Cisco Unified JTAPI Developers Guide for Cisco Unified Communications Manager Release 10.0(1)
New and changed information
Downloads: This chapterpdf (PDF - 1.22MB) The complete bookPDF (PDF - 24.46MB) | The complete bookePub (ePub - 5.02MB) | Feedback

New and changed information

This chapter describes new and changed JTAPI information for Cisco Unified Communications Manager, Release 9.0(1) and features supported in the previous releases.

For more information, go to the Programming Guides website at http:/​/​www.cisco.com/​en/​US/​products/​sw/​voicesw/​ps556/​products_​programming_​reference_​guides_​list.html.

Cisco Unified Communications Manager release 9.0(1)

This section describes the new and changed features in Cisco Unified Communications Manager release 9.0(1):

Cisco Unified Communications Manager release 8.6(1)

This section describes the new and changed features in Cisco Unified Communications Manager release 8.6(1):

Cisco Unified Communications Manager release 8.5(1)

This section describes the new and changed features in Cisco Unified Communications Manager release 8.5(1):

Cisco Unified Communications Manager release 7.1(3)

This section describes the new and changed features in Cisco Unified Communications Manager release 7.1(3):

Cisco Unified Communications Manager release 7.0(1)

This section describes the new and changed features in Cisco Unified Communications Manager from release 6.1 to release 7.0(1) and Cisco Unified JTAPI enhancements. It has the following sections:


Note


Cisco Unified Communications Manager release 7.0(1) does not support the following IPv6 related methods:

canSupportIPv6()

setProviderOpenRetryAttempts (int retryAttempts)

getProviderOpenRetryAttempts()

getIPAddressingMode() (available on CiscoMediaTerminal and CiscoRouteTerminal interfaces)

register(java.net.InetAddress address, int port, CiscoMediaCapability [] capabilities, int[] algorithmIDs, java.net.InetAddress address_v6, int activeAddressingMode)

register(CiscoMediaCapability [] capabilities, int[] int registration Type, int[] algorithmIDs, int activeAddressingMode)

getTerminals() (available on new interface CiscoProviderTermCapabilityChangedEv)

getAddressingModeForMedia()

getCallingPartyIpAddr_v6() (available on CiscoCallCtlConnOfferedEv and CiscoRouteEvent interfaces)

CTIERR_IPADDRMODEMISMATCH

CTIERR_DYNREG_IPADDRMODE_MISMATCH

hasIPv6CapabilityChanged()

CiscoTerminal.IP_ADDRESSING_MODE_IPv4

CiscoTerminal.IP_ADDRESSING_MODE_IPv6

CiscoTerminal.IP_ADDRESSING_MODE_IPv4_v6

CiscoTerminal.IP_ADDRESSING_MODE_Unknown

CiscoTermRegistrationFailedEv.IP_ADDRESSING_MODE_MISMATCH



Note


For the features, Join Across Lines, Do Not Disturb-Reject, and Calling Party Normalization, each Cisco JTAPI must be upgraded to a version that supports these features. Additionally, if you are upgrading from release 5.1 and you use Join Across Lines, the Conference Chaining feature must not be enabled or used until all applications are either upgraded to a version compatible with the new unified CM version. Also, you should verify that the applications are not impacted by the Conference Chaining feature.


Cisco Unified Communications Manager release 6.1

This section describes the new and changed features in Cisco Unified Communications Manager from release 6.0 to release 6.1 and Cisco Unified JTAPI enhancements. It has the following sections:

Cisco Unified Communications Manager release 5.1

This section describes the new and changed features in Cisco Unified Communications Manager, from release 5.0 to release 5.1 and Cisco Unified JTAPI enhancements. It has the following sections: