Catalyst 3560 Switch Software Configuration Guide, Rel. 12.1(19)EA1
Overview
Downloads: This chapterpdf (PDF - 339.0KB) The complete bookPDF (PDF - 10.12MB) | Feedback

Overview

Table Of Contents

Overview

Features

Default Settings After Initial Switch Configuration

Network Configuration Examples

Design Concepts for Using the Switch

Small to Medium-Sized Network Using Catalyst 3560 Switches

Large Network Using Catalyst 3560 Switches

Long-Distance, High-Bandwidth Transport Configuration

Where to Go Next


Overview


This chapter provides these topics about the Catalyst 3560 switch software:

Features

Default Settings After Initial Switch Configuration

Network Configuration Examples

Where to Go Next

In this document, IP refers to IP version 4 (IPv4).

Features

The Catalyst 3560 switches are shipped with either of these software images installed:

Standard multilayer image (SMI), which provides Layer 2+ features (enterprise-class intelligent services). These features include access control lists (ACLs), quality of service (QoS), static routing, and the Hot Standby Router Protocol (HSRP) and the Routing Information Protocol (RIP). Switches with the SMI installed can be upgraded to the EMI.

Enhanced multilayer image (EMI), which provides a richer set of enterprise-class intelligent services. It includes all SMI features plus full Layer 3 routing (IP unicast routing, IP multicast routing, and fallback bridging). To distinguish it from the Layer 2+ static routing and RIP, the EMI includes protocols such as the Enhanced Interior Gateway Routing Protocol (EIGRP) and the Open Shortest Path First (OSPF) Protocol.

EMI-only features are noted in the "Layer 3 Features" section.


Note Unless otherwise noted, all features described in this chapter and in this guide are supported on both the SMI and EMI.


Some features noted in this chapter are available only on the cryptographic (that is, supports encryption) versions of the SMI and EMI. You must obtain authorization to use this feature and to download the cryptographic version of the software from Cisco.com. For more information, refer to the release notes for this release.

The Catalyst 3560 switches have these features:

Ease-of-Use and Ease-of-Deployment Features

Performance Features

Management Options

Manageability Features (includes a feature requiring the cryptographic [that is, supports encryption] versions of the SMI and EMI)

Availability Features

VLAN Features

Security Features (includes a feature requiring the cryptographic [that is, supports encryption] versions of the SMI and EMI)

QoS and CoS Features

Layer 3 Features (includes features requiring the EMI)

Power over Ethernet (PoE) Features

Monitoring Features

Ease-of-Use and Ease-of-Deployment Features   

Express Setup for quickly configuring a switch for the first time with basic IP information, contact information, switch and Telnet passwords, and Simple Network Management Protocol (SNMP) information through a browser-based program

User-defined SmartPort macros for creating custom switch configurations for simplified deployment across the network

Cluster Management Suite (CMS) graphical user interface (GUI) for

Simplifying and minimizing switch and switch cluster management through a supported web browser from anywhere in your intranet.

Accomplishing multiple configuration tasks from a single CMS window without needing to remember command-line interface (CLI) commands to accomplish specific tasks.

Interactive guide mode that guides you in configuring complex features such as VLANs, ACLs, and quality of service (QoS).

Automated configuration wizards that prompt you to provide only the minimum required information to configure complex features such as QoS priorities for video traffic, priority levels for data applications, and security.

Applying actions to multiple ports and multiple switches at the same time, such as VLAN and QoS settings, inventory and statistic reports, link- and switch-level monitoring and troubleshooting, and multiple switch software upgrades.

Viewing a topology of interconnected devices to identify existing switch clusters and eligible switches that can join a cluster and to identify link information between switches.

Monitoring real-time status of a switch or multiple switches from the LEDs on the front-panel images. The system, redundant power system (RPS), and port LED colors on the images are similar to those used on the physical LEDs.

Switch clustering technology for

Unified configuration, monitoring, authentication, and software upgrade of multiple, cluster-capable switches, regardless of their geographic proximity and interconnection media, including Ethernet, Fast Ethernet, Fast EtherChannel, small form-factor pluggable (SFP) modules, Gigabit Ethernet, and Gigabit EtherChannel connections. Refer to the release notes for a list of cluster-capable switches.

Automatic discovery of candidate switches and creation of clusters of up to 16 switches that can be managed through a single IP address.

Extended discovery of cluster candidates that are not directly connected to the command switch.

Performance Features

Autosensing of port speed and autonegotiation of duplex mode on all switch ports for optimizing bandwidth

Automatic-medium-dependent interface crossover (Auto-MDIX) capability on 10/100 Mbps interfaces and on 10/100/1000 BASE-T/TX SFP interfaces that enables the interface to automatically detect the required cable connection type (straight-through or crossover) and to configure the connection appropriately

IEEE 802.3X flow control on all ports (the switch does not send pause frames)

EtherChannel for enhanced fault tolerance and for providing up to 8 Gbps (Gigabit EtherChannel) or 800 Mbps (Fast EtherChannel) full duplex of bandwidth between switches, routers, and servers

Port Aggregation Protocol (PAgP) and Link Aggregation Control Protocol (LACP) for automatic creation of EtherChannel links

Forwarding of Layer 2 and Layer 3 packets at Gigabit line rate

Per-port storm control for preventing broadcast, multicast, and unicast storms

Port blocking on forwarding unknown Layer 2 unknown unicast, multicast, and bridged broadcast traffic

Cisco Group Management Protocol (CGMP) server support and Internet Group Management Protocol (IGMP) snooping for IGMP versions 1, 2, and 3:

(For CGMP devices) CGMP for limiting multicast traffic to specified end stations and reducing overall network traffic

(For IGMP devices) IGMP snooping for efficiently forwarding multimedia and multicast traffic

IGMP report suppression for sending only one IGMP report per multicast router query to the multicast devices (supported only for IGMPv1 or IGMPv2 queries)

Multicast VLAN registration (MVR) to continuously send multicast streams in a multicast VLAN while isolating the streams from subscriber VLANs for bandwidth and security reasons

IGMP filtering for controlling the set of multicast groups to which hosts on a switch port can belong

IGMP throttling for configuring the action when the maximum number of entries is in the IGMP forwarding table

Switch Database Management (SDM) templates for allocating system resources to maximize support for user-selected features

Management Options

CMS—CMS is a GUI that can be launched from anywhere in your network through a web browser such as Netscape Communicator or Microsoft Internet Explorer. CMS is already installed on the switch. For more information about CMS, see "Getting Started with CMS."

CLI—The Cisco IOS CLI software is enhanced to support desktop- and multilayer-switching features. You can access the CLI either by connecting your management station directly to the switch console port or by using Telnet from a remote management station. For more information about the CLI, see "Using the Command-Line Interface."

SNMP—SNMP management applications such as CiscoWorks2000 LAN Management Suite (LMS) and HP OpenView. You can manage from an SNMP-compatible management station that is running platforms such as HP OpenView or SunNet Manager. The switch supports a comprehensive set of MIB extensions and four remote monitoring (RMON) groups. For more information about using SNMP, see "Configuring SNMP."

Manageability Features


Note The encrypted Secure Shell (SSH) feature listed in this section is available only on the cryptographic (that is, supports encryption) versions of the SMI and EMI.


Dynamic Host Configuration Protocol (DHCP) for automating configuration of switch information (such as IP address, default gateway, host name, and Domain Name System [DNS] and Trivial File Transfer Protocol (TFTP) server names)

DHCP relay for forwarding User Datagram Protocol (UDP) broadcasts, including IP address requests, from DHCP clients

DHCP server for automatic assignment of IP addresses and other DHCP options to IP hosts

Directed unicast requests to a DNS server for identifying a switch through its IP address and its corresponding host name and to a TFTP server for administering software upgrades from a TFTP server

Address Resolution Protocol (ARP) for identifying a switch through its IP address and its corresponding Media Access Control (MAC) address

Unicast MAC address filtering to drop packets with specific source or destination MAC addresses

Cisco Discovery Protocol (CDP) versions 1 and 2 for network topology discovery and mapping between the switch and other Cisco devices on the network

Network Time Protocol (NTP) for providing a consistent time stamp to all switches from an external source

Cisco IOS File System (IFS) for providing a single interface to all file systems that the switch uses

In-band management access through CMS over a Netscape Communicator or Microsoft Internet Explorer browser session

In-band management access for up to 16 simultaneous Telnet connections for multiple CLI-based sessions over the network

In-band management access for up to five simultaneous, encrypted Secure Shell (SSH) connections for multiple CLI-based sessions over the network (requires the cryptographic [that is, supports encryption] versions of the SMI and EMI)

In-band management access through SNMP versions 1 and 2c, and 3 get and set requests

Out-of-band management access through the switch console port to a directly attached terminal or to a remote terminal through a serial connection or a modem


Note For additional descriptions of the management interfaces, see the "Network Configuration Examples" section.


Availability Features

HSRP for command switch and Layer 3 router redundancy

UniDirectional Link Detection (UDLD) and aggressive UDLD for detecting and disabling unidirectional links on fiber-optic interfaces caused by incorrect fiber-optic wiring or port faults

IEEE 802.1D Spanning Tree Protocol (STP) for redundant backbone connections and loop-free networks. STP has these features:

Up to 128 spanning-tree instances supported

Per-VLAN spanning-tree plus (PVST+) for balancing load across VLANs

Rapid PVST+ for balancing load across VLANs and providing rapid convergence of spanning-tree instances

UplinkFast and BackboneFast for fast convergence after a spanning-tree topology change and for achieving load balancing between redundant uplinks, including Gigabit uplinks

IEEE 802.1S Multiple Spanning Tree Protocol (MSTP) for grouping VLANs into a spanning-tree instance and for providing multiple forwarding paths for data traffic and load balancing and IEEE 802.1W Rapid Spanning Tree Protocol (RSTP) for rapid convergence of the spanning tree by immediately transitioning root and designated ports to the forwarding state

Optional spanning-tree features available in PVST+, rapid-PVST+, and MSTP mode:

Port Fast for eliminating the forwarding delay by enabling a port to immediately transition from the blocking state to the forwarding state

BPDU guard for shutting down Port Fast-enabled ports that receive bridge protocol data units (BPDUs)

BPDU filtering for preventing a Port Fast-enabled port from sending or receiving BPDUs

Root guard for preventing switches outside the network core from becoming the spanning-tree root

Loop guard for preventing alternate or root ports from becoming designated ports because of a failure that leads to a unidirectional link

Equal-cost routing for link-level and switch-level redundancy

RPS support through the Cisco RPS 300 and Cisco RPS 675 for enhancing power reliability

VLAN Features

Support for up to 1005 VLANs for assigning users to VLANs associated with appropriate network resources, traffic patterns, and bandwidth

Support for VLAN IDs in the full 1 to 4094 range allowed by the IEEE 802.1Q standard

VLAN Query Protocol (VQP) for dynamic VLAN membership

Inter-Switch Link (ISL) and IEEE 802.1Q trunking encapsulation on all ports for network moves, adds, and changes; management and control of broadcast and multicast traffic; and network security by establishing VLAN groups for high-security users and network resources

Dynamic Trunking Protocol (DTP) for negotiating trunking on a link between two devices and for negotiating the type of trunking encapsulation (802.1Q or ISL) to be used

VLAN Trunking Protocol (VTP) and VTP pruning for reducing network traffic by restricting flooded traffic to links destined for stations receiving the traffic

Voice VLAN for creating subnets for voice traffic from Cisco IP Phones

VLAN1 minimization for reducing the risk of spanning-tree loops or storms by allowing VLAN 1 to be disabled on any individual VLAN trunk link. With this feature enabled, no user traffic is sent or received on the trunk. The switch CPU continues to send and receive control protocol frames.

Security Features


Note The Kerberos feature listed in this section is available only on the cryptographic (that is, supports encryption) versions of the SMI and EMI.


Password-protected access (read-only and read-write access) to management interfaces (CMS and CLI) for protection against unauthorized configuration changes

Multilevel security for a choice of security level, notification, and resulting actions

Static MAC addressing for ensuring security

Protected port option for restricting the forwarding of traffic to designated ports on the same switch

Port security option for limiting and identifying MAC addresses of the stations allowed to access the port

Port security aging to set the aging time for secure addresses on a port

BPDU guard for shutting down a Port Fast-configured port when an invalid configuration occurs

Standard and extended IP access control lists (ACLs) for defining security policies in both directions on routed interfaces (router ACLs) and VLANs and inbound on Layer 2 interfaces (port ACLs)

Extended MAC access control lists for defining security policies in the inbound direction on Layer 2 interfaces

VLAN ACLs (VLAN maps) for providing intra-VLAN security by filtering traffic based on information in the MAC, IP, and TCP/User Datagram Protocol (UDP) headers

Source and destination MAC-based ACLs for filtering non-IP traffic

DHCP snooping to filter untrusted DHCP messages between untrusted hosts and DHCP servers

IEEE 802.1X port-based authentication to prevent unauthorized devices (clients) from gaining access to the network

802.1X with VLAN assignment for restricting 802.1X-authenticated users to a specified VLAN

802.1X with port security for controlling access to 802.1X ports

802.1X with voice VLAN to permit an IP phone access to the voice VLAN regardless of the authorized or unauthorized state of the port

802.1X with guest VLAN to provide limited services to non-802.1X-compliant users

Terminal Access Controller Access Control System Plus (TACACS+), a proprietary feature for managing network security through a TACACS server

Remote Authentication Dial-In User Service (RADIUS) for verifying the identity of, granting access to, and tracking the actions of remote users through authentication, authorization, and accounting (AAA) services

Kerberos security system to authenticate requests for network resources by using a trusted third party (requires the cryptographic [that is, supports encryption] versions of the SMI and EMI)

QoS and CoS Features

Automatic QoS (auto-QoS) to simplify the deployment of existing QoS features by classifying traffic and configuring egress queues (voice over IP only)

Classification

IP type-of-service/Differentiated Services Code Point (IP TOS/DSCP) and 802.1P CoS marking priorities on a per-port basis for protecting the performance of mission-critical applications

IP TOS/DSCP and 802.1P CoS marking based on flow-based packet classification (classification based on information in the MAC, IP, and TCP/UDP headers) for high-performance quality of service at the network edge, allowing for differentiated service levels for different types of network traffic and for prioritizing mission-critical traffic in the network

Trusted port states (CoS, DSCP, and IP precedence) within a QoS domain and with a port bordering another QoS domain

Trusted boundary for detecting the presence of a Cisco IP phone, trusting the CoS value received, and ensuring port security

Policing

Traffic-policing policies on the switch port for managing how much of the port bandwidth should be allocated to a specific traffic flow

Aggregate policing for policing traffic flows in aggregate to restrict specific applications or traffic flows to metered, predefined rates

Out-of-Profile

Out-of-profile markdown for packets that exceed bandwidth utilization limits

Ingress queueing and scheduling

Two configurable ingress queues for user traffic (one queue can be the priority queue)

Weighted tail drop (WTD) as the congestion-avoidance mechanism for managing the queue lengths and providing drop precedences for different traffic classifications

Shaped round robin (SRR) as the scheduling service for determining the rate at which packets are dequeued to the internal ring (sharing is the only supported mode on ingress queues)

Egress queues and scheduling

Four egress queues per port

WTD as the congestion-avoidance mechanism for managing the queue lengths and providing drop precedences for different traffic classifications

SRR as the scheduling service for determining the rate at which packets are dequeued to the egress interface (shaping or sharing is supported on egress queues). Shaped egress queues are guaranteed but limited to using a share of port bandwidth. Shared egress queues are also guaranteed a configured share of bandwidth, but can use more than the guarantee if other queues become empty and do not use their share of the bandwidth.

Layer 3 Features


Note Some features noted in this section are available only on the EMI.


HSRP for Layer 3 router redundancy

IP routing protocols for load balancing and for constructing scalable, routed backbones:

RIP versions 1 and 2

OSPF (requires the EMI)

Interior Gateway Routing Protocol (IGRP) and Enhanced IGRP (EIGRP) (requires the EMI)

Border Gateway Protocol (BGP) Version 4 (requires the EMI)

IP routing between VLANs (inter-VLAN routing) for full Layer 3 routing between two or more VLANs, allowing each VLAN to maintain its own autonomous data-link domain

Policy-based routing (PBR) for configuring defined policies for traffic flows

Fallback bridging for forwarding non-IP traffic between two or more VLANs (requires the EMI)

Static IP routing for manually building a routing table of network path information

Equal-cost routing for load balancing and redundancy

Internet Control Message Protocol (ICMP) and ICMP Router Discovery Protocol (IRDP) for using router advertisement and router solicitation messages to discover the addresses of routers on directly attached subnets

Protocol-Independent Multicast (PIM) for multicast routing within the network, allowing for devices in the network to receive the multicast feed requested and for switches not participating in the multicast to be pruned. Includes support for PIM sparse mode (PIM-SM), PIM dense mode (PIM-DM), and PIM sparse-dense mode. (requires the EMI)

Multicast Source Discovery Protocol (MSDP) for connecting multiple PIM-SM domains (requires the EMI)

Distance Vector Multicast Routing Protocol (DVMRP) tunnelling for interconnecting two multicast-enabled networks across non-multicast networks (requires the EMI)

DHCP relay for forwarding UDP broadcasts, including IP address requests, from DHCP clients

Power over Ethernet (PoE) Features

Ability to provide power to connected Cisco pre-standard and IEEE 802.3af-compliant powered devices from all 10/100 Ethernet ports if the switch senses that there is no power on the circuit

24-port PoE switch provides 15.4 W of power on each 10/100 port; 48-port PoE switch provides 15.4 W of power to any 24 of the 48 10/100 ports, or any combination of ports provide an average of 7.7 W of power at the same time, up to a maximum switch power output of 370 W

Automatic detection and power budgeting; the switch maintains a power budget, monitors and tracks requests for power, and grants power only when it is available

Monitoring Features

Switch LEDs that provide port- and switch-level status

MAC address notification traps and RADIUS accounting for tracking users on a network by storing the MAC addresses that the switch has learned or removed

Switched Port Analyzer (SPAN) and Remote SPAN (RSPAN) for traffic monitoring on any port or VLAN

SPAN and RSPAN support of Intrusion Detection Systems (IDS) to monitor, repel, and report network security violations

Four groups (history, statistics, alarms, and events) of embedded RMON agents for network monitoring and traffic analysis

Syslog facility for logging system messages about authentication or authorization errors, resource issues, and time-out events

Layer 2 traceroute to identify the physical path that a packet takes from a source device to a destination device

Default Settings After Initial Switch Configuration

The switch is designed for plug-and-play operation, requiring only that you assign basic IP information to the switch and connect it to the other devices in your network. If you have specific network needs, you can change the interface-specific and system-wide settings.

If you do not configure the switch at all, the switch operates with the default settings listed in Table 1-1. This table lists the key software features, their defaults, and where to find more information about the features.

For information about setting up the initial switch configuration (using Express Setup or the CLI setup program) and assigning basic IP information to the switch, refer to the hardware installation guide.

Table 1-1 Default Settings After Initial Switch Configuration 

Feature
Default Setting
More information in...

Switch IP address, subnet mask, and default gateway

0.0.0.0

"Assigning the Switch IP Address and Default Gateway"

Domain name

None

DHCP

DHCP client enabled

Switch cluster

Disabled

"Clustering Switches"

Passwords

None defined

"Administering the Switch"

TACACS+

Disabled

RADIUS

Disabled

System name and prompt

Switch

NTP

Enabled

DNS

Enabled

802.1X

Disabled

"Configuring 802.1X Port-Based Authentication"

Port parameters
 

Operating mode

Layer 2 (switchport)

"Configuring Interface Characteristics"

Interface speed and duplex mode

Autonegotiate

Auto-MDIX

Disabled

Flow control

Off

 

Power over Ethernet (PoE)

Auto

 

SmartPort macros

None defined

"Configuring SmartPort Macros"

VLANs
 

Default VLAN

VLAN 1

"Configuring VLANs"

VLAN trunking

Dynamic auto (DTP)

Trunk encapsulation

Negotiate

VTP mode

Server

"Configuring VTP"

VTP version

1

Voice VLAN

Disabled

"Configuring Voice VLAN"

STP

PVST+ enabled on VLAN 1

"Configuring STP"

MSTP

Disabled

"Configuring MSTP"

Optional spanning-tree features

Disabled

"Configuring Optional Spanning-Tree Features"

DHCP snooping
 

DHCP snooping

Disabled

"Configuring DHCP Features"

DHCP snooping information option

Enabled

IGMP snooping
 

IGMP snooping

Enabled

"Configuring IGMP Snooping and MVR"

IGMP filters

None applied

 

IGMP throttling

Deny

MVR

Disabled

Port-based Traffic
 

Broadcast, multicast, and unicast storm control

Disabled

"Configuring Port-Based Traffic Control"

Protected ports

None defined

Unicast and multicast traffic flooding

Not blocked

Secure ports

None configured

CDP

Enabled

"Configuring CDP"

UDLD

Disabled

"Configuring UDLD"

SPAN and RSPAN

Disabled

"Configuring SPAN and RSPAN"

RMON

Disabled

"Configuring RMON"

Syslog messages

Enabled; displayed on the console

"Configuring System Message Logging"

SNMP

Enabled; version 1

"Configuring SNMP"

ACLs

None configured

"Configuring Network Security with ACLs"

QoS

Disabled

"Configuring QoS"

EtherChannels

None configured

"Configuring EtherChannels"


Network Configuration Examples

This section provides network configuration concepts and includes examples of using the switch to create dedicated network segments and interconnecting the segments through Fast Ethernet and Gigabit Ethernet connections.

"Design Concepts for Using the Switch" section

"Small to Medium-Sized Network Using Catalyst 3560 Switches" section

"Large Network Using Catalyst 3560 Switches" section

"Long-Distance, High-Bandwidth Transport Configuration" section

Design Concepts for Using the Switch

As your network users compete for network bandwidth, it takes longer to send and receive data. When you configure your network, consider the bandwidth required by your network users and the relative priority of the network applications they use.

Table 1-2 describes what can cause network performance to degrade and how you can configure your network to increase the bandwidth available to your network users.

Table 1-2 Increasing Network Performance

Network Demands
Suggested Design Methods

Too many users on a single network segment and a growing number of users accessing the Internet

Create smaller network segments so that fewer users share the bandwidth, and use VLANs and IP subnets to place the network resources in the same logical network as the users who access those resources most.

Use full-duplex operation between the switch and its connected workstations.

Increased power of new PCs, workstations, and servers

High bandwidth demand from networked applications (such as e-mail with large attached files) and from bandwidth-intensive applications (such as multimedia)

Connect global resources—such as servers and routers to which the network users require equal access—directly to the high-speed switch ports so that they have their own high-speed segment.

Use the EtherChannel feature between the switch and its connected servers and routers.


Bandwidth alone is not the only consideration when designing your network. As your network traffic profiles evolve, consider providing network services that can support applications for voice and data integration, multimedia integration, application prioritization, and security. Table 1-3 describes some network demands and how you can meet them.

Table 1-3 Providing Network Services 

Network Demands
Suggested Design Methods

Efficient bandwidth usage for multimedia applications and guaranteed bandwidth for critical applications

Use IGMP snooping to efficiently forward multimedia and multicast traffic.

Use other QoS mechanisms such as packet classification, marking, scheduling, and congestion avoidance to classify traffic with the appropriate priority level, thereby providing maximum flexibility and support for mission-critical, unicast, and multicast and multimedia applications.

Use optional IP multicast routing to design networks better suited for multicast traffic.

Use MVR to continuously send multicast streams in a multicast VLAN but to isolate the streams from subscriber VLANs for bandwidth and security reasons.

High demand on network redundancy and availability to provide always on mission-critical applications

Use Hot Standby Router Protocol (HSRP) for cluster command switch and router redundancy.

Use VLAN trunks and BackboneFast for traffic-load balancing on the uplink ports so that the uplink port with a lower relative port cost is selected to carry the VLAN traffic.

An evolving demand for IP telephony

Use QoS to prioritize applications such as IP telephony during congestion and to help control both delay and jitter within the network.

Use switches that support at least two queues per port to prioritize voice and data traffic as either high- or low-priority, based on 802.1P/Q. The Catalyst 3560 switch supports at least four queues per port.

Use voice VLAN IDs (VVIDs) to provide separate VLANs for voice traffic.

A growing demand for using existing infrastructure to transport data and voice from a home or office to the Internet or an intranet at higher speeds

Use the Catalyst Long-Reach Ethernet (LRE) switches to provide up to 15 Mb of IP connectivity over existing infrastructure, such as existing telephone lines.

Note LRE is the technology used in the Catalyst 2900 LRE XL and Catalyst 2950 LRE switches. Refer to the documentation sets specific to these switches for LRE information.


Small to Medium-Sized Network Using Catalyst 3560 Switches

Figure 1-1 shows a configuration for a network of up to 500 employees. This network uses Catalyst 3560 Layer 3 switches with high-speed connections to two routers. For network reliability and load balancing, this network has HSRP enabled on the routers and on the switches. This ensures connectivity to the Internet, WAN, and mission-critical network resources in case one of the routers or switches fails. The switches are using routed uplinks for faster failover. They are also configured with equal-cost routing for load sharing and redundancy.

The switches are connected to workstations, local servers, and IEEE 802.3af compliant and noncompliant powered devices (such as Cisco IP Phones). The server farm includes a call-processing server running Cisco CallManager software. Cisco CallManager controls call processing, routing, and IP phone features and configuration. The switches are interconnected through Gigabit interfaces.

This network uses VLANs to logically segment the network into well-defined broadcast groups and for security management. Data and multimedia traffic are configured on the same VLAN. Voice traffic from the Cisco IP Phones are configured on separate VVIDs. If data, multimedia, and voice traffic are assigned to the same VLAN, only one VLAN can be configured per wiring closet.

When an end station in one VLAN needs to communicate with an end station in another VLAN, a router or Layer 3 switch routes the traffic to the appropriate destination VLAN. In this network, the switches are providing inter-VLAN routing. VLAN access control lists (VLAN maps) on the switches provide intra-VLAN security and prevent unauthorized users from accessing critical pieces of the network.

In addition to inter-VLAN routing, the multilayer switches provide QoS mechanisms such as DSCP priorities to prioritize the different types of network traffic and to deliver high-priority traffic in a predictable manner. If congestion occurs, QoS drops low-priority traffic to allow delivery of high-priority traffic.

For pre-standard and IEEE 802.3af-compliant powered devices connected to Catalyst Power over Ethernet (PoE) switches, 802.1P/Q QoS gives voice traffic forwarding-priority over data traffic.

Catalyst PoE switch ports automatically detect any Cisco pre-standard and IEEE 802.3af-compliant powered devices that are connected. Each PoE switch port provides 15.4 W of power per port. The powered device, such as an IP phone, can receive redundant power when it is also connected to an AC power source. Powered devices not connected to Catalyst PoE switches must be connected to AC power sources to receive power.

Cisco CallManager controls call processing, routing, and IP phone features and configuration. Users with workstations running Cisco SoftPhone software can place, receive, and control calls from their PCs. Using Cisco IP Phones, Cisco CallManager software, and Cisco SoftPhone software integrates telephony and IP networks, and the IP network supports both voice and data.

With the multilayer switches providing inter-VLAN routing and other network services, the routers focus on firewall services, Network Address Translation (NAT) services, voice-over-IP (VoIP) gateway services, and WAN and Internet access.

Figure 1-1 Catalyst 3560 Switches in a Collapsed Backbone Configuration

Large Network Using Catalyst 3560 Switches

Switches in the wiring closet have traditionally been Layer 2-only devices, but as network traffic profiles evolve, switches in the wiring closet are increasingly employing multilayer services such as multicast management and traffic classification. Figure 1-2 shows a configuration for a network only using Catalyst 3560 multilayer switches in the wiring closets and two backbone switches, such as the Catalyst 6500 switches, to aggregate up to ten wiring closets.

In the wiring closet, each switch has IGMP snooping enabled to efficiently forward multimedia and multicast traffic. QoS ACLs that either drop or mark nonconforming traffic based on bandwidth limits are also configured on each switch. VLAN maps provide intra-VLAN security and prevent unauthorized users from accessing critical pieces of the network. QoS features can limit bandwidth on a per-port or per-user basis. The switch ports are configured as either trusted or untrusted. You can configure a trusted port to trust the CoS value, the DSCP value, or the IP precedence. If you configure the port as untrusted, you can use an ACL to mark the frame in accordance with the network policy.

Each switch provides inter-VLAN routing. They provide proxy ARP services to determine IP and MAC address mapping, thereby removing this task from the routers and decreasing this type of traffic on the WAN links. These switches also have redundant uplink connections to the backbone switches, with each uplink port configured as a trusted routed uplink to provide faster convergence in case of an uplink failure.

The routers and backbone switches have HSRP enabled for load balancing and redundant connectivity to guarantee mission-critical traffic.

Figure 1-2 Catalyst 3560 Switches in Wiring Closets in a Backbone Configuration

Long-Distance, High-Bandwidth Transport Configuration

Figure 1-3 shows a configuration for sending 8 Gigabits of data over a single fiber-optic cable. The Catalyst 3560 switches have Coarse Wave Division Multiplexer (CWDM) fiber-optic SFP modules installed. Depending on the CWDM SFP module, data is sent at wavelengths from 1470 to 1610 nm. The higher the wavelength, the farther the transmission can travel. A common wavelength used for long-distance transmissions is 1550 nm.

The CWDM SFP modules connect to CWDM optical add/drop multiplexer (OADM) modules over distances of up to 393,701 feet (74.5 miles or 120 km). The CWDM OADM modules combine (or multiplex) the different CWDM wavelengths, allowing them to travel simultaneously on the same fiber-optic cable. The CWDM OADM modules on the receiving end separate (or demultiplex) the different wavelengths.

For more information about the CWDM SFP modules and CWDM OADM modules, refer to the Cisco CWDM GBIC and CWDM SFP Installation Note.

Figure 1-3 Long-Distance, High-Bandwidth Transport Configuration

Where to Go Next

Before configuring the switch, review these sections for startup information:

"Using the Command-Line Interface"

"Getting Started with CMS"

"Assigning the Switch IP Address and Default Gateway"