Table A-2 EVC Command Summary
Command
|
Purpose
|
Router(config-if-srv)# [bridge-domain bridge-id
|
Binds the service instance to a bridge-domain instance.
|
Router(config-if-srv)# connect evc-name interface1 efp-id1 interface2 efp-id2
|
Creates a direct and transparent connection between two service instances.
|
Router#debug ethernet service evc [id evc-id]
|
Enables Ethernet virtual connection (EVC) debugging. If no EVC ID is specified, debugging is enabled for all EVCs on the system.
|
Router#debug ethernet service instance [id instance-id interface interface-id | interface interface-id]
|
Enables service instance debugging. If no options are specified, debugging for all service instances is enabled. If a service instance ID and interface are specified, only debug messages for the associated service instance are output. If only an interface is specified, debug messages for all service instances on that interface are displayed.
|
Router#debug ethernet service interface [interface-id]
|
Enables Port Data Block (PDB) debugging.
|
Router#debug ethernet service api
|
Enables debugging between Ethernet Services Infrastructure and its clients.
|
Router#debug ethernet service oam-mgr
|
Enables OAM Manager debugging, to debug OAM inter-working.
|
Router#debug ethernet service error
|
Enables ethernet service error debugging.
|
Router#debug ethernet service all
|
Enables all EI debugging messages for all PDBs, EVCs and service instances.
|
Router#ethernet evc service-name
|
Creates an EVC (or a Customer Service Instance) on global configuration mode. It sets the device into the config-srv submode.
|
Router(config-if-srv)#encapsulation untagged
|
Defines the matching criteria to be used in order to map untagged Ethernet frames ingress on an interface to the appropriate service instance.
|
Router(config-if-srv)#encapsulation default
|
Configures the default service instance on a port. Anything that does not meet the criteria of other service instances on the same physical interface falls into this service instance
|
Router(config-if-srv)#encapsulation dot1q vlan-id[,vlan-id[-vlain-id]] [native]
|
Defines the matching criteria to be used in order to map dot1q frames ingress on an interface to the appropriate service instance. The criteria for this command are: single VLAN, range of VLANs and lists of the previous two.
|
Router(config-if-srv)#encapsulation dot1ad vlan-id[,vlan-id[-vlain-id]] [native]
|
Defines the matching criteria to be used in order to map single-tagged 802.1ad frames ingress on an interface to the appropriate service instance. The criteria for this command are: single VLAN, range of VLANs and lists of the previous two.
|
Router(config-if-srv)#encapsulation dot1q <vlan-id> second-dot1q {any | vlan-id[,vlan-id[-vlain-id]]}
|
Defines the matching criteria to be used in order to map QinQ frames ingress on an interface to the appropriate service instance. The criteria for this command are: outer tag must be unique and inner tag may be single VLAN, range of VLANs or lists of the previous two.
|
Router(config-if-srv)#encapsulation dot1ad <vlan-id> dot1q {any | vlan-id[,vlan-id[-vlain-id]]}
|
Defines the matching criteria to be used in order to map double-tagged 802.1ad frames ingress on an interface to the appropriate service instance. The criteria for this command are: outer tag must be unique and inner tag may be single VLAN, range of VLANs or lists of the previous two.
|
Router(config-if-srv)#rewrite ingress tag {push {dot1q vlan-id | dot1q vlan-id second-dot1q vlan-id | dot1ad vlan-id dot1q vlan-id} | pop {1 | 2} | translate {1-to-1 {dot1q vlan-id | dot1ad vlan-id}| 2-to-1 dot1q vlan-id | dot1ad vlan-id}| 1-to-2 {dot1q vlan-id second-dot1q vlan-id | dot1ad vlan-id dot1q vlan-id} | 2-to-2 {dot1q vlan-id second-dot1q vlan-id | dot1ad vlan-id dot1q vlan-id}} [symmetric]
|
Specifies the encapsulation adjustment that is to be performed on the frame ingress to the service instance.
|
Router(config-if-srv)#service instance id {Ethernet [service-name]}
|
Creates an service instance (instantiation of an EVC) on an interface. It sets the device into the config-if-srv sub-mode.
|
Router#show ethernet service evc [id evc-id | interface interface-id] [detail]
|
Displays information pertaining to a specific EVC if an EVC ID is specified, or pertaining to all EVCs on an interface if an interface is specified. The detailed option provides additional information on the EVC.
|
Router#show ethernet service instance [id <instance-id> interface interface-id | interface interface-id] [detail]
|
Displays information about one or more service instances: If a service instance ID and interface are specified, only data pertaining to that particular service instance will be displayed. If only an interface ID is specified, this command will display data for all service instances on the given interface.
|
Router#show ethernet service interface [interface-id] [detail]
|
Displays information in the PDB.
|
Router(config-if-srv)#xconnect peer-id vc-id encapsulation mpls
|
Configures scalable EoMPLS on a service instance. On the ingress side, after proper encapsulation manipulations, the packet is tunneled in a EoMPLS VC and transmitted on the core.
|
Feedback
keepalive command in the interface configuration mode is not supported in a ES20 line card.
