Cisco 7600 Series Ethernet Services 40G Line Card Hardware Installation Guide
Cisco 7600 Series Ethernet Services 40G Line Card Product Overview
Downloads: This chapterpdf (PDF - 163.0KB) The complete bookPDF (PDF - 3.08MB) | Feedback

Table of Contents

Cisco 7600 Ethernet Services Plus Line Card Product Overview

Introduction to the Cisco 7600 ES+ and ES+ Combo Low Queue Line Cards

Product Overview

Cisco 7600 Series Ethernet Services Plus Line Card Product Numbers

Supported Platforms

Cisco IOS Software Release and Hardware Revision Requirements

Modular Optics Compatibility

Power Management

Cisco 7600 Ethernet Services Plus Line Card Product Overview

This chapter provides an introduction to the Cisco 7600 Series Ethernet Services Plus (ES+) line cards and ES+ combo low queue line cards. It includes the following sections:

Introduction to the Cisco 7600 ES+ and ES+ Combo Low Queue Line Cards

The Cisco 7600 Series ES+ line cards are a multiple-fabric, fixed-port Ethernet line card for the Cisco 7600 series routers that are capable of 40 gbps full-duplex traffic forwarding using a fixed port interface design. The Cisco 7600 Series ES+ line card versions are:

  • 40-port version: 7600-ES+40G3C
  • 40-port version: 7600-ES+40G3CXL
  • 20-port version: 7600-ES+20G3C
  • 20-port version: 7600-ES+20G3CXL
  • 4-port version: 7600-ES+4TG3C
  • 4-port version: 7600-ES+4TGCXL
  • 2-port version: 7600-ES+2TG3C
  • 2-port version: 7600-ES+2TGCXL
  • 2-port version: 76-ES+XT-2TG3C
  • 2-port version: 76-ES+XT-2TG3CXL
  • 4-port version: 76-ES+XT-4TG3C
  • 4-port version: 76-ES+XT-4TG3CXL
  • 20-port version: 76-ES+T-20G
  • 2-port version: 76-ES+T-2TG
  • 40-port version: 76-ES+T-40G
  • 4-port version: 76-ES+T-4TG
  • 11-port version: 76-ES+XC-20G3C
  • 11-port version: 76-ES+XC-20G3CXL
  • 22-port version: 76-ES+XC-40G3C
  • 22-port version: 76-ES+XC-40G3CXL
  • 11-port version: 76-ES+T+XC-20G
  • 22-port version: 76-ES+T+XC-40G
  • 8-port version: 76-ES+T-8TG
  • 8-port version: 76-ES+XT-8TG

The difference between the versions are the link interface daughter cards that accept small form-factor pluggable (SFP, SFP+, or XFP1) optical transceivers. Additionally, each of the versions has a common baseboard card and a control processor daughter card, except for the 8 port version (76-ES+T-8TG) which has a different baseboard.

The SFP, SFP+, and XFP modules allow the line cards to be configured for different media types (copper or fiber) and different optical requirements (single mode fiber or multimode fiber) as available.

See Table 1-4 for information about which SFPs, SFP+, or XFPs are accepted on the different Cisco 7600 Series ES+ line cards.

Product Overview

The Cisco 7600 Series ES+ line cards have the following features:

The system features listed here specify some of the key performance metrics and capabilities of the line cards. The information below applies to all four line cards unless stated otherwise.

  • Line rate feature processing performance with 64 byte packets for four ports of 10 GE or forty ports of GE (59.52Mpps). Note that the line card throughput is limited by the system switch fabric. The packet processor and internal sections of the line card are full line rate throughput capable for 40GbE.
  • Large output buffers provide up to 200 mS of round-trip-time buffer (100 mS in each direction) per 10GE port or 10xGE ports to prevent transient output overloads from causing spurious packet loss.
  • Up to 32K queues (per 10GE port or 10xGE ports) per direction for input or output queuing and scheduling.
  • Programmable ingress and egress feature processing capability through the Trident.
  • 40+ Mpps Layer 3 or Layer 4 forwarding, 125Mpps Layer 2 forwarding.
  • Dual fabric attachment providing an aggregate bandwidth of 40Gb/s, full duplex (each fabric channel provides 20Gb/s, full duplex).
  • 512-MB boot disk

Cisco 7600 Series Ethernet Services Plus Line Card Product Numbers

Table 1-1 lists the Cisco product numbers for the line cards.

Table 1-1 Cisco 7600 Ethernet Services Plus Line Card Product Numbers

Description
Cisco Product Number
Field-Replaceable Unit (FRU) Product ID

20xGE SFP with DFC 3C

7600-ES+20G3C

7600-ES+20G3C=

20xGE SFP with DFC 3CXL

7600-ES+20G3CXL

7600-ES+20G3CXL=

2x10GE XFP with DFC 3C

7600-ES+2TG3C

7600-ES+2TG3C=

2x10GE XFP with DFC 3CXL

7600-ES+2TG3CXL

7600-ES+2TG3CXL=

40xGE SFP with DFC 3C

7600-ES+40G3C

7600-ES+40G3C=

40xGE SFP with DFC 3CXL

7600-ES+40G3CXL

7600-ES+40G3CXL=

4x10GE XFP with DFC 3C

7600-ES+4TG3C

7600-ES+4TG3C=

4x10GE XFP with DFC 3CXL

7600-ES+4TG3CXL

7600-ES+4TG3CXL=

7600 ES+XT, LAN/WAN PHY, OTN/G.709, 2x10GE, XFP, DFC3C

76-ES+XT-2TG3C

76-ES+XT-2TG3C=

7600 ES+XT, LAN/WAN PHY, OTN/G.709, 2x10GE, XFP, DFC3CXL

76-ES+XT-2TG3CXL

76-ES+XT-2TG3CXL=

7600 ES+XT, LAN/WAN PHY, OTN/G.709, 4x10GE, XFP, DFC3C

76-ES+XT-4TG3C

76-ES+XT-4TG3C=

7600 ES+XT, LAN/WAN PHY, OTN/G.709, 4x10GE, XFP, DFC3CXL

76-ES+XT-4TG3CXL

76-ES+XT-4TG3CXL=

20xGE with DFC 3CXL

76-ES+T-20G

76-ES+T-20G=

2x10GE with DFC 3CXL

76-ES+T-2TG

76-ES+T-2TG=

40xGE with DFC 3CXL

76-ES+T-40G

76-ES+T-40G=

4x10GE with DFC 3CXL

76-ES+T-4TG

76-ES+T-4TG=

7600 ES+XC, LAN/WAN PHY, OTN/G.709, Combo 10x1GE/ 1x10GE, DFC3C

76-ES+XC-20G3C

76-ES+XC-20G3C=

7600 ES+XC, LAN/WAN PHY, OTN/G.709, Combo 10x1GE/ 1x10GE, DFC3CXL

76-ES+XC-20G3CXL

76-ES+XC-20G3CXL=

7600 ES+XC, LAN/WAN PHY, OTN/G.709, Combo 20x1GE/ 2x10GE, DFC3C

76-ES+XC-40G3C

76-ES+XC-40G3C=

7600 ES+XC, LAN/WAN PHY, OTN/G.709, Combo 20x1GE/ 2x10GE, DFC3CXL

76-ES+XC-40G3CXL

76-ES+XC-40G3CXL=

7600 ES+XC, LAN/WAN PHY, OTN/G.709, Combo 10x1GE/ 1x10GE, DFC3CXL

76-ES+T+XC-20G

76-ES+T+XC-20G=

7600 ES+XC, LAN/WAN PHY, OTN/G.709, Combo 20x1GE/ 2x10GE, DFC3CXL

76-ES+T+XC-40G

76-ES+T+XC-40G=

8x10GE with DFC 3CXL

76-ES+T-8TG

76-ES+T-8TG=

8x10GE with DFC 3CXL

76-ES+XT-8TG3CXL

76-ES+XT-8TG3CXL=


NoteThe Distributed Forwarding Card (DFC) on a 7600 ES+ line card functions at the level of the lowest common denominator DFC in the system. If the only DFC in a system is a DFC 3CXL, then the system would operate at the 3CXL level. If a DFC 3CXL is configured in a system with a DFC3BXL present, then the system will function at the DFC 3BXL level. Additionally, a DFC 3CXL provides for more TCAM entries than does a DFC 3C. The Distributed Forwarding Card (DFC) on a 7600 ES+ line card functions at the level of the lowest common denominator DFC in the system. If the only DFC in a system is a DFC 3CXL, then the system would operate at the 3CXL level. If a DFC 3CXL is configured in a system with a DFC3BXL present, then the system will function at the DFC 3BXL level. Additionally, a DFC 3CXL provides for more TCAM entries than does a DFC 3C.


Supported Platforms

Table 1-2 lists the supported router platforms for Cisco 7600 ES+ line cards:

Table 1-2 Cisco 7600 ES+ Line Card Supported Router Platforms

Cisco 7600 ES+ Line Card
Supported Platform

7600-ES+20G3C

All Cisco 7600 series routers except for the Cisco 7603 router

7600-ES+20G3CXL

All Cisco 7600 series routers except for the Cisco 7603 router

7600-ES+2TG3C

All Cisco 7600 series routers except for the Cisco 7603 router

7600-ES+2TG3CXL

All Cisco 7600 series routers except for the Cisco 7603 router

7600-ES+40G3C

All Cisco 7600 series routers except for the Cisco 7603 router

7600-ES+40G3CXL

Except for the Cisco 7603 router, all Cisco 7600 series routers including 7603-S.

7600-ES+4TG3C

All Cisco 7600 series routers except for the Cisco 7603 router

7600-ES+4TG3CXL

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+XT-2TG3C

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+XT-2TG3CXL

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+XT-4TG3C

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+XT-4TG3CXL

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+T-20G

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+T-2TG

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+T-40G

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+T-4TG

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+XC-20G3C

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+XC-20G3CXL

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+XC-40G3C

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+XC-40G3CXL

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+T+XC-20G

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+T+XC-40G

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+T-8TG

All Cisco 7600 series routers except for the Cisco 7603 router

76-ES+XT-8TG3CXL

All Cisco 7600 series routers except for the Cisco 7603 router

Cisco IOS Software Release and Hardware Revision Requirements

The Cisco 7600 ES+ line cards have certain Cisco IOS software requirements. Also, to ensure compatibility with the software, your Cisco 7600 ES+ line card should have a specific hardware revision number. The number is printed on a label affixed to the component side of the card and is displayed by the show diag command.

Table 1-3 lists the hardware and software requirements for Cisco 7600 ES+ line cards.

Table 1-3 Cisco 7600 ES+ Line Card and Cisco IOS Release and Hardware Version Compatibility

Cisco 7600 ES+ Line Card
Cisco Product Number
Required
Hardware Version
Minimum Cisco IOS Software Release

7600 ES+ Line Card, 20xGE SFP with DFC 3C

7600-ES+20G3C

68-2868-05

Cisco IOS Release 12.2(33)SRD

7600 ES+ Line Card, 20xGE SFP with DFC 3CXL

7600-ES+20G3CXL

68-3030-05

Cisco IOS Release 12.2(33)SRD

7600 ES+ Line Card, 2x10GE XFP with DFC 3C

7600-ES+2TG3C

68-2867-04

Cisco IOS Release 12.2(33)SRD

7600 ES+ Line Card, 2x10GE XFP with DFC 3CXL

7600-ES+2TG3CXL

68-3029-04

Cisco IOS Release 12.2(33)SRD

7600 ES+ Line Card, 40xGE SFP with DFC 3C

7600-ES+40G3C

68-2869-05

Cisco IOS Release 12.2(33)SRD

7600 ES+ Line Card, 40xGE SFP with DFC 3CXL

7600-ES+40G3CXL

68-3032-05

Cisco IOS Release 12.2(33)SRD

7600 ES+ Line Card, 4x10GE XFP with DFC 3C

7600-ES+4TG3C

68-2866-06

Cisco IOS Release 12.2(33)SRD

7600 ES+ Line Card, 4x10GE XFP with DFC 3CXL

7600-ES+4TG3CXL

68-3031-06

Cisco IOS Release 12.2(33)SRD

7600 ES+XT, LAN/WAN PHY, OTN/G.709, 2x10GE, XFP, DFC3C

76-ES+XT-2TG3C

68-3558-01

Cisco IOS Release 12.2(33)SRD1

7600 ES+XT, LAN/WAN PHY, OTN/G.709, 2x10GE, XFP, DFC3CXL

76-ES+XT-2TG3CXL

68-3335-03

Cisco IOS Release 12.2(33)SRD1

7600 ES+XT, LAN/WAN PHY, OTN/G.709, 4x10GE, XFP, DFC3C

76-ES+XT-4TG3C

68-3557-01

Cisco IOS Release 12.2(33)SRD1

7600 ES+XT, LAN/WAN PHY, OTN/G.709, 4x10GE, XFP, DFC3CXL

76-ES+XT-4TG3CXL

68-3336-03

Cisco IOS Release 12.2(33)SRD1

7600 ES+T Line Card, 20xGE SFP with DFC 3CXL

76-ES+T-20G

68-3030-06

Cisco IOS Release 12.2(33)SRD4

7600 ES+XT, LAN/WAN PHY, OTN/G.709, Low Queue, 2x10GE, XFP, DFC3CXL

76-ES+T-2TG

68-3029-05

Cisco IOS Release 12.2(33)SRD4

7600 ES+T Line Card, 40xGE SFP with DFC 3CXL

76-ES+T-40G

68-3032-06

Cisco IOS Release 12.2(33)SRD4

7600 ES+XT, LAN/WAN PHY, OTN/G.709, Low Queue, 4x10GE, XFP, DFC3CXL

76-ES+T-4TG

68-3031-05

Cisco IOS Release 12.2(33)SRD4

7600 ES+XC Combo 10x1GE/ 1x10GE, DFC3C

76-ES+XC-20G3C

68-3168-06

Cisco IOS Release 12.2(33)SRE

7600 ES+XC Combo 10x1GE/ 1x10GE, DFC3CXL

76-ES+XC-20G3CXL

68-3169-06

Cisco IOS Release 12.2(33)SRE

7600 ES+XC Combo 20x1GE/ 2x10GE, DFC3C

76-ES+XC-40G3C

68-3166-06

Cisco IOS Release 12.2(33)SRE

7600 ES+XC Combo 20x1GE/ 2x10GE, DFC3CXL

76-ES+XC-40G3CXL

68-3167-06

Cisco IOS Release 12.2(33)SRE

7600 ES+XC Combo low queue 10x1GE/ 1x10GE, DFC3CXL

76-ES+T+XC-20G

68-4492-2

Cisco IOS 15.2(2)S

7600 ES+XC Combo low queue 20x1GE/ 2x10GE, DFC3CXL

76-ES+T+XC-40G

68-4492-1

Cisco IOS 15.2(2)S

7600 ES+T Low queue 8x 10GE, DFC3CXL

76-ES+T-8TG

 

Cisco IOS 15.2(4)S

7600 ES+T High queue 8x 10GE, DFC3CXL

76-ES+XT-8TG3CXL

68-4765-01

Cisco IOS 15.3(1)S

The show diag slot_number , show version , and show hardware commands display the current hardware configuration of the router, including the system software version that is currently loaded and running, and the hardware revision number. For complete descriptions of show commands, refer to the Cisco IOS Configuration Fundamentals Configuration Guide and the Cisco IOS Configuration Fundamentals Command Reference for the installed Cisco IOS release.

If the command displays indicate that the Cisco IOS software is a version earlier than you need, check the contents of flash memory to determine if the required images are available on your system. The dir devicename command displays a list of all files stored in flash memory. If you do not have the correct software version, contact Cisco customer service.

For software configuration information, refer to the Cisco IOS software configuration and command reference publications for the installed Cisco IOS release. Also refer to the Cisco IOS software release notes for additional information.

Modular Optics Compatibility

The Cisco 7600 Series ES+ line cards use small form-factor pluggable (SFP, SFP+, or XFP) optical transceivers to provide network connectivity. Table 1-4 provides links to tables showing the supported modules for the different Cisco 7600 Series ES+ line cards.

Table 1-4 Supported Optical Transceiver Modules

Line Cards
Supported Modules

7600-ES+20G3C

Cisco 7600 ES+ 20G3C, -20G3CXL Supported SFP Modules; see Table 2-16.

7600-ES+20G3CXL

7600-ES+2TG3C

Cisco 7600 ES+ 2TG3C, -3CXL Supported XFP Modules; see .

7600-ES+2TG3CXL

7600-ES+40G3C

Cisco 7600 ES+ 40G3C, -40G3CXL Supported SFP Modules; see Table 2-21.

7600-ES+40G3CXL

7600-ES+4TG3C

Cisco 7600 ES+ 4TG3C, -4TG3CXL Supported XFP Modules; see .

7600-ES+4TG3CXL

76-ES+XT-2TG3C

Cisco 76-ES+XT-2TG3C, -2TG3CXL Supported XFP Modules; see Table 2-26.

76-ES+XT-2TG3CXL

76-ES+XT-4TG3C

Cisco 76-ES+XT-2TG3C, -2TG3CXL Supported XFP Modules; see Table 2-31.

76-ES+XT-4TG3CXL

76-ES+T-20G

Supported SFP Modules; see Table 2-16

76-ES+T-2TG

Supported XFP Modules; see Table 2-26

76-ES+T-40G

Supported SFP Modules; see Table 2-21

76-ES+T-4TG

Supported XFP Modules; see Table 2-31

76-ES+XC-20G3C

Supported SFP Modules; see TBD; Supported XFP Modules; see TBD

76-ES+XC-20G3CXL

Supported SFP Modules; see TBD; Supported XFP Modules; see TBD

76-ES+XC-40G3C

Supported SFP Modules; see TBD; Supported XFP Modules; see TBD

76-ES+XC-40G3CXL

Supported SFP Modules; see TBD; Supported XFP Modules; see TBD

76-ES+T-8TG

Supported SFP+ Modules; see Table 2-78 .

76-ES+XT-8TG

Supported SFP+ Modules; see Table 2-83

Power Management

The Cisco ES+ line cards consume chassis power; you must make sure the chassis is within the power budget on Cisco 7600 series routers. See Table 1-5 .

Table 1-5 Cisco 7600 ES+ Line Card Power Consumption

Cisco 7600 Series ES+ line cards
Power Consumption (Maximum in Watts)

7600-ES+20G3C

277

7600-ES+20G3CXL

305

7600-ES+2TG3C

269

7600-ES+2TG3CXL

297

7600-ES+40G3C

391

7600-ES+40G3CXL

419

7600-ES+4TG3C

371

7600-ES+4TG3CXL

399

76-ES+XT-2TG3C

273

76-ES+XT-2TG3CXL

301

76-ES+XT-4TG3C

378

76-ES+XT-4TG3CXL

406

76-ES+T-20G

305

76-ES+T-2TG

301

76-ES+T-40G

419

76-ES+T-4TG

406

7600-ES+XC-20G3C

309

7600-ES+XC-20G3CXL

337

7600-ES+XC-40G3C

399

7600-ES+XC-40G3CXL

427

76-ES+T+XC-20G

337

76-ES+T+XC-40G

427

76-ES+T-8TG

433

76-ES+XT-8TG

433

If the power limit is exceeded, the Cisco ES+ line card is not powered up and an error message is displayed.

Router#%C7KPWR-SP-4-POWERDENIED:insufficient power, module in slot 3 power denied.
 

On a Cisco 7600 series router, use the show power command on the Route Processor to determine how much power you have available in the chassis and how much is being used or reserved by line cards, supervisor engines, and fan trays.


NoteThe The show power command displays only the values programmed in the IDPROM and the IDPROM is not dynamically updated for different power values.


This is sample output for the show power command on a Cisco 7600 series router:

Router# show power
 
system power redundancy mode = redundant
system power redundancy operationally = non-redundant
system power total = 3795.12 Watts (90.36 Amps @ 42V)
system power used = 3320.94 Watts (79.07 Amps @ 42V)
system power available = 474.18 Watts (11.29 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-4000W-INT 3795.12 90.36 OK OK on
2 none
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 WS-C6K-13SLT-FAN2 298.20 7.10 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
2 7600-SIP-200 240.24 5.72 240.24 5.72 on on
3 WS-X6724-SFP 125.16 2.98 125.16 2.98 on on
4 7600-SIP-400 265.02 6.31 265.02 6.31 on on
7 RSP720-3CXL-GE 354.06 8.43 354.06 8.43 on on
8 RSP720-3C-GE 354.06 8.43 354.06 8.43 on on
9 7600-ESM-BASE 304.92 7.26 304.92 7.26 on on
10 7600-ES+20G3CXL 297.36 7.08 297.36 7.08 on on
11 7600-SIP-600 341.88 8.14 341.88 8.14 on on
12 7600-SIP-600 341.88 8.14 341.88 8.14 on on
13 WS-X6704-10GE 398.16 9.48 398.16 9.48 on on
Router#
 

This is sample output for the show power command on a Cisco 7600 series router for a 76-ES+T+XC-40G low queue combo card:

A3-2#show power
system power redundancy mode = redundant
system power redundancy operationally = non-redundant
system power total = 2671.20 Watts (63.60 Amps @ 42V)
system power used = 1477.14 Watts (35.17 Amps @ 42V)
system power available = 1194.06 Watts (28.43 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-6000W 2671.20 63.60 OK OK on
2 none
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
1 7600-SIP-600 341.88 8.14 341.88 8.14 on on
4 7600-ES20-GE3C 340.20 8.10 - - off off (admin request)
5 (Redundant Sup) - - 354.06 8.43 - -
6 RSP720-3CXL-GE 354.06 8.43 354.06 8.43 on on
7 7600-ES+20G3C 276.36 6.58 - - off off (admin request)
8 7600-ES20-GE3C 340.20 8.10 - - off off (admin request)
9 '76-ES+T+XC-40G' 427.14 10.17 427.14 10.17 on on
 
This is sample output for the show power command on a Cisco 7600 series router for a 76-ES+T+XC-20G low queue combo card:
A1-2#show power
system power redundancy mode = redundant
system power redundancy operationally = non-redundant
system power total = 2669.10 Watts (63.55 Amps @ 42V)
system power used = 2181.90 Watts (51.95 Amps @ 42V)
system power available = 487.20 Watts (11.60 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 PWR-2700-AC 2669.10 63.55 OK OK on
2 none
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 FAN-MOD-6HS 180.18 4.29 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
1 76-ES+T+XC-20G 337.26 8.03 337.26 8.03 on on
2 WS-X6748-GE-TX 325.50 7.75 325.50 7.75 on on
3 7600-ES20-10G3CXL 340.20 8.10 340.20 8.10 on on
4 7600-SIP-600 341.88 8.14 341.88 8.14 on on
5 (Redundant Sup) - - 328.44 7.82 - -
6 WS-SUP720-3BXL 328.44 7.82 328.44 7.82 on on

This is sample output for the show power command on a Cisco 7600 series router for a 76-ES+T-8TG low queue card:

Router#show power
system power redundancy mode = redundant
system power redundancy operationally = non-redundant
system power total = 2671.20 Watts (63.60 Amps @ 42V)
system power used = 1536.36 Watts (36.58 Amps @ 42V)
system power available = 1134.84 Watts (27.02 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-6000W 2671.20 63.60 OK OK on
2 none
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 FAN-MOD-9SHS 241.50 5.75 OK
2 FAN-MOD-9SHS 241.50 5.75 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
2 76-ES+T-8TG 432.60 10.30 432.60 10.30 on on
5 (Redundant Sup) - - 310.38 7.39 - -
6 RSP720-3C-GE 310.38 7.39 310.38 7.39 on on