/40 Eth1/40 Eth100/1/40 Down Eth1/40 Eth1/40 Eth100/1/41 Down Eth1/40 Eth1/40 Eth100/1/42 Down Eth1/40 Eth1/40 Eth100/1/43 Down Eth1/40 Eth1/40 Eth100/1/44 Down Eth1/40 Eth1/40 Eth100/1/45 Down Eth1/40 Eth1/40 Eth100/1/46 Down Eth1/40 Eth1/40 Eth100/1/47 Up Eth1/40 Eth1/40 Eth100/1/48 Down Eth1/40 Eth1/40 Logs: [12/10/2008 00:11:40.698999] Module timed out [12/10/2008 00:11:44.501221] Module register received [12/10/2008 00:11:44.502240] Registration response sent [12/10/2008 00:11:44.587581] Module Online Sequence [12/10/2008 00:11:49.140170] Module Online [12/10/2008 00:18:46.662135] Module disconnected [12/10/2008 00:18:46.663222] Offlining Module [12/10/2008 00:18:46.663856] Module Offline Sequence [12/10/2008 00:18:49.317584] Module Offline [12/10/2008 00:19:30.427864] Module register received [12/10/2008 00:19:30.428875] Registration response sent [12/10/2008 00:19:30.456882] Module Online Sequence [12/10/2008 00:19:32.62827] Module Online [12/10/2008 00:20:37.196648] Module disconnected [12/10/2008 00:20:37.197782] Offlining Module [12/10/2008 00:20:37.199299] Module Offline Sequence [12/10/2008 00:20:39.859971] Module Offline [12/10/2008 00:21:13.945372] Module register received [12/10/2008 00:21:13.946435] Registration response sent [12/10/2008 00:21:13.974962] Module Online Sequence [12/10/2008 00:21:15.737667] Module OnlineThis example shows how to display the Fabric Extender interfaces pinned to a specific switch interface:
switch# show interface ethernet 1/40 fex-intf Fabric FEX Interface Interfaces --------------------------------------------------- Eth1/40 Eth100/1/48 Eth100/1/47 Eth100/1/46 Eth100/1/45 Eth100/1/44 Eth100/1/43 Eth100/1/42 Eth100/1/41 Eth100/1/40 Eth100/1/39 Eth100/1/38 Eth100/1/37 Eth100/1/36 Eth100/1/35 Eth100/1/34 Eth100/1/33 Eth100/1/32 Eth100/1/31 Eth100/1/30 Eth100/1/29 Eth100/1/28 Eth100/1/27 Eth100/1/26 Eth100/1/25 Eth100/1/24 Eth100/1/22 Eth100/1/20 Eth100/1/19 Eth100/1/18 Eth100/1/17 Eth100/1/16 Eth100/1/15 Eth100/1/14 Eth100/1/13 Eth100/1/12 Eth100/1/11 Eth100/1/10 Eth100/1/9 Eth100/1/8 Eth100/1/7 Eth100/1/6 Eth100/1/5 Eth100/1/4 Eth100/1/3 Eth100/1/2 Eth100/1/1This example shows how to display the switch interfaces that are connected to a Fabric Extender uplink:
switch# show interface fex-fabric Fabric Fabric Fex FEX Fex Port Port State Uplink Model Serial --------------------------------------------------------------- --- Eth1/1 Discovered 1 N5K-C5110T-BF-1GE FOX1242GJSQ --- Eth1/2 Discovered 4 N5K-C5110T-BF-1GE FOX1242GJSQ --- Eth1/3 Discovered 2 N5K-C5110T-BF-1GE FOX1242GJSQ 100 Eth1/40 Active 3 N5K-C5110T-BF-1GE FOX1242GJSQ
Note
This example shows how to display the SFP+ transceiver and diagnostic optical monitoring (DOM) information for Fabric Extender uplinks:
switch# show interface ethernet 1/40 transceiver Ethernet1/40 sfp is present name is CISCO-EXCELIGHT part number is SPP5101SR-C1 revision is A serial number is ECL120901AV nominal bitrate is 10300 MBits/sec Link length supported for 50/125mm fiber is 82 m(s) Link length supported for 62.5/125mm fiber is 26 m(s) cisco id is -- cisco extended id number is 4switch# show interface ethernet 1/40 transceiver fex-fabric Ethernet1/40 sfp is present name is CISCO-EXCELIGHT part number is SPP5101SR-C1 revision is A serial number is ECL120601U0 nominal bitrate is 10300 MBits/sec Link length supported for 50/125mm fiber is 82 m(s) Link length supported for 62.5/125mm fiber is 26 m(s) cisco id is -- cisco extended id number is 4
Note
Displaying Chassis Management Information
To display configuration information used on the switch supervisor to manage the Fabric Extender, perform one of these tasks:
This example shows how to display the module information about all connected Fabric Extender units:
switch# show module fex FEX Mod Ports Card Type Model Status. --- --- ----- ---------------------------------- ------------------ ----------- 100 1 48 Fabric Extender 48x1GE Module N2K-C2148T-1GE ok FEX Mod Sw Hw World-Wide-Name(s) (WWN) --- --- -------------- ------ ----------------------------------------------- 100 1 4.0(1a)N2(1) 0.2 -- FEX Mod MAC-Address(es) Serial-Num --- --- -------------------------------------- ---------- 100 1 000d.ecb1.3f00 to 000d.ecb1.3f2fff JAF1244ATERThis example shows how to display the module information about a specific Fabric Extender unit:
switch# show module fex 100 FEX Mod Ports Card Type Model Status. --- --- ----- ---------------------------------- ------------------ ----------- 100 1 48 Fabric Extender 48x1GE Module N2K-C2148T-1GE ok FEX Mod Sw Hw World-Wide-Name(s) (WWN) --- --- -------------- ------ ----------------------------------------------- 100 1 4.0(1a)N2(1) 0.2 -- FEX Mod MAC-Address(es) Serial-Num --- --- -------------------------------------- ---------- 100 1 000d.ecb1.3f00 to 000d.ecb1.3f2fff JAF1244ATERThis example shows how to display the inventory information about a specific Fabric Extender unit:
switch# show inventory fex 100 NAME: "FEX 100 CHASSIS", DESCR: "N2K-C2148T-1GE CHASSIS" PID: N2K-C2148T-1GE , VID: V00 , SN: JAF1244ATER NAME: "FEX 100 Module 1", DESCR: "Fabric Extender Module: 48x1GE, 4X10GE Supervisor" PID: N2K-C2148T-1GE , VID: V00 , SN: FOX1242GJT4 NAME: "FEX 100 Fan 1", DESCR: "Fabric Extender Fan module" PID: N2K-C2148-FAN , VID: N/A , SN: N/A NAME: "FEX 100 Power Supply 1", DESCR: "Fabric Extender AC power supply" PID: N5K-PAC-200W , VID: 00V0, SN: PAC12473L2JThis example shows how to display diagnostic test results for a specific Fabric Extender unit:
switch# show diagnostic result fex 100 FEX-100: 48x1GE/Supervisor SerialNo : JAF1241BLFN Overall Diagnostic Result for FEX-100 : OK Test results: (. = Pass, F = Fail, U = Untested) TestPlatform: 0) SPROM: ---------------> . 1) MV88E6095: ---------------> . 2) Fan: ---------------> . 3) PowerSupply: ---------------> F 4) TempSensor: ---------------> . TestForwardingPorts: Eth 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Port ------------------------------------------------------------------------ . . . . . . . . . . . . . . . . . . . . . . . . Eth 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Port ------------------------------------------------------------------------ . . . . . . . . . . . . . . . . . . . . . . . . TestFabricPorts: Fabric 1 2 3 4 Port ------------ . . . .This example shows how to display the environment status for a specific Fabric Extender unit:
switch# show environment fex 100 Temperature Fex 100: ----------------------------------------------------------------- Module Sensor MajorThresh MinorThres CurTemp Status (Celsius) (Celsius) (Celsius) ----------------------------------------------------------------- 1 Outlet-1 60 50 29 ok 1 Inlet-1 50 40 21 ok Fan Fex: 100: ------------------------------------------------------ Fan Model Hw Status ------------------------------------------------------ Chassis N2K-C2148-FAN -- ok PS-1 N5K-PAC-200W -- failure PS-2 N5K-PAC-200W -- ok Power Supply Fex 100: --------------------------------------------------------------------------- Voltage: 12 Volts ----------------------------------------------------- PS Model Power Power Status (Watts) (Amp) ----------------------------------------------------- 1 -- -- -- fail/shutdown 2 N5K-PAC-200W 200.04 16.67 ok Mod Model Power Power Power Power Status Requested Requested Allocated Allocated (Watts) (Amp) (Watts) (Amp) --- ------------------- ------- ---------- --------- ---------- ---------- 1 N5K-C5110T-BF-1GE 96.00 8.00 96.00 8.00 powered-up Power Usage Summary: -------------------- Power Supply redundancy mode: redundant Total Power Capacity 200.04 W Power reserved for Supervisor(s) 96.00 W Power currently used by Modules 0.00 W ------------- Total Power Available 104.04 W -------------This example shows how to display the SPROM for a specific Fabric Extender unit:
switch# show sprom fex 100 all DISPLAY FEX 100 SUP sprom contents Common block: Block Signature : 0xabab Block Version : 3 Block Length : 160 Block Checksum : 0x1774 EEPROM Size : 4096 Block Count : 3 FRU Major Type : 0x6002 FRU Minor Type : 0x0 OEM String : Cisco Systems, Inc. Product Number : N2K-C2148T-1GE Serial Number : JAF1244ATER Part Number : 73-12009-02 Part Revision : 07 Mfg Deviation : 0 H/W Version : 0.2 Mfg Bits : 0 Engineer Use : 0 snmpOID : 9.12.3.1.9.72.8.0 Power Consump : -800 RMA Code : 0-0-0-0 CLEI Code : COMEB00ARA VID : V00 Supervisor Module specific block: Block Signature : 0x6002 Block Version : 2 Block Length : 103 Block Checksum : 0x592 Feature Bits : 0x0 HW Changes Bits : 0x2 Card Index : 11011 MAC Addresses : 00-00-00-00-00-00 Number of MACs : 0 Number of EPLD : 0 Port Type-Num : 1-48;2-4 Sensor #1 : 60,50 Sensor #2 : 60,50 Sensor #3 : 60,50 Sensor #4 : 60,50 Sensor #5 : 50,40 Sensor #6 : 50,40 Sensor #7 : 50,40 Sensor #8 : 50,40 Max Connector Power: 1000 Cooling Requirement: 300 Ambient Temperature: 40 DISPLAY FEX 100 backplane sprom contents: Common block: Block Signature : 0xabab Block Version : 3 Block Length : 160 Block Checksum : 0x173f EEPROM Size : 65535 Block Count : 5 FRU Major Type : 0x6001 FRU Minor Type : 0x0 OEM String : Cisco Systems, Inc. Product Number : N2K-C2148T-1GE Serial Number : FOX1242GJT4 Part Number : 68-3342-02 Part Revision : 05 Mfg Deviation : 0 H/W Version : 0.0 Mfg Bits : 0 Engineer Use : 0 snmpOID : 9.12.3.1.3.820.0.0 Power Consump : 0 RMA Code : 0-0-0-0 CLEI Code : COMEB00ARA VID : V00 Chassis specific block: Block Signature : 0x6001 Block Version : 3 Block Length : 39 Block Checksum : 0x2b6 Feature Bits : 0x0 HW Changes Bits : 0x2 Stackmib OID : 0 MAC Addresses : 00-0d-ec-b1-3f-00 Number of MACs : 64 OEM Enterprise : 0 OEM MIB Offset : 0 MAX Connector Power: 0 WWN software-module specific block: Block Signature : 0x6005 Block Version : 1 Block Length : 0 Block Checksum : 0x66 wwn usage bits: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 License software-module specific block: Block Signature : 0x6006 Block Version : 1 Block Length : 16 Block Checksum : 0x77 lic usage bits: 00 00 00 00 00 00 00 00 DISPLAY FEX 100 power-supply 1 sprom contents: Common block: Block Signature : 0xabab Block Version : 3 Block Length : 124 Block Checksum : 0x1610 EEPROM Size : 124 Block Count : 1 FRU Major Type : 0xab01 FRU Minor Type : 0x1 OEM String : Cisco Systems, Inc. Product Number : N5K-PAC-200W Serial Number : PAC12473L2J Part Number : 341-0335-01 Part Revision : 01 CLEI Code : COUPADSBAA VID : 00V0 snmpOID : 0.0.0.0.0.0.0.0 H/W Version : 0.1 Current : 1667 RMA Code : 0-0-0-0 DISPLAY FEX 100 power-supply 2 sprom contents: Common block: Block Signature : 0x0 Block Version : 0 Block Length : 0 Block Checksum : 0x0 EEPROM Size : 0 Block Count : 0 FRU Major Type : 0x0 FRU Minor Type : 0x0 OEM String : Product Number : Serial Number : Part Number : Part Revision : CLEI Code : VID : V00 snmpOID : 0.0.0.0.0.0.0.0 H/W Version : 0.0 Current : 0 RMA Code : 0-0-0-0
