qos_mqc_xe

QoS: Packet Matching Statistics

First Published: March 28, 2011
Last Updated: March 29, 2011

The QoS: Packet Matching Statistics feature allows you to define a quality of service (QoS) packet filter, then display the number of packets and bytes matching that filter.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for QoS: Packet Matching Statistics" section.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

•Prerequisites for QoS: Packet Matching Statistics

•Restrictions for QoS: Packet Matching Statistics

•Information About QoS: Packet Matching Statistics

•How to Use QoS: Packet Matching Statistics

•Configuration Examples for QoS: Packet Matching Statistics

•Additional References

•Feature Information for QoS: Packet Matching Statistics

Prerequisites for QoS: Packet Matching Statistics

You cannot enable or disable the QoS: Packet Matching Statistics feature if a policy map is associated with any interface on the system.

Restrictions for QoS: Packet Matching Statistics

Enabling the Qos: Packet Matching Statistics feature may increase CPU utilization on a scaled configuration. Before enabling the Qos: Packet Matching Statistics feature, weigh the benefits of the statistics information against the increased CPU utilization for your system.

Information About QoS: Packet Matching Statistics

QoS: Packet Matching Statistics Feature Overview

The QoS: Packet Matching Statistics feature allows you to define a QoS packet filter, then display the number of packets and bytes matching that filter.

To define a filter, use the class-map command with the match-any keyword, for example:

class-map match-any my_class 
   match ip precedence 4 <-------- User-defined filter 
   match qos-group 10 <-------- User-defined filter

Using this information you can do the following:

•Compare the amount of voice traffic to data traffic on a segment of your network

•Adjust bandwidth availability

•Accurately determine billing

•Troubleshoot service problems

The system collects packet matching statistics on a 10-second cycle. If there are many interfaces or sessions then the system collects statistics for about 8000 of them during each cycle. In a scaled configuration several 10-second cycles may be required to gather all statistics.

How to Use QoS: Packet Matching Statistics

Configuring QoS: Packet Matching Statistics

Prerequisites

Before enabling the QoS: Packet Matching Statistics feature, ensure no policy maps are associated with interfaces on the system. If there are, the system returns the following message:

Either a) A system RELOAD or

       b) Remove all service-policies, re-apply the change

            to the statistics, re-apply all service-policies

			is required before this command will be activated.

Before enabling the QoS: Packet Matching Statistics feature, ensure you have defined a filter is using class-map command with the match-any keyword.

Restrictions

SUMMARY STEPS

1. enable

2. configure terminal

3. platform qos match-statistics per-filter

4. end

5. show policy-map interface interface-name [vc [vpi/] vci] [dlci dlci] [input | output]

6. configure terminal

7. no platform qos match-statistics per-filter

8. end

DETAILED STEPS


	Command or Action	Purpose
Step 1	enable Example: Router> enable	Enables privileged EXEC mode. •Enter your password if prompted.
Step 2	configure terminal Example: Router# configure terminal	Enters global configuration mode.
Step 3	platform qos match-statistics per-filter Example: `Router(config)# platform qos match-statistics per-filter`	Enables the QoS: Packet Matching Statistics feature.
Step 4	end Example: Router# end	Exits configuration mode.
Step 5	show policy-map interface interface-name [vc [vpi/] vci] [dlci dlci] [input \| output] Example: Router# show policy-map interface serial4/0/0	Displays the packet statistics of all classes that are configured for all service policies either on the specified interface or subinterface or on a specific permanent virtual circuit (PVC) on the interface.
Step 6	configure terminal Example: Router# configure terminal	Enters global configuration mode.
Step 7	no platform qos match-statistics per-filter Example: `Router(config)# no platform qos match-statistics per-filter`	Disables the QoS: Packet Matching Statistics feature.
Step 8	end Example: Router# end	Exits configuration mode.

Examples

Use the show policy-map interface command to display the packet statistics of all classes that are configured for all service policies either on the specified interface or subinterface or on a specific PVC on the interface:

Router# show policy-map interface gig1/1/0

 GigabitEthernet1/1/0

  Service-policy input: pol1					! target = gig1/1/0,input

    Class-map: class1 (match-any)

      1000 packets, 40000 bytes

      5 minute offered rate 0000 bps, drop rate 0000 bps

      Match: ip precedence 1 <-------- User-defined filter

        800 packets, 32000 bytes <-------- Filter matching results

      Match: ip precedence 2 <-------- User-defined filter

        200 packets, 8000 bytes <-------- Filter matching results

      QoS Set

        ip precedence 7

          No packet marking statistics available

    Class-map: class-default (match-any)

      500 packets, 20000 bytes

      5 minute offered rate 0000 bps, drop rate 0000 bps

      Match: any <-------- User-defined filter

        500 packets, 20000 bytes <-------- Filter matching results

Troubleshooting Tips

To confirm that the QoS: Packet Matching Statistics feature is enabled, use the show platform hardware qfp active feature qos config global command. If the feature is disabled, you should see a message similar to the following:

Router# show platform hardware qfp active feature qos config global

Marker statistics are: enabled

Match per filter statistics are: enabled

Configuration Examples for QoS: Packet Matching Statistics

Example: Configuring a QoS Packet Matching Filter

This example shows how to do the following:

•Define a QoS packet matching filter

•Display the show policy-map interface command output

Router# show policy-map interface Tunnel1

  Service-policy output: DATA-OUT-PARENT

    Class-map: class-default (match-any)

      4469 packets, 4495814 bytes

      5 minute offered rate 0000 bps, drop rate 0000 bps

      Match: any <-------- User-defined filter

      Queueing

      queue limit 416 packets

      (queue depth/total drops/no-buffer drops) 0/0/0

      (pkts output/bytes output) 4469/4558380

      shape (average) cir 100000000, bc 400000, be 400000

      target shape rate 100000000

      Service-policy : DATA-OUT

        queue stats for all priority classes:

          Queueing

          queue limit 200 packets

          (queue depth/total drops/no-buffer drops) 0/0/0

          (pkts output/bytes output) 4469/4558380

        Class-map: ATM-VTI-RIP-SPK1-DATA (match-any)

          4469 packets, 4495814 bytes <-------- Filter matching results

          5 minute offered rate 0000 bps, drop rate 0000 bps

          Match: access-group 121 <-------- User-defined filter

            4469 packets, 4495814 bytes <-------- Filter matching results

            5 minute rate 0 bps

          QoS Set

            ip precedence 3

              Packets marked 4469

          Priority: 100 kbps, burst bytes 2500, b/w exceed drops: 0

Additional References

Related Topic	Document Title
Cisco IOS commands	Cisco IOS Master Commands List, All Releases
Quality of service commands	Cisco IOS Quality of Service Command Reference

Standards


Standard	Title
No new or modified standards are supported, and support for existing standards has not been modified.	—

MIBs


MIB	MIBs Link
CISCO-CLASS-BASED-QOS-MIB	To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL: http://www.cisco.com/go/mibs

RFCs


RFC	Title
No new or modified RFCs are supported, and support for existing RFCs has not been modified.	—

Technical Assistance


Description	Link
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.	http://www.cisco.com/cisco/web/support/index.html

Feature Information for QoS: Packet Matching Statistics

Table 1 lists the features in this module and provides links to specific configuration information.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Note Table 1 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Table 1 Feature Information for QoS: Packet Matching Statistics
Feature Name	Releases	Feature Information
QoS: Packet Matching Statistics	Cisco IOS XE Release 3.3S	The QoS: Packet Matching Statistics feature allows you to display the number of packets that have: •Modified headers •Been classified into a category for local router processing The following sections provide information about this feature: •Information About QoS: Packet Matching Statistics •How to Use QoS: Packet Matching Statistics The following commands were introduced or modified: platform qos match-statistics per-filter, no platform qos match-statistics per-filter, and show platform hardware qfp active feature qos config global.

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2011 Cisco Systems, Inc. All rights reserved.

Bias-Free Language

Results

Chapter: Qos: Packet Matching Statistics