Cisco SOHO 70 and Cisco 800 Series - Cisco IOS Release 12.2(8)YJ
Available Languages
Table Of Contents
Release Notes for the SOHO 70 Series Routers and the Cisco 800 Series Routers for Cisco IOS
Determining the Software Version
Upgrading to a New Software Release
New Software Features in Release 12.2(8)YJ
New Software Features in Release 12.2 T
Changing IP Addresses When Using the Cisco Easy VPN Client Feature
Open Caveats-Release 12.2(8)YJ1
Resolved Caveats- Release 12.2(8)YJ
Open Caveats- Release 12.2(8)YJ
SOHO 70 and Cisco 800 Series Routers
Obtaining Technical Assistance
Release Notes for the Cisco 800 Series Routers for Cisco IOS Release 12.2(8)YJ
Release Notes for the SOHO 70 Series Routers and the Cisco 800 Series Routers for Cisco IOS
These release notes for the SOHO 70 Series Routers and Cisco 800 Series Routers describe the enhancements provided in Cisco IOS Release 12.2(8)YJ1. These release notes are updated as needed. Use these release notes with Cross-Platform Release Notes for Cisco IOS Release 12.2 T located on Cisco.com and the Documentation CD.
For a list of the software caveats that apply to Cisco IOS Release 12.2(8)YJ1, see the "Caveats" section and Caveats for Cisco IOS Release 12.2 T. The caveats document is updated for every maintenance release and is located on Cisco.com and the Documentation CD.
Contents
These release notes discuss the following topics:
•
Obtaining Documentation and Technical Assistance, page 11
System Requirements
This section describes the system requirements for Release 12.2(8)YJ1 and includes the following sections:
•
•
Memory Requirements
Table 1 provides the memory requirements for the Cisco IOS feature sets supported by Cisco IOS Release 12.2(8)YJ1 on the and Cisco 800 Series Routers. All images are run from RAM.
Hardware Supported
Cisco IOS Release 12.2(8)YJ1 supports the following Cisco routers:
•
•
–
–
–
For detailed descriptions of new hardware features and which features are supported on each router, see the "New and Changed Information" section. For descriptions of existing hardware features and supported modules, see the hardware installation guides, configuration and command reference guides, and additional documents specific to SOHO 70 Series Routers and Cisco 800 Series Routers, which are available on Cisco.com and the Documentation CD at the following location:
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix/index.htmTable 1, Part 1 This URL is subject to change without notice. If it changes, point your web browser to CCO, and click the following path:
Cisco Product Documentation: Access Servers and Access Routers: Fixed Configuration Access Routers: <platform_name>Determining the Software Version
To determine the version of Cisco IOS software running on your Cisco router, log in to the router and enter the show version EXEC command. The following sample displays command output from a Cisco 806 router running Release 12.2(8)YJ1:
Router> show versionCisco Internetwork Operating System SoftwareIOS (tm) C806 Software (C806-SY6-MZ), Version 12.2(8)YJ, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)Synched to technology version 12.2(5.4)TUpgrading to a New Software Release
For general information about upgrading to a new software release, see Software Installation and Upgrade Procedures located at: http://www.cisco.com/warp/public/130/upgrade_index.shtml.
Feature Set Tables
The Cisco IOS software is packaged in feature sets consisting of software images—depending on the platform. Each feature set contains a specific set of Cisco IOS features. Release 12.2(8)YJ1 supports the same feature sets as Releases 12.2(8)T, but Release 12.2(8)YJ1 can include new features supported by the Cisco 800 Series Routers.
Table 2 through Table 4 list the features and feature sets supported in Cisco IOS Release 12.2(8)YJ1:
•
•
•
The tables use the following conventions:
•
•
•
Note
Table 2 Feature List by Feature Set for the Cisco 806 Series Routers
Easy VPN Client Phase II
12.2(8)YJ
Yes
No
No
New and Changed Information
The following sections list the new hardware and software features supported by Release 12.2(8)YJ1 for the SOHO 70 Series Routers and the Cisco 800 Series Routers.
New Software Features in Release 12.2(8)YJ
The following sections list the new software features supported by Cisco IOS Release 12.2(8)YJ on the and the Cisco 800 Series Routers.
Easy VPN Client Phase II
Applications for routers (and other forms of broadband access devices) that provide high-performance connections to the Internet often require the security of virtual private network (VPN) connections with a high level of access authentication and the capability to encrypt data between two endpoints. However, establishing a VPN connection between two routers can be complex, and typically requires detailed coordination between network administrators to configure the router VPN parameters.
The Cisco Easy VPN client feature eliminates much of this work by implementing the Cisco Unity Client protocol, which allows most VPN parameters to be defined at a VPN 3000 concentrator, acting as an IPSec server. After network administrators configure the IPSec server, they can create a VPN connection with minimal configuration on an IPSec client (such as a Cisco 800 series router). Note that Cisco 800 series routers are supported as Easy VPN clients of VPN 3000 IPSec servers. When the IPSec client initiates the VPN tunnel connection, the IPSec server transmits the IPSec policies to the IPSec client and creates the corresponding VPN tunnel connection.
Note
The Phase II implementation of the Cisco Easy VPN Client provides enhancements and additional capabilities to Phase I features. In Phase II, the Cisco Easy VPN Client can provide the following enhancements and feature capabilities:
•
•
•
For instructions on configuring Cisco Easy VPN client, refer to the publication Cisco Easy VPN Client Feature Phase II. This document is available on Cisco Connection Online.
Low Latency Queueing
Low Latency Queueing (LLQ) provides a low-latency, strict-priority transmit queue for voice over IP (VoIP) traffic. Strict priority queueing allows delay-sensitive data such as voice to be dequeued and sent first (before packets in other queues are dequeued), giving delay-sensitive data preferential treatment over other traffic. Refer to Software Enhancements for the Cisco 800 Routers and SOHO Routers for more information on this feature.
New Software Features in Release 12.2 T
For information regarding the features supported in Cisco IOS Release 12.2 T, refer to the Cross-Platform Release Notes and New Feature Documentation links at the following location on Cisco.com and the Documentation CD-ROM:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/index.htmThis URL is subject to change without notice. If it changes, point your web browser to Cisco.com, and click on the following path:
Service & Support: Technical Documents: Release 12.2 (from the Cisco IOS Software drop-down list)
Important Notes
The following sections contain important notes about Cisco IOS Release 12.2(8)YJ1 that can apply to SOHO 70 and Cisco 800 series routers. (Also, see the "Caveats" section.)
Changing IP Addresses When Using the Cisco Easy VPN Client Feature
In Cisco 800 series routers, the Ethernet 0 LAN interface defaults to the primary IP address of 10.10.10.0 in a private network. If you need to change this IP address to match the local network configuration, you can use the command ip address or the Cisco Router Web Setup (CRWS) web interface.
Using the CRWS interface to change the IP address preserves the existing IP address as the primary address of the interface and assigns the new IP address as the secondary address on the interface. This CRWS interface functionality maintains (does not break) the existing connection between the PC web browser and the Cisco 800 series router and thereby does not interfere with normal router operations for most configurations.
Because of this behavior, the Cisco Easy VPN client feature assumes that if a secondary IP address exists on the Ethernet 0 interface, the secondary address should be used as the IP address for the inside interface for the NAT/PAT configuration. If no secondary address exists, the primary IP address will be used for the inside interface address, as is normally done on other platforms. If this behavior is not desired, use the ip address CLI command instead of the CRWS web interface to change the interface address.
Caveats
Caveats describe unexpected behavior in Cisco IOS software releases. Severity 1 caveats are the most serious caveats, severity 2 caveats are less serious, and severity 3 caveats are the least serious of these three severity levels.
Caveats in Cisco IOS Releases 12.2 and 12.2 T are also in Cisco IOS Release 12.2(8)YJ1. For information on caveats in Cisco IOS Release 12.2, see Caveats for Cisco IOS Release 12.2. For information on caveats in Cisco IOS Release 12.2 T, see Caveats for Cisco IOS Release 12.2 T. These two documents list severity 1 and 2 caveats and are located on CCO and the Documentation CD-ROM.
Note
Open Caveats-Release 12.2(8)YJ1
This section describes unexpected behavior in Release 12.2(8)YJ1.
CSCin11017
When acting as a PPPoE client, the Cisco 806 router a crashes after the DDR idle timeout expires. This problem might be seen only in lab scenarios.
CSCin11192
Dial on Demand Routing (DDR) is triggered by traffic that enters the Cisco 806 router from the WAN interface.Generally, one expects DDR to be triggered only by traffic that enters the router from the LAN interface.
Workaround: Access lists can be configured to block traffic on the WAN interface.
CSCin11465
If the access list at the remote end of a split tunnel is configured to have two entries with the same source address, an Easy VPN client, such as a Cisco 806 router, will try to install the same address twice and will alter the NAT configuration in such a way that NAT translation will not work correctly. This is normal behavior. However, NAT translation seems to work correctly on Cisco 806 routers operating in this type of split tunnel environment.
CSCin11727
With Point-to-Point Protocol over ATM encapsulation, when the permanent virtual circuit (PVC) is removed and configured again, the virtual access interface doesn't come up causing the ping between the UUT and the remote to fail.
Workaround: Save the configuration before you remove the PVC, and reload the router if this problem occurs.
CSCin12124
The HTTP probe does not show the default values.
CSCdw37744
The firewall audit trail test for the trivial file tranfer protocol (tftp) fails.
CSCin08502
tftp fails with NAT overload configured when the unit under test listens for tftp traffic on a non-standard port.
CSCin08629
The rttMonEchoAdminCache variable does not show the correct default value.
CSCin09771
The rttMonApplSupportedRttTypesValid.10 is not supported.
CSCin12882
The udpLocalAddress and udpLocalPort objects of the UDP MIB are not populated.
Resolved Caveats- Release 12.2(8)YJ
This section describes unexpected behavior that is fixed in Release 12.2(8)YJ.
CSCin10864
The Easy VPN 806 client crashes when unconfiguring the Dialer interface. This problem has been fixed in this release.
CSCin12086
The router crashes while reconfiguring service policy on the Dialer interface. This problem has been fixed in this release.
CSCin10852
The running configuration does not show if the maximum ssh timeout value is configured. This problem has been fixed in this release.
CSCin11722
The router crashes while configuring PPP encapsulation on the dialer interface. This problem has been fixed in this release.
CSCdw37744
The firewall audit trail test for tftp fails. This problem has been fixed in this release.
Open Caveats- Release 12.2(8)YJ
CSCin08629
The rttMonEchoAdminCache variable doe not show.
CSCin08637
The rttMonEchoAdminPktDataRequestSize shows.
CSCin08536
The DNS probe fails due to a timeout occuring when the domain name is being resolved.
CSCin08549
The rttMonCtrlAdminTimeout value does not show.
CSCin08502
tftp fails with NAT overload when uut listens tftp on a non-standard port.
CSCin12124
The http probe does not show the default values.
CSCin12023
The Cisco 827 router crashes at vtemplate_nvgen while configuring ip add on virtual-t.
CSCin11017
The 806 router client crashes after the idle timeout expires for DDR.
CSCin11373
Ping is not successful when aal5mux ppp encapsulation is used.
CSCin11192
DDR is always triggered when traffic is in opposite direction.
CSCin11465
Easy VPN:split tunneling extended ACL issue.
CSCin11727
Recreating the PVC does not bring the virtual access interface up.
CSCin09643
The 806uut is unable to pass ipsec traffic when NAT is enabled.
CSCin09365
The DHCP is not activated on the interface even when the interface is up.
Related Documentation
The following sections describe the documentation available for the SOHO 70 and Cisco 800 series routers. Typically, these documents consist of hardware and software installation guides, Cisco IOS configuration and command references, system error messages, feature modules, and other documents.
Documentation is available as printed manuals or electronic documents, except for feature modules and the Cisco IOS release notes, which are available online on Cisco.com and the Documentation CD-ROM.
Use these release notes with the documents listed in the following sections:
Release-Specific Documents
The following documents are specific to Release 12.2 and apply to Release 12.2(8)YJ1. They are located on Cisco.com and the Documentation CD-ROM (under the heading Service & Support):
•
Technical Documents: Cisco IOS Software: Release 12.2: Release Notes: Cisco 800 Series Routers: Cisco 800 Series - Release Notes for Release 12.2(8)YJ
•
Technical Documents: Cisco IOS Software: Release 12.2: Release Notes: Cisco IOS Release 12.2 T
•
Technical Documents: Product Bulletins
•
Technical Documents: Cisco IOS Software: Release 12.2: Caveats
Note
Platform-Specific Documents
Hardware installation guides, configuration and command reference guides, and additional documents are available for the SOHO 70 and Cisco 800 series routers on Cisco.com and the Documentation CD-ROM.
SOHO 70 and Cisco 800 Series Routers
Documentation specific to the SOHO 70 Series Routers and Cisco 800 Series Routers is available on Cisco.com and the Documentation CD at the following location:
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix/index.htm
This URL is subject to change without notice. If it changes, point your web browser to CCO, and click the following path:
Cisco Product Documentation: Access Servers and Access Routers: Fixed Configuration Access Routers: Cisco 1700 Series Routers: <platform_name>
Software Configuration
The document Cisco Router Web Setup User Guide is available for the SOHO 70 series routers at the following location:
http://www.cisco.com/univercd/cc/td/doc/clckstrt/crws/ugcrws30.htm
This URL is subject to change without notice. If it changes, point your web browser to Cisco.com or the Documentation CD, and click the following path:
Technical Documents: Router Configuration Tools: Cisco Router Web Setup
Obtaining Documentation
These sections explain how to obtain documentation from Cisco Systems.
World Wide Web
You can access the most current Cisco documentation on the World Wide Web at this URL:
Translated documentation is available at this URL:
http://www.cisco.com/public/countries_languages.shtml
Documentation CD-ROM
Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which is shipped with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or through an annual subscription.
Ordering Documentation
You can order Cisco documentation in these ways:
•
http://www.cisco.com/web/ordering/root/index.html
•
http://www.cisco.com/go/subscription
•
Documentation Feedback
You can submit comments electronically on Cisco.com. In the Cisco Documentation home page, click the Fax or Email option in the "Leave Feedback" section at the bottom of the page.
You can e-mail your comments to bug-doc@cisco.com.
You can submit your comments by mail by using the response card behind the front cover of your document or by writing to the following address:
Cisco Systems
Attn: Document Resource Connection
170 West Tasman Drive
San Jose, CA 95134-9883We appreciate your comments.
Obtaining Technical Assistance
Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain online documentation, troubleshooting tips, and sample configurations from online tools by using the Cisco Technical Assistance Center (TAC) Web Site. Cisco.com registered users have complete access to the technical support resources on the Cisco TAC Web Site.
Cisco.com
Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information, networking solutions, services, programs, and resources at any time, from anywhere in the world.
Cisco.com is a highly integrated Internet application and a powerful, easy-to-use tool that provides a broad range of features and services to help you with these tasks:
•
•
•
•
•
If you want to obtain customized information and service, you can self-register on Cisco.com. To access Cisco.com, go to this URL:
Technical Assistance Center
The Cisco Technical Assistance Center (TAC) is available to all customers who need technical assistance with a Cisco product, technology, or solution. Two levels of support are available: the Cisco TAC Web Site and the Cisco TAC Escalation Center.
Cisco TAC inquiries are categorized according to the urgency of the issue:
•
•
•
•
The Cisco TAC resource that you choose is based on the priority of the problem and the conditions of service contracts, when applicable.
Cisco TAC Web Site
You can use the Cisco TAC Web Site to resolve P3 and P4 issues yourself, saving both cost and time. The site provides around-the-clock access to online tools, knowledge bases, and software. To access the Cisco TAC Web Site, go to this URL:
All customers, partners, and resellers who have a valid Cisco service contract have complete access to the technical support resources on the Cisco TAC Web Site. The Cisco TAC Web Site requires a Cisco.com login ID and password. If you have a valid service contract but do not have a login ID or password, go to this URL to register:
http://www.cisco.com/register/
If you are a Cisco.com registered user, and you cannot resolve your technical issues by using the Cisco TAC Web Site, you can open a case online by using the TAC Case Open tool at this URL:
http://www.cisco.com/tac/caseopen
If you have Internet access, we recommend that you open P3 and P4 cases through the Cisco TAC Web Site.
Cisco TAC Escalation Center
The Cisco TAC Escalation Center addresses priority level 1 or priority level 2 issues. These classifications are assigned when severe network degradation significantly impacts business operations. When you contact the TAC Escalation Center with a P1 or P2 problem, a Cisco TAC engineer automatically opens a case.
To obtain a directory of toll-free Cisco TAC telephone numbers for your country, go to this URL:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml
Before calling, please check with your network operations center to determine the level of Cisco support services to which your company is entitled: for example, SMARTnet, SMARTnet Onsite, or Network Supported Accounts (NSA). When you call the center, please have available your service agreement number and your product serial number.
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
Copyright © 2002, Cisco Systems, Inc.
All rights reserved.Release Notes for the Cisco 800 Series Routers for Cisco IOS Release 12.2(8)YJ
July 15, 2002
These release notes for the Cisco 800 Series Routers describe the enhancements provided in Cisco IOS Release 12.2(8)YJ1. These release notes are updated as needed. Use these release notes with Cross-Platform Release Notes for Cisco IOS Release 12.2 T located on Cisco.com and the Documentation CD.
For a list of the software caveats that apply to Cisco IOS Release 12.2(8)YJ1, see the "Caveats" section and Caveats for Cisco IOS Release 12.2 T. The caveats document is updated for every maintenance release and is located on Cisco.com and the Documentation CD.
Contents
These release notes discuss the following topics:
Feedback