Cisco Cius Administration Guide, Release 9.2(1)
Setting Up Cisco Cius
Downloads: This chapterpdf (PDF - 1.03MB) The complete bookPDF (PDF - 4.05MB) | Feedback

Setting Up Cisco Cius

Table Of Contents

Setting Up Cisco Cius

Before You Begin

Network Requirements

Cisco Unified Communications Manager Configuration

Understanding Cisco Cius Components

Accessory Support on Cisco Cius

USB Port and USB Serial Console Data Information

Headsets

Audio Quality Subjective to the User

Wired Headsets

Bluetooth Wireless Headsets

Advanced Audio Distribution (A2DP) Profile

Hands-Free Profile

Important Note about Headset Types

Using External Devices

Video Displays

Installing Cisco Cius

Verifying Cisco Cius Startup Process

Configuring Startup Network Settings

Configuring Security on Cisco Cius


Setting Up Cisco Cius


This chapter comprises the following topics, which help you install Cisco Cius on an IP telephony network:

Before You Begin

Understanding Cisco Cius Components

Installing Cisco Cius

Verifying Cisco Cius Startup Process

Configuring Startup Network Settings

Configuring Security on Cisco Cius


Note Before you install Cisco Cius, you must decide how to configure Cisco Cius in your network. Then you can install Cisco Cius and verify its functionality. For more information, see Chapter 2 "Preparing to Install Cisco Cius on Your Network."


Before You Begin

Before installing Cisco Cius, review the requirements in these sections:

Network Requirements

Cisco Unified Communications Manager Configuration

Network Requirements

For Cisco Cius to operate successfully as an endpoint in your network, your network must meet the following requirements:

Working Voice over IP (VoIP) Network:

VoIP configured on your Cisco routers and gateways

Cisco Unified Communications Manager installed in your network and configured to handle call processing

IP network that supports DHCP or manual assignment of IP address, gateway, and netmask


Note Cisco Cius obtains the date and time from Cisco Unified Communications Manager by default.


Voice over Wireless LAN

Cisco Aironet Access Points (APs) configured to support Voice over WLAN (VoWLAN)

Controllers and switches configured to support VoWLAN

Security implemented for authenticating wireless voice devices and users

Cisco Unified Communications Manager Configuration

Cisco Cius requires Cisco Unified Communications Manager to handle call processing. See the Cisco Unified Communications Manager Administration Guide or context-sensitive help in the Cisco Unified Communications Manager application to ensure that Cisco Unified Communications Manager is set up properly to manage Cisco Cius and to properly route and process calls.

If you plan to use auto-registration, verify that it is enabled and properly configured in Cisco Unified Communications Manager Administration before connecting any Cisco Cius to the network. For information about enabling and configuring auto-registration, see the Cisco Unified Communications Manager Administration Guide. Also, see the "Adding Cisco Cius Tablets to the Cisco Unified Communications Manager Database" section.

You must use Cisco Unified Communications Manager Administration to configure and assign telephony features to Cisco Cius tablets. See the "Telephony Features Available for Cisco Cius" section.

In Cisco Unified Communications Manager Administration, you can add users to the database and associate them with specific Cisco Cius tablets. In this way, users gain access to their Unified CM User Option page to configure options for their Cisco Cius. See the "Configuring Reset Options/Load Upgrades" section for details.

Understanding Cisco Cius Components

Cisco Cius includes these components or accessories:

Accessory Support on Cisco Cius

USB Port and USB Serial Console Data Information

Using External Devices

Video Displays

Accessory Support on Cisco Cius

Table 3-1 indicates the accessories that Cisco Cius supports.

Table 3-1 Accessory Support for Cisco Cius 

Accessory
Type

Headsets—See the "Headsets" section. This section includes information about each headset type.

Analog

3.5 mm single plug analog wideband with integrated with integrated microphone

Note RJ11 analog headsets are not supported

Bluetooth

Video Displays—See the "Video Displays" section.

External PC


USB Port and USB Serial Console Data Information

Cisco Cius includes one micro-USB port at the top of the unit. Additionally, Cisco Cius may be used with a media station, which extends the capabilities of the tablet and includes three standard USB ports, two in the back of the unit and one on the right side. Cisco Cius supports a maximum of 15 devices total connected to the USB ports. Each device that is connected to Cisco Cius is included in the maximum device count. Supported accessories include USB serial cable, USB mouse, USB keyboard, USB-powered hub, and USB memory stick.

You can also use a USB connection for Android Debug Bridge (ADB) access. For more information on using ADB, see http://developer.android.com/index.html.

For information on troubleshooting the USB Console, see the "Troubleshooting USB Console" section.

Figure 3-1 shows the front view of the media station with handset.

Figure 3-1 Media Station with Handset—Front View

Table 3-2 describes the features on the front of the media station.

Table 3-2 Media Station with Handset Features—Front View 

No.
Item
No.
Item

1

Handset

5

Speaker button

2

Speaker

6

Volume button

3

USB Port

7

Mute button

4

Docking ports

   

Figure 3-2 shows the back view of the media station with handset.

Figure 3-2 Media Station with Handset—Back View

Table 3-3 describes the features on the back of the media station.

Table 3-3 Media Station with Handset Features—Back View 

No.
Item
No.
Item

1

Antitheft security lock connector (lock optional)

5

PC port

2

Foot stand

6

DisplayPort ™ Connection

3

AC power wall plug

7

USB ports

4

Network port

8

Handset connection



Caution Avoid lowering the media station to the lowest level when using a DisplayPort cable. DisplayPort connector damage may result due to forced contact with a desk top surface. Plug the DisplayPort cable in through the hole in the foot stand to prevent the media station from being lowered to the lowest level.

The USB Serial Console allows a USB port on the media station to be used as a console, eliminating the need for a serial port.Table 3-4 shows the setting for the USB console:

Table 3-4 Terminal Settings for USB Console 

Parameter
Setting

Baud rate

115200

Data

8 bit

Parity

none

Stop

1 bit

Flow control

none



Note Because Cisco Cius comes preloaded with drivers, Cisco supports only a limited number of cable types. Cisco recommends using IOGEAR USB-serial adapter.


The USB console cable has a USB interface on one end and a serial interface on the other. The USB interface may be plugged in to any of the three USB ports on Cisco Cius. The serial interface connects to the serial port on the PC.


Tip If you do not have a serial port on your PC/laptop, two USB console cables can be connected back to back, with a Null modem cable between them.


To use a USB console, use the following procedure.

Procedure


Step 1 In Cisco Unified Communications Manager, set credentials on device page.

Step 2 Enable "USB debugging" under Product Specific Configuration window.

Step 3 Connect a USB serial cable to Cisco Cius. Cisco Cius console output appears on your terminal screen.

Step 4 After output stops, tap <Return> to sign in.

Step 5 Sign in as default using default password. See Table 9-1 for password information.

Step 6 After $ prompt screen, you can use tools such as debugsh to diagnose Cisco Cius problems.


For information on troubleshooting the USCB console, see the "Troubleshooting USB Console" section.

Headsets

Although Cisco performs internal testing of third-party headsets for use with Cisco Cius, Cisco does not certify or support products from headset or handset vendors.

Cisco Cius reduces some background noise that is detected by a headset microphone, but if you want to further reduce the background noise and improve the overall audio quality, use a noise-canceling headset.

Cisco recommends the use of good-quality external devices, for example, headsets that are screened against unwanted radio frequency (RF) and audio frequency (AF) signals. Depending on the quality of headsets and their proximity to other devices such as mobile (cell) phones and two-way radios, some noise or echo may still occur. A hum or buzz may be heard either by the remote party or by both the remote party and Cisco Cius user. Humming or buzzing sounds can be caused by a range of outside sources; for example, electric lights, electric motors, or large PC monitors. See the "Using External Devices" section, for more information.


Note In some cases, you can reduce or eliminate hum by using a local power cube or power injector.


These environmental and hardware inconsistencies in the locations where Cisco Cius are deployed means that there is not a single headset solution that is optimal for all environments.

Cisco recommends that customers test headsets in their intended environment to determine performance before making a purchasing decision and deploying them system wide.

Audio Quality Subjective to the User

Beyond the physical, mechanical, and technical performance, the audio portion of a headset must sound good to the user and to the party on the far end. Sound quality is subjective and Cisco cannot guarantee the performance of any headsets. However, a variety of headsets from leading headset manufacturers are reported to perform well with Cisco devices. See manufacturer sites for details.

Wired Headsets

Cisco Cius supports 3.5 mm single plug headsets. To connect a wired headset to Cisco Cius, plug it in to the headset port on the bottom of Cisco Cius to place and answer calls using the headset. Single plug wired headsets may also be plugged into the headset port, located on the left side of the media station.

You can use the wired headset with all of the features on Cisco Cius, including the Volume and Mute buttons. Use these buttons to adjust the earpiece volume and to mute the speech path from the headset microphone.

If the headset is analog, see the for the procedure on configuring the wideband codec.

Bluetooth Wireless Headsets

Cisco Cius supports Bluetooth Version 2.1+EDR technology when the headsets support Bluetooth. Bluetooth enables low-bandwidth wireless connections within a range of 30 feet (10 meters). The best performance is in the 3- to 6-foot range (1 to 2 meters). You can pair five or more headsets, but only the last one connected is used as the default.

There can be a potential interference issues. Cisco recommends that you reduce the proximity of other 802.11b/g devices, Bluetooth devices, microwave ovens, and large metal objects. If possible, configure other 802.11 devices to use the 802.11a channels.

For a Bluetooth wireless headset to work, it does not need to be within direct line-of-sight of the Cisco Cius tablet, but some barriers, such as walls or doors, and interference from other electronic devices could affect the connection.

Adding a Bluetooth Wireless Headset to Cisco Cius

By default, Bluetooth is enabled for Cisco Cius on the Cisco Unified Communications Manager.


Note To disable Bluetooth from the Cisco Unified Communications Manager, choose Device > Phone. In the Find and List Phones window, enter the search criteria for the Cisco Cius tablet that you want to modify, and then select Find. On the Product Specific Configuration Layout portion of the Phone Configuration window, scroll down to Bluetooth, click on the Down Arrow and select Disabled.


With Bluetooth enabled on the Cisco Unified Communications Manager, follow these steps to add the headset as an accessory to Cisco Cius:

Procedure


Step 1 Place the headset into discovery/pairing mode.


Note The procedure for placing a headset into discovery/pairing mode is specific to the headset. Please see headset manufacturer's instructions regarding pairing procedure.



Note The headset must be in discovery/pairing mode for Cisco Cius to successfully pair and connect to the device.


Step 2 Enable Bluetooth and Bluetooth settings on Cisco Cius, if they are not already enabled. To verify whether Bluetooth and Bluetooth settings are enabled, from Cisco Cius Main Screen, Press the Menu key and choose Settings > Wireless & networks > Bluetooth settings.


Note You can tell that the Bluetooth wireless headset is enabled if there is a check mark next to "Bluetooth" in the Bluetooth Settings dialog box.



Note If Airplane Mode is enabled, then the Bluetooth and Bluetooth settings are disabled.


Step 3 Select Scan for devices.

After the Bluetooth device is located, its name appears in the window.

Cisco Cius automatically tries to pair with the headset by using a PIN of "0000." If the headset uses a different PIN, enter the correct PIN by referring to the user guide that came with the headset.


Note Cisco recommends that users read the headset user guide for more information about pairing and connecting the headsets.



Note If pairing is unsuccessful, Cisco Cius prompts you to enter the correct PIN.



After Cisco Cius has the correct PIN, it tries to connect to the accessory. Cisco Cius provides feedback to the user while it is trying to connect the accessory. If Cisco Cius cannot connect, it displays an error alert to let the user know the reason for the failure. A timeout of 10 seconds occurs for the Cisco Cius tablet to try to connect the accessory. If the timer expires without a successful connection, an error alert is shown.

Cisco Cius connects with headsets using a shared key authentication and encryption method. Cisco Cius can be connected with five or more headsets at a time. The last one connected is used as the default. Pairing is typically performed once for each headset.

After a device has been paired, its Bluetooth connection is maintained as long as both devices (Cisco Cius and headset) are enabled and within range of each other. The connection typically reestablishes itself automatically if either of the devices powers down and then powers up. However, some headsets require user action to reestablish the connection.

The Bluetooth status indicator indicates whether or not a device is connected.

When headset is out of range from the Cisco Cius, Bluetooth drops the connection after a 15- to 20-second timeout. If the paired headset comes back into range of Cisco Cius (and Cisco Cius is not connected to another Bluetooth headset), the in-range Bluetooth headset automatically reconnects. The user may have to "wake-up" the headset by tapping on its operational button to begin the reconnect process.

If a user is actively on a call using a Bluetooth headset, and the headset is set to off, out-of-range, or is disconnected for any reason, an alert is presented to either continue the call on the speaker/headset or disconnect the call. If no action is taken by the user after 30 seconds, the call is ended.

Removing a Bluetooth Device From the Cisco Cius Tablet

To remove a Bluetooth device from Cisco Cius, follow these steps:

Procedure


Step 1 From the home screen, Press the Menu key and choose Settings > Wireless & networks > Bluetooth settings.

Step 2 Tap Device name.

Step 3 Highlight the device you want to remove and hold that selection until the options appear.

Step 4 Tap Disconnect or Disconnect and Unpair.


Related Documentation About Bluetooth Wireless Headsets

For information about how to use your Bluetooth wireless headset, see:

Cisco Cius User Guide

User guide provided with your headset

Advanced Audio Distribution (A2DP) Profile

Cisco Cius supports A2DP streaming audio from a music player to a Bluetooth headset that supports A2DP. A2DP can be disabled by the user. From the Bluetooth devices submenu, select the connected headset and choose Options > Disable A2DP.

Hands-Free Profile

Cisco Cius supports various hands-free profile features that enable you to use hands-free devices (such as Bluetooth wireless headsets) to perform certain tasks without having to handle the Cisco Cius tablet. For example, instead of tapping Redial on Cisco Cius, users can redial a number from their Bluetooth wireless headset according to instructions from the headset manufacturer.

These typical hands-free features apply to Bluetooth wireless headsets that are used with Cisco Cius:

Ring notification

Answer a call

End a call

Volume control

Last number redial

Call waiting notification

Divert/Reject

Three-way call handling

Speed dialing

Hands-Free devices may differ in how features are activated. Device manufacturers may also use different terms when referring to the same feature.

For more information, see the manufacturer documentation.

Important Note about Headset Types

Only one headset type works at any given time, so if you have both a Bluetooth headset and an analog headset attached to the Cisco Cius tablet, enabling the Bluetooth headset disables the analog headset. To enable the analog headset, disable the Bluetooth headset.

Using External Devices

Cisco recommends the use of good-quality external devices that are shielded (screened) against unwanted radio frequency (RF) and audio frequency (AF) signals.

Depending on the quality of these devices and their proximity to other devices such as mobile phones or two-way radios, some audio noise may still occur. In these cases, Cisco recommends that you take one or more of the following actions:

Move the external device away from the source of the RF or AF signals.

Route the external device cables away from the source of the RF or AF signals.

Use shielded cables for the external device, or use cables with a better shield and connector.

Shorten the length of the external device cable.

Apply ferrites or other such devices on the cables for the external device.

Cisco cannot guarantee the performance of the system because Cisco has no control over the quality of external devices, cables, and connectors. The system performs adequately when suitable devices are attached using good-quality cables and connectors.


Caution In European Union countries, use only external headsets that are fully compliant with EMC Directive 89/336/EC.

Video Displays

Cisco Cius supports external display devices through the micro-HDMI port on the bottom of the tablet. Connect a monitor to the tablet by inserting one end of an HDMI cable into the micro-HDMI port and the other end into a monitor HDMI port.

Installing Cisco Cius

You must connect Cisco Cius to the network and to a power source before using it. Cisco Cius can be powered directly through the AC Adapter on Cisco Cius or through Power over Ethernet (PoE+ 802.3at) through the media station.

Before using external devices, read the "Using External Devices" section for safety and performance information.


Note Before you install a Cisco Cius tablet, it must be added to Cisco Unified Communications Manager. For more information, see the "Adding Cisco Cius Tablets to the Cisco Unified Communications Manager Database" section. Make sure you upgrade Cisco Cius to the current firmware image.



Note Firmware upgrades over the WLAN interface may take longer than upgrading over the wired interface, depending on the quality and bandwidth of the wireless connection. Some upgrades may take more than one hour.


To install Cisco Cius, you must perform the tasks in Table 3-5.

Table 3-5 Installing Cisco Cius 

Task
Related Topics

Connect Cisco Cius to external power through the AC adaptor CP-PWR-CUBE 4.

(Optional) Connect Cisco Cius to Power over Ethernet (PoE+ 802.3at) through the media station.

Note Cisco Cius requires either AC adaptor CP-PWR-CUBE 4 or PoE+ (802.3at) power. With PoE+, media station will be operational. Accessories that are plugged in to the media station, such as mouse or keyboard, will negotiate for power. If not enough power is available for the accessory, an error message will appear on the Cisco Cius screen.

See the Cisco Cius User Guide for information.

Charge Cisco Cius.

See the Cisco Cius User Guide for information.

Connect a headset to the headset port.

(Optional) You can add a headset later if you do not connect one now.

See the Cisco Cius User Guide and the user guide provided with your headset for information.

(Optional) Enable Cisco Cius to use the wireless local area network (WLAN).

See the "Configuring Wireless LAN" section and the "Wireless & Network Settings Menu" section.

Configure Network Settings.

See "TFTP Server Settings Menu" section.

Configure features.

See the Cisco Cius User Guide for information.


Related Topics

Verifying Cisco Cius Startup Process

Configuring Startup Network Settings

Verifying Cisco Cius Startup Process

After Cisco Cius is charged, press the Power button at the top of the unit to start the tablet. Cisco Cius begins its startup diagnostic process as the tablet checks its hardware. The home screen cycles through two screens, the first displays "Cisco Cius" and the second a flashing blue Cisco logo. The Cisco Cius then boots to the unlock screen with the clock, missed-call calendar and voicemail count icons, and swipe-to-unlock arrow.

If Cisco Cius successfully passes through these stages, it has started up properly. If Cisco Cius does not start up properly, the Cisco Unified Communications Manager will show the tablet as unregistered and and Cisco Cius will display the unregistered icon (red "X") at the top left of the status bar. In addition, when the user opens the phone application, the user will see a message that the tablet is not registered. For information on resolving startup problems, see the "General Troubleshooting" section.

Configuring Startup Network Settings

If you are not using DHCP in your network, you must configure these network settings on Cisco Cius after installing it on the network:

IP address

Gateway

Netmask

Domain name

TFTP server IP address

You also may configure the DNS server settings, if necessary.

Collect this information and see the instructions in Chapter 6 "Configuring Settings on Cisco Cius."

Configuring Security on Cisco Cius

The security features protect against several threats, including threats to the identity of Cisco Cius and to data. These features establish and maintain authenticated communication streams between Cisco Cius and the Cisco Unified Communications Manager server, and ensure that Cisco Cius uses only digitally signed files. Data on the Cisco Cius tablet itself is protected by an Encrypted File System.

Cisco Unified Communications Manager (beginning with Release 8.5(1)) includes Security by Default, which provides the following security features for Cisco Cius tablets without running the CTL client:

Signing of Cisco Cius configuration files

Cisco Cius configuration file encryption

HTTPS with Tomcat and other web services


Note Secure signaling and media features still require you to run the CTL client and use hardware eTokens.


For more information about the security features, see the "Understanding Security Features for Cisco Cius" section. Also, see the Cisco Unified Communications Manager Security Guide.

A Locally Significant Certificate (LSC) is installed on Cisco Cius after you perform the necessary tasks that are associated with the Certificate Authority Proxy Function (CAPF). You can use Cisco Unified Communications Manager Administration to configure an LSC, as described in the Cisco Unified Communications Manager Security Guide.

Alternatively, you can initiate the installation of an LSC from the Enterprise Security Settings menu on Cisco Cius. This menu also lets you update or remove an LSC.

Before You Begin

Make sure that the appropriate Cisco Unified Communications Manager and the CAPF security configurations are complete. See the Cisco Unified Communications Manager Security Guide and the Cisco Cius Wireless LAN Deployment Guide for more information.

To configure an LSC on Cisco Cius, perform these steps:

Procedure


Step 1 Obtain the CAPF authentication code that was set after the CAPF was configured.

Step 2 From the home screen on Cisco Cius, choose Applications Menu > Settings > Location & security > Enterprise security settings.

Step 3 Tap LSC.

Cisco Cius prompts for an authentication string.

Step 4 Enter the authentication string if required by administrator and tap Submit.


Note Cisco Cius restarts after LSC is installed, upgraded, or deleted.


Cisco Cius begins to install, update, or remove the LSC, depending on how the CAPF was configured. During the procedure, a series of messages appears in the LSC option field in the Security Configuration menu, so you can monitor progress. After the procedure is completed successfully, Cisco Cius displays Installed or Not Installed.

The LSC installation, update, or removal process can take a long time to complete. You can stop the process at any time by tapping Cancel.

After the installation procedure is completed successfully, Cisco Cius indicates "Installed." If Cisco Cius indicates "Not Installed," the authorization string may be incorrect or Cisco Cius may not enabled for upgrading. If the CAPF operation deletes the LSC, Cisco Cius indicates "Not Installed" to indicate that the operation was successful. See error messages generated on the CAPF server and take appropriate actions.