Worldwide [change] |Account |Register |About Cisco
Guest

Hierarchical Navigation

Cisco IOS Software Releases 12.1 Special and Early Deployments

1-Port ADSL WAN Interface Card Configuration

Downloads

Table Of Contents

1-Port ADSL WAN Interface Card

Feature Overview

Benefits

Restrictions

Related Documents

Supported Platforms

Configuring the ADSL WAN Interface Card

Configuring the ADSL port on the ADSL WAN Interface Card

Verifying ATM Configuration

Configuration Examples

VoATM over AAL2 on the ATM Interface

VoATM over AAL5 on the ATM Interface

Command Reference

dsl operating-mode

show dsl interface atm

Debug Commands

show diag wic-slot-num


1-Port ADSL WAN Interface Card

This feature module describes the 1-port Asymmetric Digital Subscriber Line Wide Area Network (ADSL WAN) Interface Card feature for Cisco 1700 series, Cisco 2600 series and Cisco 3600 series routers. It describes the benefits of the new feature, supported platforms, configuration, related documents, and provides command reference information.

This document includes the following sections:

•Feature Overview

•Supported Platforms

•Configuring the ADSL WAN Interface Card

•Configuration Examples

•Command Reference

•Debug Commands

Feature Overview

The ADSL WAN interface card is a 1-port WAN interface card (WIC) for the Cisco 1700 series, Cisco 2600 series and Cisco 3600 series routers. The card provides asymmetric digital subscriber line (ADSL) high-speed digital data transfer between a single customer premises equipment (CPE) subscriber and the central office.

The ADSL WIC is compatible with the Alcatel Digital Subscriber Loop Access Multiplexer (DSLAM) and the Cisco 6130, Cisco 6160, and Cisco 6260 DSLAMs with Flexi-line cards. It supports Asynchronous Transfer Mode (ATM) Adaptation Layer 2 (AAL2) and AAL5 for the 2600/3600 series platforms, and AAL5 only for the 1700, for both voice and data service.

The general topology is shown in Figure 1.

Figure 1 General Topology for ADSL WIC

Note ADSL is a last-mile access technology, which has an asymmetrical data rate running over a single copper wire pair.

Benefits

•Enables business class broadband service with voice integration, scalable performance, flexibility, and security.

•Aggregates both ADSL and other transport options into a single box.

•Provides both POTS and ADSL high-speed digital data transmissions between the customer premise equipment (CPE) and the central office (CO).

•Supports ITU G.992.1 (or G.DMT, which specifies full-rate ADSL).

•Supports and complies with ANSI T1.413 issue 2, and ITU G.992.1 (G.DMT for full-rate ADSL).

•Supports ATM AAL2 and AAL5 services on the 2600/3600 series platforms and AAL5 services on the 1700 series platform and applications (including VoATM voice), ATM class of service (variable bit rate-nonreal time [VBR-NRT], variable bit rate-real time [VBR-rt], and unspecified bit rate [UBR]) and up to 23 virtual circuits on a WIC.

•Provides ATM traffic management to enable service providers to manage their core ATM network infrastructures.

Restrictions

•The ADSL WAN interface card does not support dual latency. When the ADSL link is intended to support both voice and data traffic simultaneously, the link should be configured for either all fast-path data or all interleave data with an interleave depth of zero to insure that latency is minimized. In addition, the total supported data rate must be reduced to adjust for the reduced coding gain, which is usually present with high-latency traffic.

•The ADSL WAN interface card does not support ABR class of service (CoS).

•For the Cisco 2600 series routers, the ADSL WAN interface card should only be inserted into on-board WIC slots or 2W network modules. This card will not function properly in older network modules.

•For the Cisco 3600 series routers, the ADSL WAN interface card should only be inserted into on-board WIC slots or 2W, 1FE2W, 2FE2W, or 1FE1R2W network modules. This card will not function properly in older network modules.

•When using AAL2, analog voice is not supported. Voice calls should come through a digital voice card, such as the NM-HDV.

•VoATM is supported in both AAL2 and AAL5 modes on the 2600 and 3600 series. VoATM AAL5 is supported on the 1700 series.

•VoATM AAL2 and AAL5 are only supported if voice and data use separate PVCs.

•VoATM AAL2 supports digital voice only (T1/E1), while VoATM AAL5 supports both analog and digital voice.

•VoIP is not supported until a later release unless the ADSL WIC carries only voice traffic (with no data). The QoS features necessary for VoIP and data sharing the same PVC, or different PVCs on the same interface, are not supported yet. These features include LLQ, LFI and tx-ring tuning.

Related Documents

For more information about voice configuration, see the following Cisco IOS Release 12.1 guides:

•Voice, Video, and Home Applications Configuration Guide

•Voice, Video, and Home Applications Command Reference

The following configuration guides describe the configuration of IP and ATM:

•For more information about configuring IP, see the Cisco IOS Release 12.1 Network Protocols Configuration Guide, Part 1.

•For more information about configuring ATM, see "Configuring ATM"  in the Cisco IOS Release 12.1 Wide-Area Networking Configuration Guide.

The following online feature documentation and installation guides describe the configuration and installation of hardware components:

•For information about installing Cisco 1700 series hardware, see the documents listed at the following location: http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/1700/index.htm

•For information about installing Cisco 2600 series hardware, see the documents listed at the following location: http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis2600/index.htm

•For information about installing Cisco 3600 series hardware, see the documents listed at the following location: http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis3600/index.htm

Supported Platforms

This feature is supported on the following platforms:

•Cisco 1700 series routers

•Cisco 2600 series routers

•Cisco 3600 series routers

Configuring the ADSL WAN Interface Card

This section contains the following information:

•Configuring the ADSL port on the ADSL WAN Interface Card

•Verifying ATM Configuration

Features used on the ADSL WAN interface card must also be configured on the DSLAM. See the documentation for the specific DSLAM for information about configuring features.

Configuring the ADSL port on the ADSL WAN Interface Card

To configure an ADSL port on the ADSL WAN interface card, complete the following steps:

 
Command
Purpose

Step 1 

router> configure terminal

Enter global configuration mode.

Step 2 

router(config)# interface atm slot/port

Enter ATM configuration mode for the ATM interface in the specified slot and port.

Step 3 

router(config-if)# ip address IP-address

Assign an IP address to the ADSL ATM interface.

Step 4 

router(config-if)# pvc [name] vpi/vci

Enters atm-virtual-circuit (interface-atm-vc) configuration mode, and configures a new ATM PVC by assigning a name (optional) and VPI/VCI numbers.

The default traffic shaping is UBR; the default encapsulation is AAL5+LLC/SNAP.

Step 5 

router(config-if-vc)# protocol ip IP-address

(Optional) Enable IP connectivity and create a point-to-point IP address for the VC.

Step 6 

router(config-if-vc)# vbr-rt peak-rate average-rate burst

(Optional) Configure the PVC for real-time variable bit rate (VBR) traffic shaping.

•Peak rate = peak information rate (PIR)

•Average rate = average information rate (AIR)

•Burst = burst size in cells

Step 7 

router(config-if-vc)# encapsulation {aal2 | aal5ciscoppp | aal5mux | aal5nlpid | aal5snap}

(Optional) Configure the ATM adaptation layer (AAL) and encapsulation type.

•aal2 for AAL2

•aal5ciscoppp for Cisco PPP over AAL5

•aal5mux for AAL5+MUX

•aal5nlpid for AAL5+NLPID

•aal5snap for AAL5+LLC/SNAP (the default)

Step 8 

router(config-if-vc)# exit

Exit from interface-ATM-VC configuration mode.

Step 9  

router(config-if)# dsl 
operating-mode {ansi-dmt | auto 
itu-dmt | splitterless}

Configure the ADSL interface to operate in a specified mode:

•ansi-dmt—ANSI full rate mode per T1.413 (ITU G dmt Issue 1)

•auto—Automatic detection mode

•itu-dmt—ITU full rate mode (ITU G dmt Issue 1)

•splitterless—G.lite mode per ITU g.992.2

Step 10 

router(config-if)# no shutdown

Activate the ATM interface.

Step 11 

router(config-if)# exit

Exit from ATM interface configuration mode.

Step 12 

router(config-if)# exit

Exit from ATM interface configuration mode.

Step 13 

router(config)# exit

Exit from global configuration mode.

Step 14 

router# show interface atm 1/0

Verify the ATM interface configuration.

Verifying ATM Configuration

Use the following commands to verify configuration:

•Use show running-config to verify current configuration and to view the status for all controllers.

•Use show controllers atm slot/port to view ATM controller statistics.

•Use show atm vc to verify the PVC status. Make sure that active PVCs are up.

•Use debug atm events to help identify ATM related events as they are generated. Use debug atm errors to indicate what interfaces are having trouble.

•Use show ip route to identify an entry for the ATM interface you configured and to show that an entry for the ATM slot/port you configured it.

•Use show atm map to display the configured list of ATM static maps to remote hosts on an ATM network.

•Use show interface atm slot/port to view the status of ATM interface. Make sure ATM slot/port and line protocol is up, as shown in the following example: 


Router#sh int atm1/0

ATM1/0 is up, line protocol is up 

  Hardware is DSLSAR (with Alcatel ADSL Module)

  MTU 4470 bytes, sub MTU 4470, BW 800 Kbit, DLY 2560 usec, 

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ATM, loopback not set

  Keepalive not supported 

  Encapsulation(s):AAL5 AAL2, PVC mode

  24 maximum active VCs, 256 VCs per VP, 2 current VCCs

  VC idle disconnect time:300 seconds

  Last input never, output 00:00:01, output hang never

  Last clearing of "show interface" counters 03:16:00

  Queueing strategy:fifo

  Output queue 0/40, 0 drops; input queue 0/75, 0 drops

  30 second input rate 0 bits/sec, 0 packets/sec

  30 second output rate 0 bits/sec, 0 packets/sec

     2527 packets input, 57116 bytes, 0 no buffer

     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

     10798 packets output, 892801 bytes, 0 underruns

     0 output errors, 0 collisions, 0 interface resets

     0 output buffer failures, 0 output buffers swapped out



Router#sh atm vc

            VCD /                                      Peak  Avg/Min Burst

Interface   Name       VPI   VCI  Type   Encaps   SC   Kbps   Kbps   Cells  Sts

1/0.3      2            9    36   PVC    MUX      UBR     800                UP

1/0.2      1            9    37   PVC    SNAP     UBR     800                UP



Router#sh controllers atm 1/0

Interface ATM1/0 is up

  Hardware is DSLSAR (with Alcatel ADSL Module)

IDB:    62586758  Instance:6258E054  reg_dslsar:3C810000  wic_regs:3C810080

PHY Inst:62588490  Ser0Inst:62573074  Ser1Inst: 6257CBD8  us_bwidth:800     

Slot:   1         Unit:    1         Subunit:  0         pkt Size:4496    

VCperVP:256       max_vp:  256       max_vc:   65536     total vc:2       

rct_size:65536     vpivcibit:16        connTblVCI:8         vpi_bits:8       

vpvc_sel:3         enabled: 0         throttled:0       


WIC    Register   Value      Notes

---------------   ---------- ----------

FPGA Dev ID (LB)  0x44       'D'

FPGA Dev ID (UB)  0x53       'S'

FPGA Revision     0x99       

WIC Config Reg    0x45       WIC / VIC select = WIC; 

                             CTRLE addr bit 8 = 1; 

                             OK LED on; 

                             LOOPBACK LED off; 

                             CD LED on; 

WIC Config Reg2   0x07       Gen bus error on bad ADSL access

Int 0 Enable Reg  0x03       ADSL normal interrupt enabled

                             ADSL error interrupt enabled

Configuration Examples

The following examples are presented:

•VoATM over AAL2 on the ATM Interface

•VoATM over AAL5 on the ATM Interface

VoATM over AAL2 on the ATM Interface

The following sample shows a Cisco 2600 series router configured for VoATM over AAL2 on the ATM interface with an ADSL card: 

version 12.1

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname host1

!

memory-size iomem 10

voice-card 1

!

ip subnet-zero

ip host host2 225.255.255.255

!

no mgcp timer receive-rtcp

call rsvp-sync

!

!

controller T1 1/0

 framing esf

 linecode b8zs

 ds0-group 0 timeslots 1 type e&m-wink-start

 ds0-group 1 timeslots 2 type e&m-wink-start

.

.

.

ds0-group 23 timeslots 24 type e&m-wink-start

!

controller T1 1/1

 framing esf

 linecode b8zs

!

interface Ethernet0/0

 ip address 1.6.46.119 255.255.255.0

 half-duplex

 no cdp enable

!

interface Serial0/0

 no ip address

 shutdown

!

interface ATM0/1

 ip address 10.1.1.1 255.0.0.0

 load-interval 30

 atm vc-per-vp 256

 no atm ilmi-keepalive

 pvc 10/100 

  vbr-rt 672 672 512

  encapsulation aal2

 !

 pvc 10/200 

  protocol ip 10.1.1.2 broadcast

  encapsulation aal5snap

 !

 dsl operating-mode ansi-dmt

 no fair-queue

!

interface Ethernet0/1

 no ip address

 shutdown

!

ip classless

ip route 223.255.254.254 255.255.255.255 Ethernet0/0

no ip http server

!

!

snmp-server engineID local 000000090200003080477F20

snmp-server manager

!

voice-port 1/0:0

 local-alerting

 timeouts wait-release 3

 connection trunk 3001 

!

voice-port 1/0:1

 local-alerting

 timeouts wait-release 3

 connection trunk 3002 

.

.

.

voice-port 1/0:23

 local-alerting

 timeouts wait-release 3

 connection trunk 3024 

 shutdown

!

dial-peer cor custom

!

dial-peer voice 3001 voatm

 destination-pattern 3001

 called-number 4001

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 31

 codec aal2-profile ITUT 1 g711ulaw

 no vad

!

dial-peer voice 3002 voatm

 destination-pattern 3002

 called-number 4002

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 32

 codec aal2-profile custom 100 g726r32

 no vad

!

dial-peer voice 3003 voatm

 destination-pattern 3003

 called-number 4003

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 33

 codec aal2-profile ITUT 7 g729abr8

 no vad

.

.

.

dial-peer voice 3024 voatm

 destination-pattern 3024

 called-number 3024

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 54

 codec aal2-profile ITUT 7 g729abr8

 no vad

!

dial-peer voice 1 pots

 destination-pattern 4001

 port 1/0:0

!

dial-peer voice 2 pots

 destination-pattern 4002

 port 1/0:1

.

.

.

dial-peer voice 24 pots

 destination-pattern 4024

 port 1/0:23

!

!

line con 0

 exec-timeout 0 0

 transport input none

line aux 0

line vty 0 4

 login

!

no scheduler allocate

end

VoATM over AAL5 on the ATM Interface

The following sample shows a Cisco 2600 series router configured for VoATM over AAL5 on the ATM interface with an ADSL card. 

version 12.1

no service single-slot-reload-enable

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname u2621

!

no logging buffered

no logging buffered

logging rate-limit console 10 except errors

!

memory-size iomem 15

voice-card 1

!

ip subnet-zero

!

no ip finger

no ip domain-lookup

!

no mgcp timer receive-rtcp

call rsvp-sync

!

controller T1 1/0

 framing esf

 linecode b8zs

 ds0-group 0 timeslots 1-24 type e&m-wink-start

!

controller T1 1/1

!

!

interface ATM0/0

 ip address 12.0.0.1 255.0.0.0

 load-interval 30

 atm vc-per-vp 256

 no atm ilmi-keepalive

 dsl operating-mode auto

 no fair-queue

!

!

interface FastEthernet0/0

 ip address 1.7.73.1 255.255.255.0

 duplex auto

 speed auto

!

!

interface FastEthernet0/1

 ip address 192.168.2.1 255.255.255.0

 load-interval 30

 duplex auto

 speed auto

!

ip classless

ip route 223.255.254.0 255.255.255.0 FastEthernet0/0

no ip http server

!

!

snmp-server engineID local 0000000902000002163DB260

snmp-server packetsize 4096

snmp-server manager

!

voice-port 1/0:0

!

dial-peer cor custom

!

!

dial-peer voice 5 pots

 destination-pattern 777...

 port 1/0:0

 prefix 777

! 

! 

dial-peer voice 100 voatm

 destination-pattern 888....

 session target atm0/0 pvc 0/72

!

!

line con 0

 exec-timeout 0 0

 transport input none

line aux 0

line vty 0 4

 login

!

end

Command Reference

This section documents the new or changed Cisco IOS commands for configuring the ADSL WAN Interface Card feature. All other commands used to configure the ADSL WAN Interface Card feature are documented in the following publications:

•The "Configuring ATM" section of the Cisco IOS Wide-Area Networking Configuration Guide

•The "ATM Commands" section of the Cisco IOS Wide-Area Networking Command Reference

Reference information is provided below for configuring the following Cisco IOS on the Cisco 1700 series, Cisco 2600 series and Cisco 3600 series routers:

•dsl operating-mode

•show dsl interface atm

•show diag wic-slot-num

dsl operating-mode

Caution This command is for testing or lab environments only. Using a configuration other than the default configuration for the DSL operating mode can lead to unpredictable behavior on the ADSL line.

To modify the operating mode of the digital subscriber line for an ATM interface, use the Interface mode dsl operating-mode command.

dsl operating-mode { auto | ansi-dmt | itu-dmt | splitterless }

no dsl operating-mode { auto | ansi-dmt | itu-dmt | splitterless}

Syntax Description

Command Elements
Description

auto

Configure the ADSL line after auto-negotiating with the DSLAM located at the Central Office.

ansi-dmt

Configure the ADSL line to train in the ANSI T1.413 Issue 2 mode.

itu-dmt

Configure the ADSL line to train in the G.992.1 mode.

splitterless

Configure the ADSL line to train in the G.lite mode.


Defaults

None.

Command Modes

Interface

Command History

Release
Modification

Cisco IOS Release 12.1(3)XJ

The command dsl operating-mode was introduced on the Cisco 1700 series routers.

Cisco IOS Release 12.1(5)YB

This command was introduced on the Cisco 1700 series, Cisco 2600 series and Cisco 3600 series routers.


Usage Guidelines

This configuration command applies to a specific ATM interface. The interface to which it applies must be specified before using the command.

Examples 

router# conf t 

Enter configuration commands, one per line. End with CNTL/Z. 

router(config)# int atm 0/0 

router(config-if)# dsl operating-mode auto 

router(config-if)# end 

router#

Related Commands

Command
Description

show dsl interface atm

Show all of the ADSL-specific information for a specified ATM interface.

show diag wic-slot-num

Specify detailed diagnostic options for displaying the memory on an ADSL-WIC and the ADSL line training log.


show dsl interface atm

To show the ADSL-specific information for a specified ATM interface, use the Exec mode show dsl interface atm command.

show dsl interface atm slot/port

Syntax Description

Command Elements
Description

slot/port

Choose the slot and port number to be connected.


Defaults

Exec.

Command History

Release
Modification

Cisco IOS Release 12.1(3)XJ

The command show dsl interface atm was introduced on the Cisco 1700 series routers.

Cisco IOS Release 12.1(5)YB

This command was introduced on the Cisco 1700 series, Cisco 2600 series and Cisco 3600 series routers.


Usage Guidelines

The output from this command appears the same as the output from the command show controller atm 0 | b chipset on the Cisco 1400 series routers.

Examples

This command shows all of the ADSL specific information for the ATM interface requested. 

router# show dsl int atm0/1

Alcatel 20150 chipset information

                ATU-R (DS)                      ATU-C (US)

Modem Status:    Showtime (DMTDSL_SHOWTIME)

DSL Mode:        ITU G.992.1 (G.DMT)

ITU STD NUM:     0x01                            0x1 

Vendor ID:       'ALCB'                          'ALCB'

Vendor Specific: 0x0000                          0x0000

Vendor Country:  0x00                            0x0F

Capacity Used:   85%                             98%

Noise Margin:    13.5 dB                          7.0 dB

Output Power:     9.5 dBm                        12.0 dBm

Attenuation:      1.5 dB                          3.5 dB

Defect Status:   None                            None 

Last Fail Code:  None

Selftest Result: 0x00

Subfunction:     0x15

Interrupts:      5940 (0 spurious)

PHY Access Err:  0

Activations:     1

SW Version:      3.670

FW Version:      0x1A04



                 Interleave             Fast    Interleave              Fast

Speed (kbps):             0             8128             0               864

Reed-Solomon EC:          0                0             0                 0

CRC Errors:               0                0             0                 7

Header Errors:            0                0             0                 2

Bit Errors:               0                0

BER Valid sec:            0                0

BER Invalid sec:          0                0



DMT Bits Per Bin

00: 0 0 0 0 0 0 0 7 6 7 9 A B C C C

10: C C C C C C B B B B A 9 A 9 0 0

20: 0 0 0 0 0 0 2 2 3 4 4 5 6 6 7 7

30: 7 8 8 8 9 9 9 A A A A A A B B B

40: B B B B B B B B B B B A B B B B

50: B B B B B B B B B B B B 2 B B B

60: B B B B B B B B B B B B B B B B

70: B B B B B B B B B B B B B B B B

80: B B B B B B B B B B B B B B B B

90: B B B B B B B B B B B B B B B B

A0: B B B B B B B B B B B B B B B B

B0: B B B B B B B B B B B B A B A A

C0: A A A A A A A A A A A A A A A A

D0: A A A A A A A A A A A 9 9 9 9 9

E0: 9 9 9 9 9 9 9 9 9 9 9 9 8 8 8 8

F0: 8 8 8 8 8 8 7 7 7 7 6 6 5 5 4 4

Related Commands

Command
Description

dsl operating-mode

Modify the operating mode of the digital subscriber line for an ATM interface.

show diag wic-slot-num

Specify detailed diagnostic options for displaying the memory on an ADSL-WIC and the ADSL line training log.


Debug Commands

This section documents the new debug commands related to the ADSL WAN Interface Card on Cisco 1700 series, Cisco 2600 series and Cisco 3600 series routers.

show diag wic-slot-num

To specify detailed diagnostic options for displaying the memory on an ADSL-WIC and the ADSL line training log, use the Exec mode show diag command.

show diag

Syntax Description

Command Elements
Description

wic-slot-num

WIC slot number 0 or 1.

mem start_address end_address

Display the contents of ADSL-WIC memory.

log

Display the ADSL line training log.


Command Modes

Exec.

Command History

Release
Modification

Cisco IOS Release 12.1(3)XJ

The command show diag was modified to become the command show diag wic-slot-num on the Cisco 1700 series routers, for use with ADSL.

Cisco IOS Release 12.1(5)YB

This command was modified on the Cisco 1700 series, Cisco 2600 series and Cisco 3600 series routers.


Examples

The following examples show the use of the show diag wic-slot-num command on Cisco 1700 series routers. 

router# show diag 

Slot 0:

        C2621 2FE Mainboard Port adapter, 4 ports

        Port adapter is analyzed 

        Port adapter insertion time unknown

        EEPROM contents at hardware discovery:

        Hardware Revision        :1.2

        PCB Serial Number        :JAB041709PU (3653006624)

        Part Number              :73-3200-07

        RMA History              :00

        RMA Number               :0-0-0-0

        Board Revision           :B0

        Deviation Number         :0-22418

        EEPROM format version 4

        EEPROM contents (hex):

          0x00:04 FF 40 00 A2 41 01 02 C1 18 4A 41 42 30 34 31

          0x10:37 30 39 50 55 20 28 33 36 35 33 30 30 36 36 32

          0x20:34 29 82 49 0C 80 07 04 00 81 00 00 00 00 42 42

          0x30:30 80 00 00 57 92 FF FF FF FF FF FF FF FF FF FF

          0x40:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x50:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF


        WIC Slot 0:

        DSL SAR (ADSL)


        Hardware Revision        :1.0

        Part Number              :73-4771-05

        Board Revision           :A0

        Deviation Number         :0-0

        Fab Version              :02

        PCB Serial Number        :JAB0437

        IDPROM FIELD FORMAT ERROR, index 0x22

        EEPROM format version 4

        EEPROM contents (hex):

          0x00:04 FF 40 00 2E 41 01 00 82 49 12 A3 05 42 41 30

          0x10:80 00 00 00 00 02 02 C1 8B 4A 41 42 30 34 33 37

          0x20:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

          0x30:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

          0x40:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

          0x50:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

          0x60:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

          0x70:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00


        WIC Slot 1:

        DSL SAR (ADSL)

        Hardware Revision        :1.0

        Part Number              :73-4771-05

        Board Revision           :A0

        Deviation Number         :0-0

        Fab Version              :02

        PCB Serial Number        :JAB0437

        IDPROM FIELD FORMAT ERROR, index 0x22

        EEPROM format version 4

        EEPROM contents (hex):

          0x00:04 FF 40 00 2E 41 01 00 82 49 12 A3 05 42 41 30

          0x10:80 00 00 00 00 02 02 C1 8B 4A 41 42 30 34 33 37

          0x20:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

          0x30:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

          0x40:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

          0x50:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

          0x60:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

          0x70:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00


Slot 1:

        High Density Voice Port adapter

        Port adapter is analyzed 

        Port adapter insertion time unknown

        EEPROM contents at hardware discovery:

        Hardware Revision        :1.0

        Top Assy. Part Number    :800-03567-01

        Board Revision           :A0

        Deviation Number         :0-0

        Fab Version              :02

        PCB Serial Number        :JAB033500T5

        RMA Test History         :00

        RMA Number               :0-0-0-0

        RMA History              :00

        EEPROM format version 4

        EEPROM contents (hex):

          0x00:04 FF 40 00 CC 41 01 00 C0 46 03 20 00 0D EF 01

          0x10:42 41 30 80 00 00 00 00 02 02 C1 8B 4A 41 42 30

          0x20:33 33 35 30 30 54 35 03 00 81 00 00 00 00 04 00

          0x30:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x40:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x50:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF


        VIC Slot 0:

        T1 (2 Port) Multi-Flex Trunk (Drop&Insert) WAN Daughter Card

        Hardware revision 1.0           Board revision B0

        Serial number     17216762      Part number    800-04614-01

        Test history      0x0           RMA number     00-00-00

        Connector type    PCI

        EEPROM format version 1

        EEPROM contents (hex):

          0x20:01 24 01 00 01 06 B4 FA 50 12 06 01 00 00 00 00

          0x30:58 00 00 00 99 11 15 00 FF FF FF FF FF FF FF FF


        HDV firmware:Compiled Wed 04-Oct-00 19:39 by mani

        HDV memory size 524280 heap free 211849

Command
Description

dsl operating-mode

Modify the operating mode of the digital subscriber line for an ATM interface.

show dsl interface atm

Show all of the ADSL-specific information for a specified ATM interface.