Cisco Nexus 6000 Series NX-OS SAN Switching Configuration Guide, Release 7.x
Configuring Fabric Configuration Servers
Downloads: This chapterpdf (PDF - 1.28MB) The complete bookPDF (PDF - 5.95MB) | The complete bookePub (ePub - 1.77MB) | Feedback

Configuring Fabric Configuration Servers

Configuring Fabric Configuration Servers

This chapter contains the following sections:

Configuring Fabric Configuration Servers

Information About FCS

The Fabric Configuration Server (FCS) provides discovery of topology attributes and maintains a repository of configuration information of fabric elements. A management application is usually connected to the FCS on the switch through an N port. The FCS views the entire fabric based on the following objects:

  • Interconnect element (IE) object—Each switch in the fabric corresponds to an IE object. One or more IE objects form a fabric.
  • Port object—Each physical port in an IE corresponds to a port object. This includes the switch ports (xE and F ports) and their attached N ports.
  • Platform object—A set of nodes may be defined as a platform object to make it a single manageable entity. These nodes are end-devices (host systems, storage subsystems) attached to the fabric. Platform objects reside at the edge switches of the fabric.

Each object has its own set of attributes and values. A null value may also be defined for some attributes.

In the Cisco Nexus device environment, a fabric may consist of multiple VSANs. One instance of the FCS is present per VSAN.

FCS supports the discovery of virtual devices. The fcs virtual-device-add command, entered in FCS configuration submode, allows you to discover virtual devices in a particular VSAN or in all VSANs.

If you have attached a management application to a switch, all the frames directed towards the FCS in the switch are part of the port VSAN in the switch port (F port). Your view of the management application is limited only to this VSAN. However, information about other VSANs that this switch is part of can be obtained either through the SNMP or CLI.

In the following figure, Management Application 1 (M1) is connected through an F port with port VSAN ID 1, and Management Application 2 (M2) is connected through an F port with port VSAN ID 2. M1 can query the FCS information of switches S1 and S3, and M2 can query switches S3 and S4. Switch S2 information is not known to both of them. FCS operations can be done only on those switches that are visible in the VSAN. M2 can send FCS requests only for VSAN 2 even though S3 is also a part of VSAN 1.

Figure 1. FCSs in a VSAN Environment

FCS Characteristics

FCSs have the following characteristics:

  • Support network management including the following:
    • N port management application can query and obtain information about fabric elements.
    • SNMP manager can use the FCS management information base (MIB) to start discovery and obtain information about the fabric topology.
  • Support TE ports in addition to the standard F and E ports.
  • Can maintain a group of nodes with a logical name and management address when a platform registers with it. FCSs maintain a backup of all registrations in secondary storage and update it with every change. When a restart or switchover happens, FCSs retrieve the secondary storage information and rebuild its database.
  • SNMP manager can query FCSs for all IEs, ports, and platforms in the fabric.

FCS Name Specification

You can specify if the unique name verification is for the entire fabric (globally) or only for locally (default) registered platforms.


Note


Set this command globally only if every switch in the fabric belong to the Cisco MDS 9000 Family or Cisco Nexus devices.


To enable global checking of the platform name, perform this task:

To register platform attributes, perform this task:

Procedure
     Command or ActionPurpose
    Step 1switch# configure terminal  

    Enters global configuration mode.

     
    Step 2 switch(config)# fcs plat-check-global vsan vsan-id
     

    Enables global checking of the platform name.

     
    Step 3 switch(config)# no fcs plat-check-global vsan vsan-id
     

    Disables (default) global checking of the platform name.

     

    Displaying FCS Information

    You can use the show fcs commands to display the status of the WWN configuration.

    The following example shows how to display the FCS local database:

    switch# show fcs database
    

    The following example shows how to display a list of all interconnect elements for VSAN 1:

    switch# show fcs ie vsan 1
    

    The following example shows how to display information for a specific platform:

    switch# show fcs platform name SamplePlatform vsan 1
    

    The following example shows how to display port information for a specific pWWN:

    switch# show fcs port pwwn 20:51:00:05:30:00:16:de vsan 24
    

    Default FCS Settings

    The following table lists the default FCS settings.

    Table 1  Default FCS Settings

    Parameters

    Default

    Global checking of the platform name

    Disabled

    Platform node type

    Unknown