Table Of Contents
email domain (network location id)
enabled (ccn reporting historical)
enabled (ccn subsystem edbs dbprofile)-IVR Only
enabled (ccn trigger http)-IVR Only
E
Last Updated: June 20, 2007
email domain (network location id)
enabled (ccn reporting historical)
enabled (ccn subsystem edbs dbprofile)-IVR Only
enabled (ccn trigger http)-IVR Only
email domain (network location id)
To configure the e-mail domain for a voice-mail location, use the email command in Cisco Unity Express location configuration mode. To remove the e-mail domain for a location, use the no form of this command.
email domain {name | ip-address}
no email domain {name | ip-address}
Syntax Description
name
Configures the e-mail domain hostname for the location.
ip-address
Configures the e-mail domain IP address for the location.
Defaults
No e-mail domain is configured.
Command Modes
Location configuration
Command History
Usage Guidelines
This command configures the e-mail domain name or IP address for the location. The domain name is added when a VPIM message is sent to the remote location (for example, "4843000@mycompany.com"). If you do not configure a domain name or IP address, the Cisco Unity Express system at this location cannot receive network messages.
Using the no form of this command removes the e-mail domain from the specified location.
Caution If you remove the e-mail domain for a remote network location, the system automatically disables networking from the Cisco Unity Express module to that location.
If you remove the e-mail domain for the local location, then networking on that Cisco Unity Express module is disabled.
To reenable a location, assign it a valid e-mail domain.
Examples
The following example configures the e-mail domain for network location 9 to 10.12.0.1.
se-10-0-0-0# config t
se-10-0-0-0(config)# network location id 9
se-10-0-0-0(config-location)# email domain 10.12.0.1
se-10-0-0-0(config-location)# end
se-10-0-0-0(config)#Related Commands
Command DescriptionConfigures the CCN applications, such as voice mail and auto attendant.
Displays the CCN application details.
enable (IMAP)
To enable the integrated messaging (IMAP) feature system wide, use the enable command in Cisco Unity Express IMAP mode. To disable the IMAP feature, use the no or default form of this command.
enable
no enable
default enable
Syntax Description
This command has no arguments or keywords.
Defaults
IMAP is disabled.
Command Modes
Cisco Unity Express IMAP
Command History
Usage Guidelines
This command is not available on the AIM.
Examples
The following example enables the IMAP feature:
se-10-0-0-0# config tse-10-0-0-0(config)# service imapse-10-0-0-0(config-imap)# enableRelated Commands
enable (network location)
To enable a network location to send and receive Cisco Unity Express voice mail messages, use the enable command in Cisco Unity Express location configuration mode. To disable the location, use the no form of this command.
enable
no enable
Syntax Description
This command has no arguments or keywords.
Defaults
Network locations are enabled.
Command Modes
Cisco Unity Express location configuration
Command History
Usage Guidelines
Network locations are enabled by default to send and receive Cisco Unity Express voice mail messages. Use the no enable command to prevent communication to the location. Use the enable command to reestablish communication to the network location.
Note The no enable command does not erase the network location from the Cisco Unity Express database.
Examples
The following example displays the details for network location 15 with networking disabled:
se-10-0-0-0# config tse-10-0-0-0(config)# network location id 15se-10-0-0-0(config-location)# no enable!!!WARNING!!!:Disabling location will disablenetworking to/from this location.Do you wish to continue[n]?:yse-10-0-0-0(config-location)# endse-10-0-0-0(config)# exitse-10-0-0-0#se-10-0-0-0# show network detail location id 15Name: houstonAbbreviation: houEmail domain: how.cue.abcdef.comMinimum extension length: 2Maximum extension length: 15Phone prefix: 4VPIM encoding: dynamicSend spoken name: enabledSend vCard: enabledState: disabledVPIM broadcast ID: vpim-broadcastSent msg count: 1Received msg count: 1The following example reestablishes voice-mail transmission to and from network location 15.
se-10-0-0-0# config tse-10-0-0-0(config)# network location id 15se-10-0-0-0(config-location)# enablese-10-0-0-0(config-location)# endse-10-0-0-0(config)# exitRelated Commands
Command Descriptionnetwork location
Specifies a network ID for a remote site.
show network detail
Displays details of a specified network location.
enable (VoiceView Express)
To enable the VoiceView Express feature, use the enable command in Cisco Unity Express VoiceView mode. To disable the VoiceView Express feature, use the no or default form of this command.
enable
no enable
default enable
Syntax Description
This command has no arguments or keywords.
Defaults
VoiceView Express is enabled.
Command Modes
Cisco Unity Express VoiceView Express
Command History
Cisco Unity Express Release Modification2.3
This command was introduced.
3.0
This command was implemented on the advanced integration module (AIM).
Usage Guidelines
This command is not available on the AIM for release 2.3 and earlier..
Examples
The following example enables the VoiceView Express feature:
se-10-0-0-0# config tse-10-0-0-0(config)# service voiceviewse-10-0-0-0(config-voiceview)# enableRelated Commands
enabled (ccn application)
To start an application, use the enabled command in Cisco Unity Express CCN configuration application mode. To disable the application, use the no form of this command.
enabled
no enabled
Syntax Description
This command has no arguments or keywords.
Command Modes
CCN configuration application
Command History
Examples
The following example enables the autoattendant application.
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn application autoattendant
se-10-0-0-0(config-application)# enabled
se-10-0-0-0(config-application)# end
se-10-0-0-0(config)#Related Commands
Command DescriptionConfigures the CCN applications, such as voice mail and auto attendant.
Displays the CCN application details.
enabled (ccn reporting historical)
To enable the Cisco Unity Express IVR reporting historical database, use the enabled command in the Cisco Unity Express IVR reporting historical configuration mode. Use the no form of this command to disable the historical reporting database.
enabled
no enabled
Syntax Description
This command has no arguments or keywords.
Command Default
The reporting historical database is enabled.
Command Modes
Cisco Unity Express IVR reporting historical configuration
Command History
Usage Guidelines
The reporting historical database is enabled by default. If the reporting historical database is disabled, call-related events are not stored in the database.
Examples
The following example disables the Cisco Unity Express IVR reporting historical database:
se-10-0-0-0# config tse-10-0-0-0(config)# ccn reporting historicalse-10-0-0-0(config-hrdm)# no enabledse-10-0-0-0(config-hrdm)# endse-10-0-0-0(config)# exitRelated Commands
Command DescriptionDisplays the Cisco Unity Express IVR reporting historical database configuration settings.
enabled (ccn subsystem edbs dbprofile)-IVR Only
To enable the Cisco Unity Express IVR enterprise database system (EDBS) profile for use in the database steps for running scripts, use the enabled command in Cisco Unity Express IVR EDBS profile configuration mode. Use the no form of this command to disable the database.
enabled
no enabled
Syntax Description
This command has no arguments or keywords.
Command Default
The EDBS profile is enabled.
Command Modes
Cisco Unity Express IVR EDBS profile configuration
Command History
Usage Guidelines
After configuring the database profile parameters, use the enabled command to enable the Cisco Unity Express IVR EDBS profile for use with scripts.
Examples
The following example disables the EDBS profile mydbprofile using the no form of the command:
se-10-0-0-0# config tse-10-0-0-0(config)# ccn subsystem edbs dbprofile mydbprofileAdding new Database profilese-10-0-0-0(config-dbprof)# no enabledse-10-0-0-0(config-dbprof)# endse-10-0-0-0(config)# exitRelated Commands
enabled (ccn trigger http)-IVR Only
To enable the Cisco Unity Express IVR HTTP-based URL and application trigger, use the enabled command in Cisco Unity Express IVR HTTP trigger configuration mode. Use the no form of this command to disable the trigger from processing the incoming HTTP request.
enabled
no enabled
Syntax Description
This command has no arguments or keywords.
Command Default
The HTTP-based trigger is enabled.
Command Modes
Cisco Unity Express IVR HTTP trigger configuration
Command History
Usage Guidelines
After configuring the HTTP trigger parameters, use the enabled command to start processing incoming HTTP requests.
Examples
The following example enables an HTTP-based trigger application:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn trigger http urlname myhttpapp
Adding new triggerse-10-0-0-0(config-trigger)# application myapplication
se-10-0-0-0(config-trigger)# enabled
se-10-0-0-0(config-trigger)# end
se-10-0-0-0(config)# exit
Related Commands
Command DescriptionDisplays the trigger and application settings. Use the show ccn trigger http command option to display the configured Cisco Unity Express IVR HTTP-based trigger settings.
enabled (ccn trigger jtapi)
To start a trigger, use the enabled command in Cisco Unity Express CCN configuration trigger mode. To disable the trigger, use the no form of this command.
enabled
no enabled
Syntax Description
This command has no arguments or keywords.
Command Modes
CCN configuration trigger mode
Command History
Examples
The following example enables the trigger 1234.
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn trigger jtapi phonenumber 1234
se-10-0-0-0(config-trigger)# enabled
se-10-0-0-0(config-trigger)# end
se-10-0-0-0(config)#Related Commands
enabled (ccn trigger sip)
To start a trigger, use the enabled command in Cisco Unity Express CCN configuration trigger mode. To disable the trigger, use the no form of this command.
enabled
no enabled
Syntax Description
This command has no arguments or keywords.
Command Modes
CCN configuration trigger mode
Command History
Examples
The following example enables the trigger 1234.
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn trigger sip phonenumber 1234
se-10-0-0-0(config-trigger)# enabled
se-10-0-0-0(config-trigger)# end
se-10-0-0-0(config)#Related Commands
erase startup-config
To erase the startup configuration, use the erase startup-config command in Cisco Unity Express EXEC mode.
erase startup-config
Syntax Description
This command has no arguments or keywords.
Command Modes
Cisco Unity Express EXEC
Command History
Examples
The following example deletes the startup configuration from flash memory:
se-10-0-0-0# erase startup-configRelated Commands