Catalyst 3750 Switch Software Configuration Guide, Cisco IOS Release 15.0(2)SE and Later
Preface
Downloads: This chapterpdf (PDF - 67.0KB) The complete bookPDF (PDF - 14.04MB) | Feedback

Table of Contents

Preface

Audience

Purpose

Conventions

Related Publications

Obtaining Documentation, Obtaining Support, and Security Guidelines

Preface

Audience

This guide is for the networking professional managing the Catalyst 3750 switch, hereafter referred to as the switch . Before using this guide, you should have experience working with the Cisco IOS software and be familiar with the concepts and terminology of Ethernet and local area networking.

Purpose

The Catalyst 3750 switch is supported by either the IP base image or the IP services image. The IP base image provides Layer 2+ features including access control lists (ACLs), quality of service (QoS), static routing, EIGRP stub routing, and the Routing Information IP services image provides a richer set of enterprise-class features. It includes Layer 2+ features and full Layer 3 routing (IP unicast routing, IP multicast routing, and fallback bridging). To distinguish it from the Layer 2+ static routing and RIP, the IP services image includes protocols such as the Enhanced Interior Gateway Routing Protocol (EIGRP) and the Open Shortest Path First (OSPF) Protocol.

 

This guide provides procedures for using the commands that have been created or changed for use with the switch. It does not provide detailed information about these commands. For detailed information about these commands, see the Catalyst 3750 Switch Command Reference for this release. For information about the standard Cisco IOS Release 15.0 commands, see the Cisco IOS documentation set available on Cisco.com.

This guide does not provide detailed information on the graphical user interfaces (GUIs) for the embedded device manager or for Cisco Network Assistant (hereafter referred to as Network Assistant) that you can use to manage the switch. However, the concepts in this guide are applicable to the GUI user. For information about the device manager, see the switch online help. For information about Network Assistant, see Getting Started with Cisco Network Assistant , available on Cisco.com.

This guide does not describe system messages you might encounter or how to install your switch. For more information, see the appropriate system message guide and hardware installation guide.

For documentation updates, see the release notes for this release.

Conventions

This publication uses these conventions to convey instructions and information:

Command descriptions use these conventions:

  • Commands and keywords are in boldface text.
  • Arguments for which you supply values are in italic .
  • Square brackets ([ ]) mean optional elements.
  • Braces ({ }) group required choices, and vertical bars ( | ) separate the alternative elements.
  • Braces and vertical bars within square brackets ([{ | }]) mean a required choice within an optional element.

Interactive examples use these conventions:

  • Terminal sessions and system displays are in screen font.
  • Information you enter is in boldface screen font.
  • Nonprinting characters, such as passwords or tabs, are in angle brackets (< >).

Notes, cautions, and timesavers use these conventions and symbols:


Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.



Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Related Publications

These documents provide complete information about the switch and are available from this Cisco.com site:
http://www.cisco.com/en/US/products/hw/switches/ps5023/tsd_products_support_series_home.html


Note Before installing, configuring, or upgrading the switch, see these documents:

  • For initial configuration information, see the “Using Express Setup” section in the getting started guide or the “Configuring the Switch with the CLI-Based Setup Program” appendix in the hardware installation guide.
  • For device manager requirements, see the “System Requirements” section in the release notes (not orderable but available on Cisco.com).
  • For Network Assistant requirements, see the Getting Started with Cisco Network Assistant (not orderable but available on Cisco.com).
  • For cluster requirements, see the Release Notes for Cisco Network Assistant (not orderable but available on Cisco.com).
  • For upgrading information, see the “Downloading Software” section in the release notes.


 

See these documents for other information about the switch:

  • Release Notes for the Catalyst 3750, 3560, 3560-C, 2960, 2960-S, and 2960- C Switches
  • Catalyst 3750, 3560, 3550, 2975, 2975, 2970, and 2960 and 2960-S Switch System Message Guide
  • Catalyst 3750 Switch Software Configuration Guide
  • Catalyst 3750 Switch Command Reference
  • Catalyst 3750 Switch Hardware Installation Guide
  • Catalyst 3750 Switch Getting Started Guide
  • Regulatory Compliance and Safety Information for the Catalyst 3750 Switch
  •  
  •  
  • Catalyst 3750, 3560, 2960, and 2960-S Switch System Message Guide
  • Auto Smartports Configuration Guide
  • Call Home Configuration Guide
  • Cisco EnergyWise Configuration Guide
  • Smart Install Configuration Guide
  • Release Notes for Cisco Network Assistant
  • Getting Started with Cisco Network Assistant
  • Cisco CWDM GBIC and CWDM SFP Installation Note
  • Cisco RPS 300 Redundant Power System Hardware Installation Guide
  • Cisco RPS 675 Redundant Power System Hardware Installation Guide
  • Cisco Redundant Power System 2300 Hardware Installation Guide
  • For information about the Network Admission Control (NAC) features, see the Network Admission Control Software Configuration Guide
  • Information about Cisco SFP, SFP+, and GBIC modules is available from this Cisco.com site:
    http://www.cisco.com/en/US/products/hw/modules/ps5455/prod_installation_guides_list.html

SFP compatibility matrix documents are available from this Cisco.com site:
http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html

Obtaining Documentation, Obtaining Support, and Security Guidelines

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation , which also lists all new and revised Cisco technical documentation:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.