- Cisco Unified CME Commands: A
- Cisco Unified CME Commands: B
- Cisco Unified CME Commands: C
- Cisco Unified CME Commands: D
- Cisco Unified CME Commands: E
- Cisco Unified CME Commands: F
- Cisco Unified CME Commands: G
- Cisco Unified CME Commands: H
- Cisco Unified CME Commands: I
- Cisco Unified CME Commands: K
- Cisco Unified CME Commands: L
- Cisco Unified CME Commands: M
- Cisco Unified CME Commands: N
- Cisco Unified CME Commands: O
- Cisco Unified CME Commands: P
- Cisco Unified CME Commands: R
- Cisco Unified CME Commands: S1
- Cisco Unified CME Commands: S2
- Cisco Unified CME Commands: T
- Cisco Unified CME Commands: U
- Cisco Unified CME Commands: V
- Cisco Unified CME Commands: W
- Cisco Unified CME Commands: X
- Index
Cisco Unified CME Commands: O
olsontimezone
To set the Olson Timezone so that the correct local time is displayed on Cisco Unified SCCP IP phones or Cisco Unified SIP IP phones, use the olsontimezone command in telephony-service or voice register global configuration mode, respectively. To return to the default, use the no form of this command.
olsontimezone timezone version number
no olsontimezone
Syntax Description
|
timezone |
Olson Timezone names, which include the area (name of continent or ocean) and location (name of a specific location within that region, usually cities or small islands). |
||
|
version number |
Version of the tzupdater.jar or TzDataCSV.csv file. The version indicates whether the file needs to be updated or not.
|
Command Default
No Olson Timezone is set.
Command Modes
Telephony-service configuration (config-telephony)
Voice register global configuration (config-register-global)
Command History
|
Release |
Modification |
|---|---|
|
15.2(2)T |
This command was introduced. |
Usage Guidelines
Use the olsontimezone command in either telephony-service or voice register global configuration mode, with the current version of Oracle’s Olson Timezone updater tool, tzupdater.jar, to set the correct Olson Timezone.
For Cisco Unified 3911 and 3951 SIP IP phones and Cisco Unified 6921, 6941, 6961, and 6945 SCCP and SIP IP phones, the correct Olson Timezone updater file is TzDataCSV.csv. The TzDataCSV.csv file is created based on the tzupdater.jar file.
To set the correct time zone, you must determine the Olson Timezone area/location where the Cisco Unified CME is located and download the latest tzupdater.jar or TzDataCSV.csv to a TFTP server (such as flash or slot 0) that is accessible to the Cisco Unified CME.
After a complete reboot, the phone checks if the version of its configuration file is earlier or later than 2010o. If it is earlier, the phone loads the latest tzupdater.jar and uses that updater file to calculate the Olson Timezone.
To make the Olson Timezone feature backward compatible, both the time-zone and timezone commands are retained as legacy time zones. Because the olsontimezone command covers approximately 500 time zones (Version 2010o of the tzupdater.jar file supports approximately 453 Olson Timezone IDs.), this command takes precedence when either the time-zone or the timezone command (that covers a total of 90 to100 time zones only) is present at the same time as the olsontimezone command.
Examples
The following example shows 7:29 p.m. as the time set on a Cisco Unified 7961 SCCP IP phone in Buenos Aires on May 13, 2011:
Router(config)# tftp-server flash:tzupdater.jar Router(config)# tftp-server flash:TzDataCSV.csv Router(config)# telephony-service Router(config-telephony)# olsontimezone America/Argentina/Buenos Aires version 2010o Router(config-telephony)# create cnf-files Router(config-telephony)# time-zone 21 Router(config-telephony)# exit Router(config)# clock timezone CST -6 Router(config)# clock summer-time date 12 October 2010 2:00 26 April 2011 2:00 Router(config)# exit Router# clock set 19:29:00 13 May 2011 Router# configure terminal Router(config)# telephony-service Router(config-telephony)# reset
The following example shows 3:25 p.m. as the time set on a Cisco Unified 6921 SIP IP phone in Buenos Aires on November 17, 2011:
Router(config)# tftp-server slot0:tzupdater.jar Router(config)# tftp-server slot0:TzDataCSV.csv Router(config)# voice register global Router(config-register-global)# olsontimezone America/Argentina/Buenos Aires version 2010o Router(config-register-global)# create profile Router(config-register-global)# timezone 21 Router(config-register-global)# exit Router(config)# clock timezone CST -6 Router(config)# clock summer-time date 12 October 2010 2:00 26 April 2011 2:00 Router(config)# exit Router# clock set 15:25:00 17 November 2011 Router# configure terminal Router(config)# voice register global Router(config-register-global)# reset
Related Commands
|
Command |
Description |
|---|---|
|
time-zone |
Sets the time zone so that the correct local time is displayed on Cisco Unified SCCP IP phones in a Cisco Unified CME system. |
|
timezone |
Sets the time zone used for Cisco Unified SIP IP phones in a Cisco Unified CME system. |
olsontimezone
To set the Olson Timezone so that the correct local time is displayed on Cisco Unified SCCP IP phones or Cisco Unified SIP IP phones, use the olsontimezone command in telephony-service or voice register global configuration mode, respectively. To return to the default, use the no form of this command.
olsontimezone timezone version number
no olsontimezone
Syntax Description
|
timezone |
Olson Timezone names, which include the area (name of continent or ocean) and location (name of a specific location within that region, usually cities or small islands). |
||
|
version number |
Version of the tzupdater.jar or TzDataCSV.csv file. The version indicates whether the file needs to be updated or not.
|
Command Default
No Olson Timezone is set.
Command Modes
Telephony-service configuration (config-telephony)
Voice register global configuration (config-register-global)
Command History
|
Release |
Modification |
|---|---|
|
15.2(2)T |
This command was introduced. |
Usage Guidelines
Use the olsontimezone command in either telephony-service or voice register global configuration mode, with the current version of Oracle’s Olson Timezone updater tool, tzupdater.jar, to set the correct Olson Timezone.
For Cisco Unified 3911 and 3951 SIP IP phones and Cisco Unified 6921, 6941, 6961, and 6945 SCCP and SIP IP phones, the correct Olson Timezone updater file is TzDataCSV.csv. The TzDataCSV.csv file is created based on the tzupdater.jar file.
To set the correct time zone, you must determine the Olson Timezone area/location where the Cisco Unified CME is located and download the latest tzupdater.jar or TzDataCSV.csv to a TFTP server (such as flash or slot 0) that is accessible to the Cisco Unified CME.
After a complete reboot, the phone checks if the version of its configuration file is earlier or later than 2010o. If it is earlier, the phone loads the latest tzupdater.jar and uses that updater file to calculate the Olson Timezone.
To make the Olson Timezone feature backward compatible, both the time-zone and timezone commands are retained as legacy time zones. Because the olsontimezone command covers approximately 500 time zones (Version 2010o of the tzupdater.jar file supports approximately 453 Olson Timezone IDs.), this command takes precedence when either the time-zone or the timezone command (that covers a total of 90 to100 time zones only) is present at the same time as the olsontimezone command.
Examples
The following example shows 7:29 p.m. as the time set on a Cisco Unified 7961 SCCP IP phone in Buenos Aires on May 13, 2011:
Router(config)# tftp-server flash:tzupdater.jar Router(config)# tftp-server flash:TzDataCSV.csv Router(config)# telephony-service Router(config-telephony)# olsontimezone America/Argentina/Buenos Aires version 2010o Router(config-telephony)# create cnf-files Router(config-telephony)# time-zone 21 Router(config-telephony)# exit Router(config)# clock timezone CST -6 Router(config)# clock summer-time date 12 October 2010 2:00 26 April 2011 2:00 Router(config)# exit Router# clock set 19:29:00 13 May 2011 Router# configure terminal Router(config)# telephony-service Router(config-telephony)# reset
The following example shows 3:25 p.m. as the time set on a Cisco Unified 6921 SIP IP phone in Buenos Aires on November 17, 2011:
Router(config)# tftp-server slot0:tzupdater.jar Router(config)# tftp-server slot0:TzDataCSV.csv Router(config)# voice register global Router(config-register-global)# olsontimezone America/Argentina/Buenos Aires version 2010o Router(config-register-global)# create profile Router(config-register-global)# timezone 21 Router(config-register-global)# exit Router(config)# clock timezone CST -6 Router(config)# clock summer-time date 12 October 2010 2:00 26 April 2011 2:00 Router(config)# exit Router# clock set 15:25:00 17 November 2011 Router# configure terminal Router(config)# voice register global Router(config-register-global)# reset
Related Commands
|
Command |
Description |
|---|---|
|
time-zone |
Sets the time zone so that the correct local time is displayed on Cisco Unified SCCP IP phones in a Cisco Unified CME system. |
|
timezone |
Sets the time zone used for Cisco Unified SIP IP phones in a Cisco Unified CME system. |
overlap-signal
To configure overlap dialing in SCCP or SIP IP phones, use the overlap-signal command in ephone, ephone-template, telephony-service, voice register pool, voice register global, or voice register template configuration mode.
overlap-signal
Syntax Description
This command has no arguments or keywords.
Command Default
Overlap-signal is disabled.
Command Modes
Call-manager-fallback
Ephone configuration (config-ephone)
Ephone-template configuration (config-ephone-template)
Telephony-service configuration (config-telephony)
Voice register pool (config-register-pool)
Voice register global configuration (config-register-global)
Voice register template (config-register-template)
Command History
|
Cisco IOS Release |
Cisco Product |
Modification |
|---|---|---|
|
15.1(3)T |
Cisco Unified CME 8.5 Cisco Unified SRST 8.5 |
This command was introduced. |
Usage Guidelines
SCCP IP phones
In SCCP IP phones, overlap dialing is enabled when the overlap signal command is configured in ephone, ephone-template, and telephony-service configurations modes.
SIP IP phones
In SIP IP Phones, overlap dialing is enabled when the overlap signal command is configured in voice register pool, voice register global, and voice register template configuration modes.
Cisco Unified SRST
In Cisco Unified SRST, overlap dialing is enabled on SCCP IP phones when overlap signal command is configured in call-manager-fallback configuration mode.
Examples
The following example shows overlap-signal enabled on SCCP phones:
Router# show running config ! ! telephony-service max-ephones 25 max-dn 15 load 7906 SCCP11.8-5-3S.loads load 7911 SCCP11.8-5-3S.loads load 7921 CP7921G-1.3.3.LOADS load 7941 SCCP41.8-5-3S.loads load 7942 SCCP42.8-5-3S.loads load 7961 SCCP41.8-5-3S.loads load 7962 SCCP42.8-5-3S.loads max-conferences 12 gain -6 web admin system name cisco password cisco transfer-system full-consult create cnf-files version-stamp Jan 01 2002 00:00:00 overlap-signal ! ephone-template 1 button-layout 1 line button-layout 3-6 blf-speed-dial ! ephone-template 9 feature-button 1 Endcall feature-button 3 Mobility ! ! ephone-template 10 feature-button 1 Park feature-button 2 MeetMe feature-button 3 CallBack button-layout 1 line button-layout 2-4 speed-dial button-layout 5-6 blf-speed-dial overlap-signal ! ephone 10 device-security-mode none mac-address 02EA.EAEA.0010 overlap-signal
!
The following example shows overlap-signal configured in voice register global and voice register pool 10:
Router#show running config ! ! ! voice service voip ip address trusted list ipv4 20.20.20.1 media flow-around allow-connections sip to sip ! voice class media 10 media flow-around ! ! voice register global max-pool 10 overlap-signal ! voice register pool 5 overlap-signal ! ! !
The following example shows overlap-signal configured in call-manager-fallback mode:
Router# show run | sec call-manager call-manager-fallback max-conferences 12 gain -6 transfer-system full-consult overlap-signal
overwrite-dyn-stats (voice hunt-group)
To overwrite statistics of previously joined dynamic agent with statistics of newly joined dynamic agents for voice hunt group, use the overwrite-dyn-stats command in voice hunt-group configuration mode. To remove the configuration, use the no form of this command.
overwrite-dyn-stats
no overwrite-dyn-stats
Syntax Description
This command has no arguments or keywords.
Command Default
By default, this command is disabled.
Command Modes
voice hunt group configuration (config-voice-hunt-group)
Command History
|
Cisco IOS Release |
Cisco Product |
Modification |
|---|---|---|
|
15.6(3)M 16.3.1 |
Cisco Unified CME 11.5 |
This command was introduced. |
Usage Guidelines
This command is configured to overwrite statistics of previously joined dynamic agent with statistics of newly joined dynamic agents for voice hunt group. To remove the configuration, use the no form of this command. The statistics for the first 32 members (both dynamic and static members) joining in an hour are collected in the 32 statistic slots allotted. If any of the static members logout and login during the hour, that member is allotted the same slot as previous. In scenarios where free slots are available, free slots are used to write statistics of the newly joined dynamic agent. Once all the 32 slots are exhausted and a new dynamic member tries to join within the same hour, the overwrite-dyn-stats CLI takes effect. Using the CLI, the hunt statistic slot for the first dynamic member that joined the hunt-group is overwritten with the statistics of the newly joined dynamic member. The overwriting for statistics will continue at the same slot.
Examples
The following example shows how the voice hunt group overwrite-dyn-stats option is enabled:
Router(config)# voice hunt-group 1 parallel Router(config-voice-hunt-group)# overwrite-dyn-stats
Feedback