Installation Guide for Cisco Unity Connection Release 7.x
Installing the Operating System and Cisco Unity Connection
Downloads: This chapterpdf (PDF - 391.0KB) The complete bookPDF (PDF - 1.36MB) | Feedback

Installing the Operating System and Cisco Unity Connection

Table Of Contents

Installing the Operating System and Cisco Unity Connection

Installation Scenarios

Install Software from a DVD on the First Node (on a Connection Publisher Server) or on a Connection Server Without a Connection Cluster

Install Software from a DVD on a Subsequent Node (on a Connection Subscriber Server)

Apply a Patch During Installation of the First Node (a Connection Publisher Server) or of a Connection Server Without a Connection Cluster

Apply a Patch During Installation of a Subsequent Node (a Connection Subscriber Server)

Preinstallation Tasks

Important Considerations

Frequently Asked Questions About the Installation

How Much Time Does the Installation Require?

What Usernames and Passwords Do I Need to Specify?

What Is a Strong Password?

Which Servers Does Cisco Support for this Installation?

May I Install Other Software on the Server?

Browser Requirements

Installing a Memory Upgrade or Replacing Hard Disks (Selected Servers Only)

Configuring the Hardware

Verifying DNS Registration

Gathering Information for an Installation

Using the Cisco Unified Communications Answer File Generator

Handling Network Errors During Installation

Installing the New Operating System and Application

Navigating Within the Installation Wizard

Starting the Installation

Entering Preexisting Configuration Information

Applying a Patch

Upgrading from a Local Disk

Upgrading from a Remote Server

Performing the Basic Installation

Configuring the First Node

Configuring a Subsequent Node

Postinstallation Tasks

Changing the Default Application User Passwords

Activating Services

Examining Log Files


Installing the Operating System and Cisco Unity Connection


This chapter contains the following sections:

Installation Scenarios

Install Software from a DVD on the First Node (on a Connection Publisher Server) or on a Connection Server Without a Connection Cluster

Install Software from a DVD on a Subsequent Node (on a Connection Subscriber Server)

Apply a Patch During Installation of the First Node (a Connection Publisher Server) or of a Connection Server Without a Connection Cluster

Apply a Patch During Installation of a Subsequent Node (a Connection Subscriber Server)

Preinstallation Tasks

Important Considerations

Frequently Asked Questions About the Installation

How Much Time Does the Installation Require?

What Usernames and Passwords Do I Need to Specify?

What Is a Strong Password?

Which Servers Does Cisco Support for this Installation?

May I Install Other Software on the Server?

Browser Requirements

Installing a Memory Upgrade or Replacing Hard Disks (Selected Servers Only)

Configuring the Hardware

Verifying DNS Registration

Gathering Information for an Installation

Using the Cisco Unified Communications Answer File Generator

Handling Network Errors During Installation

Installing the New Operating System and Application

Navigating Within the Installation Wizard

Starting the Installation

Entering Preexisting Configuration Information

Applying a Patch

Performing the Basic Installation

Configuring the First Node

Configuring a Subsequent Node

Postinstallation Tasks

Changing the Default Application User Passwords

Activating Services

Examining Log Files

Installation Scenarios

You can use this document to perform the following different installation scenarios:

Install software from a DVD on the first node

Install software from a DVD on a subsequent node

Apply a patch during installation of the first node

Apply a patch during installation of a subsequent node

The following sections provide an overview of the high-level tasks that you must perform for each of these installation scenarios. Each high-level task also includes a link to another section of the document, which you can follow for detailed information about the task.

Install Software from a DVD on the First Node (on a Connection Publisher Server) or on a Connection Server Without a Connection Cluster

To install software that you have on a DVD on the first node (on the Connection publisher server) in a cluster or on a Connection server without a Connection cluster, follow the steps in Table 2-1.

Table 2-1 Installing Software from a DVD on the First Node 

 
Task
For More Information

Step 1 

Perform all preinstallation tasks that apply to your site.

For a list of preinstallation tasks, see Table 2-5.

Step 2 

Follow the procedure to begin installing the software on the DVD to your server.

See the "Starting the Installation" section.

Step 3 

Follow the procedure for performing a basic installation.

See the "Performing the Basic Installation" section.

Step 4 

When the First Node Configuration window displays, choose Yes to configure the new server as the first node.

See Step 10 in the "Performing the Basic Installation" section.

Step 5 

Follow the procedure to configure the first node.

See "Configuring the First Node" section

Step 6 

Perform all postinstallation tasks that apply to your site.

For a list of postinstallation tasks, see Table 2-10.

Install Software from a DVD on a Subsequent Node (on a Connection Subscriber Server)

To install software that you have on a DVD on a Connection subscriber server, follow the steps in Table 2-2.

Table 2-2 Installing Software from a DVD on a Subsequent Node 

 
Task
For More Information

Step 1 

Perform all preinstallation tasks that apply to your site.

For a list of preinstallation tasks, see Table 2-5.

Step 2 

Follow the procedure to begin installing the software on the DVD to your server.

See "Starting the Installation" section.

Step 3 

Follow the procedure for performing a basic installation.

See "Performing the Basic Installation" section.

Step 4 

When the First Node Configuration displays, choose No to configure the new server as a subsequent node.

See Step 10 in the "Performing the Basic Installation" section.

Step 5 

Follow the procedure to configure a subsequent node in the cluster.

See the "Configuring a Subsequent Node" section.

Step 6 

Perform all postinstallation tasks that apply to your site.

For a list of postinstallation tasks, see Table 2-10.

Apply a Patch During Installation of the First Node (a Connection Publisher Server) or of a Connection Server Without a Connection Cluster

You can upgrade to a later release by downloading and applying a patch during installation. To apply a patch during installation of the first node (a Connection publisher server) or of a Connection server without a Connection cluster, follow the steps in Table 2-3.

Table 2-3 Applying a Patch During Installation of the First Node 

 
Task
For More Information

Step 1 

Perform all preinstallation tasks that apply to your site.

For a list of preinstallation tasks, see Table 2-5.

Step 2 

Follow the procedure to begin installing the software on the DVD to your server.

See "Starting the Installation" section.

Step 3 

Follow the procedure to apply a software patch.

See "Applying a Patch" section.

Step 4 

Follow the procedure for performing a basic installation.

See "Performing the Basic Installation" section.

Step 5 

When the First Node Configuration window displays, choose Yes to configure the new server as the first node.

See Step 10 in the "Performing the Basic Installation" section.

Step 6 

Follow the procedure to configure the first node in the cluster.

See the "Configuring the First Node" section.

Step 7 

Perform all postinstallation tasks that apply to your site.

For a list of postinstallation tasks, see Table 2-10.

Apply a Patch During Installation of a Subsequent Node (a Connection Subscriber Server)

You can upgrade to a later release by downloading and applying a patch during installation. To apply a patch during installation of a Connection subscriber server, follow the steps in Table 2-4.

Table 2-4 Applying a Patch During Installation of a Subsequent Node 

 
Task
For More Information

Step 1 

Perform all preinstallation tasks that apply to your site.

For a list of preinstallation tasks, see Table 2-5.

Step 2 

Follow the procedure to begin installing the software on the DVD to your server.

See "Starting the Installation" section.

Step 3 

Follow the procedure to apply a software patch.

See "Applying a Patch" section.

Step 4 

Follow the procedure for performing a basic installation.

See "Performing the Basic Installation" section.

Step 5 

When the First Node Configuration window displays, choose No to configure the new server as a subsequent node.

See Step 10 in the "Performing the Basic Installation" section.

Step 6 

Follow the procedure to configure a subsequent node in the cluster.

See the "Configuring a Subsequent Node" section.

Step 7 

Perform all postinstallation tasks that apply to your site.

For a list of postinstallation tasks, see Table 2-10.

Preinstallation Tasks

Table 2-5 contains a list of preinstallation tasks that you need to perform to ensure that you can successfully install Cisco Unity Connection.

Table 2-5 Preinstallation Tasks 

 
Task
Important Notes

Step 1 

Read this entire document to familiarize yourself with the installation procedure.

 

Step 2 

Verify the integrity of any new server hardware (such as hard drives and memory) by running any manufacturer-provided utilities.

 

Step 3 

Ensure that your servers are listed as supported hardware and sized appropriately to support the load of the cluster.

For information about the capacity of server models, see the Cisco Unity Connection Supported Platforms List at http://www.cisco.com/en/US/products/ps6509/products_data_sheets_list.html.

Make sure to account for any growth that has occurred since initial system configuration.

Step 4 

If you are getting the system time from an NTP server, verify that the first node can synchronize with the NTP server before you install a subsequent node.

To verify the NTP status of the first node, log into the Command Line Interface on the first node and enter the following command:

utils ntp status

For more information, see the Cisco Unified Communications Operating System Administration Guide.


Caution If the first node fails to synchronize with an NTP server, installation of a subsequent node can also fail.

Step 5 

If your firewall is not in the routing path, disable the firewall between nodes, if possible. Also, increase the firewall timeout settings until after you complete the installation.

To temporarily allow network traffic in and out of the nodes (for example, setting the firewall rule for these nodes to IP any/any) does not always suffice. The firewall might still close necessary network sessions between nodes due to timeouts.

Step 6 

Do not run Network Address Translation (NAT) or Port Address Translation (PAT) between Cisco Unity Connection nodes.

 

Step 7 

Record the network interface card (NIC) speed and duplex settings of the switch port to which you will connect the new server.

You should configure the same NIC settings on the server and on the switch port. For GigE (1000/FULL), you should set NIC and switch port settings to Auto/Auto; do not set hard values.

If you are using Network Fault Tolerance, the Network Fault Tolerance configuration gets lost during the replacement. You will need to configure it on each server after the upgrade.

Enable PortFast on all switch ports that are connected to Cisco servers. With Portfast enabled, the switch immediately brings a port from the blocking state into the forwarding state by eliminating the forwarding delay [the amount of time that a port waits before changing from its Spanning-Tree Protocol (STP) learning and listening states to the forwarding state].

Step 8 

If you use DNS, verify that all servers on which you plan to install Cisco Unity Connection are properly registered in DNS.

For more information, see the "Verifying DNS Registration" section.

Step 9 

Record the configurations settings for each server that you plan to install.

To record your configuration settings, see Table 2-8.

Step 10 

Configure any subsequent nodes on the first node before you install a subsequent node.

From Cisco Unified Communications Manager Administration on the first node, choose System > Server and configure the IP address for the subsequent nodes. For more information, see the Cisco Unified Communications Manager Administration Guide.

Important Considerations

Before you proceed with the installation, consider the following requirements and recommendations:

Be aware that when you install on an existing server, the hard drive gets formatted, and all existing data on the drive gets overwritten.

Ensure that you connect each Cisco Unity Connection node to an uninterruptible power supply (UPS) to provide backup power and protect your system. Failure to do so may result in damage to physical media and require a new installation.

When installing a Connection cluster, install the Cisco Unity Connection software on the first node (the publisher server) first and then on the subsequent node (the subscriber server).

When installing a Connection cluster, make sure that the subscriber server can connect to the publisher server during the installation.

When you enter the Security password on the first node, be sure that you write it down and save it. You must enter the same password on each subsequent node that you install in the cluster. Install the software during off-peak hours or a maintenance window to avoid impact from interruptions.

Both servers in a cluster must run the same release of Cisco Unity Connection. The only exception is during a cluster software upgrade, during which a temporary mismatch is allowed.

Configure the server by using static IP addressing to ensure that the server obtains a fixed IP address.

Do not attempt to perform any configuration tasks during the installation.

Do not install any Cisco-verified applications until you complete the installation.

Be aware that directory names and filenames that you enter while you are running the installation program are case-sensitive.

Disk mirroring on server model 7825 I3 with 160 GB SATA disk drives takes approximately 3 hours.

Disk mirroring on server model 7828 I3 with 250 GB SATA disk drives takes approximately 4 hours.

Carefully read the information that follows before you proceed with the installation.

Frequently Asked Questions About the Installation

The following section contains information about commonly asked questions and responses. Review this section carefully before you begin the installation.

How Much Time Does the Installation Require?

The entire installation process, excluding pre- and postinstallation tasks, takes 45 to 90 minutes, depending on your server type.

What Usernames and Passwords Do I Need to Specify?


Note The system checks your passwords for strength. For guidelines on creating a strong passwords, see the "What Is a Strong Password?" section.


During the installation, you must specify the following usernames and passwords:

Administrator Account username and password

Application User name and password

Security password

Administrator Account User Name and Password

You use the Administrator Account username and password to log in to the following areas:

Cisco Unified Communications Operating System Administration

Disaster Recovery System

Command Line Interface

To specify the Administrator Account username and password, follow these guidelines:

Administrator Account username—The Administrator Account username must start with an alphabetic character and can contain alphanumeric characters, hyphens and underscores.

Administrator Account password—The Administrator Account password must be at least six characters long and can contain alphanumeric characters, hyphens, and underscores.

You can change the Administrator Account password or add a new Administrator account by using the command line interface. For more information, see the Cisco Unified Communications Operating System Administration Guide.

Application User Name and Password

You use the Application User name and password to access applications that are installed on the system, including the following areas:

Cisco Unified Serviceability

Real-Time Monitoring Tool

To specify the Application User name and password, follow these guidelines:

Application User name—The Application User name must start with an alphabetic character and can contain alphanumeric characters, hyphens and underscores.

Application User password—The Application User password must be at least six characters long and can contain alphanumeric characters, hyphens, and underscores.

You can change the Application User name and password by using the command line interface. For more information, see the Cisco Unified Communications Operating System Administration Guide.

Security Password

When clustering is configured, Connection uses this password to authorize communications between the publisher and subscriber servers. You must ensure that this password is identical on both servers.

The Security password must be at least six characters long and can contain alphanumeric characters, hyphens, and underscores.

What Is a Strong Password?

The installation wizard checks to ensure that you enter a strong password. To create a strong password, follow these recommendations:

Mix uppercase and lowercase letters.

Mix letters and numbers.

Include hyphens and underscores.

Remember that longer passwords are stronger and more secure than shorter ones.

Avoid the following types of passwords:

Do not use recognizable words, such as proper names and dictionary words, even when combined with numbers.

Do not invert recognizable words.

Do not use word or number patterns, like aaabbb, qwerty, zyxwvuts, 123321, and so on.

Do not use recognizable words from other languages.

Do not use personal information of any kind, including birthdays, postal codes, names of children or pets, and so on.

Which Servers Does Cisco Support for this Installation?

For information about supported servers, see the Cisco Unity Connection Supported Platforms List at http://www.cisco.com/en/US/products/ps6509/products_data_sheets_list.html.

May I Install Other Software on the Server?

You must do all software installations and upgrades by using Cisco Unified Communications Operating System Administration. The system can upload and process only software that Cisco Systems approved. You cannot install or use unapproved third-party or Windows-based software applications.

Browser Requirements

You can access Cisco Unified Serviceability, Cisco Unified Communications Operating System Administration, and Disaster Recovery System by using the following browsers:

Microsoft Internet Explorer version 6.x or version 7.x

Netscape Navigator version 7.1 or later

For current browser requirements for accessing Cisco Unity Connection Administration and Cisco Unity Connection Serviceability, see the "Software Requirements—Administrator Workstations" section of System Requirements for Cisco Unity Connection Release 7.x at http://www.cisco.com/en/US/docs/voice_ip_comm/connection/7x/requirements/7xcucsysreqs.html.

Cisco does not support or test browsers other than those documented here or in System Requirements.

Installing a Memory Upgrade or Replacing Hard Disks (Selected Servers Only)


Note If you are installing a server that does not require a memory upgrade or a hard-disk replacement, skip this section.


If you are upgrading an existing Cisco Unity Connection system to version 7.x and you want to retain user data and voice messages, see the applicable chapter of the Reconfiguration and Upgrade Guide for Cisco Unity Connection Release 7.x at http://www.cisco.com/en/US/docs/voice_ip_comm/connection/7x/upgrade/guide/7xcucrugx.html.

Some servers that are qualified for use with Cisco Unity Connection require:

A memory upgrade to run Connection 7.x in any configuration.

A memory upgrade to support a specified number of Connection users when both voice recognition and Digital Networking are configured.

A hard-disk replacement to support a Connection cluster.

See the applicable server-specific table in the Cisco Unity Connection Supported Platforms List at http://www.cisco.com/en/US/products/ps6509/products_data_sheets_list.html.


Warning Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord. Statement 1



Warning Before opening the chassis, disconnect the telephone-network cables to avoid contact with telephone-network voltages. Statement 2



Warning This equipment is to be installed and maintained by service personnel only as defined by AS/NZS 3260 Clause 1.2.14.3 Service Personnel. Statement 88



Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94



Warning The safety cover is an integral part of the product. Do not operate the unit without the safety cover installed. Operating the unit without the cover in place will invalidate the safety approvals and pose a risk of fire and electrical hazards. Statement 117



Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001



Warning Read the installation instructions before connecting the system to the power source. Statement 1004



Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety:
· This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
· When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.
· If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006



Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Statement 1015



Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017



Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021



Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023



Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024



Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029



Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030



Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040


(For translations of the preceding safety warnings, see Regulatory Compliance and Safety Information for Cisco Unity Connection at http://www.cisco.com/en/US/docs/voice_ip_comm/connection/regulatory/compliance/ucwarns.html.)

To Install a Memory Upgrade or Replace Hard Disks (Selected Servers Only)


Step 1 Remove the cover.

Step 2 If you are not installing a memory upgrade, skip to Step 3.

Install the memory modules in the applicable slots or locations, depending on the server model, as documented in the Cisco Unity Connection Supported Platforms List.


Caution If you install new memory modules in the wrong slots, the server and operating system may not recognize that the modules have been installed, and Cisco Unity Connection performance may suffer.

Step 3 If you are not replacing hard disks, skip to Step 4.


Caution If you are replacing hard disks, you must remove existing hard disks and install exactly as many hard disks as you remove, or Cisco Unity Connection installation will fail.

Replace the hard disks:

a. Make note of the current locations of the hard disks in the server, including which hard disk is in which hard-disk slot. If the replacement fails and you want to revert to the current configuration, you must put the existing hard disks back into their current locations.

b. Remove the drive trays from the server.

c. Remove the old hard disks from the drive trays.

d. Insert the new hard disks into the drive trays.

e. Reinstall the drive trays in the locations that you made note of in Step a.

Step 4 Reattach the cover.


Configuring the Hardware

As a part of software installation, the system installer configures the system BIOS and RAID settings for the new operating system and for Cisco Unity Connection. See Table 2-6 for the BIOS settings and Table 2-7 for the RAID settings that are set up during installation.


Note If the hardware configuration process fails during installation, you can use boot-time utilities that are found on both the IBM and HP servers to manually configure the RAID and BIOS settings, as shown in Table 2-6 and Table 2-7.


Table 2-6 BIOS Configuration Settings for HP and IBM Servers 

HP Servers
IBM Servers

OS Selection: Linux (not applicable on newer models)

OS Selection: Not applicable

Boot order: CD, C:, Floppy

Boot order: CD, C:, Floppy

Post F1 prompt: Delayed

Post F1 prompt: Delayed

Hyperthreading: Enabled

Hyperthreading: Enabled


Table 2-7 RAID Settings 

MCS 7825 Servers (HP and IBM)
MCS 7835 Servers (HP and IBM)
MCS 7845 Servers (HP and IBM)

Software RAID

Logical drives: 1

Logical drives: 2

Software RAID

Note For the HP 7825H1 and the IBM 7825I1, SATA RAID is enabled, and the RAID type specifies 1(1+0), with one logical drive.

RAID type: 1(1+0)

RAID type: 1(1+0)


Verifying DNS Registration

If you use DNS, verify that all servers to be added are registered in DNS properly by performing the following actions:

Procedure


Step 1 Open a command prompt.

Step 2 To ping each server by its DNS name, enter ping DNS_name.

Step 3 To look up each server by IP address, enter nslookup IP_address.


Gathering Information for an Installation

Revised July 15, 2010

Use Table 2-8 to record the information about your server. Gather this information for a Connection server without a Connection cluster, or for each Connection server that you are installing in a cluster. You may not need to obtain all the information; gather only the information that is pertinent to your system and network configuration. You should make copies of this table and record your entries for each server in a separate table.


Note Because some of the fields are optional, they may not apply to your configuration. For example, if you choose not to set up an SMTP host during installation, the parameter still displays, but you do not need to enter a value.



Caution You cannot change some of the fields after installation without reinstalling the software, so be sure to enter the values that you want.

The last column in the table shows whether you can change a field after installation, and if you can, it provides the appropriate Command Line Interface (CLI) command.

Table 2-8 Node Configuration Data 

Parameter
Description
Can Entry Be Changed After Installation?

Administrator ID

This field specifies the administrator account user ID that you use for secure shell access to the CLI, for logging into Cisco Unified Communications Operating System Administration and for logging into the Disaster Recovery System.


Caution Do not use any of the following names for the Administrator ID, or the installation will fail:
- Operator
- Replication
- Undeliverablemessagesmailbox
- UnityConnection

No, you cannot change the entry after installation.

Note After installation, you can create additional administrator accounts, but you cannot change the original administrator account user ID.

Your entry:

Administrator Password

This field specifies the password for the Administrator account, which you use for secure shell access to the CLI, for logging into Cisco Unified Communications Operating System Administration and for logging into the Disaster Recovery System.

Ensure the password is at least six characters long; it can contain alphanumeric characters, hyphens, and underscore.

Yes, you can change the entry after installation by using the following CLI command:

CLI > set password admin

Your entry:

Application User Name

You use the Application User name as the default password for applications that are installed on the system, for example, Cisco Unity Connection Administration and Cisco Unity Connection Serviceability.


Caution Do not use any of the following names for the Application User name, or the installation will fail:
- Operator
- Replication
- Undeliverablemessagesmailbox
- UnityConnection

Yes, you can change the entry after installation by using the following CLI command:

CLI > utils reset_ui_administrator_name

Your entry:

Application User Password

You use the Application User password as the default password for applications that are installed on the system, for example, Cisco Unity Connection Administration and Cisco Unity Connection Serviceability.

Yes, you can change the entry after installation by using the following CLI command:

CLI > utils reset_ui_administrator_password

Your entry:

Country

From the list, choose the appropriate country for your installation.

Note The value you enter gets used to generate a Certificate Signing Request (CSR).

Yes, you can change the entry after installation by using the following CLI command:

CLI > set web-security

Your entry:

DHCP

If you want to use DHCP to automatically configure the network settings on your server, choose Yes.

If you choose Yes, you do not get prompted for DNS or static configuration settings.

If you choose No, you must enter a hostname, IP Address, IP Mask, and Gateway.

Yes, you can change the entry after installation by using the following CLI command:

CLI > set network dhcp

Your entry:

DNS Enable

A DNS server resolves a hostname into an IP address or an IP address into a hostname. If you do not have a DNS server, enter No.

If you have a DNS server, Cisco recommends that you enter Yes to enable DNS.

Note When DNS is not enabled, you should only enter IP addresses (not host names) for all network devices.

Yes, you can change the entry after installation by using the following CLI command:

CLI > set network dns

Your entry:

DNS Primary

Enter the IP address of the DNS server that you want to specify as the primary DNS server. Enter the IP address in dotted decimal format as ddd.ddd.ddd.ddd.

Consider this field mandatory if DNS is set to yes (DNS enabled).

Yes, you can change the entry after installation by using the following CLI command:

CLI > set network dns

Your entry:

DNS Secondary (optional)

Enter the IP address of the DNS server that you want to specify as the optional secondary DNS server.

Yes, you can change the entry after installation by using the following CLI command:

CLI > set network dns

Your entry:

Domain

This field represents the name of the domain in which this machine is located.

Consider this field mandatory if DNS is set to yes.

Yes, you can change the entry after installation by using the following CLI command:

CLI > set network domain

Your entry:

Gateway Address

Enter the IP address of the network gateway.

If you do not have a gateway, you must still set this field to 255.255.255.255. Not having a gateway may limit you to only being able to communicate with devices on your subnet.

If DHCP is set to No, consider this field mandatory.

Yes, you can change the entry after installation by using the following CLI command:

CLI > set network gateway

Your entry:

Hostname

Enter a host name that is unique to your server.

The host name can comprise up to 64 characters and can contain alphanumeric characters and hyphens.

If DHCP is set to No, consider this field mandatory.

Yes, you can change the entry after installation.

For information, see the "Renaming Cisco Unity Connection 7.x Servers" chapter of the Reconfiguration and Upgrade Guide for Cisco Unity Connection Release 7.x at http://www.cisco.com/en/US/docs/voice_ip_comm/connection/7x/upgrade/guide/7xcucrugx.html.

Your entry:

IP Address

Enter the IP address of your server.

If DHCP is set to No, consider this field mandatory.

Yes, you can change the entry after installation.

For information, see the "Changing the IP Addresses of Cisco Unity Connection 7.x Servers" chapter of the Reconfiguration and Upgrade Guide for Cisco Unity Connection Release 7.x at http://www.cisco.com/en/US/docs/voice_ip_comm/connection/7x/upgrade/guide/7xcucrugx.html.

Your entry:

IP Mask

Enter the IP subnet mask of this machine.

If DHCP is set to No, consider this field mandatory.

Yes, you can change the entry after installation by using the following CLI command:

CLI > set network ip eth0

Your entry:

Location

Choose the appropriate location for the server.

Note The value you enter gets used to generate a Certificate Signing Request (CSR).

Yes, you can change the entry after installation by using the following CLI command:

CLI > set web-security

Your entry:

MTU Size

The maximum transmission unit (MTU) represents the largest packet, in bytes, that this host will transmit on the network.

Enter the MTU size in bytes for your network. If you are unsure of the MTU setting for your network, use the default value.

Default: 1500 bytes

The MTU setting must be the same on all nodes in a cluster.

Yes, you can change the entry after installation by using the following CLI command:

CLI > set network mtu

Your entry:

NIC Duplex

Choose the duplex mode for the network interface card (NIC), either Full or Half.

Note This parameter only displays when you choose not to use Automatic Negotiation.

Yes, you can change the entry after installation by using the following CLI command:

CLI > set network nic

Your entry:

NIC Speed

Choose the speed for the NIC, either 10 megabits per second or 100 megabits per second.

Note This parameter only displays when you choose not to use Automatic Negotiation.

Yes, you can change the entry after installation by using the following CLI command:

CLI > set network nic

Your entry:

NTP Server

Enter the hostname or IP address of one or more network time protocol (NTP) servers with which you want to synchronize.

Note You can enter up to five NTP servers.

Yes, you can change the entry after installation by using the following CLI command:

CLI > utils ntp config

Your entry:

Organization

Enter the name of your organization.

Note The value you enter gets used to generate a Certificate Signing Request (CSR).

Yes, you can change the entry after installation by using the following CLI command:

CLI > set web-security

Your entry:

Security Password

Servers in the cluster use the security password to communicate with one another.

The password must contain at least six alphanumeric characters. It can contain hyphens and underscores, but it must start with an alphanumeric character.

Note Save this password. You will be asked to enter the same security password for each subsequent node in the cluster.

Yes, you can change the entry after installation by using the following CLI command:

CLI > set password security


Caution To avoid losing communications between nodes, you must change the Security password on all nodes in a cluster and reboot all of the nodes. For more information, see the description of this command in the Command Line Interface Reference Guide for Cisco Unified Communications Solutions.

Your entry:

SMTP Location

Enter the hostname or IP address for the SMTP server that is used for outbound email.

The hostname can contain alphanumeric characters, hyphens, or periods, but it must start with an alphanumeric character.

Note You must fill in this field if you plan to use electronic notification.

Yes, you can change the entry after installation by using the following CLI command:

CLI > set smtp

Your entry:

State

Enter the state where the server is located.

Note The value you enter gets used to generate a Certificate Signing Request (CSR).

Yes, you can change the entry after installation by using the following CLI command:

CLI > set web-security

Your entry:

Time Zone

This field specifies the local time zone and offset from Greenwich Mean Time (GMT).

Choose the time zone that most closely matches the location of your machine.


Caution In a cluster, the subscriber server must be configured to use the same time zone as the publisher server.

Yes, you can change the entry after installation by using the following CLI command:

CLI > set timezone

Your entry:

Unit

Enter your unit.

Note The value you enter gets used to generate a Certificate Signing Request (CSR).

Yes, you can change the entry after installation by using the following CLI command:

CLI > set password admin

Your entry:


Using the Cisco Unified Communications Answer File Generator

Cisco Unified Communications Answer File Generator, a web application, generates answer files for unattended installations of Cisco Unity Connection. Individual answer files get copied to the root directory of a USB key or a floppy diskette and are used in addition to the Cisco Unity Connection DVD during the installation process.

The web application supports the following features:

Allows simultaneous generation and saving of answer files for unattended installs on the publisher server and all subscriber servers.

Provides syntactical validation of data entries.

Provides online help and documentation.

The following usage requirements apply:

The web application supports only fresh installs and does not support upgrades.

If DHCP client is being used on the publisher server, and subscriber server answer files are also being generated, you must specify the publisher server IP address.

You can access the Cisco Unified Communications Answer File Generator at the following URL:

http://www.cisco.com/web/cuc_afg/index.html

The Cisco Unified Communications Answer File Generator supports Internet Explorer version 6.0 or higher and Mozilla version 1.5 or higher.


Note Cisco requires that you use USB keys that are compatible with Linux 2.4. Cisco recommends that you use USB keys that are preformatted to be compatible with Linux 2.4 for the configuration file. These keys will have a W95 FAT32 format.


Handling Network Errors During Installation

During the installation process, the installation program verifies that the server can successfully connect to the network by using the network configuration that you enter. If it cannot connect, a message displays, and you get prompted to select one of the following options:

RETRY —The installation program tries to validate networking again. If validation fails again, the error dialog box displays again.

REVIEW (Check Install)—This option allows you to review and modify the networking configuration. When detected, the installation program returns to the network configuration windows.

Networking gets validated after you complete each networking window, so the message might display multiple times.

HALT— The installation halts. You can copy the installation log files to a USB disk to aid troubleshooting of your network configuration.

IGNORE —The installation continues. The networking error gets logged. In some cases, the installation program validates networking multiple times, so this error dialog box might display multiple times. If you choose to ignore network errors, the installation may fail.

Installing the New Operating System and Application

This section describes how to install the operating system and the Cisco Unity Connection application. You install the operating system and application by running one installation program. This document divides the procedure for using this installation program into the following major topics:

Navigating Within the Installation Wizard

Starting the Installation

Entering Preexisting Configuration Information

Applying a Patch

Performing the Basic Installation

Configuring the First Node

Configuring a Subsequent Node

Navigating Within the Installation Wizard

For instructions on how to navigate within the installation wizard, see Table 2-9.

Table 2-9 Installation Wizard Navigation 

To Do This
Press This

Move to the next field

Tab

Move to the previous field

Alt-Tab

Choose an option

Space bar or Enter

Scroll up or down in a list

Up or down arrow

Go to the previous window

Space bar or Enter to choose Back (when available)

Get help information on a window

Space bar or Enter to choose Help (when available)


Starting the Installation

To start the installation, follow this procedure.


Note If you have a new server with the Cisco Unity Connection software preinstalled, you do not need to install from a DVD, unless you want to reimage the server with a later product release. You can go directly to the "Entering Preexisting Configuration Information" procedure.


Procedure


Step 1 If you have a USB key with configuration information that the Answer File Generator generated, insert it now.

Step 2 Insert the installation DVD into the tray and restart the server, so it boots from the DVD. After the server completes the boot sequence, the DVD Found window displays.

Step 3 To perform the media check, choose Yes or, to skip the media check, choose No.

The media check checks the integrity of the DVD. If your DVD passed the media check previously, you might choose to skip the media check.

Step 4 If you choose Yes to perform the media check, the Media Check Result window displays. Perform these tasks:

a. If the Media Check Result displays Pass, choose OK to continue the installation.

b. If the media fails the Media Check, either download another copy from Cisco.com or obtain another DVD directly from Cisco.

Step 5 The system installer performs the following hardware checks to ensure that your system is correctly configured. If the installer makes any changes to your hardware configuration settings, you will get prompted to restart your system. Leave the DVD in the drive during the reboot:

First, the installation process checks for the correct drivers, and you may see the following warning:

No hard drives have been found. You probably need to manually choose device drivers 
for install to succeed. Would you like to select drivers now?

To continue the installation, choose Yes.

The installation next checks to see whether you have a supported hardware platform. If your server does not meet the exact hardware requirements, the installation process fails with a critical error. If you think this is not correct, capture the error and report it Cisco support.

The installation process next verifies RAID configuration and BIOS settings.


Note If this step repeats, choose Yes again.


After the hardware checks complete, the Product Deployment Selection window displays.

Step 6 In the Product Deployment Selection window, select the product to install; then, choose OK. You can choose from the following options:

Cisco Unified Communications Manager

Cisco Unity Connection

Cisco Unified Communications Manager Business Edition (includes Cisco Unified Communications Manager and Cisco Unity Connection)


Note Only the products that are supported on your server appear in the list.



Note If one or more products are not supported on your server, that information also appears. If Cisco Unity Connection is listed as not supported on your server, confirm that the server meets Connection 7.x specifications. See the applicable table for your server model in the "Cisco Unity Connection Supported Servers" section of the Cisco Unity Connection Supported Platforms List at http://www.cisco.com/en/US/products/ps6509/products_data_sheets_list.html. (If a memory upgrade is required, see the "Installing a Memory Upgrade or Replacing Hard Disks (Selected Servers Only)" section before you start the installation again.)


Step 7 If software is currently installed on the server, the Overwrite Hard Drive window opens and displays the current software version on your hard drive and the version on the DVD. Choose Yes to continue with the installation or No to cancel.


Caution If you choose Yes on the Overwrite Hard Drive window, all existing data on your hard drive gets overwritten and destroyed.

The Platform Installation Wizard window displays.

Step 8 Choose the applicable option:

If Cisco Unity Connection software is already installed on the server, click Skip, and continue with the "Entering Preexisting Configuration Information" section.

If you want to perform a standard installation, click Proceed, and continue with this procedure.

If you want to perform an unattended installation, click Skip, and continue with the "Entering Preexisting Configuration Information" section. For an unattended installation, you provide preexisting configuration information on a USB key or floppy disk.

If you want to install the software now and configure it later, click Skip, and continue with the "Entering Preexisting Configuration Information" section. This installation method may take more time than other methods.

Step 9 Choose the type of installation to perform by doing the following steps.

In the Apply Additional Release window, choose one of the options:

To upgrade to a later Service Release of the software during installation, choose Yes. Continue with the "Applying a Patch" section.

To skip this step, choose No.

To return to the previous window, choose Back.

Step 10 In the Basic Install window, choose Continue to install the software version on the DVD or configure the preinstalled software. Continue with the "Performing the Basic Installation" section.


Entering Preexisting Configuration Information

Start here if you have a server that has the product preinstalled or if you chose Skip in the Platform Installation Wizard window.

Procedure


Step 1 After the system restarts, the Preexisting Installation Configuration window displays.

Step 2 If you have preexisting configuration information that the Answer File Generator created, that is stored on a floppy disc or a USB key, insert the disc or the USB key now and choose Continue. The installation wizard will read the configuration information during the installation process.


Note If a popup window states that the system detected new hardware, press any key and then choose Install from the next window.


The Platform Installation Wizard window displays.

Step 3 To continue with the Platform Installation Wizard, choose Proceed.

Step 4 Choose the type of installation to perform by doing the following steps.

In the Apply Additional Release window, choose one of the options:

To upgrade to a later Service Release of the software during installation, choose Yes. Continue with the "Applying a Patch" section.

To skip this step, choose No.

To return to the previous window, choose Back.

Step 5 In the Basic Install window, choose Continue. Continue with the "Performing the Basic Installation" section.


Applying a Patch

If you choose Yes in the Apply a Patch window, the installation wizard installs the software version on the DVD first and then restarts the system. You must obtain the appropriate upgrade file from Cisco.com before you can upgrade during installation.


Note You can upgrade to any supported higher release, so long as you have a full patch, not an ES or an SR, in which case you can only upgrade to a later service release within the same maintenance release.


You can access the upgrade file during the installation process from either a local disk (DVD) or from a remote FTP or SFTP server.

Procedure


Step 1 The Install Upgrade Retrieval Mechanism Configuration window displays.

Step 2 Choose the upgrade retrieval mechanism to use to retrieve the upgrade file:

SFTP—Retrieves the upgrade file from a remote server by using the Secure File Transfer Protocol (SFTP). Skip to the "Upgrading from a Remote Server" section.

FTP—Retrieves the upgrade file from a remote server by using File Transfer Protocol (FTP). Skip to the "Upgrading from a Remote Server" section.

LOCAL—Retrieves the upgrade file from a local DVD. Continue with the "Upgrading from a Local Disk" section.


Upgrading from a Local Disk

Before you can upgrade from a local disk, you must download the appropriate patch file from Cisco.com and use it to create an upgrade DVD. You must create an ISO image on the DVD from the upgrade file. Just copying the ISO file to a DVD will not work.

Procedure


Step 1 When the Local Patch Configuration window displays, enter the patch directory and patch name, if required, and choose OK.

The Install Upgrade Patch Selection Validation window displays.

Step 2 The window displays the patch file that is available on the DVD. To update the system with this patch, choose Continue.

Step 3 Choose the upgrade patch to install. The system installs the patch, then restarts the system with the upgraded software version running.

After the system restarts, the Preexisting Configuration Information window displays.

Step 4 To continue the installation, choose Proceed.

The Platform Installation Wizard window displays.

Step 5 To continue the installation, choose Proceed or choose Cancel to stop the installation.

If you choose Proceed, the Apply Patch window displays. Continue with Step 6.

If you choose Cancel, the system halts, and you can safely power down the server.

Step 6 When the Apply Patch window displays, choose No.

Step 7 The Windows Upgrade window displays.

Step 8 Choose No and continue with "Performing the Basic Installation" section on page 25.


Upgrading from a Remote Server

Before you can upgrade from a remote server, you must download the appropriate patch file from Cisco.com to an FTP or SFTP server that the server can access.

If you chose to upgrade through an FTP or SFTP connection to a remote server, you must first configure network settings so that the server can connect to the network.

Procedure


Step 1 The Auto Negotiation Configuration window displays.

Step 2 The installation process allows you to automatically set the speed and duplex settings of the Ethernet network interface card (NIC) by using automatic negotiation. You can change this setting after installation.


Note To use this option, your hub or Ethernet switch must support automatic negotiation.


To enable automatic negotiation, choose Yes.

The MTU Configuration window displays. Continue with Step 4.

To disable automatic negotiation, choose No. The NIC Speed and Duplex Configuration window displays. Continue with Step 3.

Step 3 If you chose to disable automatic negotiation, manually choose the appropriate NIC speed and duplex settings now and choose OK to continue.

The MTU Configuration window displays.

Step 4 In the MTU Configuration window, you can change the MTU size from the operating system default.

The maximum transmission unit (MTU) represents the largest packet, in bytes, that this host will transmit on the network. If you are unsure of the MTU setting for your network, use the default value.


Caution If you configure the MTU size incorrectly, your network performance can be affected.

To accept the default value (1500 bytes), choose No.

To change the MTU size from the operating system default, choose Yes, enter the new MTU size, and choose OK.

The DHCP Configuration window displays.

Step 5 For network configuration, you can choose to either set up static network IP addresses for the node and gateway or to use Dynamic Host Configuration Protocol (DHCP).

If you have a DHCP server that is configured in your network and want to use DHCP, choose Yes. The installation process attempts to verify network connectivity. Skip to Step 8.

If you want to configure static IP addresses for the node, choose No. The Static Network Configuration window displays.

Step 6 If you chose not to use DHCP, enter your static network configuration values and choose OK. See Table 2-8 for field descriptions.

The DNS Client Configuration window displays.

Step 7 To enable DNS, choose Yes, enter your DNS client information, and choose OK. See Table 2-8 for field descriptions.

After the system configures the network and checks for connectivity, the Remote Patch Configuration window displays.

Step 8 Enter the location and login information for the remote file server. The system connects to the remote server and retrieves a list of available upgrade patches.

If the upgrade file is located on a Linux or Unix server, you must enter a forward slash at the beginning of the directory path. For example, if the upgrade file is in the patches directory, you must enter /patches

If the upgrade file is located on a Windows server, remember that you are connecting to an FTP or SFTP server, so use the appropriate syntax, including:

Begin the path with a forward slash (/) and use forward slashes throughout the path.

The path must start from the FTP or SFTP root directory on the server, so you cannot enter a Windows absolute path, which starts with a drive letter (for example, C:).

The Install Upgrade Patch Selection window displays.

Step 9 Choose the upgrade patch to install. The system downloads, unpacks, and installs the patch and then restarts the system with the upgraded software version running.

After the system restarts, the Preexisting Configuration Information window displays.

Step 10 To continue the installation, choose Proceed.

The Platform Installation Wizard window displays.

Step 11 To continue the installation, choose Proceed or choose Cancel to stop the installation.

If you choose Proceed, the Apply Patch window displays. Continue with Step 12.

If you choose Cancel, the system halts, and you can safely power down the server.

Step 12 When the Apply Patch window displays, choose No.

Step 13 The Windows Upgrade window displays.

Step 14 Choose No and continue with the "Performing the Basic Installation" section.


Performing the Basic Installation

Revised July 15, 2010

Procedure


Step 1 When the Timezone Configuration displays, choose the appropriate time zone for the server and then choose OK.


Caution In a cluster, the subscriber server must be configured to use the same time zone as the publisher server.

The Auto Negotiation Configuration window displays.

Step 2 The installation process allows you to automatically set the speed and duplex settings of the Ethernet network interface card (NIC) by using automatic negotiation. You can change this setting after installation.

To enable automatic negotiation, choose Yes and continue with Step 5.

The MTU Configuration window displays.


Note To use this option, your hub or Ethernet switch must support automatic negotiation.


To disable automatic negotiation, choose No and continue with Step 3.

The NIC Speed and Duplex Configuration window displays.

Step 3 If you chose to disable automatic negotiation, manually choose the appropriate NIC speed and duplex settings now and choose OK to continue.

The MTU Configuration window displays.

Step 4 In the MTU Configuration window, you can change the MTU size from the operating system default.

The maximum transmission unit (MTU) represents the largest packet, in bytes, that this host will transmit on the network. If you are unsure of the MTU setting for your network, use the default value, which is 1500 bytes.


Caution If you configure the MTU size incorrectly, your network performance can be affected.

To accept the default value (1500 bytes), choose No.

To change the MTU size from the operating system default, choose Yes, enter the new MTU size, and choose OK.

The DHCP Configuration window displays.

Step 5 For network configuration, you can choose to either set up a static network IP address for the node or to use Dynamic Host Configuration Protocol (DHCP).

If you have a DHCP server that is configured in your network and want to use DHCP, choose Yes. The network restarts, and the Administrator Login Configuration window displays. Skip to Step 8.

If you want to configure a static IP address for the node, choose No. The Static Network Configuration window displays.

Step 6 If you chose not to use DHCP, enter your static network configuration values and choose OK. See Table 2-8 for field descriptions.

The DNS Client Configuration window displays.

Step 7 To enable DNS, choose Yes, enter your DNS client information, and choose OK. See Table 2-8 for field descriptions.

The network restarts by using the new configuration information, and the Administrator Login Configuration window displays.

Step 8 Enter your Administrator login and password from Table 2-8.


Note The Administrator login must start with an alphabetic character, be at least six characters long, and can contain alphanumeric characters, hyphens, and underscores. You will need the Administrator login to log in to Cisco Unified Communications Operating System Administration, the command line interface, and the Disaster Recovery System.


The Certificate Information window displays.

Step 9 Enter your certificate signing request information and choose OK.

The First Node Configuration window displays.

Step 10 You can configure this server as the first node in a Connection cluster (the publisher server), as the subsequent node (the subscriber server), or as a server without a Connection cluster.

To configure this server as the first node in a Connection cluster or as a server without a Connection cluster, choose Yes and continue with the "Configuring the First Node" section.

To configure this server as a subsequent node in the cluster, choose No and continue with the "Configuring a Subsequent Node" section.


Configuring the First Node

After you finish the basic installation, follow this procedure to configure the server as the first node in a Connection cluster (publisher server) or as a server without a Connection cluster.

Procedure


Step 1 The Network Time Protocol Client Configuration window displays.

Cisco recommends that you use an external NTP server to ensure accurate system time on the first node. Ensure the external NTP server is stratum 9 or higher (meaning stratums 1-9). Subsequent nodes in the cluster will get their time from the first node.

Step 2 Choose whether you want to configure an external NTP server or manually configure the system time.

To set up an external NTP server, choose Yes and enter the IP address, NTP server name, or NTP server pool name for at least one NTP server. You can configure up to five NTP servers, and Cisco recommends that you use at least three. Choose Proceed to continue with the installation.

The system contacts an NTP server and automatically sets the time on the hardware clock.


Note If the Test button displays, you can choose Test to check whether the NTP servers are accessible.


To manually configure the system time, choose No and enter the appropriate date and time to set the hardware clock. Choose OK to continue with the installation.

The Database Access Security Configuration window displays.

Step 3 Enter the Security password from Table 2-8.


Note The Security password must start with an alphanumeric character, be at least six characters long, and can contain alphanumeric characters, hyphens, and underscores. The system uses this password to authorize communications between nodes, and you must ensure this password is identical on all nodes in the cluster.


The SMTP Host Configuration window displays.

Step 4 If you want to configure an SMTP server, choose Yes and enter the SMTP server name.


Note You must configure an SMTP server to use certain platform features; however, you can also configure an SMTP server later by using the platform GUI or the command line interface.


Step 5 Choose OK. The Application User Configuration window displays.

Step 6 Enter the Application User name and password from Table 2-8 and confirm the password by entering it again.

Step 7 Choose OK. The Platform Configuration Confirmation window displays.

Step 8 To continue with the installation, choose OK; or to modify the platform configuration, choose Back.

The system installs and configures the software. The DVD drive ejects, and the server reboots. Do not reinsert the DVD.

Step 9 When the installation process completes, you get prompted to log in by using the Administrator account and password.

Step 10 Complete the postinstallation tasks that are listed in the "Postinstallation Tasks" section.


Configuring a Subsequent Node

To configure a subsequent node in the cluster, follow these steps.


Caution You must configure the subsequent node (subscriber server) on the first node (publisher server) by using CUC Administration before you install the subsequent node (subscriber server). See the "Configuring a Cisco Unity Connection Cluster" chapter of the Cluster Configuration and Administration Guide for Cisco Unity Connection Release 7.x.

Procedure


Step 1 If you configured Network Time Protocol on the first node, ensure that it is synchronized with an NTP server before you install a subsequent node. From the Command Line Interface on the first node, enter utils ntp status. Ensure that the output indicates that the node is synchronized with an NTP server.


Note If the first node is not synchronized with an NTP server, installation of the subsequent node will fail.


Step 2 On the First Node Configuration window, read the Warning and make sure you have correctly configured the first node. To continue with the installation of the subsequent node, click OK.

The Network Connectivity Test Configuration window displays.

Step 3 During installation of a subsequent node, the system checks to ensure that the subsequent node can connect to the first node.

To pause the installation after the system successfully verifies network connectivity, choose Yes.

To continue the installation with a pause, choose No.

The First Node Access Configuration window displays.

Step 4 Enter the first node connectivity information and choose OK.

The system checks for network connectivity.

If you chose to pause the system after the system successfully verifies network connectivity, the Successful Connection to First Node window displays. Choose Continue.


Note If the network connectivity test fails, the system always stops and allows you to go back and reenter the parameter information.


The SMTP Host Configuration window displays.

Step 5 If you want to configure an SMTP server, choose Yes and enter the SMTP server name.


Note To use certain operating system features, you must configure an SMTP server; however, you can also configure an SMTP server later by using the operating system GUI or the command line interface.


The Platform Configuration Confirmation window displays.

Step 6 To start installing the software, choose OK, or, if you want to change the configuration, choose Back.

Step 7 When the installation process completes, you get prompted to log in by using the Administrator account and password.

Step 8 Complete the postinstallation tasks that are listed in the "Postinstallation Tasks" section.


Postinstallation Tasks

After installing Cisco Unity Connection on your server, you must perform some postinstallation tasks before you can begin using it. For a list of tasks, see Table 2-10.


Note To access web applications, you must use a web browser from a computer that has network access to the Cisco Unity Connection server.


Table 2-10 Postinstallation Tasks 

Postinstallation Tasks
Important Notes

Log in as the Cisco Unity Connection Application User and change the Application User passwords.

See the "Changing the Default Application User Passwords" section.

Activate Cisco Unity Connection feature services that you want to run.

Before you activate feature services, you must perform required preactivation tasks. For service activation requirements, see the Cisco Unified Serviceability Administration Guide.

See the Cisco Unified Serviceability Administration Guide.

 

Configure the backup settings.

Remember to back up your Cisco Unity Connection data daily.

See the Disaster Recovery System Administration Guide.

If applicable, configure any network management systems in use at your site.

See the Cisco Unified Serviceability Administration Guide.


Changing the Default Application User Passwords

The installation sets all Application User passwords to the same Application User password that you entered during installation. Cisco recommends that you log in to Cisco Unity Connection Administration and change these passwords. See the System Administration Guide for Cisco Unity Connection for the procedure for changing a password.

Activating Services

Even though all services are installed on the server, you may need to use Cisco Unified Serviceability to manually activate services that you want to run. For service recommendations and more information, see Cisco Unified Serviceability Administration Guide.

Examining Log Files

If you encounter problems with the installation, you may be able to examine the install log files by entering the following commands in Command Line Interface.

To obtain a list of install log files from the command line, enter

CLI>file list install *

To view the log file from the command line, enter

CLI>file view install log_file

where log_file is the log file name.

You can also view logs by using the Real-Time Monitoring Tool. For more information on using and installing the Real-Time Monitoring Tool, see the Cisco Unified Serviceability Administration Guide.