Cisco Nexus 1010 Command Reference, Release 4.2(1)SP1(3)
I Commands
Downloads: This chapterpdf (PDF - 127.0KB) The complete bookPDF (PDF - 5.19MB) | Feedback

I Commands

Table Of Contents

I Commands

import

install nexus1010

interface mgmt

interface VsbEthernet

ip address


I Commands


This chapter describes the Cisco Nexus 1010 commands that begin with the letter I.

import

To import a previously saved backup copy of a virtual service blade (VSB) from remote storage to the Cisco Nexus 1010, use the import command.

import [primary | secondary] filename

Syntax Description

primary

(Optional) The Cisco Nexus 1010 that was assigned the primary role.

secondary

(Optional) The Cisco Nexus 1010 that was assigned the secondary role.

filename

Import file name.


Defaults

None

Command Modes

Virtual service blade configuration (config-vsb-config)

Supported User Roles

network-admin

Command History

Release
Modification

4.2(1)SP1(3)

This command was introduced.


Usage Guidelines

If importing to a redundant pair of Cisco Nexus 1010s, you must specify whether importing to the primary or secondary.

You have verified that the bootflash: export-import directory is empty. If files are present in this directory, you must delete them before importing a VSB configuration file.

Before importing, you have copied the exported image file from remote storage into the Cisco Nexus 1010 export-import folder in the bootflash: repository.

Examples

This example shows how to import the image file Vdisk1.img.tar.00 to the primary VSB vsm-1 and power off the VSB:

n1010# config t
n1010(config) virtual-service-blade vsm-1
n1010-1(config-vsb-config)# import primary Vdisk1.img.tar.00
Note: import started..
Note: please be patient..
Note: Import cli returns check VSB status for completion
n1010-1(config-vsb-config)#

Related Commands

Command
Description

show network

Displays information about the network.

show virtual-service-blade

Displays information about virtual services.

show virtual-service-blade-
type summary

Displays a summary of all virtual service configurations by type, such as Virtual Supervisor Module (VSM) or Network Analysis and Monitoring (NAM).

export

Exports a VSB configuration file from the Cisco Nexus 1010.


install nexus1010

To install management software for the Cisco Nexus 1010, use the install nexus1010 command.

install nexus1010 {bootflash: path}

Syntax Description

bootflash:

Specifies a path from the bootflash directory.

path

Full path to the image file (.iso)


Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin

Command History

Release
Modification

4.0(4)SP1(1)

This command was introduced.


Usage Guidelines

You can view the available installation image files by using the dir command. For example:

n1010# dir bootflash:
n
      77824     Mar 27 06:02:44 2010  accounting.log
      16384     Mar 26 22:31:33 2010  lost+found/
       5023     Jan 18 00:23:37 2009  mts.log
   48346519     Jan 15 21:33:25 2001  nexus-1010-mzg.4.0.4.SP1.0.171.bin
       4096     Jan 15 21:27:11 2001  repository/

Usage for bootflash://
  308473856 bytes used
 3682906112 bytes free
 3991379968 bytes total
n1010# cd repository
n1010# dir

      77824     Jan 24 05:02:49 2001  accounting.log
        370     Jan 24 05:03:02 2001  cppa_mgr.log
      16384     Jan 15 21:33:09 2001  lost+found/
    1331914     Jan 15 21:33:21 2001  nexus-1010.4.0.4.SP1.0.197.iso
   20971008     Jan 15 21:33:22 2001  nexus-1010-4.0.4.SP1.0.171.iso


Usage for bootflash://
  308473856 bytes used
 3682906112 bytes free
 3991379968 bytes total
Nexus1010#

Examples

This example shows how to install management software for the Cisco Nexus 1010:

n1010# install nexus1010 bootflash:repository/nexus-1010.4.0.4.SP1.0.197.iso
cppa_mgr debug: Using URI: bootflash:/repository/nexus-1010.4.0.4.SP1.0.197.iso
Installing bootflash:/repository/nexus-1010.4.0.4.SP1.0.197.iso
.................................................................................
Installation complete.
Save configuration and restart for changes to take effect

n1010# 
#

Related Commands

Command
Description

dir

Displays the contents of a directory or file.

copy running-config startup-config

Copies the running configuration to the startup configuration.



interface mgmt

To configure the management interface and enter interface configuration mode, use the interface management command.

interface mgmt0

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Global configuration (config)
Interface configuration (config-if)

Supported User Roles

network-admin

Command History

Release
Modification

4.0(4)SP1(1)

This command was introduced.


Usage Guidelines

Use the interface mgmt0 command to configure the management interface and to enter the interface configuration mode.

Examples

This example shows how to enter the interface configuration mode to configure the management interface:

n1010(config)# interface mgmt0
n1010(config-if)#

Related Commands

Command
Description

show interface brief

Displays a short version of the interface configuration.

interface loopback

Create and configures a loopback interface.


interface VsbEthernet

To configure the virtual service blade (VSB) Ethernet interface and enter interface configuration mode, use the interface VsbEthernet command.

interface VsbEthernet name

Syntax Description

name

Name of virtual service blade interfaceVsbEthernet [slot-id | vb-id | intf-id].


Defaults

None

Command Modes

Global configuration (config)

Supported User Roles

network-admin

Command History

Release
Modification

4.2(1)SP1(3)

This command was introduced.


Usage Guidelines

Examples

This example shows how how to enter the interface configuration mode on VsbEthernet 1/1/2:

n1010# config t
n1010(config)# interface vsbEthernet 1/1/2
n1010(config-if)#

Related Commands

Command
Description

show interface brief

Displays a short version of the interface configuration.

show interface ethernet

Displays information about the Ethernet interface.

show interface mgmt0

Displays information about the traffic on the management interface.

show interface vethernet

Displays information about the traffic on the specified virtual Ethernet interface.


ip address

To create an IP route, use the ip address command. To remove an IP address, use the no form of this command.

ip address {address mask | prefix} {next-hop | next-hop-prefix | interface-type interface-number} [tag tag-value | preference]

no ip address {address mask | prefix} {next-hop | next-hop-prefix | interface-type interface-number} [secondary | tag tag-value | preference]

Syntax Description

address

IP address, in format A.B.C.D.

mask

IP network mask, in format A.B.C.D.

prefix

IP prefix and network mask length, in format A.B.C.D/LEN.

next-hop

IP next-hop address, in format A.B.C.D.

next-hop-prefix

IP next-hop prefix in format A.B.C.D./LEN.

interface-type

Interface type.

interface-number

Interface or subinterface number.

secondary

(Optional) Configures additional IP addresses on the interface.

tag

(Optional) Specifies a supply tag.

tag-value

Supply tag value. The range of valid values is from 0 to 4294967295. The default is 0.

preference

(Optional) Route preference.


Defaults

None

Command Modes

Global configuration (config)

Supported User Roles

network-admin

Command History

Release
Modification

4.0(4)SP1(1)

This command was introduced.


Examples

This example shows how to create an IP address:

n1010(config)# configure terminal
n1010(config)# ip address 209.165.200.225 255.255.255.224 x
n1010(config)# 

Related Commands

Command
Description

show ip interface A.B.C.D.

Displays interfaces for local IP addresses.