Guest

Cisco ONS 15300 Series

Release Notes for Cisco ONS 15310-MA, Release 8.6.1

  • Viewing Options

  • PDF (111.2 KB)
  • Feedback
Release Notes for Cisco ONS 15310-MA Release 8.6.1

Table Of Contents

Release Notes for Cisco ONS 15310-MA
Release 8.6.1

About Release 8.6.1

Contents

Changes to the Release Notes

Caveats

Alarms

CSCtd60987—RFI-V alarm does not clear on ONS 15310 NEs in the CTM

Common Control Cards

CSCtb34677 - MultiRate PPM shows PROV-MISMATCH after rate change

CSCsy16814—Traffic is hit when port state is changed from OOS-DSBLD to IS

Optical I/O Cards

CSCsx13871—OC-3 PPM on 15310-MA node does not report PJ-Gen performance monitors

Maintenance and Administration

CSCsu33773—STS PM counters cannot be cleared on protect STS in BLSR switched state

Resolved Caveats for Release 8.6.1

Alarms

CSCsj26750—DS1_14 card shows Act (green) LED instead of Fail (red) LED

CSCsm92317—AIS alarm on the DS1 port is not suppressed

CSCsw42641—CTNEQPT-PBPROT alarm is reported when filler card is inserted in 310MA

CSCtc03705—Invalid CTNEQPT-PBROT alarm is raised

CSCsw45101—CONTBUS-IO alarm is reported when filler card is inserted in 310MA

CTC

CSCsk83405—Retrieval of OSPF diagnostics raises the OSPF Hello Fail alarm

CSCsq14054—CTC hangs when VCAT state changes from OOS,DSBLD to IS,AINS

Data I/O Cards

CSCso84751—LCAS members remain in LCAS Rx DNU alarm state after XC soft reset

CSCsu30587—VT members remain idle after trunk card is pulled multiple times

CSCsu02263—CTX hard reset causes GFP-LFD alarms, VCAT traffic stop flow to GT3

CSCsq83369—Traffic loss on CE-MR-6 card with single CTX soft reset

Hardware

CSCsl92447—Traffic in a split fiber circuit is dropped when the trunk port is shut down

CSCsu88198—15310 OSP (ANSI) fails GR1089 1. level 400V surge on DS1 ports

Maintenance and Administration

CSCsb88234—No plug-in message when a filler card is plugged in without prior provisioning

CSCsu62968—DS3 Port changes to IS from AINS state after soak expiry without valid input signal

Path Protection

CSCsl52122—Revertive path protection circuit may not switch to protected path during activation

TL1

CSCsu24438—RTRV-TH-MOD2 command for optical ports does not retrieve any value

New Features and Functionality

Related Documentation

Release-Specific Documents

Platform-Specific Documents

Obtaining Optical Networking Information

Where to Find Safety and Warning Information

Cisco Optical Networking Product Documentation CD-ROM

Obtaining Documentation and Submitting a Service Request


Release Notes for Cisco ONS 15310-MA
Release 8.6.1


OL-22859-01

July 2010

Release notes address closed (maintenance) issues, caveats, and new features for the Cisco ONS 15310-MA platform. For detailed information regarding features, capabilities, hardware, and software introduced with this release, refer to Release 8.5.1 version of the
Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide;
Release 8.5.1 version of the
Cisco ONS 15310-CL and Cisco ONS 15310-MA Reference Guide; and Release 8.5.1 version of the Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide and Release 8.5.1 version of the Cisco ONS SONET TL1 Command Guide. For the most current version of the Release Notes for Cisco ONS 15310-MA Release 8.6.1, see the following URL:

http://www.cisco.com/en/US/products/hw/optical/ps2001/prod_release_notes_list.html

Cisco also provides Bug Toolkit, a web resource for tracking defects. To access Bug Toolkit, see the following URL:

http://tools.cisco.com/Support/BugToolKit/action.do?hdnAction=searchBugs

About Release 8.6.1

Cisco ONS 15310-MA Release 8.6.1 does not include any new features.

Cisco ONS 15310-MA Release 8.6.1 is based on Cisco ONS 15310-MA Release 8.6. The Release Notes for Cisco ONS 15310-MA Release 8.6.1 contain closed (maintenance) issues and caveats found in Cisco ONS 15310-MA Release 8.6.1.

Contents

Changes to the Release Notes

Caveats

Resolved Caveats for Release 8.6.1

New Features and Functionality

Related Documentation

Obtaining Optical Networking Information

Obtaining Documentation and Submitting a Service Request

Changes to the Release Notes

This section documents supplemental information that has been added to the Release Notes for Cisco ONS 15454 Release 8.6.1 since the production of the Cisco ONS 15454 System Software CD for Release 8.6.1.

Caveats

Review the notes listed below before deploying the Cisco ONS 15454. Caveats with tracking numbers are known system limitations that are scheduled to be addressed in a subsequent release. Caveats without tracking numbers are provided to point out procedural or situational considerations when deploying the product.

Alarms

This section documents caveats for Alarms in Release 8.6.1.

CSCtd60987—RFI-V alarm does not clear on ONS 15310 NEs in the CTM

In Software Release 8.6.1, the RFI-V alarm does not clear on ONS 15310 NEs in the Cisco Transport Manager (CTM). The workaround is to modify the severity of the RFI-V of the logical objects VT-MON and VT-TERM in the alarm profile to the same value as a customized severity. After changing the MON and TERM severity to the same value the RFI-V alarm is cleared in the CTM/CTC. This issue will not be resolved.

Common Control Cards

This section documents caveats for Common Control Cards in Release 8.6.1.

CSCtb34677 - MultiRate PPM shows PROV-MISMATCH after rate change

The PROV-MISMATCH alarm is raised on the CTX-MA card when the optical rate of a port is changed without changing the reach. When the rate is changed, the reach does not get configured automatically. The workaround is to set the reach to "auto" before changing the rate.

CSCsy16814—Traffic is hit when port state is changed from OOS-DSBLD to IS

Traffic is hit when the port state is changed from OOS-DSBLD to IS. This issue is found in CE-MR-6 cards. The workaround is to perform IS->OOS-DSBLD->IS transition until the problem is fixed. This issue will be resolved in a future release.

Optical I/O Cards

This section documents caveats for Optical I/O Cards in Release 8.6.1.

CSCsx13871—OC-3 PPM on 15310-MA node does not report PJ-Gen performance monitors

PJ-Gen is not reported for OC-3-rated pluggable port modules (PPM) after you perform the following tasks:

1. Create an STS-1 circuit on an OC-3-rated PPM.

2. Enable IIPPM for the same circuit (on the same OC-3 PPM).

3. Enable PJStsMon on STS-1.

4. Create a frequency offset into this OC-3 PPM using testset. The same PJ-Gen is not reported in CTC/TL-1.

No workaround is available for this issue. This issue will not be resolved.

Maintenance and Administration

This section documents caveats for Maintenance and Administration in Release 8.6.1.


Caution VxWorks is intended for qualified Cisco personnel only. Use of VxWorks by customers is not recommended, nor is it supported by the Cisco Technical Assistance Center. Inappropriate use of VxWorks commands can have a negative and service-affecting impact on your network. Consult the troubleshooting guide for your release and platform for appropriate troubleshooting procedures. To exit without logging in, enter a Control-D (press the Control and D keys at the same time) at the Username prompt. To exit after logging in, type "logout" at the VxWorks shell prompt.


Note Cisco Transport Controller (CTC) does not support adding or creating more than five circuits in autoranged provisioning. This restriction is intentional.



Note In releases earlier than Cisco ONS Release 4.6, you could independently set proxy server gateway settings; however, with Cisco ONS Release 4.6.x and later, this is no longer the case. To retain the integrity of existing network configurations, settings made in a pre-4.6 release are not changed upon upgrading to Cisco ONS Release 7.x. Current settings are displayed in Cisco Transport Controller (whether they were inherited from an upgrade or they were set using the current GUI).


CSCsu33773—STS PM counters cannot be cleared on protect STS in BLSR switched state

STS PM counters cannot be cleared on protect STS in BLSR switched state. No workaround is available for this issue. This issue will not be resolved.

Resolved Caveats for Release 8.6.1

This section documents caveats resolved in Release 8.6.1.

Alarms

This section documents resolved caveats for Alarms in Release 8.6.1.

CSCsj26750—DS1_14 card shows Act (green) LED instead of Fail (red) LED

When the card type in Cisco Transport Controller is changed from DS1_14 to DS1_E1_56 with a DS1-14 physical card in the slot, the LED in the DS1_14 card will show Act (green), instead of Fail l (red). This issue has been resolved.

CSCsm92317—AIS alarm on the DS1 port is not suppressed

The AIS alarm on the DS1 port is not suppressed when the circuit is OOS, MT and the DS3 port is in service. This issue has been resolved.

CSCsw42641—CTNEQPT-PBPROT alarm is reported when filler card is inserted in 310MA

A CTNEQPT-PBPROT alarm is reported on a CE-100T card with a filler card in the slot of the CTXMA under the following conditions:

1. A CE-100T card is plugged into slot 1, 2, 5, or 6 with a filler card already present in slot 3 or 4.

2. The CTNEQPT-PBPROT alarm is raised after the CE-100T card or the CTXMA is reset.

This issue has been resolved.

CSCtc03705—Invalid CTNEQPT-PBROT alarm is raised

During the software upgrade from Release 7.23 to Release 9.01, the CTNEQPT-PBPROT alarm is reported on a CE-100T8 card with the CTX filler card inserted in the CTX-MA card slot. This issue has been resolved.

CSCsw45101—CONTBUS-IO alarm is reported when filler card is inserted in 310MA

A CONTBUS-IO-A alarm is reported on a CE-100T card with a filler card in slot 3.

A CONTBUS-IO-B alarm reported on CE-100T with a filler card in slot 4.

This issue occur under the following conditions:

1. A CE-100T card is plugged in into slot 1, 2, 5, or 6 with a filler card already present in slot 3 or 4.

2. The CONTBUS-CLK-A or the CONTBUS-CLK-B alarm is raised after the CE-100T card or the CTXMA is reset.

This issue has been resolved.

CTC

This section documents resolved caveats for CTC in Release 8.6.1

CSCsk83405—Retrieval of OSPF diagnostics raises the OSPF Hello Fail alarm

Performing a retrieval of OSPF diagnostic information from the CTC network raises the OSPF Hello Fail alarm and the controller card is locked. This issue has been resolved.

CSCsq14054—CTC hangs when VCAT state changes from OOS,DSBLD to IS,AINS

CTC hangs when the VCAT state transitions from OOS,DSBLD to IS,AINS. This issue has been resolved.

Data I/O Cards

This section documents resolved caveats for Data I/O Cards in Release 8.6.1.

CSCso84751—LCAS members remain in LCAS Rx DNU alarm state after XC soft reset

After XC soft resets on CE-MR-10 or CE-MR-6 cards, LCAS members may remain in an LCAS Rx DNU alarm state. This issue has been resolved.

CSCsu30587—VT members remain idle after trunk card is pulled multiple times

VT members remain idle on pulling truck cards multiple times. This issue has been resolved.

CSCsu02263—CTX hard reset causes GFP-LFD alarms, VCAT traffic stop flow to GT3

The GFP loss of frame delineation (GFP-LFD) alarm is reported on VC12 and VC3 VCAT circuits, causing loss of traffic to GT3, when the CTX card is hard reset.

This issue occurs under the following conditions:

1. In a three- node setup, configure the Cisco ONS 15310-MA node to directly derive timing from the BITS timed node. Set the remaining nodes to derive time from the Cisco ONS 15310-MA node.

2. Create VC12 and/or VC3 circuits on the Cisco ONS 15310-MA node.

3. Unplug the CTX card.

4. The GFP-LFD alarm is reported.


Note This issue is seen on the 310MA node only on transition from no CTX in the node to one CTX plugged into the node. The issue is not seen on a CTX hard- reset from CTC.


This issue has been resolved.

CSCsq83369—Traffic loss on CE-MR-6 card with single CTX soft reset

Traffic loss on a CE-MR-6 card with a single CTX soft reset occurs under the following condition:

On a 310MA node with a single CTX card, traffic loss (for approximately 15 seconds) on a CE-MR-6 card occurs with a single CTX soft-reset

This issue has been resolved.

Hardware

This section documents resolved caveats for Hardware in Release 8.6.1.

CSCsl92447—Traffic in a split fiber circuit is dropped when the trunk port is shut down

The traffic in a split fiber circuit is dropped when the trunk port is shut down either by pulling the trunk port fiber or setting the admin state as OOS-DSBLD, and performing a soft reset on an ML-MR card or a hard reset on a CE-MR-10 or CE-MR-6 card. This issue has been resolved.

CSCsu88198—15310 OSP (ANSI) fails GR1089 1. level 400V surge on DS1 ports

15310 OSP (ANSI) fails GR1089 1. level surge on DS1 ports under the following condition:

The surge level is 1,000 volts and 600,000 volts.

This issue has been resolved.

Maintenance and Administration

This section documents resolved caveats for Maintenance and Administration in Release 8.6.1.


Caution VxWorks is intended for qualified Cisco personnel only. Use of VxWorks by customers is not recommended, nor is it supported by the Cisco Technical Assistance Center. Inappropriate use of VxWorks commands can have a negative and service-affecting impact on your network. Consult the troubleshooting guide for your release and platform for appropriate troubleshooting procedures. To exit without logging in, enter a Control-D (press the Control and D keys at the same time) at the Username prompt. To exit after logging in, type "logout" at the VxWorks shell prompt.


Note Cisco Transport Controller (CTC) does not support adding or creating more than five circuits in autoranged provisioning. This restriction is intentional.



Note In releases earlier than Cisco ONS Release 4.6, you could independently set proxy server gateway settings; however, with Cisco ONS Release 4.6.x and later, this is no longer the case. To retain the integrity of existing network configurations, settings made in a pre-4.6 release are not changed upon upgrading to Cisco ONS Release 7.x. Current settings are displayed in Cisco Transport Controller (whether they were inherited from an upgrade or they were set using the current GUI).


CSCsb88234—No plug-in message when a filler card is plugged in without prior provisioning

When a card is provisioned and a filler card is plugged in, a DBCHG with ENT-EQPT alarm is raised, but when a filler card is plugged in without a prior provision there is no plug-in message. Similarly, there is no message upon removal of the filler card. This issue has been resolved release.

CSCsu62968—DS3 Port changes to IS from AINS state after soak expiry without valid input signal

DS3 ports of DS1-28/DS3-EC1-3 and DS1-84/DS3-EC1-3 cards changes from AINS to IS state after an AINS soak time expiry without a valid input signal. This issue has been resolved.

Path Protection

This section documents resolved caveats for Path Protection in Release 8.6.1.

CSCsl52122—Revertive path protection circuit may not switch to protected path during activation

A revertive path protection circuit may not switch to protected path during activation when the path protection selector does not detect the working path as Active even if that path has errors. This issue will be resolved in a future release.

TL1

This section documents resolved caveats for TL1 in Release 8.6.


Note To be compatible with TL1 and DNS, all nodes must have valid names. Node names should contain alphanumeric characters or hyphens, but no special characters or spaces.


CSCsu24438—RTRV-TH-MOD2 command for optical ports does not retrieve any value

The RTRV-TH-MOD2 command for optical ports does not retrieve any value when the MONTYPE specified in the command is "ALL" with the FEND location, and returns the error "/* Far End Performance Monitoring Values Not Supported */." This issue has been resolved.

New Features and Functionality

No new software features are included in Release 8.6.1.

Related Documentation

This section lists release-specific and platform-specific documents.

Release-Specific Documents

Release Notes for the Cisco ONS 15454, Release 8.6

Release Notes for the Cisco ONS 15454 SDH, Release 8.6

Release Notes for the Cisco ONS 15310-CL, Release 8.6

Release Notes for the Cisco ONS 15454, Release 8.6.1

Release Notes for the Cisco ONS 15454 SDH, Release 8.6.1

Release Notes for the Cisco ONS 15310-CL, Release 8.6.1

Platform-Specific Documents

Cisco ONS 15454 Release 8.6.1 is based on Cisco ONS 15454 Release 8.6. Refer to the Release 8.5.1 documents for more information.

Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide
Provides installation, turn up, test, and maintenance procedures

Cisco ONS 15310-CL and Cisco ONS 15310-MA Reference Manual
Provides technical reference information for cards, nodes, and networks

Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide
Provides a list of SONET alarms and troubleshooting procedures, general troubleshooting information, transient conditions, and error messages

Cisco ONS SONET TL1 Command Guide
Provides a comprehensive list of TL1 commands

Cisco ONS SONET TL1 Reference Guide
Provides general information, procedures, and errors for TL1

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide
Provides software feature and operation information for Ethernet cards

Cisco ONS 15454 Software Upgrade Guide, Release 8.5.x

Obtaining Optical Networking Information

This section contains information that is specific to optical networking products. For information that pertains to all of Cisco, refer to the Obtaining Documentation and Submitting a Service Request section.

Where to Find Safety and Warning Information

For safety and warning information, refer to the Cisco Optical Transport Products Safety and Compliance Information document that accompanied the product. This publication describes the international agency compliance and safety information for the Cisco ONS 15454 system. It also includes translations of the safety warnings that appear in the ONS 15454 system documentation.

Cisco Optical Networking Product Documentation CD-ROM

Optical networking-related documentation, including Cisco ONS 15xxx product documentation, is available in a CD-ROM package that ships with your product. The Optical Networking Product Documentation CD-ROM is updated periodically and may be more current than printed documentation.

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.