Guest

Support

M

Hierarchical Navigation

  • Viewing Options

  • PDF (211.0 KB)
  • Feedback
M

Table Of Contents

M

maxactive (ccn subsystem edbs dbprofile)-IVR Only

maxsessions (ccn application)

maxsessions (ccn trigger http)-IVR Only

maxsessions (ccn trigger jtapi)

maxsessions (ccn trigger sip)

maxsessions (IMAP)

maxsteps (ccn engine)

messaging-gateway

messaging-gateway directory lookup

messaging-gateway directory lookup tui-prompt

messaging-gateway registration

mwi refresh

mwi sip


M


Last Updated: June 20, 2007

maxactive (ccn subsystem edbs dbprofile)-IVR Only

maxsessions (ccn application)

maxsessions (ccn trigger http)-IVR Only

maxsessions (ccn trigger jtapi)

maxsessions (ccn trigger sip)

maxsessions (IMAP)

maxsteps (ccn engine)

messaging-gateway

messaging-gateway directory lookup

messaging-gateway directory lookup tui-prompt

messaging-gateway registration

mwi refresh

mwi sip

maxactive (ccn subsystem edbs dbprofile)-IVR Only

To specify the maximum number of concurrent active connections to the Cisco Unity Express IVR enterprise database subsystem (EDBS), use the maxactive command in Cisco Unity Express IVR EDBS profile configuration mode. Use the no form of this command to set the maximum number of active connections to 0.

maxactive number

no maxactive number

Syntax Description

number

Maximum number of concurrent active connections to the external database.


Command Default

The default maximum number of concurrent active connections is twice the number of licensed Cisco Unity Express IVR sessions.

Command Modes

Cisco Unity Express IVR EDBS profile configuration

Command History

Cisco Unity Express Version
Modification

3.0

This command was introduced.


Usage Guidelines

After the ccn subsystem edbs profile command is successfully performed, use the maxactive command to specify the maximum number of concurrent active connections to the Cisco Unity Express IVR EDBS. Connection requests that are made after the maximum limit is reached cause connection failures. The maximum value that you can specify, which is also the default value, is twice the number of licensed Cisco Unity Express IVR sessions.

Examples

The following example sets the maximum number of concurrent active connections to the Cisco Unity Express IVR EDBS to 8:

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn subsystem edbs dbprofile mydbprofile
Adding new Database profile
se-10-0-0-0(config-dbprof)# maxactive 8
se-10-0-0-0(config-dbprof)# end
se-10-0-0-0(config)# exit

Related Commands

Command
Description

show ccn subsystem edbs dbprofile-IVR Only

Displays the Cisco Unity Express IVR EDBS profile settings.


maxsessions (ccn application)

To specify the maximum number of subscribers who can access an application simultaneously, use the maxsessions command in Cisco Unity Express configuration application mode. To set the number to 0, use the no form of this command.

maxsessions number

no maxsessions

Syntax Description

number

Number of subscribers who can access this application simultaneously. The maximum value is determined by the number of ports purchased for the application. The default value is the number of ports granted by the license.


Command Modes

Configuration application

Command History

Cisco Unity Express Release
Modification

1.0

This command was introduced on the Cisco Unity Express network module and in Cisco Unified Communications Manager Express 3.0.

1.1

This command was implemented on the advanced integration module (AIM) and in Cisco Unified Communications Manager 3.3(3).

1.1.2

This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.


Examples

The following example sets the maximum number of subscribers who can access the autoattendant application simultaneously to 12.

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn application autoattendant

se-10-0-0-0(config-application)# maxsessions 12

se-10-0-0-0(config-application)# end

se-10-0-0-0(config)# exit

Related Commands

Command
Description

ccn application

Configures the CCN applications, such as voice mail and auto attendant.

show ccn application

Displays the CCN application details.


maxsessions (ccn trigger http)-IVR Only

To configure the maximum number of simultaneous incoming Cisco Unity Express IVR HTTP-based sessions, use the maxsessions command in Cisco Unity Express IVR HTTP trigger configuration mode. Use the no form of this command to set the maximum number of simultaneous HTTP requests value to 0.

maxsessions maximum-sessions

no maxsessions maximum-sessions

Syntax Description

maximum-sessions

Maximum number of simultaneous sessions of HTTP-based requests for the Cisco Unity Express IVR licensed port.


Defaults

The default is the number of licensed Cisco Unity Express IVR sessions.

Command Modes

Cisco Unity Express IVR HTTP trigger configuration

Command History

Cisco Unity Express Version
Modification

3.0

This command was introduced.


Usage Guidelines

After the ccn trigger http command is successfully performed, use the maxsessions command to configure the maximum number of simultaneous incoming HTTP sessions for this trigger. The maximum value you can specify is limited by the number of licensed Cisco Unity Express IVR sessions. Use the default form of this command to set the maximum number of simultaneous HTTP requests to the number of licensed Cisco Unity Express IVR sessions.

Examples

The following example sets the maximum number of simultaneous sessions of incoming HTTP-based requests to 8:

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn trigger http urlname myhttpapp

Adding new trigger

se-10-0-0-0(config-trigger)# maxsessions 8

se-10-0-0-0(config-trigger)# end

se-10-0-0-0(config)# exit

Related Commands

Command
Description

show ccn trigger http-IVR Only

Displays the trigger and application settings. Use the show ccn trigger http command to display the Cisco Unity Express IVR HTTP-based trigger settings.


maxsessions (ccn trigger jtapi)

To specify the maximum number of subscribers who can access a JTAPI trigger simultaneously, use the maxsessions command in Cisco Unity Express configuration trigger mode. To set the number to 0, use the no form of this command.

maxsessions number

no maxsessions

Syntax Description

number

Number of subscribers who can access this trigger simultaneously. The maximum value is determined by the number of ports purchased for the application. The default value is the number of ports granted by the license.


Command Modes

Configuration trigger

Command History

Cisco Unity Express Release
Modification

1.0

This command was introduced on the Cisco Unity Express network module and in Cisco Unified Communications Manager Express 3.0.

1.1

This command was implemented on the advanced integration module (AIM) and in Cisco Unified Communications Manager 3.3(3).

1.1.2

This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.


Examples

The following example sets the maximum number of subscribers who can access the JTAPI phonenumber trigger simultaneously to 12.

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn trigger jtapi phonenumber 1234

se-10-0-0-0(config-trigger)# maxsessions 12

se-10-0-0-0(config-trigger)# end

se-10-0-0-0(config)# exit

Related Commands

Command
Description

ccn trigger jtapi phonenumber

Enters CCN configuration trigger mode.

show ccn trigger all

Displays the CCN trigger details.


maxsessions (ccn trigger sip)

To specify the maximum number of subscribers who can access a SIP trigger simultaneously, use the maxsessions command in Cisco Unity Express configuration trigger mode. To set the number to 0, use the no form of this command.

maxsessions number

no maxsessions

Syntax Description

number

Number of subscribers who can access this trigger simultaneously. The maximum value is determined by the number of ports purchased for the application. The default value is the number of ports granted by the license.


Command Modes

Configuration trigger

Command History

Cisco Unity Express Release
Modification

1.0

This command was introduced on the Cisco Unity Express network module and in Cisco Unified Communications Manager Express 3.0.

1.1

This command was implemented on the advanced integration module (AIM) and in Cisco Unified Communications Manager 3.3(3).

1.1.2

This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.


Examples

The following example sets the maximum number of subscribers who can access the SIP phonenumber trigger simultaneously to 12.

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn trigger sip phonenumber 1234

se-10-0-0-0(config-trigger)# maxsessions 12

se-10-0-0-0(config-trigger)# end

se-10-0-0-0(config)# exit

Related Commands

Command
Description

ccn trigger sip phonenumber

Enters CCN configuration trigger mode.

show ccn trigger all

Displays the CCN trigger details.


maxsessions (IMAP)

To specify the maximum number of simultaneous IMAP sessions, use the maxsessions command in IMAP configuration mode. To set the number to the default value 50, use the no or default form of this command.

maxsessions number

no maxsessions

default maxsessions

Syntax Description

number

Number of simultaneous IMAP sessions. Valid values are 1 to 50. The default value is 50.


Defaults

The default number of sessions is 50.

Command Modes

IMAP configuration

Command History

Cisco Unity Express Release
Modification

2.3

This command was introduced.


Usage Guidelines

Beginning with Cisco Unity Express 3.0, this command was supported on the AIM-CUE.

An error message appears if a value for number is greater than 50.

If a subscriber attempts to use the IMAP feature and the IMAP server is at its maximum number of sessions, the subscriber will see an error message.


Note The IMAP server must be restarted for this value to become active.


Examples

The following example sets the maximum number of simultaneous IMAP sessions to 12.

se-10-0-0-0# config t

se-10-0-0-0(config)# service imap

se-10-0-0-0(config-application)# maxsessions 12

se-10-0-0-0(config-application)# end

se-10-0-0-0(config)# exit

Related Commands

Command
Description

enable (IMAP)

Enables the IMAP feature.

groupname

Configures voice-mail group parameters.

service imap

Enters IMAP configuration mode.

session idletimeout (IMAP)

Specifies the IMAP session idletimeout value.

session security

Sets the IMAP client connection type.

show imap configuration

Displays all IMAP configuration parameters.

show imap sessions

Displays all active IMAP sessions.


maxsteps (ccn engine)

To specify the maximum number of steps that can be executed in an application, use the maxsteps command in Cisco Unity Express configuration engine mode. This command does not have a no form.

maxsteps number

Syntax Description

number

Maximum number of steps that can be executed in an application. The default value is 1000. Maximum number of steps is 10,000.


Defaults

1000 steps

Command Modes

Configuration engine

Command History

Cisco Unity Express Release
Modification

1.0

This command was introduced on the Cisco Unity Express network module and in Cisco Unified Communications Manager Express 3.0.

1.1

This command was implemented on the advanced integration module (AIM) and in Cisco Unified Communications Manager 3.3(3).

1.1.2

This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.


Examples

The following example sets the maximum number of steps in an application to 500.

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn engine

se-10-0-0-0(config-engine)# maxsteps 500

se-10-0-0-0(config-engine)# end

se-10-0-0-0(config)# exit

Related Commands

Command
Description

ccn application

Configures the CCN applications, such as voice mail and auto attendant.

ccn engine

Configures the features shared by all the Cisco Unity Express subsystems.

show ccn engine

Displays the CCN engine details.


messaging-gateway

To specify location information for the primary or secondary messaging gateway that is used for registration, use the messaging-gateway command in Cisco Unity Express gateway configuration mode. Use the no form of the command to negate the configuration for the messaging gateway registration.

messaging-gateway {primary | secondary} location-id umg-ip-addr

no messaging-gateway {primary | secondary} location-id umg-ip-addr

Syntax Description

primary

Indicates that the information is for the primary messaging gateway to which Cisco Unity Express is requesting to be registered.

secondary

Indicates that the information is for the secondary messaging gateway to which Cisco Unity Express is requesting to be registered.

location-id

ID number of the messaging gateway to which Cisco Unity Express is requesting to be registered.

ip-addr

IP address of the messaging gateway to which Cisco Unity Express is requesting to be registered.

port

 

Command Modes

Cisco Unity Express gateway configuration

Command History

Release
Modification

3.1

This command was introduced.


Usage Guidelines

This command enters gateway configuration mode and specifies the location ID and IP addrees ( or domain name) of the primary or secondary messaging gateway to which Cisco Unity Express is attempting to register.

Examples

The following example causes Cisco Unity Express to send a registration message the messaging gateway with an ID of 59000 and an IP address of 192.0.2.24:

se-10-0-0-0# config t
se-10-0-0-0(config)# messaging-gateway primary 59000 192.0.2.24

Related Commands

Command
Description

show messaging-gateway

Displays the details associated with the registration of the messaging gateway

messaging-gateway registration

Causes the endpoint (Cisco Unity Express) to send a registration message to its messaging gateway.


messaging-gateway directory lookup

To enable the remote directory lookup feature, use the messaging-gateway directory lookup command in Cisco Unity Express gateway configuration mode. Use the no form of the command to disable the remote directory lookup feature.

messaging-gateway directory lookup

no messaging-gateway directory lookup

Syntax Description

This command has no arguments or keywords.

Command Modes

Cisco Unity Express gateway configuration

Command History

Release
Modification

3.1

This command was introduced.


Usage Guidelines

The remote directory lookup feature is enabled by default when the messaging-gateway register is issued.

Examples

The following example enables the remote directory lookup feature:

se-10-0-0-0# config t
se-10-0-0-0(config)# messaging-gateway directory lookup

Related Commands

Command
Description

show messaging-gateway

Displays the details associated with the registration of the messaging gateway

messaging-gateway directory lookup tui-prompt

Enables confirmation of the remote directory lookup in TUI mode.


messaging-gateway directory lookup tui-prompt

To enable confirmation of the remote directory lookup in TUI mode, use the messaging-gateway directory lookup tui-prompt command in Cisco Unity Express gateway configuration mode. Use the no form of the command to disable the confirmation of remote directory lookup.

messaging-gateway directory lookup tui-prompt

no messaging-gateway directory lookup tui-prompt

Syntax Description

This command has no arguments or keywords.

Command Modes

Cisco Unity Express gateway configuration

Command History

Release
Modification

3.1

This command was introduced.


Usage Guidelines

This feature is disabled automatically when you disable the directory lookup feature using the no messaging-gateway directory lookup command. However, this feature is not automatically enabled when you enable the directory lookup feature by issuing the messaging-gateway directory lookup.

In addition, when you enable this feature, it also enables the remote directory lookup feature.

Examples

The following example enables the remote directory lookup feature:

se-10-0-0-0# config t
se-10-0-0-0(config)# messaging-gateway directory lookup tui-prompt

Related Commands

Command
Description

show messaging-gateway

Displays the details associated with the registration of the messaging gateway

messaging-gateway directory lookup tui-prompt

Enables the remote directory lookup feature.


messaging-gateway registration

To cause the endpoint (Cisco Unity Express) to automatically send a registration message to its messaging gateway, use the messaging-gateway registration command in Cisco Unity Express configuration mode. Use the no form of the command to disable autoregistration with the massaging gateway.

messaging-gateway registration

no messaging-gateway registration

Syntax Description

This command has no arguments or keywords.

Command Modes

Cisco Unity Express configuration

Command History

Release
Modification

3.1

This command was introduced.


Usage Guidelines

This command enters gateway configuration mode and first causes the endpoint (Cisco Unity Express) to send a registration message to its primary messaging gateway. If the registration fails, the message is send to the secondary messaging gateway, unless registration with the primary fails due to a configuration error.

Examples

The following example causes Cisco Unity Express to send a registration message the messaging gateway with an ID of 59000 and an IP address of 192.0.2.24:

se-10-0-0-0# config t
se-10-0-0-0 (config)# messaging-gateway directory lookup 59000 192.0.2.24

Related Commands

Command
Description

show messaging-gateway

Displays the details associated with the registration of the messaging gateway

messaging-gateway

Specifies the location ID and IP address for the primary or secondary messaging gateway.


mwi refresh

To refresh the message-waiting indicator (MWI) lights on one or more telephones, use the mwi refresh command in Cisco Unity Express EXEC mode.

mwi refresh {all | telephonenumber tel-number}

Syntax Description

all

Refreshes all telephones configured on the system.

telephonenumber tel-number

Refreshes the specified telephone number or extension.


Command Modes

Cisco Unity Express EXEC

Command History

Cisco Unity Express Release
Modification

1.0

This command was introduced on the Cisco Unity Express network module and in Cisco Unified Communications Manager Express 3.0.

1.1

This command was implemented on the advanced integration module (AIM) and in Cisco Unified Communications Manager 3.3(3).

1.1.2

This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.


Usage Guidelines

Use this command to update the MWI lights when they are not in synchronization with the stored voice messages.

Refreshing an extension that does not require it does not affect that extension.

Examples

The following example refreshes the MWIs for all telephones:
se-10-0-0-0> enable
se-10-0-0-0# mwi refresh all

The following example refreshes the MWI for extension 2015:

se-10-0-0-0> enable

se-10-0-0-0# mwi refresh telephonenumber 2015

Related Commands

Command
Description

show groups

Displays a list of all configured groups.

show users

Displays a list of all configured subscribers.

show voicemail

Displays the properties of the configured voice-mail system.


mwi sip

To set the message waiting indicator (MWI) notification mechanism, use the mwi sip command in Cisco Unity Express SIP configuration mode. To use the outcall mechanism, use the no or default form of this command.

mwi sip {outcall | sub-notify | unsolicited}

no mwi sip

default mwi sip

Syntax Description

outcall

Sends MWI notifications using the SIP outcall mechanism.

sub-notify

Sends MWI notifications using the Subscribe Notify mechanism.

unsolicited

Sends MWI notifications using the Unsolicited Notify mechanism.


Defaults

The default mechanism is outcall.

Command Modes

Cisco Unity Express SIP configuration

Command History

Cisco Unity Express Release
Modification

2.3

This command was introduced.


Usage Guidelines

Only Cisco Unified CME can use the SIP outcall mechanism for generating MWI notifications. Outcall will not work between Cisco Unity Express and a Cisco Unified Communications Manager system.


Note If the MWI notification option is outcall, configure the MWI on and off extensions. See "Configuring the MWI On and Off Extensions (Cisco Unified CME Only)" in the Cisco Unity Express 3.1 Voice-Mail and Auto-Attendant CLI Administrator Guide.


The outcall option is available for backward compatibility. It is recommended that you use either sub-notify or unsolicited for the MWi notification option.

To use the outcall option, Cisco Unified CME must configure each ephone-dn that is registered to receive MWI notifications as follows:

ephone-dn 30
  number 8000....
  mwi on
.
.
ephone-dn 31
  number 8001....
  mwi off

Both Cisco Unified CME and Cisco Unified Communications Manager in SRST mode can use the sub-notify and unsolicited mechanisms for generating MWI notifications. With these mechanisms, the MWI notifications will reflect the accurate status of messages in a subscriber's voice mailbox.

After an ephone-dn is configured with the sub-notify option, Cisco Unified CME sends a Subscribe message to Cisco Unity Express to register the phone for MWI notifications. When a new voice message arrives in the voice mailbox for the ephone-dn, Cisco Unity Express updates the MWI status. If Cisco Unity Express does not receive the Subscribe message for the ephone-dn, Cisco Unity Express will not update the MWI status when a new message arrives.

To use the sub-notify option, Cisco Unified CME must configure each ephone-dn that is registered to receive MWI notifications as follows:

For Cisco IOS Releases Prior to 12.3(11)T07

telephony-service
.
.
   mwi sip-server 10.100.9.6 transport udp port 5060 
   number 2010
.
ephone-dn 35
  mwi sip

For Cisco IOS Releases 12.3(11)T07 and Later

sip-ua
.
.
   mwi-server ipv4:10.100.9.6 transport udp port 5060 
   number 2010
.
ephone-dn 35
  mwi sip

For Cisco SRST Mode

sip-ua
.
.
   mwi-server ipv4:10.100.9.6 transport udp port 5060 
   number 2010
.
call-manager-fallback.
  mwi relay

The unsolicited option does not require Cisco Unified CME to send a subscription request for each ephone-dn to Cisco Unity Express for MWI notifications. Cisco Unity Express sends Notify messages to Cisco Unified CME whenever the voice mailbox for any ephone-dn receives a new message. In this way, the MWI status reflects the current voice mailbox message status.

To use the unsolicited option, Cisco Unified CME must configure each ephone-dn that is registered to receive MWI notifications as follows:

For Cisco IOS Releases Prior to 12.3(11)T07

telephony-service
.
.
   mwi sip-server 10.100.9.6 transport udp port 5060 unsolicited 
   number 2010
.
ephone-dn 35
  mwi sip

For Cisco IOS Release 12.3(11)T07 and Later

sip-ua
.
.
   mwi-server ipv4:10.100.9.6 transport udp port 5060 unsolicited
   number 2010
.
ephone-dn 35
  mwi sip

For Cisco SRST Mode
sip-ua
.
.
   mwi-server ipv4:10.100.9.6 transport udp port 5060 unsolicited
   number 2010
.
call-manager-fallback.
  mwi relay

The SIP server IP address used in these commands must be the IP address of Cisco Unity Express. In the examples shown above, this is 10.100.9.6.

Examples

The following example configures the MWI notification mechanism as SIP Notify:

se-10-0-0-0# config t
se-10-0-0-0(config)# ccn subsystem sip
se-10-0-0-0(config-sip)# mwi sip sub-notify
se-10-0-0-0(config-sip)# end
se-10-0-0-0(config)# end
se-10-0-0-0# 

Related Commands

Command
Description

ccn subsystem sip

Enters SIP configuration mode.

dtmf-relay

Sets the SIP DTMF relay mechanism.

show ccn sip subscription mwi

Displays the active MWI subscriptions.

show ccn subsystem sip

Displays the DTMF relay mechanism.

transfer-mode

Sets the transfer mode used by Cisco Unity Express for SIP calls.