Table Of Contents
Using PIX Firewall Commands
Introduction
Tips
For more information
Access Modes
Ports
Protocols
Using PIX Firewall Commands
This chapter introduces the Cisco PIX Firewall Command Reference and contains the following sections:
•
Introduction
•Access Modes
•Ports
•Protocols
Introduction
This section provides a brief introduction to using PIX Firewall commands and where to go for more information on configuring and using your PIX Firewall.
The following table lists some basic PIX Firewall commands.
Task
|
Related Command
|
Saving my configuration
|
write memory
|
Viewing my configuration
|
write terminal
|
Accumulating system log (syslog) messages
|
logging buffered debugging
|
Viewing system log (syslog) messages
|
show logging
|
Clearing the message buffer
|
clear logging
|
Tips
When using the PIX Firewall command-line interface (CLI), you can do the following:
•Check the syntax before entering a command. Enter a command and press the Enter key to view a quick summary, or precede a command with help, as in, help aaa.
•Abbreviate commands. For example, you can use the config t command to start configuration mode, the write t command statement to list the configuration, and write m to write to Flash memory. Also, in most commands, show can be abbreviated as sh. This feature is called command completion.
•After changing or removing the alias, access-list, conduit, global, nat, outbound, and static commands, use the clear xlate command to make the IP addresses available for access.
•Review possible port and protocol numbers at the following IANA websites:
http://www.iana.org/assignments/port-numbers
http://www.iana.org/assignments/protocol-numbers
•Create your configuration in a text editor and then cut and paste it into the configuration. PIX Firewall lets you paste in a line at a time or the whole configuration. Always check your configuration after pasting large blocks of text to be sure everything copied.
For more information
For information about how to build your PIX Firewall configuration, please refer to the
Cisco PIX Firewall and VPN Configuration Guide.
Syslog messages are fully described in Cisco PIX Firewall System Log Messages.
For information about how to use Cisco PIX Device Manager (PDM), please refer to the online Help included in the PDM software (accessed through the PDM application Help button). For information about how to install PDM, please refer to the Cisco PIX Device Manager Installation Guide.
PIX Firewall technical documentation is located online at the following website:
http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/
Access Modes
The PIX Firewall contains a command set based on Cisco IOS technologies and provides configurable command privilege modes:
•Unprivileged mode is available when you first access the PIX Firewall and displays the ">" prompt. This mode lets you view restricted settings.
•Privileged mode displays the "#" prompt and lets you change current settings. Any unprivileged command also works in privileged mode. Use the enable command to start privileged mode and the disable, exit, or quit commands to exit.
•Configuration mode displays the "(config)#" prompt and lets you change system configurations. All privileged, unprivileged, and configuration commands work in this mode. Use the configure terminal command to start configuration mode and the exit or quit commands to exit.
Ports
Lliteral names can be used instead of a numerical port values in commands.
The PIX Firewall permits the following TCP literal names: bgp, chargen, cmd, citrix-ica, daytime, discard, domain, echo, exec, finger, ftp, ftp-data, gopher, h323, hostname, http, ident, irc, klogin, kshell, lpd, nntp, pop2, pop3, pptp, rpc, smtp, sqlnet, sunrpc, tacacs, talk, telnet, time, uucp, whois, and www.
Note PIX Firewall uses port 1521 for SQL*Net. This is the default port used by Oracle for SQL*Net; however, this value does not agree with IANA port assignments.
PIX Firewall listens for RADIUS on ports 1645 and 1646. If your RADIUS server uses ports 1812 and 1813, you will need to reconfigure it to listen on ports 1645 and 1646.
To assign a port for DNS access, use domain, not dns. The dns keyword translates into the port value for dnsix.
Permitted UDP literal names are biff, bootpc, bootps, discard, dnsix, echo, mobile-ip, nameserver, netbios-dgm, netbios-ns, ntp, rip, snmp, snmptrap, sunrpc, syslog, tacacs, talk, tftp, time, who, and xdmcp.
Port numbers can be viewed online at the IANA website:
http://www.iana.org/assignments/port-numbers
Table 2-1 lists the port literal values.
Table 2-1 Port Literal Values
Literal
|
Value
|
Description
|
bgp
|
179
|
Border Gateway Protocol, RFC 1163
|
biff
|
512
|
Used by mail system to notify users that new mail is received
|
bootpc
|
68
|
Bootstrap Protocol Client
|
bootps
|
67
|
Bootstrap Protocol Server
|
chargen
|
19
|
Character Generator
|
citrix-ica
|
1494
|
Citrix Independent Computing Architecture (ICA) protocol
|
cmd
|
514
|
Similar to exec except that cmd has automatic authentication
|
daytime
|
13
|
Day time, RFC 867
|
discard
|
9
|
Discard
|
domain
|
53
|
DNS (Domain Name System)
|
dnsix
|
195
|
DNSIX Session Management Module Audit Redirector
|
echo
|
7
|
Echo
|
exec
|
512
|
Remote process execution
|
finger
|
79
|
Finger
|
ftp
|
21
|
File Transfer Protocol (control port)
|
ftp-data
|
20
|
File Transfer Protocol (data port)
|
gopher
|
70
|
Gopher
|
hostname
|
101
|
NIC Host Name Server
|
nameserver
|
42
|
Host Name Server
|
ident
|
113
|
Ident authentication service
|
irc
|
194
|
Internet Relay Chat protocol
|
isakmp
|
500
|
ISAKMP
|
klogin
|
543
|
KLOGIN
|
kshell
|
544
|
Korn Shell
|
lpd
|
515
|
Line Printer Daemon - printer spooler
|
login
|
513
|
Remote login
|
mobile-ip
|
434
|
MobileIP-Agent
|
netbios-ns
|
137
|
NETBIOS Name Service
|
netbios-dgm
|
138
|
NETBIOS Datagram Service
|
nntp
|
119
|
Network News Transfer Protocol
|
ntp
|
123
|
Network Time Protocol
|
pim-auto-rp
|
496
|
Protocol Independent Multicast, reverse path flooding, dense mode
|
pop2
|
109
|
Post Office Protocol - Version 2
|
pop3
|
110
|
Post Office Protocol - Version 3
|
radius
|
1645, 1646
|
Remote Authentication Dial-In User Service
|
rip
|
520
|
Routing Information Protocol
|
smtp
|
25
|
Simple Mail Transport Protocol
|
snmp
|
161
|
Simple Network Management Protocol
|
snmptrap
|
162
|
Simple Network Management Protocol - Trap
|
sqlnet
|
1521
|
Structured Query Language Network
|
sunrpc
|
111
|
Sun RPC (Remote Procedure Call)
|
syslog
|
514
|
System Log
|
tacacs
|
49
|
TACACS+ (Terminal Access Controller Access Control System Plus)
|
talk
|
517
|
Talk
|
telnet
|
23
|
RFC 854 Telnet
|
tftp
|
69
|
Trivial File Transfer Protocol
|
time
|
37
|
Time
|
uucp
|
540
|
UNIX-to-UNIX Copy Program
|
who
|
513
|
Who
|
whois
|
43
|
Who Is
|
www
|
80
|
World Wide Web
|
xdmcp
|
177
|
X Display Manager Control Protocol, used to communicate between X terminals and workstations running UNIX
|
Protocols
Possible literal values are ahp, eigrp, esp, gre, icmp, igmp, igrp, ip, ipinip, ipsec, nos, ospf, pcp, snp, tcp, and udp. You can also specify any protocol by number. The esp and ah protocols only work in conjunction with Private Link.
Protocol numbers can be viewed online at the IANA website:
http://www.iana.org/assignments/port-numbers
Note Many routing protocols use multicast packets to transmit their data. If you send routing protocols across the PIX Firewall, configure the surrounding routers with the Cisco IOS software neighbor command. If routes on an unprotected interface are corrupted, the routes transmitted to the protected side of the firewall will pollute routers there as well.
Table 2-2 lists the numeric values for the protocol literals.
Table 2-2 Protocol Literal Values
Literal
|
Value
|
Description
|
ah
|
51
|
Authentication Header for IPv6, RFC 1826
|
eigrp
|
88
|
Enhanced Interior Gateway Routing Protocol
|
esp
|
50
|
Encapsulated Security Payload for IPv6, RFC 1827
|
gre
|
47
|
General Routing Encapsulation
|
icmp
|
1
|
Internet Control Message Protocol, RFC 792
|
igmp
|
2
|
Internet Group Management Protocol, RFC 1112
|
igrp
|
9
|
Interior Gateway Routing Protocol
|
ip
|
0
|
Internet Protocol
|
ipinip
|
4
|
IP-in-IP encapsulation
|
nos
|
94
|
Network Operating System (Novell's NetWare)
|
ospf
|
89
|
Open Shortest Path First routing protocol, RFC 1247
|
pcp
|
108
|
Payload Compression Protocol
|
snp
|
109
|
Sitara Networks Protocol
|
tcp
|
6
|
Transmission Control Protocol, RFC 793
|
udp
|
17
|
User Datagram Protocol, RFC 768
|
