Table Of Contents
Z Commands
zone copy
zone default-zone
zone merge
zone name
zoneset
Z Commands
The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric switches. All commands are shown here in alphabetical order regardless of command mode. Please see the Command Mode section to determine the appropriate mode for each command. For more information, see the Cisco MDS 9000 Family Configuration Guide.
•zone copy
•zone default-zone
•zone merge
•zone name
•zoneset
zone copy
To copy the active zoneset to the full zoneset, use the zone copy command.
zone copy active -zoneset full-zoneset [vsan integer]
Syntax Description
active-zoneset
|
The zone name of the active zoneset.
|
full-zoneset
|
The zone name of the full zoneset.
|
vsan
|
Indicates that the active-zoneset.
|
integer
|
The id of the VSAN (1-4096).
|
Defaults
None
Command Modes
EXEC
Usage Guidelines
None.
Examples
switch# zone copy test1 test2 in default vsan only (vsan1)
zone default-zone
To define whether a default zone (nodes not assigned a created zone) will permit or deny access to all in the default zone, use the zone default-zone command. Use the no form of this command to deny.
zone default-zone permit vsan number
Syntax Description
zone
|
Zone configuration command.
|
default-zone
|
Define default zoning behavior.
|
permit
|
Default permit.
|
vsan
|
Defines default zoning behavior for the specified VSAN.
|
number
|
The ID of the VSAN (1-4096).
|
Defaults
permit
Command Modes
Configuration
Usage Guidelines
None
Examples
default-zone Defines default zoning behavior
switch(config)# zone default-zone ?
switch(config)# zone default-zone permit ?
vsan Defines default zoning behavior for the specified VSAN
switch(config)# zone default-zone permit vsan ?
switch(config)# zone default-zone permit vsan 2 ?
zone merge
To merge zone server databases, use the zone merge command. This command can be used to recover from link isolation due to zone merge failure
zone merge interface [fc | port-channel] integer {import | export} vsan vsan int range
Syntax Description
interface
|
The name of the interface.
|
fc integer
|
A Fibre Channel interface. The integer is the slot number.
|
port-channel integer
|
A Port Channel interface. The integer is the Port Channel number.
|
export
|
Exports the zone server database to the adjacent switch on the specified interface. The active zoneset in this switch becomes the activated zoneset of the merged SAN.
|
import
|
Imports the zone server database to the adjacent switch on the specified interface. The active zoneset in the adjacent switch becomes the activated zoneset of the merged SAN.
|
vsan
|
Merges the zone server database of a VSAN on the specified interface.
|
vsan int range
|
The id of the VSAN (1-4096).
|
Defaults
None
Command Modes
EXEC
Usage Guidelines
None.
Examples
switch# zone merge interface port-channel 3 export vsan 3
zone name
To create a zone, use the zone name command.
zone name name vsan number [ exit ] [ member fcalias name | fcid value | fwwn value | pwwn
value ] [ no ]
Syntax Description
zone
|
Zone configuration command.
|
name
|
Configuration zone.
|
name
|
Enter the name of zone (Max Size - 64).
|
vsan
|
Configure a zone on a VSAN.
|
number
|
The ID of the VSAN (1-4096).
|
exit
|
Exit from this submode
|
member
|
Add a member to zone
|
fcalias
|
Add fcalias to zone
|
name
|
Enter the name of fcalias (Max Size - 64)
|
fcid
|
Add FCID member to zone
|
fwwn
|
Add Fabric Port WWN member to zone
|
pwwn
|
Add Port WWN member to zone
|
no
|
Negate a command or set its defaults
|
Defaults
None
Command Modes
Configuration
Usage Guidelines
Zones are assigned to Zoneset, Zoneset are then activated from one switch and propagates across fabric to all switches. Zones allow security by permitting and denying access between nodes (hosts and storage). zone name commands are issued from the config t mode. Configure a zone for a VSAN from the config-zone sub mode.
Examples
switch(config)# zone name ?
<WORD> Enter the name of zone (Max Size - 64)
switch(config)# zone name Somename ?
vsan Configure a zone on a VSAN
switch(config)# zone name Somename vsan ?
switch(config)# zone name somename vsan 1
Configure a zone for a VSAN:
exit Exit from this submode
member Add a member to zone
no Negate a command or set its defaults
Configure a zone for a VSAN:
exit Exit from this submode
member Add a member to zone
no Negate a command or set its defaults
switch(config-zone)# member ?
fcalias Add fcalias to zone
fcid Add FCID member to zone
fwwn Add Fabric Port WWN member to zone
pwwn Add Port WWN member to zone
switch(config-zone)# member fcalias ?
<WORD> Enter the name of fcalias (Max Size - 64)
switch(config-zone)# member fcalias aabb ?
switch(config-zone)# member fcalias aabb
switch(config-zone)# member fcid ?
switch(config-zone)# member fwwn ?
<hh:hh:hh:hh:hh:hh:hh:hh> Enter Fabric Port WWN
switch(config-zone)# member pwwn ?
<hh:hh:hh:hh:hh:hh:hh:hh> Enter Port WWN
switch(config-zone)# member pwwn
zoneset
To group zones under one zoneset, use the zoneset command.
zoneset [ activate name name vsan number ] [distribute full vsan vsan-id][ name string vsan
vsan-id]
Syntax Description
zoneset
|
Zoneset configuration command.
|
activate
|
Activate a zoneset
|
name
|
Zoneset name.
|
name
|
Enter name for zoneset.
|
distribute full
|
Enable zoneset propagation
|
name
|
Configure a zoneset
|
vsan
|
Activate a zoneset on the specified VSAN. The id of the VSAN (1-4096).
|
number
|
The id of the VSAN (1-4096).
|
Defaults
None
Command Modes
Configuration
Usage Guidelines
Zones are activated by activating the parent Zoneset.
Examples
Enter configuration commands, one per line. End with CNTL/Z.
switch(config)# zoneset ?
activate Activates a zoneset
distribute Enable zoneset propagation
name Configures a zoneset
switch(config)# zoneset name ?
<WORD> Enter the name of zoneset
switch(config)# zoneset name gottons ?
vsan Configures a zoneset on a VSAN
switch(config)# zoneset name gottons vsan 333
switch(config-zoneset)# ?
Configures a zoneset for a VSAN:
exit Exit from this submode
member Add zone to zoneset
no Negate a command or set its defaults
zone Configures an __inline__ zone
switch(config-zoneset)# member getsome
switch(config)# zoneset activate name gottons vsan 333
Zoneset Activation initiated. check zone status