Cisco IOS®ソフトウェアリリース12.1(3)XGでは、Cisco Small Office/Home Office(SOHO)77にPoint-to-Point Protocol over Ethernet(PPPoE)クライアント機能が導入されました。この機能により、PPPoE機能がルータに移行されます。Cisco SOHO77の背後に複数のPCを設置し、トラフィックがPPPoEセッションに送信される前に、データを暗号化してフィルタリングし、ネットワークアドレス変換(NAT)を実行できます。
このドキュメントでは、Cisco SOHO77の非同期転送モード(ATM)インターフェイス(DSLインターフェイス)で設定されたPPPoEクライアントを示します。この設定は、非対称デジタル加入者線(ADSL)WANインターフェイスカード(WIC)を搭載したCisco 1700000でも00000000000000000000000000000000000000000000000000000000000
Cisco 6400 ノード ルート プロセッサ(NRP)の設定は、アグリゲータとして使用されているルータや ATM インターフェイスを搭載しているルータにも使用可能です。
このドキュメントに特有の要件はありません。
このドキュメントの情報は、次のソフトウェアとハードウェアのバージョンに基づいています。
Cisco SOHO77 Customer Premises Equipment(CPE)IOSソフトウェアリリース12.1(3)XP2
Cisco 6400 UAC-NRP IOS ソフトウェア リリース 12.1(3)DC1
Cisco 6400 UAC-NSP IOS ソフトウェア リリース 12.1(3)DB
Cisco 6130 DSLAM-NI2 IOS ソフトウェア リリース 12.1(5)DA
このマニュアルの情報は、特定のラボ環境に置かれたデバイスに基づいて作成されました。このドキュメントで使用するすべてのデバイスは、初期(デフォルト)設定の状態から起動しています。実稼動中のネットワークで作業をしている場合、実際にコマンドを使用する前に、その潜在的な影響について理解しておく必要があります。
ドキュメント表記の詳細は、『シスコ テクニカル ティップスの表記法』を参照してください。
このセクションでは、このドキュメントで説明する機能を設定するために必要な情報を提供しています。
注:この文書で使用されているコマンドの詳細を調べるには、「Command Lookup ツール」を使用してください(登録ユーザのみ)。
このドキュメントでは、次のネットワーク セットアップを使用します。
このドキュメントでは、次の構成を使用します。
Cisco SOHO77
Cisco 6400
Cisco SOHO77 に PPPoE を設定するには、Virtual Private Dial-up Network(VPDN; 仮想プライベート ダイヤルアップ ネットワーク)コマンドを使用します。まず最初に、VPDN コマンドを設定します。
Cisco SOHO77 |
---|
! vpdn enable no vpdn logging !--- Default. ! vpdn-group pppoe request-dialin !--- The PPPoE client requests a session with the aggregation unit (6400 NRP). protocol pppoe ! !--- Internal Ethernet network. ! interface Ethernet0 ip address 10.92.1.182 255.255.255.0 ip nat inside !--- DSL interface. ! interface ATM0 no ip address no atm ilmi-keepalive bundle-enable dsl operating-mode auto hold-queue 224 in !--- all defaults !--- PPPoE runs on top of AAL5SNAP, but the encap aal5snap command is not used. ! interface ATM0.1 point-to-point pvc 1/1 pppoe-client dial-pool-number 1 !--- pvc 1/1 is an example value that you must change to match the value !--- used by the Internet Service Provider (ISP). ! !--- The PPPoE client code ties into a dialer interface, upon !--- which a virtual-access interface is cloned. ! interface Dialer1 ip address negotiated ip mtu 1492 !--- Ethernet MTU is 1500 by default. In other words, 1492 + PPPoE headers = 1500. ip nat outside encapsulation ppp dialer pool 1 !--- Ties to ATM interface. ppp authentication chap callin ppp chap hostname <hostname> ppp chap password <password> ! !--- The ISP instructs you about the type of authentication to use. !--- To change from PPP CHAP to PPP PAP, replace the following three lines: !--- ppp authentication chap callin !--- ppp chap hostname |
Cisco 6400 |
---|
*** local ppp user !--- You can also use AAA. username |
現在、この設定に使用できる確認手順はありません。
このセクションでは、設定のトラブルシューティングおよびデバッグに役立つ情報を説明します。
Cisco SOHO77 または Cisco 6400 上で PPPoE をデバッグする場合は、プロトコル スタックを考慮する必要があります。トラブルシューティングは最下層のプロトコル層から始めます。
DSL 物理層
ATM 層
イーサネット層
PPP 層
回線がアップし、トレーニングされていることを確認します。
次の例に示すようにshowコマンドを入力します。結果の出力は回線の状態を示しています。
show int atm0 ATM0 is up, line protocol is up Hardware is PQUICC_SAR (with Alcatel ADSL Module) show dsl interface atm0 !--- Look for "Showtime" in the first few lines. ATU-R (DS) ATU-C (US) Modem Status: Showtime (DMTDSL_SHOWTIME)
ATMインターフェイスがアップしている場合は、debug atm packetsコマンドを使用して、ISPから何かが着信しているかどうかを確認できます。
注:パケットの処理方法が異なるため、このコマンドでは発信パケットは表示されません。
次の例に示すようにdebug atm packetsコマンドを入力します。
debug atm packet 03:21:32: ATM0(I): VCD:0x2 VPI:0x1 VCI:0x1 Type:0x0 SAP:AAAA CTL:03 OUI:0080C2 TYPE:0007 Length:0x30 03:21:32: 0000 0050 7359 35B7 0001 96A4 84AC 8864 1100 0001 000E C021 09AB 000C 0235 03:21:32: 279F 0000 0000 03:21:32:
上記の出力には同じ Type、SAP、CTL、および OUI のフィールドが含まれ、着信した ATM パケットが AAL5SNAP であることが示されます。
完全なイーサネット フレームは、AAL5SNAP パケットに含まれます。debug ethernet packet というコマンドはありませんが、VPDN デバッグ操作を実行して PPPoE フレームを確認する必要があります。
参照用に、PPPoEフレームであるイーサネットフレームには、次の2つのethertypeのいずれかが含まれています。
0x8863 Ethertype = PPPoE 制御パケット(PPPoE セッションを処理する)。
0x8864 Ethertype = PPPoE データ パケット(PPP パケットを含む)。
PPPoE には 2 つのセッションが存在することに注意することが重要です。PPPoE セッションは、VPDN L2TP タイプのセッションであり、PPP セッションでもあります。そのため、PPPoE を確立できるように、PPPoE セッション確立フェーズと PPP セッション確立フェーズを用意しています。
終端には、通常、PPP 終端フェーズと PPPoE 終端フェーズの両方が関係しています。
PPPoE 確立フェーズは、次の 2 つのステップから構成されています。
ステップ 1:PPPoEクライアントとサーバ(MACアドレス)を特定します。
ステップ 2:セッションIDを割り当てます。
このフェーズが完了すると、他の PPP 接続と同様に、通常の PPP 確立が行われます。
デバッグするには、VPDN PPPoE デバッグを使用すると、PPPoE 接続フェーズの成功または失敗を確認できます。
次の例に示すように、debugコマンドを入力します。
#debug vpdn pppoe-events 06:17:58: Sending PADI: vc=1/1 !--- A broadcast Ethernet frame (here, encapsulated in ATM) requests !--- a PPPoE server with the message, "Is there a PPPoE server out there?" 06:18:00: PPPOE: we have got our pado, and the pado timer went off !--- This is a unicast reply from a PPPoE server (similar to a DHCP offer). 06:18:00: OUT PADR from PPPoE tunnel !--- This is a unicast reply to accept the offer. 06:18:00: IN PADS from PPPoE tunnel !--- This is a confirmation that completes the establishment.
PPP接続を開始します。PPP の確立は、通常の PPP の開始どおりに実行されます。PPPoEセッションが確立された後、次に示すようにshow vpdnコマンドを使用してステータスを取得できます。
#show vpdn %No active L2TP tunnels %No active L2F tunnels PPPoE Tunnel and Session Information Total tunnels 1 sessions 1 PPPoE Tunnel Information Session count: 1 PPPoE Session Information SID RemMAC LocMAC Intf VASt OIntf VC 1 0050.7359.35b7 0001.96a4.84ac Vi1 UP AT0 1 1
show vpdn session allコマンドを使用して、パケットカウント情報を取得します。次に示します。
show vpdn session all %No active L2TP tunnels %No active L2F tunnels PPPoE Session Information Total tunnels 1 sessions 1 session id: 1 local MAC address: 0001.96a4.84ac, remote MAC address: 0050.7359.35b7 virtual access interface: Vi1, outgoing interface: AT0, vc: 1/1 1656 packets sent, 1655 received, 24516 bytes sent, 24486 received
役に立つ場合があるその他の debug コマンドには debug vpdn pppoe-data、debug pppoe-errors、および debug pppoe-packets があります。
PPPoE セッションが確立されたら、PPP デバッグは、その他の PPP 確立の場合と同様に行えます。同じ debug ppp negotiation コマンドと debug ppp authentication コマンドを使用します。
注:次の例では、ホスト名は「client1」、リモートCisco 6400の名前は「nrp-b」です。
コマンドラインからPPPネゴシエーションまたはPPP認証をアクティブにします。結果の出力は次のようになります。
06:36:03: Vi1 PPP: Treating connection as a callout 06:36:03: Vi1 PPP: Phase is ESTABLISHING, Active Open [0 sess, 1 load] 06:36:03: Vi1 PPP: No remote authentication for call-out 06:36:03: Vi1 LCP: O CONFREQ [Closed] id 1 len 10 06:36:03: Vi1 LCP: MagicNumber 0x03013D43 (0x050603013D43) 06:36:03: Vi1 LCP: I CONFACK [REQsent] id 1 len 10 06:36:03: Vi1 LCP: MagicNumber 0x03013D43 (0x050603013D43) 06:36:05: Vi1 LCP: I CONFREQ [ACKrcvd] id 2 len 15 06:36:05: Vi1 LCP: AuthProto CHAP (0x0305C22305) 06:36:05: Vi1 LCP: MagicNumber 0x65E315E5 (0x050665E315E5) 06:36:05: Vi1 LCP: O CONFACK [ACKrcvd] id 2 len 15 06:36:05: Vi1 LCP: AuthProto CHAP (0x0305C22305) 06:36:05: Vi1 LCP: MagicNumber 0x65E315E5 (0x050665E315E5) 06:36:05: Vi1 LCP: State is Open 06:36:05: Vi1 PPP: Phase is AUTHENTICATING, by the peer [0 sess, 1 load] 06:36:05: Vi1 CHAP: I CHALLENGE id 9 len 26 from "nrp-b" 06:36:05: Vi1 CHAP: Using alternate hostname client1 06:36:05: Vi1 CHAP: Username nrp-b not found 06:36:05: Vi1 CHAP: Using default password 06:36:05: Vi1 CHAP: O RESPONSE id 9 len 28 from "client1" 06:36:05: Vi1 CHAP: I SUCCESS id 9 len 4 06:36:05: Vi1 PPP: Phase is FORWARDING [0 sess, 1 load] 06:36:05: Vi1 PPP: Phase is AUTHENTICATING [0 sess, 1 load] 06:36:05: Vi1 PPP: Phase is UP [0 sess, 1 load] 06:36:05: Vi1 IPCP: O CONFREQ [Closed] id 1 len 10 06:36:05: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) 06:36:05: Vi1 CDPCP: O CONFREQ [Closed] id 1 len 4 06:36:05: Vi1 IPCP: I CONFREQ [REQsent] id 1 len 10 06:36:05: Vi1 IPCP: Address 8.8.8.1 (0x030608080801) 06:36:05: Vi1 IPCP: Address 8.8.8.1 (0x030608080801) 06:36:05: Vi1 IPCP: Address 9.9.9.2 (0x030609090902) 06:36:05: Vi1 IPCP: O CONFREQ [ACKsent] id 2 len 10 06:36:05: Vi1 IPCP: Address 9.9.9.2 (0x030609090902) 06:36:05: Vi1 LCP: I PROTREJ [Open] id 3 len 10 protocol CDPCP (0x820701010004) 06:36:05: Vi1 CDPCP: State is Closed 06:36:05: Vi1 IPCP: I CONFACK [ACKsent] id 2 len 10 06:36:05: Vi1 IPCP: Address 9.9.9.2 (0x030609090902) 06:36:05: Vi1 IPCP: State is Open 06:36:05: Di1 IPCP: Install negotiated IP interface address 9.9.9.2 06:36:05: Di1 IPCP: Install route to 8.8.8.1 06:36:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up
Cisco 6400(PPPoE サーバ)をデバッグする場合は、Cisco SOHO77(クライアント)に使用したものと同じ上位へ向かう手順を使用します。 ただし、今回は、DSL 物理層で DSLAM をチェックする必要がある点が異なります。
DSL 物理層
ATM 層
イーサネット層
PPP 層
DSL 物理層をチェックするときは、DSLAM の DSL 統計情報を確認する必要があります。Cisco DSLAM の場合は、show dsl interface コマンドを使用します。
Cisco 6400 側でも、debug atm packet コマンドを使用できます。また、特定の PVC に Cisco 6400 を使用可能にします。
次のようにコマンド行から適切なパラメータを指定して、debug atm packetを入力します。
debug atm packet interface atm 0/0/0.182 vc 1/82
結果の出力は次のようになります。
4d04h: ATM0/0/0.182(I): VCD:0x3 VPI:0x1 VCI:0x52 Type:0x900 SAP:AAAA CTL:03 OUI:0080C2 TYPE:0007 Length:0x30 4d04h: 0000 0001 96A4 84AC 0050 7359 35B7 8864 1100 0001 000E C021 0A2E 000C 65E3 4d04h: 15E5 0000 0000
注:パケットの処理方法が異なるため、このコマンドでは発信パケットは表示されません。
Cisco SOHO77 と同様に、Cisco 6400 でも、PPPoE 確立の確認に同じ VPDN show コマンドとデバッグが使用できます。
次の例に、出力とともにコンテキスト内の show コマンドと debug コマンドを示します。必要に応じてこれらのコマンドを使用します。
#debug vpdn pppoe-events 4d04h: IN PADI from PPPoE tunnel 4d04h: OUT PADO from PPPoE tunnel 4d04h: IN PADR from PPPoE tunnel 4d04h: PPPoE: Create session 4d04h: PPPoE: VPN session created. 4d04h: OUT PADS from PPPoE tunnel #show vpdn %No active L2TP tunnels %No active L2F tunnels PPPoE Tunnel and Session Information Total tunnels 1 sessions 1 PPPoE Tunnel Information Session count: 1 PPPoE Session Information SID RemMAC LocMAC Intf VASt OIntf VC 1 0001.96a4.84ac 0050.7359.35b7 Vi4 UP AT0/0/0 1 82 #show vpdn session all nrp-b#show vpdn session all %No active L2TP tunnels %No active L2F tunnels PPPoE Session Information Total tunnels 1 sessions 1 session id: 1 local MAC address: 0050.7359.35b7, remote MAC address: 0001.96a4.84ac virtual access interface: Vi4, outgoing interface: AT0/0/0, vc: 1/82 30 packets sent, 28 received, 422 bytes sent, 395 received
その他の debug コマンドには debug vpdn pppoe-data、debug pppoe-errors、および debug pppoe-packets があります。
Cisco 6400からのPPPデバッグ出力を次に示します。これは、Cisco SOHO77からの以前のデバッグに対応しています。
コマンドラインインターフェイスから次のコマンドを入力します。
debug ppp negotiation and debug ppp authentication
結果の出力は次のようになります。
4d04h: Vi2 PPP: Treating connection as a dedicated line 4d04h: Vi2 PPP: Phase is ESTABLISHING, Active Open [0 sess, 1 load] 4d04h: Vi2 LCP: O CONFREQ [Closed] id 1 len 15 4d04h: Vi2 LCP: AuthProto CHAP (0x0305C22305) 4d04h: Vi2 LCP: MagicNumber 0x65F62814 (0x050665F62814) 4d04h: Vi2 LCP: I CONFREQ [REQsent] id 1 len 10 4d04h: Vi2 LCP: MagicNumber 0x03144FF9 (0x050603144FF9) 4d04h: Vi2 LCP: O CONFACK [REQsent] id 1 len 10 4d04h: Vi2 LCP: MagicNumber 0x03144FF9 (0x050603144FF9) 4d04h: Vi3 LCP: I ECHOREQ [Open] id 60 len 8 magic 0xA60C0000 4d04h: Vi3 LCP: O ECHOREP [Open] id 60 len 8 magic 0x51A0BEF6 4d04h: Vi2 LCP: TIMEout: State ACKsent 4d04h: Vi2 LCP: O CONFREQ [ACKsent] id 2 len 15 4d04h: Vi2 LCP: AuthProto CHAP (0x0305C22305) 4d04h: Vi2 LCP: MagicNumber 0x65F62814 (0x050665F62814) 4d04h: Vi2 LCP: I CONFACK [ACKsent] id 2 len 15 4d04h: Vi2 LCP: AuthProto CHAP (0x0305C22305) 4d04h: Vi2 LCP: MagicNumber 0x65F62814 (0x050665F62814) 4d04h: Vi2 LCP: State is Open 4d04h: Vi2 PPP: Phase is AUTHENTICATING, by this end [0 sess, 1 load] 4d04h: Vi2 CHAP: O CHALLENGE id 10 len 26 from "nrp-b" 4d04h: Vi2 CHAP: I RESPONSE id 10 len 28 from "client1" 4d04h: Vi2 PPP: Phase is FORWARDING [0 sess, 1 load] 4d04h: Vi2 PPP: Phase is AUTHENTICATING [0 sess, 1 load] 4d04h: Vi2 CHAP: O SUCCESS id 10 len 4 4d04h: Vi2 PPP: Phase is UP [0 sess, 1 load] 4d04h: Vi2 IPCP: O CONFREQ [Closed] id 1 len 10 4d04h: Vi2 IPCP: Address 8.8.8.1 (0x030608080801) 4d04h: Vi2 IPCP: I CONFREQ [REQsent] id 1 len 10 4d04h: Vi2 IPCP: Address 0.0.0.0 (0x030600000000) 4d04h: Vi2 IPCP: Pool returned 9.9.9.2 4d04h: Vi2 IPCP: O CONFNAK [REQsent] id 1 len 10 4d04h: Vi2 IPCP: Address 9.9.9.2 (0x030609090902) 4d04h: Vi2 CDPCP: I CONFREQ [Not negotiated] id 1 len 4 4d04h: Vi2 LCP: O PROTREJ [Open] id 3 len 10 protocol CDPCP (0x820701010004) 4d04h: Vi2 IPCP: I CONFACK [REQsent] id 1 len 10 4d04h: Vi2 IPCP: Address 8.8.8.1 (0x030608080801) 4d04h: Vi2 IPCP: I CONFREQ [ACKrcvd] id 2 len 10 4d04h: Vi2 IPCP: Address 9.9.9.2 (0x030609090902) 4d04h: Vi2 IPCP: O CONFACK [ACKrcvd] id 2 len 10 4d04h: Vi2 IPCP: Address 9.9.9.2 (0x030609090902) 4d04h: Vi2 IPCP: State is Open 4d04h: Vi2 IPCP: Install route to 9.9.9.2 4d04h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to up