Table 2-1 Cisco RF Gateway 10 Commands by Function
Command Name
|
Command Description
|
Reference
|
Bundled Image Upgrade
|
show cable image-upgrade bundle
|
Displays the upgraded images of all the devices on the Supervisor.
|
show cable image-upgrade bundle, page 3-108
|
show cable image-upgrade status
|
Displays the upgrade status for a line card.
|
show cable image-upgrade status, page 3-110
|
show cable image-upgrade version
|
Displays all the upgraded image versions on the line card.
|
show cable image-upgrade version, page 3-111
|
DOCSIS Timing Interface (DTI)
|
cable clock free-run
|
Allows the clock to be in free-run mode.
|
cable clock free-run, page 3-8
|
clear cable clock counters
|
Clears DTI client transition counters of a TCC DTI client and server.
|
clear cable clock counters, page 3-50
|
show cable clock
|
Displays information about displaying Timing, Communication and Control (TCC) card DTI client and server statistic counts.
|
show cable clock, page 3-96
|
DOCSIS Timing Interface (DTI) Offset
|
cable depi offset
|
Sets the DOCSIS timing offset on the QAM channel for a line card in DEPI mode.
|
cable depi offset, page 3-10
|
show cable depi-sessions offset
|
Displays the DTI timing value on the QAM channels.
|
show cable heartbeat, page 3-106
|
Modular Cable Modem Termination System (M-CMTS)
|
cable depi dest-ip
|
Configures Downstream External PHY Interface (DEPI) sessions manually on QAM line cards.
|
cable depi dest-ip, page 3-9
|
depi class
|
Creates a template of DEPI control plane configuration settings and enters DEPI class configuration mode.
|
depi-class, page 3-57
|
depi tunnel
|
Creates a template of DEPI tunnel configuration settings and enters DEPI data session configuration mode.
|
depi-tunnel, page 3-59
|
dest-ip
|
Assigns an IP address to the EQAM.
|
dest-ip, page 3-62
|
depi eqam-stats
|
Enables debugging information for DEPI EQAM statistics on the Cisco RFGW-10.
|
depi eqam-stats, page 3-63
|
l2tp-class
|
Creates a template of Layer 2 Tunnel Protocol (L2TP) control plane configuration settings and enters L2TP class configuration mode.
|
l2tp-class, page 3-70
|
protect-tunnel
|
Configures a DEPI tunnel on the Cisco RFGW-10.
|
protect-tunnel, page 3-79
|
show cable depi-sessions
|
Displays DEPI sessions configured on the line card.
|
show cable depi-sessions, page 3-100
|
show cable depi-sessions slot count
|
Displays the DEPI session count on all QAMs on a line card.
|
show cable depi-sessions slot count, page 3-105
|
show controllers linecard
|
Displays information about used bandwidth and total bandwidth on all QAMs on a line card interface.
|
show controllers linecard, page 3-142
|
show depi
|
Displays DEPI information.
|
show depi, page 3-145
|
show depi session
|
Displays DEPI session information.
|
show depi session, page 3-147
|
Platform
|
banner lcd
|
Configures the string on the front panel display.
|
banner lcd, page 3-7
|
hw-module module power
|
Powers on a cable interface line card manually.
|
hw-module module power, page 3-64
|
show cable heartbeat
|
Displays the number of heartbeats received from the line cards.
|
show cable heartbeat, page 3-106
|
show cable linecard coreinfo
|
Copies the core file information from line card flash directory to the bootflash.
|
show cable linecard coreinfo, page 3-113
|
show cable linecard cpuload
|
Displays the CPU utilization information of the line card.
|
show cable linecard cpuload, page 3-115
|
show cable linecard logs
|
Displays the system log information of the line card at bootup.
|
show cable linecard logs, page 3-117
|
show cable linecard process
|
Displays all the processes running on the line card.
|
show cable linecard process, page 3-119
|
show cable linecard version
|
Displays image version information of the line card.
|
show cable linecard version, page 3-121
|
Redundancy
|
auto-sync
|
Enable automatic synchronization of the configuration files in NVRAM.
|
auto-sync, page 3-5
|
class
|
Configures redundancy class on the line card.
|
class, page 3-48
|
description
|
Adds a description to the line card group.
|
description, page 3-61
|
linecard-group internal switch
|
Configures a redundancy line card group.
|
linecard-group internal switch, page 3-72
|
main-cpu
|
Enters the main CPU redundancy configuration mode.
|
main-cpu, page 3-73
|
member slot
|
Adds a slot to the line card redundancy group.
|
member slot, page 3-74
|
mode
|
Configures the redundancy mode of operation.
|
mode, page 3-77
|
redundancy
|
Enters the redundancy configuration mode.
|
redundancy, page 3-83
|
redundancy force-failover main-cpu
|
Forces a switchover so that a standby Supervisor module becomes the active Supervisor module.
|
redundancy force-failover main-cpu, page 3-85
|
redundancy force-switchover
|
Forces the standby Route Processor (RP) or standby Supervisor to assume the role of an active RP or Supervisor.
|
redundancy force-switchover, page 3-87
|
redundancy linecard-group switchover from slot
|
Initiates a line card switchover.
|
redundancy linecard-group switchover from slot, page 3-89
|
redundancy reload
|
Resets the standby Supervisor to reset both the active and standby Supervisors.
|
redundancy reload, page 3-90
|
redundancy tcc-group switchover from slot
|
Initiates a Timing Control Card (TCC) switchover.
|
redundancy tcc-group switchover from slot, page 3-92
|
show redundancy
|
Displays the current active and standby Supervisor redundancy status.
|
show redundancy, page 3-157
|
show redundancy linecard
|
Displays information on a line card or line card group redundancy status.
|
show redundancy linecard, page 3-161
|
show redundancy tcc
|
Displays information of the TCC cards redundancy status.
|
show redundancy tcc, page 3-164
|
Universal QAM
|
cable downstream annex
|
Sets the MPEG framing format for a downstream port on a line card to Annex A (Europe) or Annex B (North America) or Annex C (Japan).
|
cable downstream annex, page 3-12
|
cable downstream frequency
|
Sets the center frequency on the line card.
|
cable downstream frequency, page 3-13
|
cable downstream if-output
|
Activates a downstream port on an interface and generates a standard modulated signal or a test signal.
|
cable downstream if-output, page 3-15
|
cable downstream interleave-depth
|
Sets the downstream interleave depth on the line card.
|
cable downstream interleave-depth, page 3-17
|
cable downstream interleaver-level
|
Sets the downstream interleave level on the line card.
|
cable downstream interleaver-level, page 3-19
|
cable downstream lock
|
Locks the downstream port on the QAM interface.
|
cable downstream lock, page 3-20
|
cable downstream modulation
|
Sets the modulation format for a downstream port on a line card.
|
cable downstream modulation, page 3-21
|
cable downstream rf-power
|
Configures the specified RF output power on the integrated upconverter.
|
cable downstream rf-power, page 3-22
|
cable downstream rf-shutdown
|
Enables or disables the RF output from the integrated upconverter.
|
cable downstream rf-shutdown, page 3-24
|
cable downstream stacking
|
Configures frequency stacking on the line card.
|
cable downstream stacking, page 3-25
|
cable downstream tsid
|
Configures the TSID value on the QAM subinterface.
|
cable downstream tsid, page 3-26
|
cable mode
|
Sets the mode on the QAM channel.
|
cable mode, page 3-29
|
interface qam
|
Configures a QAM interface on the line card.
|
interface qam, page 3-65
|
show controllers qam
|
Displays cable downstream information configured on the QAM channel and port.
|
show controllers qam, page 3-143
|
show interfaces qam
|
Displays information of the QAM interface.
|
show interfaces qam, page 3-153
|
show running-config interface qam
|
Displays the running configuration of the QAM interface.
|
show running-config interface qam, page 3-165
|
Video
|
active
|
Activates the video server group on the line card.
|
active, page 3-2
|
asm
|
Configures Any Source Multicast (ASM) label definition.
|
asm, page 3-3
|
cable qam-domain
|
Configures a QAM domain.
|
cable qam-domain, page 3-31
|
cable video group
|
Creates a group of unicast video sessions.
|
cable video group, page 3-33
|
cable video labels
|
Configures video session labels.
|
cable video labels, page 3-35
|
cable video multicast
|
Configures video multicast sessions on a QAM interface.
|
cable video multicast, page 3-36
|
cable video multicast uplink
|
Sets up an uplink port for multicast traffic.
|
cable video multicast uplink, page 3-38
|
clear cable video packet
|
Clears all video packet insertions.
|
clear cable video packet, page 3-53
|
clear cable video server-group statistics
|
Clears all video server-group statistics.
|
clear cable video server-group statistics, page 3-55
|
cable video psi-interval
|
Configures the PSI interval on the QAM subinterface.
|
cable video psi-interval, page 3-40
|
cable video servers
|
Configures server groups for video sessions using external servers.
|
cable video servers, page 3-41
|
cable video table
|
Configures video sessions on a QAM channel using the pre-defined UDP map.
|
cable video table, page 3-43
|
cable video timeout
|
Configures the video session timeout thresholds.
|
cable video timeout, page 3-44
|
cable video udp
|
Configures a unicast video session.
|
cable video udp, page 3-46
|
ip
|
Configures destination IP address for video sessions on a QAM domain.
|
ip, page 3-66
|
ip multicast-routing
|
Enables video multicast routing.
|
ip multicast-routing, page 3-67
|
ip rpc portmapper
|
Establishes a remote procedure call (RPC) connection between an external server and an EQAM.
|
ip rpc portmapper, page 3-68
|
keepalive retry
|
Sends keepalive message to a remote client with a specified retry interval.
|
keepalive retry, page 3-69
|
mgmt-ip-address mac-address
|
Configures the management port IP address in a cable video server group.
|
mgmt-ip-address mac-address, page 3-76
|
protocol
|
Sets the protocol used by the server in a video server group.
|
protocol, page 3-81
|
reset interval
|
Sets the reset interval in video server configuration mode
|
reset interval, page 3-93
|
retry interval
|
Configures the retry time and interval time on the external server.
|
retry interval, page 3-94
|
server
|
Configures the external server IP address of video server group.
|
server, page 3-95
|
show cable video label
|
Displays the active video labels configured on the chassis.
|
show cable video label, page 3-123
|
show cable video multicast uplink
|
Displays the multicast uplink interfaces configured on the chassis.
|
show cable video multicast uplink, page 3-126
|
show cable video packets
|
Displays the cable video packets on the QAM interface.
|
show cable video packet, page 3-128
|
show cable video route
|
Displays video route information on the chassis.
|
show cable video route, page 3-130
|
show cable video server-group
|
Displays information on a video server group.
|
show cable video server-group, page 3-132
|
show cable video session
|
Displays the video session information.
|
show cable video session, page 3-134
|
show cable video statistics packet
|
Displays unicast and multicast video packets.
|
show cable video statistics packet, page 3-139
|
ssm
|
Configures Specific Source Multicast (SSM) label definition.
|
ssm, page 3-167
|
video route
|
Creates video policy routes to redirect traffic to the line cards.
|
video route, page 3-170
|
