Guest

Cisco 12000 Series Routers

Cisco 12016, Cisco 12416, and Cisco 12816 Scissor-Jack Instructions

  • Viewing Options

  • PDF (1.0 MB)
  • Feedback
Cisco 12016, Cisco 12416, and Cisco 12816 Router Scissor-Jack Instructions

Table Of Contents

Cisco 12016, Cisco 12416, and Cisco 12816 Router
Scissor-Jack Instructions

Introduction

Contents

Scissor-Jack Overview

Preparing for Installation

Safety Guidelines

Safety with Equipment

Safety with Electricity

Preventing Electrostatic Discharge Damage

Required Tools and Equipment

Related Documentation

Using the Scissor-Jack Platform

Moving a Router onto the Scissor-Jack

Moving a Router onto a Pallet

Regulatory, Compliance, and Safety Information

Translated Safety Warnings and Agency Approvals

Electromagnetic Compatibility Regulatory Statements

FCC Class A Compliance

CISPR 22

Canada

Europe (EU)

VCCI Class A Notice for Japan

Class A Notice for Hungary

Class A Notice for Taiwan and Other Traditional Chinese Markets

Class A Notice for Korea

Obtaining Documentation

Cisco.com

Documentation CD-ROM

Ordering Documentation

Documentation Feedback

Obtaining Technical Assistance

Cisco TAC Website

Opening a TAC Case

TAC Case Priority Definitions

Obtaining Additional Publications and Information


Cisco 12016, Cisco 12416, and Cisco 12816 Router
Scissor-Jack Instructions


Cisco Product Number: GSR16-SCR-TABLE=
Document Order Number: DOC-7815717=

Introduction

This publication contains instructions for using the scissor-jack platform with
Cisco 12016, Cisco 12416, and Cisco 12816 Routers.

Contents

The following sections are included in this publication:

Scissor-Jack Overview

Preparing for Installation

Using the Scissor-Jack Platform

Regulatory, Compliance, and Safety Information

Obtaining Documentation

Obtaining Technical Assistance

Obtaining Additional Publications and Information

Scissor-Jack Overview

The scissor-jack platform enables a team of two installers to easily move a fully loaded router. This publication describes how to move a router chassis from an equipment rack and onto the scissor-jack, and then describes how to move it from the scissor-jack and onto a shipping pallet.

Preparing for Installation

Installation preparation is presented in the following sections:

Safety Guidelines

Preventing Electrostatic Discharge Damage

Required Tools and Equipment

Related Documentation

Safety Guidelines

Before you perform any procedure in this publication, review the safety guidelines in this section to avoid injuring yourself or damaging the equipment. In addition, review the safety warnings listed in the Regulatory Compliance and Safety Information for the Cisco 12000 Series Internet Router publication that accompanied your router before installing, configuring, or maintaining the router.

The following guidelines are for your safety and to protect equipment. The guidelines do not include all hazards. Be alert.

Safety with Equipment

Always disconnect all power cords and interface cables before moving the system.

Never assume that power is disconnected from a circuit; always check.

Keep tools and assembly components away from walk areas.

Do not work alone if potentially hazardous conditions exist.

Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.

Carefully examine your work area for possible hazards such as moist floors, ungrounded power extension cables, and missing safety grounds.

Safety with Electricity

Before beginning any procedures requiring access to the interior of the router, locate the emergency power-off switch for the room in which you are working.

Disconnect all power and external cables before installing or removing a router.

Never assume that power has been disconnected from a circuit; always check.

Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.

Never install equipment that appears damaged.

Carefully examine your work area for possible hazards such as moist floors, ungrounded power extension cables, and missing safety grounds.

If an electrical accident does occur, proceed as follows:

Use caution; do not become a victim yourself. Disconnect power to the router.

If possible, send another person to get medical aid; otherwise, assess the condition of the victim and then call for help.

Determine if the person needs rescue breathing or external cardiac compressions; then take appropriate action.

In addition, observe the following guidelines when working with any equipment that is disconnected from a power source but still connected to telephone or network wiring:

Never install telephone wiring during a lightning storm.

Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

Use caution when installing or modifying telephone lines.

Preventing Electrostatic Discharge Damage

Many router components can be damaged by static electricity. Some components can be damaged by voltages as low as 30V, while static voltages as high as 35,000V can be generated just by handling plastic or foam packing material, or by sliding assemblies across plastic and carpets. Not exercising the proper electrostatic discharge (ESD) precautions can result in intermittent or complete component failures. To minimize the potential for ESD damage, observe the following guidelines:

Always use an ESD-preventive antistatic wrist strap or ankle strap and ensure that it makes good skin contact.


Caution You should periodically check the resistance value of the ESD-preventive strap. The measurement should be between 1 and 10 megohms.

When removing or installing a component, make sure the equipment end of your antistatic strap leash is connected to one of the ESD connection sockets on the front of the chassis or to a bare metal surface on the chassis. (See Figure 1.) Avoid contact between the component and your clothing. The ESD-preventive wrist strap only protects the component from ESD voltages on the body; ESD voltages on your clothing can still cause component damage.

Always place a card component-side-up on an antistatic surface, in an antistatic card rack, or in a static shielding bag. If you are returning the item to the factory, immediately place it in a static shielding bag.

When installing a line card or route processor (RP), use the ejector levers to seat the card connectors in the backplane, then tighten both captive screws on the faceplate of the card. These screws prevent accidental removal, provide proper grounding for the router, and help to ensure that the card connector is seated in the backplane.

When removing line cards, clock and scheduler cards, switch fabric cards, or an RP, use the ejector levers to unseat the card connector from the backplane. Pull the metal card carrier out slowly, placing one hand along the bottom of the carrier to guide it straight out of the slot.

Handle line cards, clock and scheduler cards, switch fabric cards, or an RP by the metal card carrier edges only; avoid touching the board or any connector pins.

Figure 1 Connecting an ESD-Preventive Wrist Strap to the Router

Required Tools and Equipment

You need the following tools and equipment to use the scissor-jack:

ESD-preventive wrist strap

Flat-blade and Phillips screwdrivers

3/4-in (19-mm) socket and ratchet wrench

Related Documentation

The following publications may be referenced for more information and procedures:

Cisco 12016, Cisco 12416, and Cisco 12816 Router Installation and Configuration Guide

Cisco 12016, Cisco 12416, and Cisco 12816 Router Unpacking Instructions

Regulatory Compliance and Safety Information for the Cisco 12000 Series Internet Router

Using the Scissor-Jack Platform

Procedures for using the scissor-jack platform to move a fully loaded chassis are described in the following sections:

Moving a Router onto the Scissor-Jack

Moving a Router onto a Pallet

Moving a Router onto the Scissor-Jack

To move a fully loaded router from an equipment rack and onto the scissor-jack platform, follow these steps:


Step 1 Working from the top of the chassis down, remove the screws that secure the chassis to the mounting flanges on the rack (five screws on each side of the chassis).

Step 2 Position the scissor-jack platform in front of the rack-mounting platform installed in the bottom of the rack, with the screw on the scissor-jack platform facing away from the front of the router and the back of the scissor-jack platform butted against the front of the rack-mounting platform.

Step 3 Use the 3/4-in (19-mm) socket and ratchet wrench to turn the scissor-jack screw counterclockwise and expand the scissor-jack platform so that the top of the platform is level with the top of the rack-mounting table under the chassis. (See Figure 2.)


Warning Do not attempt to lift the chassis with the handles on the back and sides of the chassis. These handles are not designed to support the weight of the chassis, and should be used only to steady and guide the chassis while it is being inserted into or removed from an equipment rack. To reduce the risk of damage to the chassis and serious bodily injury, do not use these handles to lift or support the chassis.


Figure 2 Preparing the Scissor-Jack Platform

Step 4 Position one person in front of the router to support and guide it while the second person slowly pushes the router to slide it off the rack-mounting table, out of the rack, and onto the scissor-jack platform. (See Figure 3.)

Figure 3 Transferring the Router to the Scissor-Jack Platform

Step 5 With one person positioned on the side of the router to prevent it from tipping, install the four chassis anchor clips through the slots in the bottom of the chassis, align the holes with the bolt holes in the platform, and insert and tighten the four bolts to prevent the chassis from shifting on the scissor-jack platform. (See Figure 4.)

Figure 4 Installing the Chassis Anchor Clips

Step 6 With one person positioned on the side of the router to prevent it from tipping, use the 3/4-inch (19-mm) socket and ratchet wrench to turn the scissor-jack screw clockwise slowly and close the scissor-jack platform to lower the chassis. (See Figure 5.)

Figure 5 Closing the Scissor-Jack Platform to Lower the Chassis

Step 7 Position the safety hand truck at one side of the router, slide the router and scissor-jack platform onto the safety hand truck, and secure the router to the hand truck with the locking safety strap.

Step 8 Tilt the safety hand truck onto its outrigger wheels to move the chassis to a level, open space with a solid floor, where the chassis can be repackaged for shipping.


Moving a Router onto a Pallet

To reinstall the router and scissor-jack platform onto the shipping pallet, use Figure 6 as a reference and follow these steps:


Step 1 Use the hand truck to move the chassis to a level, open space with a solid floor.

Step 2 Tilt the chassis upright so that it stands on the scissor-jack platform, then remove the hand truck.

Step 3 Use the bolts from the original shipping package to attach the eight hold-down brackets to the sides of the scissor-jack platform (two brackets on each side).


Note The hold-down brackets are not symmetrical: The bracket plate that fastens to the side of the scissor-jack platform is narrower than the bracket plate that fastens to the top of the pallet, and its bolt holes are smaller in diameter.


Step 4 Position the U-shaped pallet body behind the scissor-jack platform with the opening facing the back panel of the router.

Step 5 Use the 3/4-inch (19-mm) socket and ratchet wrench to turn the scissor-jack screw slowly counterclockwise to expand the scissor-jack platform and raise the top of the scissor-jack platform high enough for the hold-down brackets to clear the top of the pallet body.

Step 6 Slide the pallet body around the scissor-jack platform.

Step 7 Slide the pallet front bar into the opening on the pallet body and use the hinge locks to secure it as instructed in these steps:

a. Pivot the butterfly handle on the hinge lock up so that it is perpendicular to the body of the hinge lock.

b. Twist the butterfly handle counterclockwise to extend the hinge lock hook to its maximum reach.

c. Lower the hinge lock hook over the hinge lock catch on the pallet body.

d. Twist the butterfly handle clockwise to clamp the hinge lock hook on the hinge lock catch on the pallet body.

e. Pivot the butterfly lever down onto the hinge lock body so that it lies flat.

Step 8 Shift the pallet to ensure that it is positioned evenly all the way around the scissor-jack platform and that the bolt holes in the hold-down brackets on the sides of the scissor-jack platform are aligned with the holes in the top of the shipping pallet.

Step 9 Turn the scissor-jack screw slowly clockwise to close the scissor-jack platform and lower the top of the scissor-jack platform slowly until the hold-down brackets touch the top of the shipping pallet.

Step 10 Set a blocking plate into the hold-down bracket so that the blank side of the blocking plate is against the heads of the bolts in the side of the scissor-jack platform, and the open holes in the blocking plate align with the bolt holes in the top of the pallet.

Step 11 Insert bolts through each of the hold-down bracket holes and into the holes in the top of the shipping pallet, then use the 9/16-inch (14-mm) wrench to tighten the bolts.

Step 12 Turn the scissor-jack screw slowly clockwise to collapse the scissor-jack platform and raise the base of the scissor-jack platform until the weight of the router and scissor-jack platform is absorbed by the pallet. Continue turning the scissor-jack screw clockwise to close the scissor-jack platform and lift the base of the scissor-jack platform until the scissor-jack platform is completely closed (the screw can not be turned).


Figure 6 Installing the Router and Scissor-Jack Platform onto a Pallet

Regulatory, Compliance, and Safety Information

This section includes regulatory, compliance, and safety information in the following sections:

Translated Safety Warnings and Agency Approvals

Electromagnetic Compatibility Regulatory Statements

Translated Safety Warnings and Agency Approvals

The complete list of translated safety warnings and agency approvals is available in the Regulatory Compliance and Safety Information for Cisco 12000 Series Internet Routers publication.
(Document Number 78-4347-xx.)

Electromagnetic Compatibility Regulatory Statements

FCC Class A Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

Modifying the equipment without Cisco's authorization may result in the equipment no longer complying with FCC requirements for Class A digital devices. In that event, your right to use the equipment may be limited by FCC regulation and you may be required to correct any interference to radio or television communication at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

Turn the television or radio antenna until the interference stops.

Move the equipment to one side or the other of the television or radio.

Move the equipment farther away from the television or radio.

Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

CISPR 22

This apparatus complies with CISPR 22/EN55022 Class B radiated and conducted emissions requirements.

Canada

English Statement of Compliance

This class A digital apparatus complies with Canadian ICES-003.

French Statement of Compliance

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Europe (EU)

This apparatus complies with EN55022 Class B and EN55024 standards when used as ITE/TTE equipment, and EN300386 for Telecommunications Network Equipment (TNE) in both installation environments, telecommunication centers and other indoor locations.

VCCI Class A Notice for Japan

Warning


This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. Statement 191


Class A Notice for Hungary

Warning


This equipment is a class A product and should be used and installed properly according to the Hungarian EMC Class A requirements (MSZEN55022). Class A equipment is designed for typical commercial establishments for which special conditions of installation and protection distance are used. Statement 256


Class A Notice for Taiwan and Other Traditional Chinese Markets

Warning


This is a Class A Information Product, when used in residential environment, it may cause radio frequency interference, under such circumstances, the user may be requested to take appropriate countermeasures. Statement 257


Class A Notice for Korea

Warning


This is a Class A Device and is registered for EMC requirements for industrial use. The seller or buyer should be aware of this. If this type was sold or purchased by mistake, it should be replaced with a residential-use type. Statement 294


Obtaining Documentation

Cisco provides several ways to obtain documentation, technical assistance, and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation on the World Wide Web at this URL:

http://www.cisco.com/univercd/home/home.htm

You can access the Cisco website at this URL:

http://www.cisco.com

International Cisco websites can be accessed from this URL:

http://www.cisco.com/public/countries_languages.shtml

Documentation CD-ROM

Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which may have shipped with your product. The Documentation CD-ROM is updated regularly and may be more current than printed documentation. The CD-ROM package is available as a single unit or through an annual or quarterly subscription.

Registered Cisco.com users can order a single Documentation CD-ROM (product number DOC-CONDOCCD=) through the Cisco Ordering tool:

http://www.cisco.com/en/US/partner/ordering/ordering_place_order_ordering_tool_launch.html

All users can order annual or quarterly subscriptions through the online Subscription Store:

http://www.cisco.com/go/subscription

Click Subscriptions & Promotional Materials in the left navigation bar.

Ordering Documentation

You can find instructions for ordering documentation at this URL:

http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

You can order Cisco documentation in these ways:

Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Networking Products MarketPlace:

http://www.cisco.com/en/US/partner/ordering/index.shtml

Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).

Documentation Feedback

You can submit e-mail comments about technical documentation to bug-doc@cisco.com.

You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:

Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883

We appreciate your comments.

Obtaining Technical Assistance

For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, the Cisco Technical Assistance Center (TAC) provides 24-hour-a-day, award-winning technical support services, online and over the phone. Cisco.com features the Cisco TAC website as an online starting point for technical assistance. If you do not hold a valid Cisco service contract, please contact your reseller.

Cisco TAC Website

The Cisco TAC website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The Cisco TAC website is available 24 hours a day, 365 days a year. The Cisco TAC website is located at this URL:

http://www.cisco.com/tac

Accessing all the tools on the Cisco TAC website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a login ID or password, register at this URL:

http://tools.cisco.com/RPF/register/register.do

Opening a TAC Case

Using the online TAC Case Open Tool is the fastest way to open P3 and P4 cases. (P3 and P4 cases are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Case Open Tool automatically recommends resources for an immediate solution. If your issue is not resolved using the recommended resources, your case will be assigned to a Cisco TAC engineer. The online TAC Case Open Tool is located at this URL:

http://www.cisco.com/tac/caseopen

For P1 or P2 cases (P1 and P2 cases are those in which your production network is down or severely degraded) or if you do not have Internet access, contact Cisco TAC by telephone. Cisco TAC engineers are assigned immediately to P1 and P2 cases to help keep your business operations running smoothly.

To open a case by telephone, use one of the following numbers:

Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447

For a complete listing of Cisco TAC contacts, go to this URL:

http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

TAC Case Priority Definitions

To ensure that all cases are reported in a standard format, Cisco has established case priority definitions.

Priority 1 (P1)—Your network is "down" or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.

Priority 2 (P2)—Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.

Priority 3 (P3)—Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.

Priority 4 (P4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online and printed sources.

The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL:

http://www.cisco.com/en/US/products/products_catalog_links_launch.html

Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press online at this URL:

http://www.ciscopress.com

Packet magazine is the Cisco quarterly publication that provides the latest networking trends, technology breakthroughs, and Cisco products and solutions to help industry professionals get the most from their networking investment. Included are networking deployment and troubleshooting tips, configuration examples, customer case studies, tutorials and training, certification information, and links to numerous in-depth online resources. You can access Packet magazine at this URL:

http://www.cisco.com/packet

iQ Magazine is the Cisco bimonthly publication that delivers the latest information about Internet business strategies for executives. You can access iQ Magazine at this URL:

http://www.cisco.com/go/iqmagazine

Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:

http://www.cisco.com/en/US/about/ac123/ac147/about_cisco_the_internet_protocol_journal.html

Training—Cisco offers world-class networking training. Current offerings in network training are listed at this URL:

http://www.cisco.com/en/US/learning/index.html