Table Of Contents
Configuring GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Cards Using PCLI
Before You Begin
NTP-G222 Access PCLI Text Interface
NTP-G223 Create a Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G517 Create an Ingress Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards Using PCLI
DLP-G518 Create a Egress Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G519 Create a Service Instance Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G520 Apply an Ingress Policy to a Port on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G521 Apply an Egress Policy to a Port on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G522 Apply a Service Instance Policy to a Port on GE_XPE or 10GE_XPE Cards Using PCLI
NTP-G226 Enable MAC Address Learning on SVLANs for GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
NTP-G216 Enable Link Integrity on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
NTP-G225 Provision SVLAN Rate Limiting on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Card Using PCLI
NTP-G220 Enable IGMP Snooping on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
NTP-G217 Enable IGMP Fast-Leave Processing on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
NTP-G218 Configure a Multicast Router Port on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
NTP-G219 Enable IGMP Report Suppression on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
NTP-G224 Enable MVR on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
NTP-G227 Create SVLAN for GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
NTP-G228 Create a Service Instance Using PCLI
NTP-G282 Configure the Channel Group on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G619 Create a Channel Group on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G620 Add Ports to a Channel Group on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
NTP-G286 Configure EFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G643 Enable EFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G644 Configure the EFM Mode on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
NTP-G284 Configure CFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G635 Enable CFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G636 Create a Maintenance Domain on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G637 Create a Maintenance Intermediate Point on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G638 Create a Maintenance End Point on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
NTP-G288 Configure REP on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G649 Create a Segment on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G650 Configure STCN on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
DLP-G651 Configure Preemption Delay on the Primary Edge Port Using PCLI
DLP-G652 Configure VLAN Load Balancing on the Primary Edge Port Using PCLI
Configuring GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Cards Using PCLI
This chapter explains how to provision GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE cards using Pseudo Command Line Interface (PCLI).
Note 
The procedures and tasks described in this chapter for the Cisco ONS 15454 platform is applicable to the Cisco ONS 15454 M2 and Cisco ONS 15454 M6 platforms, unless noted otherwise.
Note Unless otherwise specified, "ONS 15454" refers to both ANSI and ETSI shelf assemblies.
Before You Begin
Before performing any of the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS 15454 DWDM Troubleshooting Guide as necessary.
Caution Provisioning TXP and MXP cards can be service affecting. You should make all changes during a scheduled maintenance window.
This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).
•G222 Access PCLI Text Interface.
•G223 Create a Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI.
•G216 Enable Link Integrity on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI.
•G220 Enable IGMP Snooping on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI.
•G217 Enable IGMP Fast-Leave Processing on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI.
•G218 Configure a Multicast Router Port on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI.
•G219 Enable IGMP Report Suppression on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI.
•G224 Enable MVR on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI.
•G225 Provision SVLAN Rate Limiting on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Card Using PCLI.
•G226 Enable MAC Address Learning on SVLANs for GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI.
•G227 Create SVLAN for GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI.
•G282 Configure the Channel Group on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G286 Configure EFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G284 Configure CFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G288 Configure REP on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
NTP-G222 Access PCLI Text Interface
Purpose
|
This procedure explains how to access PCLI text interface using CTC or Telnet.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
None
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Retrieve or higher
|
Step 1 Complete the "DLP-G46 Log into CTC" task at the node where you want to access PCLI. If you are already logged in, continue with Step 2.
Step 2 PCLI can be accesses in the following ways:
•To access PCLI text interface using CTC, select Tools > Open Pseudo IOS Connection menu option or right-click on the node in the Network View and select Open Pseudo IOS Connection.
•To access PCLI from the command prompt, telnet or SSH may be used depending on the access state set for PCLI access in Provisioning > Security > Pseudo IOS Access in Node view. If the access state is set to the default state, non-secure, a PCLI session can be established using telnet as shown in the following procedure:
| |
Command or Action
|
Purpose
|
Step 1
|
telnet <node ip or node name> <port
number>
Example:
telnet 10.76.148.176 65000
MSTP-176>
|
Establishes a PCLI session using Telnet.
Note The default port number for non-secure mode is 65000. The port number can be provisioned in CTC. To do so, go to Node view and click Provisioning > Security > Pseudo IOS Access.
|
Step 2
|
Example:
MSTP-176> exit
|
Exits PCLI text interface.
|
Step 3
|
Example:
MSTP 176# enable 1/12
|
Enters the Privileged EXEC mode from where you can enter other configuration modes. Several show commands are also available in the Privileged EXEC mode.
|
| |
Stop. You have completed this procedure.
|
—
|
•If the access state is set to secure, a PCLI session can be established using a SSH client like Open SSH as shown in the following procedure:
| |
Command or Action
|
Purpose
|
Step 1
|
ssh -p <node ip or node name > <port
number>
Example:
ssh -p 10.76.148.194 64000
MSTP-176>
|
Establishes a PCLI session using SSH.
Note The default port number for secure mode is 64000. The port number can be provisioned in CTC. To do so, go to Node view and click Provisioning > Security > Pseudo IOS Access.
|
Step 2
|
Example:
MSTP-176> exit
|
Exits PCLI text interface.
|
Step 3
|
Example:
MSTP 176> enable 1/12
|
Enters the Privileged EXEC mode from where you can enter other configuration modes. Several show commands are also available in the Privileged EXEC mode.
For more information on PCLI commands see the Cisco ONS DWDM Reference Manual.
|
| |
Stop. You have completed this procedure.
|
—
|
Stop. You have completed this procedure.
NTP-G223 Create a Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to create a policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
None
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to create a policy. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
•G517 Create an Ingress Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards Using PCLI
•G518 Create a Egress Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G519 Create a Service Instance Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G520 Apply an Ingress Policy to a Port on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G521 Apply an Egress Policy to a Port on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G522 Apply a Service Instance Policy to a Port on GE_XPE or 10GE_XPE Cards Using PCLI
Stop. You have completed this procedure.
DLP-G517 Create an Ingress Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards Using PCLI
Purpose
|
This procedure explains how to create CIR, EIR, CBS, EBS and Ingress COS parameters as part of Ingress policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
None
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note Once the CIR, EIR, CBS, EBS and Ingress COS parameters are created, the policy can be used across other cards of these types in the node. See "DLP-G520 Apply an Ingress Policy to a Port on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI" task.
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176# configure terminal
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) policy-map pmap
|
Enters policy map configuration mode.
|
Step 3
|
police cir percent % bc bytes be bytes
Example:
MSTP-176(config-pmap)#police cir
percent 20 bc 64 be 128
|
Sets CIR, EIR, CBS and EBS values.
|
Step 4
|
Example:
MSTP 176# (config) (config-pmap)# set cos 6
|
Sets the Ingress COS parameter.
|
Step 5
|
Example:
MSTP-176(config-pmap# exit
|
Exits policy map configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
DLP-G518 Create a Egress Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to create an egress policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
None
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note Once the Egress policy is created, the policy can be used across other cards of these types in the node. "DLP-G521 Apply an Egress Policy to a Port on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI" task.
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) policy-map pmap
|
Enters policy map configuration mode.
|
Step 3
|
wrr-queue cos-map <queue-id> <cos1>
Example:
MSTP-176(config-pmap)#wrr-queue cos-map
1 1
|
Maps a queue ID to a given COS.
|
Step 4
|
wrr-queue <queue-id> weight <1-16>
bandwidth percent <%>
Example:
MSTP 176# configure terminal
(config-pmap)# wrr-queue 1
weight 2 band per 90
|
Sets the WRR and bandwidth values on a queue.
|
Step 5
|
Example:
MSTP-176(config-pmap# exit
|
Exits policy map configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
DLP-G519 Create a Service Instance Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to create a service instance policy which can be used to define a COS for a CVLAN on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
None
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note Once the service instance policy is created, the policy can be used across other cards of these types in the node. "DLP-G522 Apply a Service Instance Policy to a Port on GE_XPE or 10GE_XPE Cards Using PCLI" task
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176# (config)
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) policy-map pmap
|
Enters policy map configuration mode.
|
Step 3
|
Example:
MSTP 176 (config-pmap)# set cos 6
|
Sets the COS value.
|
Step 4
|
Example:
MSTP-176(config-pmap)# exit
|
Exits policy map configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
DLP-G520 Apply an Ingress Policy to a Port on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to apply an Ingress policy to a port on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
•Complete G517 Create an Ingress Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards Using PCLI.
•Before you apply the Ingress policy on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE card, make sure the port is shutdown.
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176# configure terminal
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) interface giga 1
|
Enters interface configuration mode.
|
Step 3
|
service-policy input <name>
Example:
MSTP 176# (config) (config-if)# service-pol input
ingresspolicy1
|
Maps the specified ingress policy to the port.
|
Step 4
|
Example:
MSTP-176(config-if# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
DLP-G521 Apply an Egress Policy to a Port on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) interface giga 1
|
Enters interface configuration mode.
|
Step 3
|
service-policy output <name>
Example:
MSTP 176# configure terminal
(config-if)# service-policy
output egresspolicy1
|
Maps the specified Egress policy to the port.
|
Step 4
|
Example:
MSTP-176(config-if)# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
DLP-G522 Apply a Service Instance Policy to a Port on GE_XPE or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to apply a service instance policy to a port on GE_XPE or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
•Complete G519 Create a Service Instance Policy on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI.
•Before you apply the Egress policy on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE card, make sure the port is shutdown.
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note A service instance cannot be edited on a a port using PCLI. The service instance policy must be specified at the time of service instance creation.
Step 1
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176# (config)
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) interface giga 1
|
Enters interface configuration mode.
|
Step 3
|
service instance ethernet vlan
Example:
MSTP 176# (config-if) service instance
ethernet vlan1
MSTP-176# (config-if-srv)#
|
Enters service instance configuration mode.
|
Step 4
|
rewrite ingress tag translate 1-to-1
<multipurpose vlan> push dot1q <svlan>
Example:
MSTP 176 (config-if-srv)# rewrite
ingress tag translate 1 1 push dot1 1
|
Specifies the CVLAN and SVLAN relation on the port.
|
Step 5
|
service policy input <policy name>
Example:
MSTP 176# configure terminal
(config-if-srv)#
service-policy input
serviceinstancepolicy1
|
Associates the service instance policy specified to a port.
|
Step 6
|
Example:
MSTP-176(config-if-srv)# exit
MSTP-176(config-if)#
|
Exits service instance configuration mode.
|
Step 7
|
Example:
MSTP-176(config-if)# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
Complete the following tasks, as needed:
NTP-G226 Enable MAC Address Learning on SVLANs for GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to enable MAC address learning on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
G222 Access PCLI Text Interface
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to enable MAC address learning. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176# (config)
|
Selects shelf and slot to be configured for a card.
|
Step 2
|
Example:
MSTP 176
|
Enters global configuration mode.
|
Step 3
|
mac-address-table learning vlan
<vlan-id>
Example:
MSTP-176(config)# mac-address-table
learning vlan 2
|
Enables interface based learning of MAC address. Repeat the command on each SVLAN to enable MAC address learning.
|
Step 4
|
mac-address-table learning interface
<type> <port>
Example:
MSTP-176(config)# mac-address-table
learning gigabitethernet 2
|
Enables interface based learning of MAC address. Repeat the command on each SVLAN to enable MAC address learning.
|
Step 5
|
Example:
MSTP-176(config)# exit
|
Exits global configuration mode.
|
Step 6
|
Return to your originating procedure (NTP).
|
—
|
NTP-G216 Enable Link Integrity on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to enable link integrity on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
G222 Access PCLI Text Interface
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to enable link integrity. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176# configure terminal
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) (config)# vlan profile
profile4
MSTP 176# (config-if) service instance
ethernet vlan1
(config-profile)
|
Enters VLAN profile configuration mode.
|
Step 3
|
Example:
MSTP 176 (config-profile) link
integrity
|
Enables link integrity.
|
Step 4
|
Example:
MSTP-176(config-profile)# exit
|
Exits VLAN profile configuration mode.
|
Step 5
|
vlan profile name vlan svlanid
interface type port
Example:
MSTP 176 (config)# vlan profile a vlan
2 interface gigabitethernet 2
|
Associates the SVLAN profile to a SVLAN on a port.
|
Step 6
|
interface type port
Example:
MSTP 176 (config)# interface
gigabitethernet 2
|
Enters interface configuration mode.
|
Step 7
|
link integrity action {none | squelch |
propagate}
Example:
MSTP 176 (config-if)# link integrity
action squelch
|
When an AIS packet is received on a SVLAN terminating on the UNI port, the UNI port is squelched.
|
Step 8
|
Example:
MSTP-176(config-profile)# exit
|
Exits interface configuration mode.
|
Step 9
|
Return to your originating procedure (NTP).
|
—
|
NTP-G225 Provision SVLAN Rate Limiting on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Card Using PCLI
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to provision SVLAN rate limiting. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# enable 1/12
(config)# vlan profile
profile4
MSTP 176# configure terminal
(config-profile)
|
Enters VLAN profile configuration mode.
|
Step 3
|
police cir percent <%> pir percent <%>
Example:
MSTP-176(config-profile)# police cir
percent 20 bc 64 be 128
|
Enters ingress rate limits.
|
Step 4
|
Example:
MSTP-176(config-profile)# exit
|
Exits VLAN profile configuration mode.
|
Step 5
|
vlan profile name vlan svlanid
interface type port
Example:
MSTP 176 (config)# vlan profile a vlan
2 interface gigabitethernet 2
|
Associates the SVLAN profile to a SVLAN on a port.
|
Step 6
|
Return to your originating procedure (NTP).
|
—
|
NTP-G220 Enable IGMP Snooping on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to enable IGMP snooping on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
None
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to enable IGMP snooping. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176# configure terminal
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP-176# (config)# vlan 2
|
Enters VLAN configuration mode.
|
Step 3
|
Example:
MSTP-176(config-vlan)# ip igmp snooping
|
Enables IGMP snooping.
Note To disable IGMP snooping, use the no ip igmp snooping command.
|
Step 4
|
Example:
MSTP-176(config-vlan)# exit
|
Exits VLAN configuration mode.
|
Step 5
|
Return to your originating procedure (NTP)
|
—
|
NTP-G217 Enable IGMP Fast-Leave Processing on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to enable fast-leave processing on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
None
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to enable IGMP fast-leave processing. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176# configure terminal
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP-176# (config)# vlan 2
|
Enters VLAN configuration mode.
|
Step 3
|
ip igmp snooping immediate-leave
Example:
MSTP-176(config-vlan)# ip igmp snooping
immediate-leave
|
Enables IGMP fast-leave processing.
Note To disable fast-leave processing, use the no ip igmp snooping immediate-leave configuration command.
|
Step 4
|
Example:
MSTP-176(config-vlan)# exit
|
Exits VLAN configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
NTP-G218 Configure a Multicast Router Port on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to configure multicast router port on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
None
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to configure multicast router ports. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176
|
Enters global configuration mode.
|
Step 2
|
interface {gigabitethernet |
tengigabitethernet} port
Example:
MSTP-176(config)# interface gigabitethernet
1
MSTP-176(config-if)#
|
Enters interface configuration mode.
|
Step 3
|
Example:
MSTP-176(config-if)# ip igmp snooping
mrouter
|
Enables multicast router port functionality on a port.
Note To disable multicast router functionality on the port, enter interface configuration mode, and use the
no ip igmp snooping mrouter command.
|
Step 4
|
Example:
MSTP-176(config-if)# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
NTP-G219 Enable IGMP Report Suppression on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains to how enable IGMP report suppression on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
None
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to enable report suppression. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP-176# (config)# vlan 2
|
Enters VLAN configuration mode.
|
Step 3
|
ip igmp snooping report-suppression
Example:
MSTP-176(config-vlan))# ip igmp snooping
report-suppression
|
Globally enables IGMP snooping report suppression.
Note To disable report suppression, use the no ip igmp snooping report-suppression in VLAN configuration mode.
|
Step 4
|
Example:
MSTP-176(config-vlan)# exit
|
Exits VLAN configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
NTP-G224 Enable MVR on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to enable MVR on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
None
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to enable MVR. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176
|
Enters global configuration mode.
|
Step 2
|
mvr group ip-address count
Example:
MSTP-176(config)# mvr group 228.1.23.4
|
Specify the starting IP address for a range of multicast group addresses for which MVR needs to be enabled. Use the count parameter to limit the number of groups.
Note A maximum of 256 MVR multicast groups can be configured on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE card.
Note MVR is applied only on multicast groups configured here. For multicast groups that are not in this range, normal IGMP processing occurs.
Note Count can be set from 1 to 256. Use 1 to enable MVR on a single group. The IP address range must be 224.0.0.0 to 239.255.255.255.
|
Step 3
|
Example:
MSTP-176(config)# mvr vlan 2
|
Specifies the VLAN in which multicast data is received; all ports must belong to this VLAN. The VLAN range is 1 to 4093.
|
Step 4
|
Example:
MSTP-176(config)# mvr
|
Enables MVR.
Note To disable MVR, use the no mvr in global configuration mode.
|
Step 5
|
Example:
MSTP-176(config-if)# exit
|
Exits global configuration mode.
|
Step 6
|
Return to your originating procedure (NTP).
|
—
|
NTP-G227 Create SVLAN for GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to create or delete SVLANs on GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
None
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to create an SVLAN. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176# configure terminal
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP-176# (config)# vlan 2
|
Creates a VLAN.
Note To delete an SVLAN, use the no config vlan <vlan-id> command in global configuration mode.
|
Step 3
|
Example:
MSTP-176(config)# exit
|
Exits global configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
NTP-G228 Create a Service Instance Using PCLI
Purpose
|
This procedure explains how to create a service instance that is used to define the VLAN configuration on the UNI and NNI ports of GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
Create SVLANs that you want to include in the service instance.
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to create an SVLAN. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) interface giga 1
|
Enters interface configuration mode.
|
Step 3
|
service instance ethernet vlan
Example:
MSTP 176# (config-if)# service instance
ethernet vlan10
MSTP-176# (config-if-srv)#
|
Enters service instance configuration mode.
If the port is configured as a UNI, then go to Step 4. If the port is configured as an NNI port, go to step Step 14.
|
Step 4
|
Example:
MSTP 176# (config-if-srv)# encapsulation
default
|
Configures the port in transparent mode.
Note Before executing this command, the ports must be in disabled state.
Note The encapsulation and rewrite commands must be executed as pairs. Every rewrite command must be preceeded by an encapsulation command. Only one encapsulation and rewrite command pair can be executed per port.
|
Step 5
|
rewrite ingress tag push dot1q <svlan>
Example:
MSTP 176 (config-if-srv)# rewrite ingress tag
push dot1q 10
|
Note Before executing this command, the ports must be in disabled state.
Note The encapsulation and rewrite commands must be executed as pairs. Every rewrite command must be preceeded by an encapsulation command. Only one encapsulation and rewrite command pair can be executed per port.
|
Step 6
|
encapsulation dot1q <first cvlan> <last cvlan>
Example:
MSTP 176# configure terminal
(config-if-srv)# encapsulation dot1
20 30
|
Configures a port in selective add mode with a range of CVLANs mapped to a given SVLAN.
Tagged frames with VLAN ID in the range between 20 to 30 (Inclusive of 20 and 30) are matched.
|
Step 7
|
rewrite ingress tag push dot1q <svlan>
Example:
MSTP 176# configure terminal
(config-if-srv)# rewrite ingress tag
push dot1q 10
|
Note Before executing this command, the ports must be in disabled state.
Note The encapsulation and rewrite commands must be executed as pairs. Every rewrite command must be preceeded by an encapsulation command. Only one encapsulation and rewrite command pair can be executed per port.
Note Multiple encapsulation and rewrite commands can be configured as part of the same service instance.
|
Step 8
|
encapsulation dot1q <first cvlan> <last cvlan>
Example:
MSTP 176# configure terminal
(config-if-srv)# encapsulation dot1
20 20
|
Configures a port in selective translate mode.
Tagged frames with VLAN ID 20 are matched.
|
Step 9
|
rewrite ingress tag translate 1-to-1 <svlan>
Example:
MSTP 176# configure terminal
(config-if-srv)# rewrite ingress tag
translate 1 10
|
Overwrites the Ingress tag 20 with the SVLAN tag value of 10.
Note No two encapsulation and rewrite commands on the port that are configured either as part of a given service instance or as a different service instance can have the same SVLAN.
|
Step 10
|
Example:
MSTP 176# configure terminal
(config-if-srv)# encapsulation
untagged
|
Configures a port in double add mode.
To match untagged packets specify CVLAN to be 0.
|
Step 11
|
rewrite ingress tag push dot1q <multipurpose
vlan> second-dot1q <svlan>
Example:
MSTP 176# configure terminal
(config-if-srv)# rewrite ingress tag
push dot1q 10 second-dot1q 20
|
To add two SVLAN tags to the Ingress untagged packet.
Note Only one encapsulation and rewrite command pair can be executed per port.
Note This configuration is supported only on GE_XPE & 10 GE_XPE cards.
|
Step 12
|
encapsulation dot1q <first cvlan> <last cvlan>
Example:
MSTP 176# configure terminal
(config-if-srv)# encapsulation dot1q
9 9
|
Matches tagged frames with VLAN ID, 9.
|
Step 13
|
rewrite ingress tag translate 1-to-1
<multipurpose vlan> push dot1q <svlan>
Example:
MSTP 176# (config) (config-if-srv)# rewrite ingress tag
translate 1 25 push dot1 30
|
Translates CVLAN tag to SVLAN tag 25 and adds another SVLAN tag, 30.
Note This configuration is supported only on GE_XPE & 10 GE_XPE cards.
|
Step 14
|
Example:
MSTP 176# (config-if)# service instance
ethernet vlan10
(config-if-srv)# bridge-domain 10
|
Adds the port to SVLAN 10.
|
Step 15
|
Example:
MSTP 176# (config-if-srv)# exit
encapsulation
default
(config-if)#
|
Exits service instance configuration mode.
|
Step 16
|
Example:
MSTP 176# (config-if)# exit
MSTP-176(config)#
|
Exits interface configuration mode.
|
Step 17
|
Example:
MSTP-176(config)# exit
|
Exits global configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
NTP-G282 Configure the Channel Group on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to create and configure the channel group on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to create and configure the channel group. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
•G619 Create a Channel Group on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G620 Add Ports to a Channel Group on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Stop. You have completed this procedure.
DLP-G619 Create a Channel Group on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to create a channel group and change the channel group mode on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note You can create up to 11 channel groups on GE_XP and GE_XPE cards and up to 2 channel groups on 10GE_XP and 10GE_XPE cards.
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176#
|
Enters global configuration mode.
|
Step 2
|
interface channel-group number
Example:
MSTP 176(config)# interface
channel-group 7
|
Creates a channel group with id 7.
|
Step 3
|
Example:
MSTP 176#(config)# interface 1
MSTP-176# (config-if)#
|
Enters interface configuration mode.
|
Step 4
|
Example:
MSTP 176# (config-if)# mode passive
|
Sets a channel group mode to passive.
|
Step 5
|
Example:
MSTP-176(config-if)# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
DLP-G620 Add Ports to a Channel Group on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to add ports to a channel group on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note You can assign up to eight ports to a channel group on the GE_XP and GE_XPE cards and up to three ports on the 10GE_XP and 10GE_XPE cards.
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176#
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) interface giga 15
MSTP-176# (config-if)#
|
Enters interface configuration mode.
|
Step 3
|
channel-group port-number
Example:
MSTP 176# (config-if)# channel-group 1
|
Adds a port to a channel group.
|
Step 4
|
Example:
MSTP-176(config-if)# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
NTP-G286 Configure EFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to configure EFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to configure EFM. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
•G643 Enable EFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G644 Configure the EFM Mode on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Stop. You have completed this procedure.
DLP-G643 Enable EFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to enable EFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note EFM is enabled on an interface.
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176#
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) interface giga 1
MSTP-176# (config-if)#
|
Enters interface configuration mode.
|
Step 3
|
ethernet oam mode efm_mode
Example:
MSTP 176# (config-if)# ethernet oam mode
passive
|
Enables EFM on an interface.
|
Step 4
|
Example:
MSTP-176(config-if)# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
DLP-G644 Configure the EFM Mode on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to configure the EFM mode on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176#
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) interface giga 1
MSTP-176# (config-if)#
|
Enters interface configuration mode.
|
Step 3
|
ethernet oam mode efm-mode
Example:
MSTP 176# (config-if)# ethernet oam mode
passive
|
Sets the EFM mode to passive.
|
Step 4
|
Example:
MSTP-176(config-if)# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
NTP-G284 Configure CFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to configure CFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to configure CFM. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
•G635 Enable CFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G636 Create a Maintenance Domain on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G637 Create a Maintenance Intermediate Point on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G638 Create a Maintenance End Point on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Stop. You have completed this procedure.
DLP-G635 Enable CFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to enable CFM on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176#
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# # ethernet cfm ieee
|
Enables CFM on the card.
|
Step 3
|
Example:
MSTP-176(config)# exit
|
Exits global configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
DLP-G636 Create a Maintenance Domain on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to create a maintenance domain on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176#
|
Enters global configuration mode.
|
Step 2
|
ethernet cfm domain domain_name level
level
Example:
MSTP 176# (config)# ethernet cfm domain
test_domain level 4
|
Creates a maintenance domain with a specific maintenance level.
|
Step 3
|
Example:
MSTP-176(config)# exit
|
Exits global configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
DLP-G637 Create a Maintenance Intermediate Point on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to create a Maintenance Intermediate Point (MIP) on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176# configure terminal
|
Enters global configuration mode.
|
Step 1
|
Example:
MSTP 176# (config) interface giga 1
MSTP-176# (config-if)#
|
Enters interface configuration mode.
|
Step 2
|
ethernet cfm mip level level vlan vlan
Example:
MSTP 176(config)# interface
channel-group 7
(config-if)# ethernet cfm mip
level 4 vlan 100
|
Creates a MIP and configures the MIP parameters.
|
Step 3
|
Example:
MSTP-176(config-if)# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
DLP-G638 Create a Maintenance End Point on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to create a Maintenance End Point (MEP) on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176#(config)
|
Enters global configuration mode.
|
Step 1
|
Example:
MSTP 176# (config) interface giga 1
MSTP-176# (config-if)#
|
Enters interface configuration mode.
|
Step 2
|
ethernet cfm mep domain domain_name
mepid mepid vlan vlan
Example:
(config-if)# ethernet cfm mep
domain test_mep mepid 100 vlan 200
|
Creates a MEP and configures the MEP parameters.
|
Step 3
|
Example:
MSTP-176(config-if)# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
NTP-G288 Configure REP on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to configure REP on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Note For detailed information on PCLI, see the Cisco ONS 15454 DWDM Reference Manual.
Step 1 Complete the "NTP-G222 Access PCLI Text Interface" task at the node where you want to configure REP. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
•G649 Create a Segment on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G650 Configure STCN on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
•G651 Configure Preemption Delay on the Primary Edge Port Using PCLI
•G652 Configure VLAN Load Balancing on the Primary Edge Port Using PCLI
Stop. You have completed this procedure.
DLP-G649 Create a Segment on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to enable REP on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) interface giga 1
MSTP-176# (config-if)#
|
Enters interface configuration mode.
|
Step 3
|
rep segment id edge primary
Example:
MSTP 176# (config-if) rep segment 10
edge primary
|
Enables REP on a port and assigns a segment ID to the port. This command also configures the port as the primary edge port.
|
Step 4
|
Example:
MSTP 176# (config-if) rep segment 10
edge
|
Configures the port as the secondary edge port.
|
Step 5
|
rep segment id edge no-neighbor
Example:
MSTP 176# (config-if) rep segment 10
edge no-neighbor
|
Specifies that the edge port must not have a neighbor port.
|
Step 6
|
Example:
MSTP 176# (config-if) rep segment 10
preferred
|
Configures the edge port as a preferred alternate port.
|
Step 7
|
Example:
MSTP-176(config-if)# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
DLP-G650 Configure STCN on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards Using PCLI
Purpose
|
This procedure explains how to configure segment topology change notifications (STCNs) on the GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE cards using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176# configure terminal
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) interface giga 1
MSTP-176# (config-if)#
|
Enters interface configuration mode.
|
Step 3
|
Example:
MSTP 176# (config) (config-if)# rep stcn segment
25
|
Configures a edge port to send REP STCNs to a specific segment.
|
Step 4
|
Example:
MSTP 176 (config-if)# rep stcn
interface 10
|
Configures a edge port to send REP STCNs to a specific interface.
|
Step 5
|
Example:
MSTP-176(config-if)# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
DLP-G651 Configure Preemption Delay on the Primary Edge Port Using PCLI
Purpose
|
This procedure explains how to configure preemption time delay on a primary edge port using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) interface giga 1
MSTP-176# (config-if)#
|
Enters interface configuration mode.
|
Step 3
|
rep preempt delay seconds
Example:
MSTP 176# configure terminal
(config-if)# rep preempt delay
100
|
Configures preemption time delay of 100 seconds on the primary edge port.
|
Step 4
|
Example:
MSTP-176(config-if)# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
DLP-G652 Configure VLAN Load Balancing on the Primary Edge Port Using PCLI
Purpose
|
This procedure explains how to configure VLAN load balancing on a primary edge port using PCLI.
|
Tools/Equipment
|
None
|
Prerequisite Procedures
|
"NTP-G222 Access PCLI Text Interface" task
|
Required/As Needed
|
As needed
|
Onsite/Remote
|
Onsite or remote
|
Security Level
|
Provisioning or higher
|
Step 1 Complete the following tasks, as needed:
| |
Command or Action
|
Purpose
|
Step 1
|
Example:
MSTP 176# (config)
|
Enters global configuration mode.
|
Step 2
|
Example:
MSTP 176# (config) interface giga 1
MSTP-176# (config-if)#
|
Enters interface configuration mode.
|
Step 3
|
rep block port id port_id vlan
vlan_list
Example:
MSTP 176 (config-if)# rep block port id
0X0080001647FB1780 vlan 1-100
|
Configures the alternate port to block VLANs 1 to 100.
|
Step 4
|
rep block port preferred vlan vlan_list
Example:
MSTP 176# configure terminal
(config-if)# rep block port
preferred vlan 1-100
|
Configures VLAN load balancing for the preferred port.
|
Step 5
|
Example:
MSTP-176(config-if)# exit
|
Exits interface configuration mode.
|
| |
Stop. You have completed this procedure.
|
—
|
Feedback
