Cisco Nexus 6000 Series NX-OS SAN Switching Configuration Guide, Release 7.x
Distributing Device Alias Services
Downloads: This chapterpdf (PDF - 1.38MB) The complete bookPDF (PDF - 5.95MB) | The complete bookePub (ePub - 1.77MB) | Feedback

Distributing Device Alias Services

Distributing Device Alias Services

This chapter describes how to distribute device alias services.

This chapter contains the following sections:

Distributing Device Alias Services

Cisco SAN switches support Distributed Device Alias Services (device aliases) on a fabric-wide basis.

Information About Device Aliases

Cisco SAN switches support Distributed Device Alias Services (device aliases) on a fabric-wide basis.

When the port WWN (pWWN) of a device must be specified to configure features (for example, zoning, DPVM, or port security) in a Cisco SAN switch, you must assign the correct device name each time you configure these features. An inaccurate device name may cause unexpected results. You can circumvent this problem if you define a user-friendly name for a pWWN and use this name in all the configuration commands as required. These user-friendly names are referred to as device aliases.

Device Alias Features

Device aliases have the following features:

  • The device alias information is independent of the VSAN configuration.
  • The device alias configuration and distribution is independent of the zone server and the zone server database.
  • You can import legacy zone alias configurations without losing data.
  • The device alias application uses the Cisco Fabric Services (CFS) infrastructure to enable efficient database management and distribution. Device aliases use the coordinated distribution mode and the fabric-wide distribution scope.
  • Basic and enhanced modes.
  • Device aliases used to configure zones, IVR zones, or port security features are displayed automatically with their respective pWWNs in the show command output.

For additional information, refer to Using Cisco Fabric Services in the System Management Configuration Guide for your device.

Related Concepts

Device Alias Requirements

Device aliases have the following requirements:

  • You can only assign device aliases to pWWNs.
  • There must be a one-to-one relationship between the pWWN and the device alias that maps to it.
  • A device alias name is restricted to 64 alphanumeric characters and may include one or more of the following characters:
    • a to z and A to Z
    • Device alias names must begin with an alphabetic character (a to z or A to Z).
    • 1 to 9
    • - (hyphen) and _ (underscore)
    • $ (dollar sign) and ^ (up caret)

Zone Aliases Versus Device Aliases

The following table compares the configuration differences between zone-based alias configuration and device alias configuration.

Table 1  Comparison Between Zone Aliases and Device Aliases

Zone-Based Aliases

Device Aliases

Aliases are limited to the specified VSAN.

You can define device aliases without specifying the VSAN number. You can also use the same definition in one or more VSANs without any restrictions.

Zone aliases are part of the zoning configuration. The alias mapping cannot be used to configure other features.

Device aliases can be used with any feature that uses the pWWN.

You can use any zone member type to specify the end devices.

Only pWWNs are supported.

Configuration is contained within the zone server database and is not available to other features.

Device aliases are not restricted to zoning. Device alias configuration is available to the FCNS, zone, fcping, and traceroute applications.

Device Alias Databases

The device alias feature uses two databases to accept and implement device alias configurations.

  • Effective database—The database currently used by the fabric.
  • Pending database—Your subsequent device alias configuration changes are stored in the pending database.

If you modify the device alias configuration, you need to commit or discard the changes as the fabric remains locked during this period.

Device alias database changes are validated with the applications. If any of the applications cannot accept the device alias database changes, then those changes are rejected; this applies to device alias database changes resulting from either a commit or merge operation.

Creating Device Aliases

You can create a device alias in the pending database.

Procedure
     Command or ActionPurpose
    Step 1configure terminal


    Example:
    switch# configure terminal
    switch(config)#
     

    Enters global configuration mode.

     
    Step 2 device-alias database


    Example:
    switch(config)# device-alias database
    switch(config-device-alias-db)#
     

    Enters the pending database configuration submode.

     
    Step 3 device-alias name device-name pwwn pwwn-id


    Example:
    switch(config-device-alias-db)# device-alias name mydevice pwwn 21:01:00:e0:8b:2e:80:93
     

    Specifies a device name for the device that is identified by its pWWN. Starts writing to the pending database and simultaneously locks the fabric as this is the first-issued device alias configuration command.

     
    Step 4 no device-alias name device-name


    Example:
    switch(config-device-alias-db)# no device-alias name mydevice
     

    Removes the device name for the device that is identified by its pWWN.

     
    Step 5 device-alias rename old-device-name new-device-name


    Example:
    switch(config-device-alias-db)# device-alias rename mydevice mynewdevice
     

    Renames an existing device alias with a new name.

     
    EXAMPLES

    This example shows how to display the device alias configuration.

    switch# show device-alias name x
    
    device-alias name x pwwn 21:01:00:e0:8b:2e:80:93

    Device Alias Modes

    You can specify that aliases operate in basic or enhanced modes.

    When operating in basic mode, which is the default mode, the device alias is immediately expanded to a pWWN. In basic mode, when device aliases are changed to point to a new HBA, for example, that change is not reflected in the zone server. Users must remove the previous HBA’s pWWN, add the new HBA’s pWWN, and then reactivate the zoneset.

    When operating in enhanced mode, applications accept a device alias name in its native format. Instead of expanding the device alias to a pWWN, the device alias name is stored in the configuration and distributed in its native device alias format. So applications such as zone server, PSM, or DPVM can automatically keep track of the device alias membership changes and enforce them accordingly. The primary benefit of operating in enhanced mode is that you have a single point of change.

    Whenever you change device alias modes, the change is distributed to other switches in the network only if device alias distribution is enabled or on. Otherwise, the mode change only takes place on the local switch.


    Note


    Enhanced mode, or native device alias-based configurations, are not accepted in interop mode VSANs. IVR zoneset activation fails in interop mode VSANs if the corresponding zones have native device alias-based members.


    Device Alias Mode Guidelines and Limitations for Device Alias Services

    Device Alias services have these configuration guidelines and limitations:

    • If two fabrics running in different device alias modes are joined together, the device alias merge fails. There is no automatic conversion to one mode or the other during the merge process. In this situation, you must select one mode over the other.
    • Before changing from enhanced to basic mode, you must first explicitly remove all native device alias-based configurations from both local and remote switches, or replace all device alias-based configuration members with the corresponding pWWN.
    • If you remove a device alias from the device alias database, all applications automatically stop enforcing the corresponding device alias. If that corresponding device alias is part of an active zone set, all the traffic to and from that pWWN is disrupted.
    • Renaming the device alias not only changes the device alias name in the device alias database, but also replaces the corresponding device alias configuration in all of the applications.
    • When a new device alias is added to the device alias database, and the application configuration is present on that device alias, it automatically takes effect. For example, if the corresponding device alias is part of the active zoneset and the device is online, then zoning is enforced automatically. You do not have to reactivate the zone set.
    • If a device alias name is mapped to a new HBA’s pWWN, the application’s enforcement changes accordingly. In this case, the zone server automatically enforces zoning based on the new HBA’s pWWN.

    Configuring Device Alias Modes

    You can configure device aliases to operate in enhanced mode.

    Procedure
       Command or ActionPurpose
      Step 1configure terminal


      Example:
      switch# configure terminal
      switch(config)#
       

      Enters global configuration mode.

       
      Step 2 device-alias mode enhanced


      Example:
      switch(config)# device-alias mode enhanced
       

      Assigns the device alias to operate in enhanced mode.

       
      Step 3 no device-alias mode enhance


      Example:
      switch(config)# no device-alias mode enhance 
       

      Assigns the device alias to operate in basic mode.

       
      EXAMPLES

      This example shows how to display the current device alias mode setting.

      switch# show device-alias status
      
      Fabric Distribution: Enabled
      Database:- Device Aliases 0 Mode: Basic
      Locked By:- User "admin" SWWN 20:00:00:0d:ec:30:90:40
      Pending Database:- Device Aliases 0 Mode: Basic

      Device Alias Distribution

      By default, device alias distribution is enabled. The device alias feature uses CFS to distribute the modifications to all switches in a fabric.

      If device alias distribution is disabled, database changes are not distributed to the switches in the fabric. The same changes would have to be performed manually on all switches in the fabric to keep the device alias database up-to-date. Database changes immediately take effect, so there would also not be any pending database and commit or abort operations. If you have not committed the changes and you disable distribution, a commit task fails.

      This example shows how to display a failed device alias status:

      switch# show device-alias status
      
      Fabric Distribution: Disabled
      Database:- Device Aliases 25
      Status of the last CFS operation issued from this switch:
      ==========================================================
      Operation: Commit
      Status: Failed (Reason: Operation is not permitted as the fabric distribution is
       currently disabled.)

      Locking the Fabric

      When you perform any device alias configuration task (regardless of which device alias task), the fabric is automatically locked for the device alias feature. Once you lock the fabric, the following situations apply:

      • No other user can make any configuration changes to this feature.
      • A copy of the effective database is obtained and used as the pending database. Subsequent modifications are made to the pending database. The pending database remains in use until you commit the modifications to the pending database or discard (abort) the changes to the pending database.

      Committing Changes

      You can commit changes.

      If you commit the changes made to the pending database, the following events occur:

      • The pending database content overwrites the effective database content.
      • The pending database is distributed to the switches in the fabric and the effective database on those switches is overwritten with the new changes.
      • The pending database is emptied of its contents.
      • The fabric lock is released for this feature.
      Procedure
         Command or ActionPurpose
        Step 1configure terminal


        Example:
        switch# configure terminal
        switch(config)#
         

        Enters global configuration mode.

         
        Step 2 device-alias commit


        Example:
        switch(config)# device-alias commit
         

        Commits the changes made to the currently active session.

         

        Discarding Changes

        You can discard the device alias session changes.

        If you discard the changes made to the pending database, the following events occur:

        • The effective database contents remain unaffected.
        • The pending database is emptied of its contents.
        • The fabric lock is released for this feature.
        Procedure
           Command or ActionPurpose
          Step 1configure terminal


          Example:
          switch# configure terminal
          switch(config)#
           

          Enters global configuration mode.

           
          Step 2 device-alias abort


          Example:
          switch(config)# device-alias abort
           

          Discards the currently active session.

           
          EXAMPLES

          This example shows how to display the status of the discard operation:

          switch# show device-alias status
          
          Fabric Distribution: Enabled
          Database:- Device Aliases 24
          Status of the last CFS operation issued from this switch:
          ==========================================================
          Operation: Abort
          Status: Success

          Overriding the Fabric Lock

          You can use locking operations (clear, commit, abort) only when device alias distribution is enabled. If you have performed a device alias task and have forgotten to release the lock by either committing or discarding the changes, an administrator can release the lock from any switch in the fabric. If the administrator performs this task, your changes to the pending database are discarded and the fabric lock is released.

          The changes are only available in the volatile directory and may be discarded if the switch is restarted.

          To use administrative privileges and release a locked device alias session, use the clear device-alias session command in EXEC mode.

          switch# clear device-alias session
          

          This example shows how to display the status of the clear operation:

          switch# show device-alias status
          
          Fabric Distribution: Enabled
          Database:- Device Aliases 24
          Status of the last CFS operation issued from this switch:
          ==========================================================
          Operation: Clear Session<--------------------Lock released by administrator
          
          Status: Success<-----------------------------Successful status of the operation
          

          Disabling and Enabling Device Alias Distribution

          You can disable or enable the device alias distribution.

          Procedure
             Command or ActionPurpose
            Step 1configure terminal


            Example:
            switch# configure terminal
            switch(config)#
             

            Enters global configuration mode.

             
            Step 2 no device-alias distribute


            Example:
            switch(config)# no device-alias distribute
             

            Disables the distribution.

             
            Step 3 device-alias distribute


            Example:
            switch(config)# device-alias distribute
             

            Enables the distribution (default).

             
            EXAMPLES

            This example shows how to display the status of device alias distribution:

            switch# show device-alias status
            
            Fabric Distribution: Enabled <-------------------------------Distribution is enabled 
            Database:-Device Aliases 24 
            Locked By:-User "Test" SWWN 20:00:00:0c:cf:f4:02:83<-Lock holder's user name and switch ID 
            Pending Database:- Device Aliases 24 
            Status of the last CFS operation issued from this switch: 
            ========================================================== 
            Operation: Enable Fabric Distribution 
            Status: Success 

            This example shows the device alias display when distribution is disabled:

            switch# show device-alias status
            
            Fabric Distribution: Disabled 
            Database:- Device Aliases 24 
            Status of the last CFS operation issued from this switch: 
            ========================================================== 
            Operation: Disable Fabric Distribution 
            Status: Success 

            Legacy Zone Alias Configuration

            You can import legacy zone alias configurations to use this feature without losing data if they satisfy the following restrictions:

            • Each zone alias has only one member.
            • The member type is pWWN.

            If any name or definition conflict exists, the zone aliases are not imported.

            Ensure that you copy any required zone aliases to the device alias database as required by your configuration.

            When an import operation is complete, the modified alias database is distributed to all other switches in the physical fabric when you perform the commit operation. If you do not want to distribute the configuration to other switches in the fabric, you can perform the abort operation and the merge changes are completely discarded.

            Importing a Zone Alias

            You can import the zone alias for a specific VSAN.

            Procedure
               Command or ActionPurpose
              Step 1configure terminal


              Example:
              switch# configure terminal
              switch(config)#
               

              Enters global configuration mode.

               
              Step 2 device-alias import fcalias vsan vlan-id


              Example:
              switch(config)# device-alias import fcalias vsan 
               

              Imports the fcalias information for the specified VSAN.

               

              Device Alias Database Merge Guidelines

              When merging two device alias databases, follow these guidelines:

              • Verify that two device aliases with different names are not mapped to the same pWWN.
              • Verify that two identical pWWNs are not mapped to two different device aliases.
              • Verify that the combined number of device aliases in both databases does not exceed 8K (8191 device aliases) in fabrics running Cisco MDS SAN-OS Release 3.0 (x) and earlier, and 20K in fabrics running Cisco MDS SAN-OS Release 3.1(x) and later.

              If the combined number of device entries in both databases exceeds the supported configuration limit, then the merge will fail. For example, if database N has 6000 device aliases and database M has 2192 device aliases, and you are running SAN-OS Release 3.0(x) or earlier, then this merge operation will fail. Merge operations will also fail if there is a device alias mode mismatch.

              For additional information, refer to CFS Merge Support in the System Management Configuration Guide for your device.

              Verifying the Device Alias Configuration

              To display device alias information, perform one of the following tasks:

              Command Purpose
              show zoneset [active] Displays the device aliases in the zone set information.
              show device-alias database [pending | pending-diffs] Displays the device alias database.
              show device-alias {pwwn pwwn-id | name device-name } [pending] Displays the device alias information for the specified pwwn or alias.
              show flogi database [pending] Displays device alias information in the flogi database.
              show fcns database [pending] Displays device alias information in the fcns database.

              Default Settings for Device Alias Services

              The following table lists the default settings for device alias parameters.

              Table 2  Default Device Alias Parameters

              Parameters

              Default

              Device alias distribution

              Enabled.

              Device alias mode

              Basic.

              Database in use

              Effective database.

              Database to accept changes

              Pending database.

              Device alias fabric lock state

              Locked with the first device alias task.