Getting Started Guide for Cisco UCS E-Series Servers, Release 1.0
Cisco IOS Software Command Reference
Downloads: This chapterpdf (PDF - 391.0KB) The complete bookPDF (PDF - 3.66MB) | Feedback

Cisco IOS Software Command Reference

Cisco IOS Software Command Reference

This chapter lists the Cisco IOS commands used to configure the host router and the E-Series Server.

For details about each command, such as command history, usage guidelines, and examples, see the Cisco IOS Interface and Hardware Component Command Reference at http://www.cisco.com/en/US/docs/ios-xml/ios/interface/command/ir-cr-book.html.

This chapter includes the following sections:

Password Reset Command

Commands

Description

ucse slot password-reset {BIOS | BMC}

Resets the BIOS, CIMC, or RAID password.

  • slot—Router slot number in which the E-Series Server is installed.
  • BIOS—Resets the BIOS password.
  • BMC—Resets the CIMC password.

Session Command

Commands

Description

ucse slot session {imc [clear] | host [clear]}

Starts or closes a session with the host E-Series Server or with CIMC.

  • slot—Router slot number in which the E-Series Server is installed.
  • imc—Starts a session with CIMC.
  • imc clear—Clears the existing CIMC session.
  • host—Starts a session with the host E-Series Server.
  • host clear—Clears the host E-Series Server session.
Note   

If serial-over-LAN is enabled in CIMC, the session host command will not display any output.

IP Address Configuration Commands

Commands

Description

imc ip address ip_address subnet_mask default-gateway gateway_address

no imc ip address ip_address subnet_mask default-gateway gateway_address

Configures a static IP address for CIMC and the IP address of the default gateway router that CIMC must use.

  • ip_address —IP address of CIMC.
  • subnet_mask—Subnet mask to append to the IP address; must be in the same subnet as the host router.
  • gateway_address—IP address of the default gateway router.

imc ip address dhcp

no imc ip address dhcp

Configures a dynamic IP address for CIMC.

CIMC Access Commands

Commands

Description

imc access-port {dedicated | shared-lom [GE1 | GE2 | GE3 | console | failover [option]}

no imc access-port {dedicated | shared-lom [GE1 | GE2 | GE3 | console | failover [option]}

Configures CIMC access through the E-Series Server’s dedicated or shared LOM ports.

  • dedicated—Configures CIMC access using the Management (dedicated) port.
  • shared-lom—Configures CIMC access using one of the following shared LOM ports:
    • GE1
    • GE2
    • GE1
    • console
    • failover
  • option—If you enter failover, you must also enter one of the additional parameters:
    • GE1 GE1 [GE2] | [GE3] [GE2 GE3]
    • GE2 GE2 GE3

VLAN Command

Commands

Description

imc vlan vlan_number

no imc vlan

Enters VLAN configuration mode for the specified VLAN.

Reload, Reset, Start, Stop, Shutdown Commands

Commands

Description

ucse slot reload

Gracefully shuts down the E-Series Server and then powers it on.

  • slot—Router slot number in which the E-Series Server is installed.

ucse slot reset

Resets the hardware on the E-Series Server.

  • slot—Router slot number in which the E-Series Server is installed.

ucse slot start

Powers on the E-Series Server.

  • slot—Router slot number in which the E-Series Server is installed.

ucse slot stop

Powers down the E-Series Server immediately.

  • slot—Router slot number in which the E-Series Server is installed.

ucse slot shutdown

Gracefully shuts down the E-Series Server.

  • slot—Router slot number in which the E-Series Server is installed.

Statistics and Status Commands

Commands

Description

ucse slot statistics [clear]

Displays or clears the reset and reload information of the E-Series Server.

  • slot—Router slot number in which the E-Series Server is installed.
  • clear—Clears the E-Series Server's reset and reload information.

ucse slot status [detailed]

Displays configuration information related to the hardware and software on the E-Series Server.

  • slot—Router slot number in which the E-Series Server is installed.
  • detailed—Displays detail information about the E-Series Server, such as the status of the server and settings of the reset and heartbeat-reset flags.

Boot Commands

Commands

Description

ucse slot cmos-reset

Resets the BIOS CMOS of the E-Series Server.

  • slot—Router slot number in which the E-Series Server is installed.