Cisco ONS 15454 DWDM Reference Manual, Release 9.2
Appendix A, Hardware Specifications
Downloads: This chapterpdf (PDF - 1.44MB) The complete bookPDF (PDF - 24.06MB) | Feedback

Hardware Specifications

Table Of Contents

Hardware Specifications

A.1  ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelf Specifications

A.2  General Card Specifications

A.2.1  Power

A.2.2  Temperature

A.3  Common Control Card Specifications

A.3.1  TCC2 Card Specifications

A.3.2  TCC2P Card Specifications

A.3.3  TCC3 Card Specifications

A.3.4  TNC Card Specifications (Cisco ONS 15454 M2 and Cisco ONS 15454 M6)

A.3.5  TSC Card Specifications (ONS 15454 M2 and ONS 15454 M6)

A.3.6  AIC-I Card Specifications

A.3.7  AEP Specifications (ANSI only)

A.3.8  MIC-A/P FMEC Specifications (ETSI only)

A.3.9  MIC-C/T/P FMEC Specifications (ETSI only)

A.3.10  MS-ISC-100T Card Specifications

A.4  Optical Service Channel Cards

A.4.1  OSCM Card Specifications

A.4.2  OSC-CSM Card Specifications

A.5  Optical Amplifier Cards

A.5.1  OPT-PRE Amplifier Card Specifications

A.5.2  OPT-BST Amplifier Card Specifications

A.5.3  OPT-BST-E Amplifier Card Specifications

A.5.4  OPT-BST-L Amplifier Card Specifications

A.5.5  OPT-AMP-L Preamplifier Card Specifications

A.5.6  OPT-AMP-17-C Amplifier Card Specifications

A.5.7  OPT-AMP-C Amplifier Card Specifications

A.5.8  OPT-RAMP-C Amplifier Card Specifications

A.5.9  OPT-RAMP-CE Amplifier Card Specifications

A.6  PSM (Protection Switching Module) Card Specifications

A.7  Multiplexer and Demultiplexer Cards

A.7.1  32MUX-O Card Specifications

A.7.2  32DMX-O Card Specifications

A.7.3  4MD-xx.x Card Specifications

A.8  Reconfigurable Optical Add/Drop Cards

A.8.1  32DMX Card Specifications

A.8.2  32DMX-L Card Specifications

A.8.3  32WSS Card Specifications

A.8.4  32WSS-L Card Specifications

A.8.5  40-MUX-C Card Specifications

A.8.6  40-DMX-C Card Specifications

A.8.7  40-DMX-CE Card Specifications

A.8.8  40-WSS-C Card Specifications

A.8.9  40-WSS-CE Card Specifications

A.8.10  40-WXC-C Card Specifications

A.8.11  80-WXC-C Card Specifications

A.8.12  40-SMR1-C Card Specifications

A.8.13  40-SMR2-C Card Specifications

A.8.14  MMU Card Specifications

A.9  Optical Add/Drop Cards

A.9.1  AD-1C-xx.x Card Specifications

A.9.2  AD-2C-xx.x Card Specifications

A.9.3  AD-4C-xx.x Card Specifications

A.9.4  AD-1B-xx.x Card Specifications

A.9.5  AD-4B-xx.x Card Specifications

A.10  Transponder and Muxponder Card Specifications

A.10.1  TXP_MR_10G Card Specifications

A.10.2  MXP_2.5G_10G Card Specifications

A.10.3  TXP_MR_2.5G and TXPP_MR_2.5G Card Specifications

A.10.4  MXP_MR_2.5G and MXPP_MR_2.5G Card Specifications

A.10.5  MXP_2.5G_10E Card Specifications

A.10.6  MXP_2.5G_10E_C Card Specifications

A.10.7  MXP_2.5G_10E_L Card Specifications

A.10.8  MXP_2.5G_10EX_C Card Specifications

A.10.9  MXP_MR_10DME_C Card Specifications

A.10.10  MXP_MR_10DME_L Card Specifications

A.10.11  MXP_MR_10DMEX_C Card Specifications

A.10.12  TXP_MR_10E Card Specifications

A.10.13  TXP_MR_10E_C Card Specifications

A.10.14  TXP_MR_10E_L Card Specifications

A.10.15  TXP_MR_10EX_C Card Specifications

A.10.16  40G-MXP-C Card Specifications

A.10.17  ADM-10G Card Specifications

A.10.18  GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Card Specifications

A.10.19  OTU2_XP Card Specifications

A.11  TDC-CC and TDC-FC Card Specifications

A.12  Mesh Patch Panel Specifications

A.12.1  PP-MESH-4 Patch Panel Specifications

A.12.2  PP-MESH-8 Patch Panel Specifications

A.12.3  15454-PP-4-SMR Patch Panel Specifications

A.13  SFP and XFP Specifications

A.14  Patch Panel Specifications


Hardware Specifications


This appendix contains hardware and software specifications for the ONS 15454 ANSI and ETSI shelf assemblies and cards.


Note Unless otherwise specified, "ONS 15454" refers to both ANSI and ETSI shelf assemblies.


The following sections are included:

ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelf Specifications

General Card Specifications

Common Control Card Specifications

Optical Service Channel Cards

Optical Amplifier Cards

PSM (Protection Switching Module) Card Specifications

Multiplexer and Demultiplexer Cards

Reconfigurable Optical Add/Drop Cards

Optical Add/Drop Cards

Transponder and Muxponder Card Specifications

TDC-CC and TDC-FC Card Specifications

Mesh Patch Panel Specifications

SFP and XFP Specifications

Patch Panel Specifications

A.1  ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelf Specifications

For information on shelf bandwidth; list of topologies; Cisco Transport Controller (CTC) specifications; the LAN, Transaction Language One (TL1), modem, and alarm specifications; timing, power, and environmental specifications; and shelf dimensions, refer to Appendix A, Hardware Specifications" in the "Cisco ONS 15454 Hardware Installation Guide".

A.2  General Card Specifications

This section provides power specifications and temperature ranges for all ONS 15454 cards.

A.2.1  Power

Table A-1 provides power consumption information for the ONS 15454 cards.

Table A-1 Individual Card Power Requirements

Card Type
Card Name 
Maximum Power in Watts
Typical Power in Watts
Amperes at -48 V
BTU/Hr.
Common Control Cards

TCC2/TCC2P/TCC3

30

19.2

0.54

89

TNC

62

52

0.94

153

TSC

55

46

0.79

129

AIC-I

10

6

0.17

28

AEP

-

-

(from +5 VDC from AIC-I)

10

MIC-A/P

0.2

0.13

via TCC2/TCC2P/TCC3

0.44

MIC-C/T/P

0.5

0.38

via TCC2/TCC2P/TCC3

1.29

MS-ISC-100T

69

53

1.10

181.0

Optical Service Channel Cards

OSCM

26

23

0.48

79

OSC-CSM

27

24

0.5

82

Optical Amplifier Cards

OPT-PRE

39

30

0.63

103

OPT-BST

39

30

0.63

103

OPT-BST-E

39

30

0.63

103

OPT-BST-L

32

25

0.52

86

OPT-AMP-L

40

32

0.67

110

OPT-AMP-17-C

23

19

0.83

137

OPT-AMP-C

30

23

0.83

137

OPT-RAMP-C

55

44

1.04

171

OPT-RAMP-CE

58

46

0.83

137

PSM Card

PSM

50

35

0.41

69

Multiplexer and Demultiplexer Cards

32MUX-O

25

16

0.33

55

32DMX-O

25

16

0.33

55

4MD-xx.x

25

17

0.35

58.0

ROADM Cards

32DMX

25

15

0.31

52

32DMX-L

25

15

0.31

52

32WSS

65

50

1.04

171

32WSS-L

48

43

0.90

147

40-MUX-C

39

35

0.73

120

40-DMX-C

39

35

0.73

120

40-DMX-CE

39

35

0.73

120

40-WSS-C

79

63

1.53

250

40-WSS-CE

79

63

1.53

250

40-WXC-C

33

30

0.63

103

80-WXC-C

40

20

0.42

69

40-SMR1-C

60

30

0.73

120

40-SMR2-C

70

35

0.83

137

MMU

15

7

0.15

24

Optical Add/Drop Cards

AD-1C-xx.x

25

17

0.35

58.0

AD-2C-xx.x

25

17

0.35

58.0

AD-4C-xx.x

25

17

0.35

58.0

AD-1B-xx.x

25

17

0.35

58.0

AD-4B-xx.x

25

17

0.35

58.0

Transponder and Muxponder Cards

TXP_MR_10G

50

32.5

0.73

120

TXP_MR_10E

50

32.5

1.05

171

TXP_MR_10E_C

50

31.8

1.05

171

TXP_MR_10E_L

50

31.8

1.05

171

TXP_MR_10EX_C

53

34.4

0.88

144

TXP_MR_2.5G

31

24.3

0.73

120

TXPP_MR_2.5G

31

24.3

1.05

171

MXP_2.5G_10G

60

43.6

1.05

171

MXP_2.5G_10E

60

43.6

1.05

171

MXP_2.5G_10E_C

60

43.6

1.05

171

MXP_2.5G_10E_L

60

43.6

1.05

171

MXP_2.5G_10EX_C

60

43.6

1.05

171

MXP_MR_2.5G

60

43.6

1.05

171

MXPP_MR_2.5G

60

43.6

1.05

171

Transponder and Muxponder Cards

MXP_MR_10DME_C

71

53.4

1.25

205

MXP_MR_10DME_L

71

53.4

1.25

205

MXP_MR_10DMEX_C

74

56

1.25

205

40G-MXP-C

112

90

2.34

383

ADM-10G

160

135

2.81

461

OTU2_XP

70

50.8

1.48

243

TDCU Cards

TDC-CC

12

11

0.17

28

TDC-FC

12

11

0.17

28


A.2.2  Temperature

Operating temperature:

Long term: 0 to 40 degrees Celsius (32 to 104 degrees Fahrenheit)

Short term: Functionality is guaranteed at -5 to 55 degrees Celsius (23 to 131 degrees Fahrenheit), according to GR-63 Issue 3

The indicated temperatures are the ambient ones in which the shelf can be placed.

A.3  Common Control Card Specifications

This section provides specifications for the TCC2, TCC2P, TCC3, TNC, TSC, AIC, and AIC-I cards, the alarm expansion panel (AEP), the MIC-A/P and MIC-C/T/P FMECs, and the MS-ISC-100T card.

For compliance information, refer to the Cisco Optical Transport Products Safety and Compliance Information document.

A.3.1  TCC2 Card Specifications

The TCC2 card has the following specifications:

CTC software

Interface: EIA/TIA-232 (local craft access, on TCC2 faceplate)

Interface: 10BaseT LAN (on TCC2 faceplate)

Interface: 10BaseT LAN (through the backplane)

Synchronization

Stratum 3, per Telcordia GR-253-CORE

Free running access: Accuracy +/- 4.6 ppm

Holdover stability: 3.7 x 10-7 per day including temperature (< 255 slips in first 24 hours)

Reference: External BITS, line, internal

Supply voltage monitoring

Both supply voltage inputs are monitored.

Normal operation: -40.5 to -56.7 V

Undervoltage: Major alarm

Overvoltage: Major alarm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 235 mm (9.250 in.)

Weight not including clam shell: 0.7 kg (1.5 lb)

A.3.2  TCC2P Card Specifications

The TCC2P card has the following specifications:

CTC software

Interface: EIA/TIA-232 (local craft access, on TCC2P faceplate)

Interface: 10BaseT LAN (on TCC2P faceplate)

Interface: 10BaseT LAN (through the backplane)

Synchronization

Stratum 3, per Telcordia GR-253-CORE

Free running access: Accuracy +/- 4.6 ppm

Holdover stability: 3.7 * 10 exp - 7 per day including temperature (< 255 slips in first 24 hours)

Reference: External BITS, line, internal

Supply voltage monitoring

Both supply voltage inputs are monitored.

Normal operation: -40.5 to -56.7 V (in -48 VDC systems)

Undervoltage: Major alarm

Overvoltage: Major alarm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 1.5 lb (0.7 kg)

A.3.3  TCC3 Card Specifications

The TCC3 card has the following specifications:

CTC software

Interface: EIA/TIA-232 (local craft access, on TCC3 faceplate)

Interface: 10BaseT LAN (on TCC3 faceplate)

Interface: 10BaseT LAN (through the backplane)

Synchronization

Stratum 3, per Telcordia GR-253-CORE

Free running access: Accuracy +/- 4.6 ppm

Holdover stability: 3.7 * 10 exp - 7 per day including temperature (< 255 slips in first 24 hours)

Reference: External BITS, line, internal

Supply voltage monitoring

Both supply voltage inputs are monitored.

Normal operation: -40.5 to -56.7 V (in -48 VDC systems)

Undervoltage: Major alarm

Overvoltage: Major alarm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 1.5 lb (0.7 kg)

A.3.4  TNC Card Specifications (Cisco ONS 15454 M2 and Cisco ONS 15454 M6)

The TNC card has the following specifications:

CTC software

Interface: EIA/TIA-232 (local craft access, on TNC faceplate)

Interface: 10BaseT LAN (on TNC faceplate)

Interface: 10BaseT LAN (through the external connection unit for EMS, CT, MSM, VoIP, UDC and Line Cards)

Two SFP interfaces to support Optical Service Channels (OC-3/STM-1 or FE/GE)

Synchronization

Stratum 3, per Telcordia GR-253-CORE

Free running access: Accuracy +/- 4.6 ppm

Holdover stability: 3.7 * 10 exp - 7 per day including temperature (< 255 slips in first 24 hours)

Reference: External BITS, line, internal

Supply voltage monitoring

Both the input supply voltages are monitored.

Normal operation: -40.5 to -56.7 V (in -48 VDC systems)

AC input voltage range: Undervoltage TH 90V histeresis 5V; Overvoltage TH 254V histeresis 10V

Undervoltage: Major alarm

Overvoltage: Major alarm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 1.6 lb (0.8 kg)

A.3.5  TSC Card Specifications (ONS 15454 M2 and ONS 15454 M6)

The TSC card has the following specifications:

CTC software

Interface: EIA/TIA-232 (local craft access, on TSC faceplate)

Interface: 10BaseT LAN (on TSC faceplate)

Interface: 10BaseT LAN (through the external connection unit for EMS, CT, MSM, VoIP, UDC and Line Cards)

Synchronization

Stratum 3, per Telcordia GR-253-CORE

Free running access: Accuracy +/- 4.6 ppm

Holdover stability: 3.7 * 10 exp - 7 per day including temperature (< 255 slips in first 24 hours)

Reference: External BITS, line, internal

Supply voltage monitoring

Both the input supply voltages are monitored.

Normal operation: -40.5 to -56.7 V (in -48 VDC systems)

AC input voltage range: Undervoltage TH 90V histeresis 5V; Overvoltage TH 254V histeresis 10V

Undervoltage: Major alarm

Overvoltage: Major alarm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 1.6 lb (0.8 kg)

A.3.6  AIC-I Card Specifications

The AIC-I card has the following specifications:

Alarm inputs

Number of inputs: 12 without AEP, 32 with AEP

Opto-coupler isolated

Label customer provisionable

Severity customer provisionable

Common 32 V output for all alarm inputs

Each input limited to 2 mA

Termination: Wire-wrap on backplane without AEP, on AEP connectors with AEP

Alarm outputs

Number of outputs: 4 (user configurable as inputs) without AEP, 16 with AEP

Switched by opto MOS (metal oxide semiconductor)

Triggered by definable alarm condition

Maximum allowed open circuit voltage: 60 VDC

Maximum allowed closed circuit current: 100 mA

Termination: Wire-wrap on backplane without AEP, on AEP connectors with AEP

Express orderwire/local orderwire (EOW/LOW)

ITU-T G.711, ITU-T G.712, Telcordia GR-253-CORE

A-law, mu-law


Note Due to the nature of mixed coding, in a mixed-mode (A-law/mu-law) configuration, the orderwire is not ITU-T G.712 compliant.


Orderwire party line

Dual tone, multifrequency (DTMF) signaling

User data channel (UDC)

Bit rate: 64 kbps, codirectional

ITU-T G.703

Input/output impedance: 120 ohm

Termination: RJ-11 connectors

Data communications channel (DCC)

Bit rate: 576 kbps

EIA/TIA-485/V11

Input/output impedance: 120 ohm

Termination: RJ-45 connectors

ACC connection for additional alarm interfaces

Connection to AEP

Power monitoring alarming states:

Power failure (0 to -38 VDC)

Undervoltage (-38 to -40.5 VDC)

Overvoltage (beyond -56.7 VDC)

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Weight: 1.8 lb (0.82 kg)

A.3.7  AEP Specifications (ANSI only)

The AEP has the following specifications:

Alarm inputs

Number of inputs: 32

Optocoupler isolated

Label customer provisionable

Severity customer provisionable

Common 32 V output for all alarm inputs

Each input limited to 2 mA

Termination: 50-pin AMP champ connector

Alarm outputs

Number of outputs: 16

Switched by opto MOS

Triggered by definable alarm condition

Maximum allowed open circuit voltage: 60 VDC

Maximum allowed closed circuit current: 100 mA

Termination: 50-pin AMP champ connector

Environmental

Overvoltage protection: as in ITU-T G.703 Annex B

Dimensions of AEP board

Height: 20 mm (0.79 in.)

Width: 330 mm (13.0 in.)

Depth: 89 mm (3.5 in.)

Weight: 0.18 kg (0.4 lb)

A.3.8  MIC-A/P FMEC Specifications (ETSI only)

The MIC-A/P FMEC card has the following specifications:

Power supply input BATTERY B

System supply voltage: Nominal -48 VDC
Tolerance limits: -40.5 to -57.0 VDC

Connector: 3WK3 Combo-D power cable connector

Alarm outputs

Voltage (open contact): Maximum 60 VDC

Current (closed contact): Maximum 250 mA

Connector: 62-pin DB connector (common for inputs/outputs)

Alarm inputs

Voltage (open contact): Maximum 60 VDC

Current (closed contact): Maximum 2 mA

Connector: 62-pin DB connector (common for inputs/outputs)

Dimensions

Height: 182 mm (7.165 in.)

Width: 31.88 mm (1.255 in.)

Depth: 92 mm (3.62 in.)

Depth with backplane connector: 98 mm (3.87 in.)

Weight not including clam shell: 0.2 kg (0.5 lb)

A.3.9  MIC-C/T/P FMEC Specifications (ETSI only)

The MIC-C/T/P FMEC card has the following specifications:

Power supply input BATTERY A

System supply voltage: Nominal -48 VDC
Tolerance limits: -40.5 to -57.0 VDC

Connector: 3WK3 Combo-D power cable connector

Timing connector

Frequency: 2.048 MHz +/-10 ppm

Signal level: 0.75 to 1.5 V

Impedance: 75 ohms +/-5 percent (switchable by jumper to high impedance > 3 kohms)


Note 120 ohms balanced impedance is possible with external matching cable.


Cable attenuation: Up to 6 dB at 2 MHz

Connectors: 1.0/2.3 miniature coax connector

System management serial port:

System management serial port craft interface

Modem port (for future use)

Connectors: 8-pin RJ-45

System management LAN port connectors:

Signal: IEEE 802.3 10BaseT

Connectors: 8-pin RJ-45

Dimensions

Height: 182 mm (7.165 in.)

Width: 31.88 mm (1.255 in.)

Depth: 92 mm (3.62 in.)

Depth with backplane connector: 98 mm (3.87 in.)

Weight not including clam shell: 0.2 kg (0.5 lb)

A.3.10  MS-ISC-100T Card Specifications

The MS-ISC-100T card has the following specifications:

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 2.3 lb (1.0 kg)

A.4  Optical Service Channel Cards

This section provides specifications for the OSCM and OSC-CSM cards.

A.4.1  OSCM Card Specifications

The OSCM card has the following specifications:

Line

Bit rate: 155 Mbps

Code: Scrambled non-return to zero (NRZ)

Loopback modes: None

Connector: Duplex LC

Transmitter optical service channel (OSC) signal

Maximum transmitter output power: -1 dBm

Minimum transmitter output power: -5 dBm

Nominal wavelength: 1510-nm +/-10 nm

Variable optical attenuator (VOA) necessary in the transmit path to adjust the in-fiber optical power level

Receiver OSC signal

Maximum receiver level: -8 dBm at 10-10 bit error rate (BER)

Minimum receiver level: -40 dBm at 10-10 BER

Span budget: 40-dB span budget (about 150 km assuming fiber path loss equals 0.25 dB/km)

Jitter tolerance: Telcordia GR-253/G.823 compliant

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

A.4.2  OSC-CSM Card Specifications

The OSC-CSM card has the following specifications:

Line

Bit rate: 155 Mbps

Code: Scrambled NRZ

Loopback modes: None

Connector: Duplex LC

Transmitter OSC signal

Maximum transmitter output power: -2 dBm

Minimum transmitter output power: -24 dBm

Nominal wavelength: 1510-nm +/-10 nm

VOA is necessary in the transmit path to adjust the in-fiber optical power level

Receiver OSC signal

Maximum receiver level: -8 dBm at 10-10 BER

Minimum receiver level: -40 dBm at 10-10 BER

Span loss budget: 35-dB span budget (approximately 140 km assuming that the fiber path loss is equal to 0.25 dB/km)

Jitter tolerance: Telcordia GR-253/G.823 compliant

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

A.5  Optical Amplifier Cards

This section provides specifications for the OPT-PRE amplifier, OPT-BST amplifier, OPT-BST-E amplifier, OPT-BST-L amplifier, OPT-AMP-L preamplifier (configurable as a preamplifier or booster amplifier), OPT-AMP-C amplifier (configurable as a preamplifier or booster amplifier), OPT-AMP-17-C, and OPT-RAMP-C amplifier cards.

A.5.1  OPT-PRE Amplifier Card Specifications

The OPT-PRE amplifier card has the following specifications:

Optical characteristics:

Total operating wavelength range: 1530 to 1561.3 nm

Gain ripple (peak to valley): 1.5 dB

Mid-access loss (MAL) range (for dispersion compensation unit [DCU]): 3 to 9 dB

Gain range: 5 to 38.5 dBm in constant power mode, 5 to 28 dBm in constant gain mode

Minimum gain (standard range): 5.0 dBm

Maximum gain (standard range with programmable gain tilt): 21 dBm

Maximum gain (extended range with uncontrolled gain tilt): 38.5 dBm

Gain and power regulation over/undershoot: 0.5 dB

Limited maximum output power: 17.5 dBm

Maximum output power (with full channel load): 17 dB

Minimum output power (with one channel): -2 dBm

Input power (Pin) range at full channel load: -21.5 to 12 dBm

Input power (Pin) range at single channel load: -39.5 to -6 dBm

Noise figure at G3 21 dB = 6.5 dB

OSC filter drop (channels) insertion loss maximum: 1 dB

OSC filter drop (OSC) insertion loss maximum: 1.8 dB

OSC filter add (OSC) insertion loss maximum: 1.3 dB

Optical connectors: LC-UPC/2

Dimensions

Height: 12.65 in. (332 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (240 mm)

A.5.2  OPT-BST Amplifier Card Specifications

The OPT-BST amplifier card has the following specifications:

Optical characteristics:

Total operating wavelength range: 1530 to 1561.3 nm

Gain ripple (peak to valley): 1.5 dB

Gain range: 5 to 20 dBm with programmable gain tilt

Gain and power regulation over/undershoot: 0.5 dB

Limited maximum output power: 17.5 dBm

Maximum output power (with full channel load): 17 dB

Minimum output power (with one channel): -2 dBm

Input power (Pin) range at full channel load: -3 to 12 dBm

Input power (Pin) range at single channel load: -21 to -6 dBm

Noise figure at G3 20 dB = 6 dB

OSC filter drop (channels) insertion loss maximum: 1 dB

OSC filter drop (OSC) insertion loss maximum: 1.8 dB

OSC filter add (OSC) insertion loss maximum: 1.3 dB

Optical connectors: LC-UPC/2

Dimensions

Height: 12.65 in. (332 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (240 mm)

A.5.3  OPT-BST-E Amplifier Card Specifications

The OPT-BST-E amplifier card has the following specifications:

Optical characteristics:

Total operating wavelength range: 1530 to 1561.3 nm

Gain ripple (peak to valley): 1.8 dB

Gain range: 8 to 23 dB with programmable gain tilt

Extended gain range: 23 to 26 dB with gain tilt uncontrolled

Gain and power regulation over/undershoot: 0.5 dB

Limited maximum output power: 20.5 dBm

Maximum output power (with full channel load): 20 dB

Minimum output power (with one channel): -0 dBm

Input power (Pin) range at full channel load: -6 to 12 dBm

Input power (Pin) range at single channel load: -26 to -8 dBm

Noise figure at G3 23 dB = 6 dB

OSC filter drop (channels) insertion loss maximum: 1 dB

OSC filter drop (OSC) insertion loss maximum: 1.8 dB

OSC filter add (OSC) insertion loss maximum: 1.3 dB

Optical connectors: LC-UPC/2

Dimensions

Height: 12.65 in. (332 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (240 mm)

A.5.4  OPT-BST-L Amplifier Card Specifications

The OPT-BST-L amplifier card has the following specifications:

Optical characteristics:

Total operating wavelength range: 1570.0 to 1605.0 nm

Gain ripple (peak to valley): 1.5 dB

Gain range: 8 to 20 dB with programmable gain tilt

Extended gain range: 20 to 27 dB with gain tilt uncontrolled

Gain and power regulation over/undershoot: 0.5 dB

Limited maximum output power: 10 dBm

Maximum output power (with full channel load): 17 dB

Minimum output power (with one channel): -1 dBm

Input power (Pin) range at full channel load: -10 to 9 dBm

Input power (Pin) range at single channel load: -37 to -18 dBm

Noise figure at G3 20 dB = 7.5 dB

Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB

Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB

Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB

Optical connectors: LC-UPC/2

Dimensions

Height: 12.65 in. (332 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (240 mm)

A.5.5  OPT-AMP-L Preamplifier Card Specifications

The OPT-AMP-L card has the following specifications:

Optical characteristics:

DWDM channel wavelength plan, 100 GHz, 4 skip 1, ITU-T wavelength grid channels 71 (1602.3 nm) to 90 (1570.4 nm)

DWDM channel wavelength plan, 50 GHz, 8 skip 2, ITU-T wavelength grid channels 70.5 (1602.7 nm) to 90 (1570.4 nm)

Channel spacing: 100 and 50 GHz

Total operating wavelength range 1570.0 - 1605.0 nm

Gain ripple (peak to valley): 1.5 dB

Standard gain range: 12 to 24 dB

Extended gain range (uncontrolled gain tilt): 24 to 35 dB

Gain and power regulation over/undershoot: 0.5 dB

Minimum output power (with one channel): +2 dBm

Maximum power output (standard or extended gain range): 20 dB

Input power range (full channel load): -15 to 8 dB

Input power range (single channel load): -40 to -17

Noise figure at G3 20 dB = 8.9 dB

Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB

Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB

Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB

Optical connectors: LC-UPC/2

Dimensions

Height: 12.65 in. (332 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (240 mm)

A.5.6  OPT-AMP-17-C Amplifier Card Specifications

The OPT-AMP-17-C card has the following specifications:

Optical characteristics:

DWDM channel wavelength plan: 80 channels at 50 GHz spacing, 1530.33 nm to 1561.83 nm

Channel spacing: 50 GHz

Total operating wavelength range 1529.0 to 1562.5 nm

Gain ripple (peak to valley): 1.5 dB

Gain range: 14 to 23 dB

Optimal gain (gain tilt = 0): 17 dB

Gain and power regulation over/undershoot: 0.5 dB

Minimum output power (with one channel): -2 dBm

Maximum power output (standard or extended gain range): 17.5 dBm

Input power range (full channel load): -6 to 3 dBm

Input power range (single channel load): -28 to -19 dBm

Noise figure at G=17dB = 6 dB maximum

Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB

Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB

Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB

Optical connectors: LC-UPC/2

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

A.5.7  OPT-AMP-C Amplifier Card Specifications

The OPT-AMP-C amplifier card has the following specifications:

Optical characteristics:

Total operating wavelength range: 1529.0 to 1562.5 nm

Gain ripple (peak to valley): 1.2 dB

Gain range: 12 to 24 dB with programmable gain tilt

Extended gain range: 24 to 35 dB with gain tilt uncontrolled

Gain and power regulation over/undershoot: 0.5 dB

Limited maximum output power: 20.5 dBm

Maximum output power (with full channel load): 20 dBm

Minimum output power (with one channel): -2 dBm

Input power (Pin) at full channel load: -15 dBm minimum

Input power (Pin) range at single channel load: -40 to -17 dBm

Noise figure at G3 20 dB: 7.6 dB

Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB

Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB

Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB

Optical connectors: LC-UPC/2

Dimensions

Height: 12.65 in. (332 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 8.66 in. (220.1 mm)

A.5.8  OPT-RAMP-C Amplifier Card Specifications

The OPT-RAMP-C amplifier card has the following specifications:

Raman pump

Raman pump 1 wavelength: 1425 nm

Raman pump 2 wavelength: 1452 nm

Total Raman Pump power - Line-RX port: 500 mW

Operating range Raman Pump power - Line-RX port: min 100 mW, max 4502 mW

Raman pump laser class: 3B

Embedded EDFA

Total operating signal wavelength range: 1529 to 1562.5 nm

EDFA nominal gain value (Line RX to DC-TX): 14 dB

EDFA gain settable range: 8 to 20 dB

EDFA Output Power range - DC-TX (Full Channel load): 17.53 dBm

VOA attenuation range: 0 to 25 dB

Gain and power regulation over/undershoot: 0.5 dB

EDFA laser class: 1M

Maximum EDFA output power: 17.5 dBm

Minimum output power (with one channel): -10 dBm

Input power (Pin) at full channel load: -3 dBm to +9 dBm

Input power (Pin) range at single channel load: -24dBm to -10 dBm

Noise figure at G 14 dB: 7.5 dB

Insertion loss (Line TX to OSC TX): 0.3 to 2.0 dB

Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB

Insertion loss (OSC RX to LINE RX): 0.3 to 1.8 dB

Optical connectors: LC-UPC/2

Dimensions

Height: 12.65 in. (332 mm)

Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)

Depth: 8.665 in. (220.1 mm)

A.5.9  OPT-RAMP-CE Amplifier Card Specifications

The OPT-RAMP-CE amplifier card has the following specifications:

Raman pump

Raman pump 1 wavelength: 1425 nm

Raman pump 2 wavelength: 1452 nm

Total Raman pump power - LINE-RX port: 500 mW

Operating range Raman pump power - LINE-RX port: min 100 mW, max 450 mW

Raman pump laser class: 3B

Embedded EDFA

Total operating signal wavelength range: 1529 to 1562.5 nm

EDFA nominal gain value (LINE-RX to DC-TX): 11 dB

EDFA gain settable range: 5 to 17 dB

EDFA Output power range - DC-TX (Full Channel load): 20.2 dBm

VOA attenuation range: 0 to 25 dB

Gain and power regulation over/undershoot: 0.5 dB

EDFA laser class: 1M

Maximum EDFA output power: 20.5 dBm

Minimum output power (with one channel): -10 dBm

Input power (Pin) at full channel load: 15 dBm (maximum)

Input power (Pin) range at single channel load: -27dBm (minimum)

Noise figure at G 11 dB: 7 dB

Insertion loss (LINE-RX to MON-RX):22 to 26 dB

Insertion loss (LINE-TX to OSC-TX): 1.5 dB

Insertion loss (OSC-RX to LINE-RX): 0.7 to 1.7 dB

Insertion loss (LINE-TX to COM-RX): 0.6 to 1.0 dB

Insertion loss (LINE-TX to PD12): 1.7dB

Insertion loss (OSC-RX to LINE-RX): 0.7 to 1.7dB

Optical connectors: LC-UPC/2

Dimensions

Height: 13.11 in. (333 mm)

Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.88 in. (251 mm)

A.6  PSM (Protection Switching Module) Card Specifications

The PSM card has the following specifications:

Wavelength:

Total operating signal wavelength range (C-band range): 1529.0 - 1562.5 nm

OSC wavelength range: 1500 - 1520 nm

L-band range: 1570 - 1605 nm

Optical

Insertion loss:

COM-RX to W-TX and P-TX: 4.6 dB

W-RX and P-RX to COM-TX: 2.3 dB

Insertion loss ripple: 0.2 dB

Maximum optical input power: 300mW

Polarization dependent loss: 0.2 dB

Optical switches state setting time: 5 ms

VOA attenuation setting time in open loop: 20 ms

VOA attenuation setting time in closed loop: 500 ms (applicable to VOA in RX only)

VOA attenuation range: 0 - 15 dB

Dimensions

Height: 12.65 in. (332 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 8.66 in. (220.1 mm)

A.7  Multiplexer and Demultiplexer Cards

This section provides specifications for the 32MUX-O, 32DMX-O, and 4MD-xx.x cards.

A.7.1  32MUX-O Card Specifications

The 32MUX-O card optical specifications are listed in Table A-2.


Note For power specifications, see Table A-1.


Table A-2 32MUX-O Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Transmit (Tx) filter shape (-1 dB bandwidth)

All standard operating procedures (SOP) and within whole operating temperature range

In 1/32—Out beginning of life (BOL)

+/-180

+/-300

pm

In 1/32—Out end of life (EOL)

+/-160

+/-300

pm

Insertion loss

All SOP and within whole operating temperature range

In 1/32—Out BOL

4

8.0

dB

In 1/32—Out EOL

4

8.5

dB

VOA dynamic range

25

dB

Optical monitor tap-splitting ratio on monitor port

Optical monitor port with respect to output port in multiplexer only

19

21

dB

Maximum optical input power

300

mW


The 32MUX-O card has the following additional specifications:

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

A.7.2  32DMX-O Card Specifications

The 32DMX-O card optical specifications are listed in Table A-3.


Note For power specifications, see Table A-1.


Table A-3 32DMX-O Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Receive (Rx) filter shape (-1 dB bandwidth)

All SOP and within whole operating temperature range

In 1/32—Out BOL

+/-180

+/-300

pm

In 1/32—Out EOL

+/-160

+/-300

pm

Insertion loss

All SOP and within whole operating temperature range

In 1/32—Out BOL

4

8.0

dB

In 1/32—Out EOL

4

8.5

dB

VOA dynamic range

25

dB

Maximum optical input power

300

mW


The 32DMX-O card has the following additional specifications:

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

A.7.3  4MD-xx.x Card Specifications

The 4MD-xx.x card optical specifications are listed in Table A-4.


Note For power specifications, see Table A-1.


Table A-4 4MD-xx.x Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Trx filter shape (-0.5 dB bandwidth TrxBW2)

All SOP and within whole operating temperature range

COM Rx—xx.xx Tx

COM Rx—yy.yy Tx

COM Rx—zz.zz Tx

COM Rx—kk.kk Tx

+/-180

pm

xx.xx Rx—COM Tx

yy.yy Rx—COM Tx

zz.zz Rx—COM Tx

kk.kk Rx—COM Tx

Insertion loss demultiplexer section

All SOP and within whole operating temperature range

COM Rx—xx.xx Tx

1.9

dB

COM Rx—yy.yy Tx

2.4

dB

COM Rx—zz.zz Tx

2.8

dB

COM Rx—kk.kk Tx

3.3

dB

Insertion loss multiplexer section

All SOP and within whole operating temperature range (two connectors included)

xx.xx Rx—COM Tx

3.6

dB

yy.yy Rx—COM Tx

3.2

dB

zz.zz Rx—COM Tx

3.0

dB

kk.kk Rx—COM Tx

2.6

dB

VOA dynamic range

25

dB

Maximum optical input power

300

mW


The 4MD-xx.x card has the following additional specifications:

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

A.8  Reconfigurable Optical Add/Drop Cards

This section provides specifications for the 32DMX, 32DMX-L, 32WSS, 32WSS-L, 40-MUX-C, 40-DMX-C, 40-DMX-CE, 40-WSS-C, 40-WSS-CE, 40-WXC-C, 80-WXC-C, 40-SMR1-C, 40-SMR2-C, and MMU cards.

A.8.1  32DMX Card Specifications

The 32DMX card optical specifications are listed in Table A-5.


Note For power specifications, see Table A-1.


Table A-5 32DMX Optical Specifications 

Parameter
Note
Condition
Min
Typical
Max
Units

-1 dB bandwidth

All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation.

COM RX => TX 1, 32 (OUT)

+/-110

pm

-3 dB bandwidth

+/-200

pm

Insertion loss

All SOP, and within whole operating temperature range, connectors included.

COM RX => TX 1, 32

5.5

dB

VOA dynamic range

COM RX => TX 1, 32

25

dB

Maximum optical input power

300

mW


The 32DMX channel plan is shown in Table A-6. All 32DMX client interfaces must comply with this plan.

Table A-6 32DMX Channel Plan 

Channel Number
Band
Channel ID
Frequency (GHz)
Wavelength (nm)

1

1

30.3

195.9

1530.33

2

31.2

195.8

1531.12

3

31.9

195.7

1531.90

4

32.6

195.6

1532.68

5

2

34.2

195.4

1534.25

6

35.0

195.3

1535.04

7

35.8

195.2

1535.82

8

36.6

195.1

1536.61

9

3

38.1

194.9

1538.19

10

38.9

194.8

1538.98

11

39.7

194.7

1539.77

12

40.5

194.6

1540.56

13

4

42.1

194.4

1542.14

14

42.9

194.3

1542.94

15

43.7

194.2

1543.73

16

44.5

194.1

1544.53

17

5

46.1

193.9

1546.12

18

46.9

193.8

1546.92

19

47.7

193.7

1547.72

20

48.5

193.6

1548.51

21

6

50.1

193.4

1550.12

22

50.9

193.3

1550.92

23

51.7

193.2

1551.72

24

52.5

193.1

1552.52

25

7

54.1

192.9

1554.13

26

54.9

192.8

1554.94

27

55.7

192.7

1555.75

28

56.5

192.6

1556.55

29

8

58.1

192.4

1558.17

30

58.9

192.3

1558.98

31

59.7

192.2

1559.79

32

60.6

192.1

1560.61


The 32DMX card has the following additional specifications:

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

A.8.2  32DMX-L Card Specifications

The 32DMX-L card optical specifications are listed in Table A-5.


Note For power specifications, see Table A-1.


Table A-7 32DMX -L Optical Specifications 

Parameter
Note
Condition
Min
Typical
Max
Units

-1 dB bandwidth

All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation.

COM RX => TX 1, 32 (OUT)

+/-100

pm

-3 dB bandwidth

+/-199

pm

Insertion loss

All SOP, and within whole operating temperature range, connectors included.

COM RX => TX 1, 32

5.8

dB

VOA dynamic range

COM RX => TX 1, 32

25

dB

Maximum optical input power

300

mW


The 32DMX-L channel plan is shown in Table A-8. All 32DMX-L client interfaces must comply with this plan.

Table A-8 32DMX-L Channel Plan  

Band ID
Channel Label
Frequency (THz)
Wavelength (nm)

B77.8

77.8

190

1577.86

78.6

189.9

1578.69

79.5

189.8

1579.52

80.3

189.7

1580.35

B81.1

81.1

189.6

1581.18

82.0

189.5

1582.02

82.8

189.4

1582.85

83.6

189.3

1583.69

B84.5

84.5

189.2

1584.53

85.3

189.1

1585.36

86.2

189

1586.20

87.0

188.9

1587.04

B87.8

87.8

188.8

1587.88

88.7

188.7

1588.73

89.5

188.6

1589.57

90.4

188.5

1590.41

B91.2

91.2

188.4

1591.26

92.1

188.3

1592.10

92.9

188.2

1592.95

93.7

188.1

1593.79

B94.6

94.6

188

1594.64

95.4

187.9

1595.49

96.3

187.8

1596.34

97.1

187.7

1597.19

B98.0

98.0

187.6

1598.04

98.8

187.5

1598.89

99.7

187.4

1599.75

00.6

187.3

1600.60

B01.4

01.4

187.2

1601.46

02.3

187.1

1602.31

03.1

187

1603.17

04.0

186.9

1604.03


The 32DMX-L card has the following additional specifications:

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

A.8.3  32WSS Card Specifications

The 32WSS card optical specifications are listed in Table A-9.


Note For power specifications, see Table A-1.


Table A-9 32WSS Optical Specifications 

Parameter
Note
Condition
Min
Typical
Max
Units

-0.25 dB bandwidth

All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation.

EXP RX => COM TX

+/-/95

pm

-0.5 dB bandwidth

+/-115

pm

-1.0 dB bandwidth

+/-135

pm

-0.25 dB bandwidth

Add 1, 32 => COM TX

+/-115

pm

-0.5 dB bandwidth

+/-135

pm

-1.0 dB bandwidth

+/-160

pm

Insertion loss

All SOP, any optical switch state, and within whole operating temperature range, connectors included.

EXP RX => COM TX

11.3

dB

COM RX => EXP TX

1.5

dB

Add 1, 32 => COM TX

7.6

dB

COM RX => DROP TX

6

8.5

dB

VOA dynamic range

EXP RX => COM TX

20

dB

Add 1, 32 => COM TX

25

dB

Maximum optical input power

300

mW


The 32WSS channel plan is shown in Table A-10. All 32WSS client interfaces must comply with this plan.

Table A-10 32WSS Channel Plan 

Channel Number
Band
Channel ID
Frequency (GHz)
Wavelength (nm)

1

1

30.3

195.9

1530.33

2

31.2

195.8

1531.12

3

31.9

195.7

1531.90

4

32.6

195.6

1532.68

5

2

34.2

195.4

1534.25

6

35.0

195.3

1535.04

7

35.8

195.2

1535.82

8

36.6

195.1

1536.61

9

3

38.1

194.9

1538.19

10

38.9

194.8

1538.98

11

39.7

194.7

1539.77

12

40.5

194.6

1540.56

13

4

42.1

194.4

1542.14

14

42.9

194.3

1542.94

15

43.7

194.2

1543.73

16

44.5

194.1

1544.53

17

5

46.1

193.9

1546.12

18

46.9

193.8

1546.92

19

47.7

193.7

1547.72

20

48.5

193.6

1548.51

21

6

50.1

193.4

1550.12

22

50.9

193.3

1550.92

23

51.7

193.2

1551.72

24

52.5

193.1

1552.52

25

7

54.1

192.9

1554.13

26

54.9

192.8

1554.94

27

55.7

192.7

1555.75

28

56.5

192.6

1556.55

29

8

58.1

192.4

1558.17

30

58.9

192.3

1558.98

31

59.7

192.2

1559.79

32

60.6

192.1

1560.61


The 32WSS card has the following additional specifications:

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

A.8.4  32WSS-L Card Specifications

The 32WSS-L card optical specifications are listed in Table A-11.


Note For power specifications, see Table A-1.


Table A-11 32WSS-L Optical Specifications 

Parameter
Note
Condition
Min
Typical
Max
Units

-0.1 dB bandwidth

All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation.

EXP RX => COM TX

+/-/57

pm

-0.25 dB bandwidth

+/-/61

+/-/89

-0.5 dB bandwidth

+/-91

+/-/116

-1.0 dB bandwidth

+/-135

+/-/149

-0.1 dB bandwidth

Add 1, 32 => COM TX

+/-32

+/-/69

-0.25 dB bandwidth

+/-98

+/-/129

-0.5 dB bandwidth

+/-135

+/-/161

-1.0 dB bandwidth

+/-160

+/-/201

Insertion loss

All SOP, any optical switch state, and within whole operating temperature range, connectors included.

EXP RX => COM TX

9.7

11.3

dB

COM RX => EXP TX

1.4

1.6

dB

Add 1, 32 => COM TX

6.2

8.0

dB

COM RX => DROP TX

6.0

8.0

8.5

dB

VOA dynamic range

EXP RX => COM TX

20

25

dB

Add 1, 32 => COM TX

25

25

dB

Maximum optical input power

300

mW


The 32WSS-L channel plan is shown in Table A-12. All 32WSS-L client interfaces must comply with this plan.

Table A-12 32WSS-L Channel Plan  

Band ID
Channel Label
Frequency (THz)
Wavelength (nm)

B77.8

77.8

190

1577.86

78.6

189.9

1578.69

79.5

189.8

1579.52

80.3

189.7

1580.35

B81.1

81.1

189.6

1581.18

82.0

189.5

1582.02

82.8

189.4

1582.85

83.6

189.3

1583.69

B84.5

84.5

189.2

1584.53

85.3

189.1

1585.36

86.2

189

1586.20

87.0

188.9

1587.04

B87.8

87.8

188.8

1587.88

88.7

188.7

1588.73

89.5

188.6

1589.57

90.4

188.5

1590.41

B91.2

91.2

188.4

1591.26

92.1

188.3

1592.10

92.9

188.2

1592.95

93.7

188.1

1593.79

B94.6

94.6

188

1594.64

95.4

187.9

1595.49

96.3

187.8

1596.34

97.1

187.7

1597.19

B98.0

98.0

187.6

1598.04

98.8

187.5

1598.89

99.7

187.4

1599.75

00.6

187.3

1600.60

B01.4

01.4

187.2

1601.46

02.3

187.1

1602.31

03.1

187

1603.17

04.0

186.9

1604.03


The 32WSS-L card has the following additional specifications:

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

A.8.5  40-MUX-C Card Specifications

The 40-MUX-C card optical specifications are listed in Table A-13.


Note For power specifications, see Table A-1.


Table A-13 40-MUX-C Card Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Transmit (Tx) filter shape

All standard operating procedures (SOP) and within whole operating temperature range

-1 dB bandwidth,
RX 1, 40 => COM TX

+/-100

pm

-3 dB bandwidth,
RX 1, 40 => COM TX

+/-199

pm

Insertion loss

All SOP and within whole operating temperature range

RX 1, 40 => COM TX

 

5.8

dB

VOA dynamic range

RX 1, 40 => COM TX

25

dB

Maximum optical input power

300

mW


The 40-MUX-C card has the following additional specifications:

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

A.8.6  40-DMX-C Card Specifications

The 40-DMX-C card optical specifications are listed in Table A-14.


Note For power specifications, see Table A-1.


Table A-14 40-DMX-C Card Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Receive (Rx) filter shape

All SOP and within whole operating temperature range

-1 dB bandwidth,
COM RX => TX 1, 40 (OUT)

+/-100

pm

-3 dB bandwidth,
COM RX => TX 1, 40 (OUT)

+/-199

pm

Insertion loss

All SOP and within whole operating temperature range

COM RX => TX 1, 40

5.8

dB

VOA dynamic range

COM RX => TX 1, 40

25

dB

Maximum optical input power

300

mW


The 40-DMX-C card has the following additional specifications:

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

A.8.7  40-DMX-CE Card Specifications

The 40-DMX-CE card optical specifications are listed in Table A-15.


Note For power specifications, see Table A-1.


Table A-15 40-DMX-CE Card Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Receive (Rx) filter shape

All SOP and within whole operating temperature range

-1 dB bandwidth,
COM RX => TX 1, 40 (OUT)

+/-100

pm

-3 dB bandwidth,
COM RX => TX 1, 40 (OUT)

+/-199

pm

Insertion loss

All SOP and within whole operating temperature range

COM RX => TX 1, 40

5.8

dB

VOA dynamic range

COM RX => TX 1, 40

25

dB

Maximum optical input power

300

mW


The 40-DMX-CE card has the following additional specifications:

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

A.8.8  40-WSS-C Card Specifications

The 40-WSS-C card optical specifications are listed in Table A-16.


Note For power specifications, see Table A-1.


Table A-16 40-WSS-C Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Channel grid: -0.1 dB

All SOP and within whole operating temperature range

EXP_RX to COM_ TX

pm

Channel grid: -0.25 dB

+/- 61

pm

Channel grid: -0.5 dB

+/- 91

pm

Channel grid: -1.0 dB

+/- 135

pm

Channel grid: -0.1 dB

All SOP and within whole operating temperature range

EXP_RX to COM_ TX

+/- 32

pm

Channel grid: -0.25 dB

+/- 98

pm

Channel grid: -0.5 dB

+/- 135

pm

Channel grid: -1.0 dB

+/- 160

pm

Insertion loss

All SOP and within whole operating temperature range

EXP_RX to COM_ TX

7.5

dB

EXP_RX to COM_ TX

2.3

dB

EXP_RX to COM_ TX

6.0

dB

EXP_RX to COM_ TX

6.8

dB

VOA dynamic range

EXP_RX to COM_ TX

20

dB

EXP_RX to COM_ TX

25

dB

Maximum optical input power

300

mW


The 40-WSS-C card channel grid is listed in Table A-17.

Table A-17 40-WSS-C Channel Grid 

Band ID
Channel Label
Frequency (THz)
Wavelength (nm)

B30.3

30.3

195.9

1530.33

31.1

195.8

1531.12

31.9

195.7

1531.90

32.6

195.6

1532.68

33.4

195.5

1533.47

B34.2

34.2

195.4

1534.25

35.0

195.3

1535.04

35.8

195.2

1535.82

36.6

195.1

1536.61

37.4

195.0

1537.4

B38.1

38.1

194.9

1538.19

38.9

194.8

1538.98

39.7

194.7

1539.77

40.5

194.6

1540.56

41.3

194.5

1541.35

B42.1

42.1

194.4

1542.14

42.9

194.3

1542.94

43.7

194.2

1543.73

44.5

194.1

1544.53

45.3

194.0

1545.32

B46.1

46.1

193.9

1546.12

46.9

193.8

1546.92

47.7

193.7

1547.72

48.5

193.6

1548.51

49.3

193.5

1549.32

B50.1

50.1

193.4

1550.12

50.9

193.3

1550.92

51.7

193.2

1551.72

52.5

193.1

1552.52

53.3

193.0

1553.33

54.1

54.1

192.9

1544.13

54.9

192.8

1544.94

55.7

192.7

1555.75

56.5

192.6

1556.55

57.3

192.5

1557.36

B58.1

58.1

192.4

1558.17

58.9

192.3

1558.98

59.7

192.2

1559.79

60.6

192.1

1560.61

61.4

192.0

1561.42


The 40-WSS-C card has the following additional specifications:

Dimensions

Height: 8.66 in. (220 mm)

Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)

Depth: 1.42 in. (36 mm)

A.8.9  40-WSS-CE Card Specifications

The 40-WSS-CE card optical specifications are listed in Table A-18.


Note For power specifications, see Table A-1.


Table A-18 40-WSS-C Card Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Channel grid: -0.1 dB

All SOP and within whole operating temperature range

EXP RX greater than or equal to COM TX

pm

Channel grid: -0.25 dB

+/- 61

pm

Channel grid: -0.5 dB

+/- 91

pm

Channel grid: -1.0 dB

+/- 135

pm

Channel grid: -0.1 dB

All SOP and within whole operating temperature range

Add 1, 40 greater than or equal to COM TX

+/- 32

pm

Channel grid: -0.25 dB

+/- 98

pm

Channel grid: -0.5 dB

+/- 135

pm

Channel grid: -1.0 dB

+/- 160

pm

Insertion loss

All SOP and within whole operating temperature range

EXP RX greater than or equal to COM TX

7.5

dB

COM RX greater than or equal to EXP TX

2.3

dB

Add 1, 40 greater than or equal to COM TX

6.0

dB

COM RX greater than or equal to DROP TX

6.8

dB

VOA dynamic range

EXP RX greater than COM TX

20

dB

Add 1, 40 greater than or equal to COM TX

25

dB

Maximum optical input power

300

mW


The 40-WSS-CE card channel grid is listed in Table A-19.

Table A-19 40-WSS-C Card Channel Grid 

Band ID
Channel Label
Frequency (THz)
Wavelength (nm)

B30.7

30.7

195.85

1530.72

31.5

195.75

1531.51

32.3

195.65

1532.29

33.1

195.55

1533.07

33.9

195.45

1533.86

B34.6

34.6

195.35

1534.64

35.4

195.25

1535.43

36.2

195.15

1536.22

37.0

195.05

1537.00

37.8

194.95

1537.79

B38.6

38.6

194.85

1538.58

39.4

194.75

1539.37

40.1

194.65

1540.16

40.9

194.55

1540.95

41.8

194.45

1541.75

B42.5

42.5

194.35

1542.54

43.3

194.25

1543.33

44.1

194.15

1544.13

44.9

194.05

1544.92

45.7

193.95

1545.72

B46.5

46.5

193.85

1546.52

47.3

193.75

1547.32

48.1

193.65

1548.11

48.9

193.55

1548.91

49.7

193.45

1549.72

B50.5

50.5

193.35

1550.52

51.3

193.25

1551.32

52.1

193.15

1552.12

52.9

193.05

1552.93

53.7

192.95

1553.73

B54.4

54.4

192.85

1554.54

55.3

192.75

1555.34

56.1

192.65

1556.15

56.9

192.55

1556.96

57.8

192.45

1557.77

B58.6

58.6

192.35

1558.58

59.4

192.25

1559.39

60.2

192.15

1560.20

61.0

192.05

1561.01

61.8

191.95

1561.83


The 40-WSS-CE card has the following additional specifications:

Dimensions

Height: 8.66 in. (220 mm)

Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)

Depth: 1.42 in. (36 mm)

A.8.10  40-WXC-C Card Specifications

The 40-WXC-C card optical specifications are listed in Table A-20.


Note For power specifications, see Table A-1.


Table A-20 40-WXC-C Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Channel bandwidth: -0.25 dB

All SOP and within whole operating temperature range

All paths

GHz

Channel bandwidth: -0.5 dB

+/- 20.5

GHz

Channel bandwidth: -1.5 dB

GHz

Channel bandwidth: -03.0 dB

+/- 37.5

GHz

Insertion loss

All SOP and within whole operating temperature range

All paths

8.5

dB

VOA dynamic range

All paths

20

dB

Maximum optical input power

300

mW


The 40-WXC-C card has the following additional specifications:

Dimensions

Height: 12.65 in. (321.3 mm) for a standard DWDM unit

Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm) for a standard DWDM unit

A.8.11  80-WXC-C Card Specifications

The 80-WXC-C card optical specifications are listed in Table A-21.


Note For power specifications, see Table A-1.


Table A-21 80-WXC-C Card Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Channel grid

50 GHz spaced standard ITU Grid and Channel Zero at 1529.55nm (196 THz)

 

191.95

196.00

THz

Operating Wavelength Bandwidth

All SOP; and within whole operating temperature range; connectors included and for minimum operating attenuation

All paths

+/- 12.5

GHz

Channel bandwidth: -0.25 dB

Vendor provided 1

GHz

Channel bandwidth: -0.5 dB

+/- 12.5

Channel bandwidth: -1.5 dB

+/- 17

Channel bandwidth: -03.0 dB

Vendor provided 1

Insertion loss

All SOP; any optical switch state and within whole operating temperature range; connectors included and for minimum attenuation

All paths

2.0

7.0

dB

VOA dynamic range

All paths

25

dB

Maximum optical input power

All ports

500

mW

1 Use the value provided by the third-party vendor.


The 80-WXC-C card has the following additional specifications:

Dimensions

Height: 13.11 in. (333 mm) for a standard DWDM unit

Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)

Depth:9.88 in. (251 mm) for a standard DWDM unit

A.8.12  40-SMR1-C Card Specifications

The 40-SMR1-C card optical specifications are listed in Table A-22.


Note For power specifications, see Table A-1.


Table A-22 40-SMR1-C Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Channel bandwidth: -0.25 dB

All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation

All WXC paths (ADD-RX to LINE-TX and EXP-RX to LINE-TX)

pm

Channel bandwidth: -0.5 dB

+/- 160

pm

Channel bandwidth: -1.5 dB

pm

Channel bandwidth: -3.0 dB

+/- 240

pm

Insertion loss

All SOP, any optical switch state, and within whole operating temperature range, connectors included

All WXC paths (ADD-RX to LINE-TX and EXP-RX to LINE-TX)

2.0

8.1

dB

All SOP, within whole operating temperature range, connectors included

DROP-TX with respect to EXP-TX

5.3

dB

VOA dynamic range

All WXC paths (ADD-RX to LINE-TX and EXP-RX to LINE-TX)

20

dB

DROP-TX

25

dB

Maximum optical input power

Total power sum of all ports

500

mW


The EDFA1 amplifier within the 40-SMR1-C card has the following specifications:

Optical characteristics (specified from LINE-RX to EXP-TX)

Total operating wavelength range: 1530 to 1561.5 nm

Gain ripple (peak to valley): 1.2 dB

Mid-access loss (MAL) range (for dispersion compensation unit [DCU]): 0 to 9 dB

Gain range: 7 to 38 dB

Minimum gain (standard range): 7.0 dB

Maximum gain (standard range with programmable gain tilt): 21 dB

Maximum gain (extended range with uncontrolled gain tilt): 38 dB

Gain and power regulation over/undershoot: 0.5 dB

Maximum output power (with full channel load): 17 dBm

Minimum output power (with one channel): -5 dBm

Input power (pin) range at full channel load: -21 to 12 dBm

Input power (pin) range at single channel load: -43 to -10 dBm

Noise figure at G = 21 dB = 7.5 dB

The OSC filter within the 40-SMR1-C card has the following specifications:

OSC filter drop (OSC) insertion loss maximum: 1.8 dB

OSC filter add (OSC) insertion loss maximum: 1.3 dB

The 40-SMR1-C card has the following additional specifications:

Dimensions

Height: 13.11 in. (333 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.88 in. (251 mm)

A.8.13  40-SMR2-C Card Specifications

The 40-SMR2-C card optical specifications are listed in Table A-23.


Note For power specifications, see Table A-1.


Table A-23 40-SMR2-C Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Channel bandwidth: -0.25 dB

All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation

All WXC paths (ADD-RX to WXC output, EXP1-RX to WXC output, EXP2-RX to WXC output, and EXP3-RX to WXC output)

pm

Channel bandwidth: -0.5 dB

+/- 160

pm

Channel bandwidth: -1.5 dB

pm

Channel bandwidth: -3.0 dB

+/- 240

pm

Insertion loss

All SOP, any optical switch state, and within whole operating temperature range, connectors included

All WXC paths (ADD-RX to WXC output, EXP1-RX to WXC output, EXP2-RX to WXC output, and EXP3-RX to WXC output)

2.0

7

dB

All SOP, within whole operating temperature range, connectors included

DROP-TX with respect to EXP-TX

5.3

dB

VOA dynamic range

All WXC paths (ADD-RX to WXC output, EXP1-RX to WXC output, EXP2-RX to WXC output, and EXP3-RX to WXC output)

20

dB

DROP-TX

25

dB

Maximum optical input power

Total power sum of all ports

500

mW


The EDFA1 amplifier within the 40-SMR2-C card has the following specifications:

Optical characteristics (specified from LINE-RX to EXP-TX)

Total operating wavelength range: 1530 to 1561.5 nm

Gain ripple (peak to valley): 1.2 dB

Mid-access loss (MAL) range (for dispersion compensation unit [DCU]): 0 to 9 dB

Gain range: 7 to 38 dBm in constant gain mode

Minimum gain (standard range): 7.0 dBm

Maximum gain (standard range with programmable gain tilt): 21 dBm

Maximum gain (extended range with uncontrolled gain tilt): 38 dBm

Gain and power regulation over/undershoot: 0.5 dB

Maximum output power (with full channel load): 17 dBm

Minimum output power (with one channel): -5 dBm

Input power (pin) range at full channel load: -21 to 12 dBm

Input power (pin) range at single channel load: -43 to -10 dBm

Noise figure at G= 21 dB = 7.5 dB

The EDFA2 amplifier within the 40-SMR2-C card has the following specifications:

Optical characteristics (specified from WXC output to LINE-TX)

Total operating wavelength range 1530.0 to 1561.5 nm

Gain ripple (peak to valley): 1.2 dB

Gain range: 13 to 26 dB

Optimal gain (gain tilt = 0): 17 dB

Gain and power regulation over/undershoot: 0.5 dB

Minimum output power (with one channel): -5 dBm

Input power range (full channel load): -9 to 4 dBm

Input power range (single channel load): -31 to -18 dBm

Noise figure at G=17dB = 6 dB maximum

The OSC filter within the 40-SMR2-C card has the following specifications:

OSC filter drop (OSC) insertion loss maximum: 1.8 dB

OSC filter add (OSC) insertion loss maximum: 1.3 dB

The 40-SMR2-C card has the following additional specifications:

Dimensions

Height: 13.11 in. (333 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.88 in. (251 mm)

A.8.14  MMU Card Specifications

The MMU card optical specifications are listed in Table A-24.


Note For power specifications, see Table A-1.


Table A-24 MMU Optical Specifications 

Parameter
Note
Condition
Min
Typical
Max
Units

Operating bandwidth

All SOP, any optical switch state, and within whole operating temperature range, connectors included.

All paths

1500

1605

nm

Insertion loss

All SOP, any optical switch state, and within whole operating temperature range, connectors included.

EXP RX => COM TX

7.0

dB

EXP A RX => COM TX

2.3

dB

COM RX => EXP TX

0.8

dB

COM RX => EXP A TX

14.8

dB

Wavelength dependent losses

All SOP, any optical switch state, and within whole operating temperature range, connectors included.

C-band only

0.3

dB

L-band only

0.3

dB

C and L bands

0.5

dB

Polarization dependent loss (PDL)

C-band only

0.2

dB

L-band only

0.2

dB

C and L bands

0.3

dB

Chromatic dispersion

 

All paths

-20

+20

ps/nm

Polarization mode dispersion (PMD)

All paths

0.1

ps

Optical power reading resolution

All photodiodes (both real and virtual)

0.1

dB

Optical power reading precision

-0.1

0.1

dB

Directivity

All SOP, any optical switch state, and within whole operating temperature range, connectors included.

EXP RX => EXP A RX

40

dB

EXP RX => EXP B RX

40

dB

EXP A RX => EXP B RX

40

dB

Return loss

40

dB

Maximum optical input power

Maximum handling power

500

mW


The MMU card has the following additional specifications:

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 8.66 in. (220.1 mm)

A.9  Optical Add/Drop Cards

This section provides specifications for the AD-IC-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.

A.9.1  AD-1C-xx.x Card Specifications

Table A-25 lists the AD-1C-xx.x optical specifications.

Table A-25 AD-1C-xx.x Card Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Trx filter shape
(-0.5 dB bandwidth)
TrxBW2

All SOP and within whole operating temperature range

COM Rx—xx.xx Tx
xx.xx Rx—COM Tx

+/-180

pm

Rfx filter shape
(-0.5 dB bandwidth)
RfxBW2

All SOP and within whole operating temperature range

COM Rx—Exp Tx
Exp Rx—COM Tx

+/-180

pm

Insertion loss
(drop section)

All SOP and within whole operating temperature range (two connectors included)

COM Rx—xx.xx Tx

2.0

dB

Insertion loss
(express section)

VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included)

COM Rx—Exp Tx
Exp Rx—COM Tx

2.4 or 1.2

dB

Insertion loss
(add section)

VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included)

xx.xx Rx—COM Tx

2.6

dB

VOA dynamic range

30

dB

Maximum optical input power

300

mW


The AD-1C-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 8-3 through Table 8-7 for this information.

The AD-1C-xx.x card has the following additional specifications:

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.0 in. (228.6 mm)

A.9.2  AD-2C-xx.x Card Specifications

Table A-26 lists the AD-2C-xx.x optical specifications.

Table A-26 AD-2C-xx.x Card Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Trx filter shape
(-0.5 dB bandwidth)
TrxBW2

All SOP and within whole operating temperature range

COM Rx—xx.xx Tx
COM Rx—yy.yy Tx

+/-180

pm

xx.xx Rx—COM Tx
yy.yy Rx—COM Tx

+/-180

Rfx filter shape
(-0.5 dB bandwidth)
RfxBW2

All SOP and within whole operating temperature range

COM Rx—Exp Tx
Exp Rx—COM Tx

+/-180

pm

Insertion loss
(drop section)

All SOP and within whole operating temperature range (two connectors included)

COM Rx—xx.xx Tx

2.0

dB

COM Rx—yy.yy Tx

2.4

dB

Insertion loss
(express section)

VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included)

COM Rx—Exp Tx

2.7

dB

Exp Rx—COM Tx

1.6

dB

Insertion loss
(add section)

VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included)

xx.xx Rx—COM Tx

3.1

dB

yy.yy Rx—COM Tx

2.7

dB

VOA dynamic range

30

dB

Maximum optical input power

300

mW


The AD-2C-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 8-3 through Table 8-7 for this information.

The AD-2C-xx.x has the following additional specifications:

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.0 in. (228.6 mm)

A.9.3  AD-4C-xx.x Card Specifications

Table A-27 lists the AD-4C-xx.x optical specifications.

Table A-27 AD-4C-xx.x Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Channel grid

See Table A-28. The channel plan for the AD-4C-xx.x card is identical to the channel plan for the AD-1B-xx.x card.

Trx filter shape
(-0.5 dB bandwidth)
TrxBW2

All SOP and within whole operating temperature range

COM Rx—xx.xx Tx
COM Rxyy.yy Tx
COM Rx—zz.zz Tx
COM Rx—kk.kk Tx
xx.xx Rx—COM Tx
yy.yy Rx—COM Tx

+/-180

pm

Rfx filter shape
(-1 dB bandwidth)
RfxBW2

All SOP and within whole operating temperature range

COM Rx—Exp Tx
Exp Rx—COM Tx

pm

Insertion loss
(drop section)

All SOP and within whole operating temperature range (two connectors included)

COM Rx—xx.xx Tx

5.5

dB

COM Rx—yy.yy Tx

5.0

dB

COM Rx—zz.zz Tx

4.5

dB

COM Rx—kk.kk Tx

4.1

dB

Insertion loss
(express section)

VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included)

COM Rx—Exp Tx

2.7

dB

Exp Rx—COM Tx

1.2

dB

Insertion loss
(add section)

VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included)

xx.xx Rx—COM Tx

3.9

dB

yy.yy Rx—COM Tx

4.3

dB

zz.zz Rx—COM Tx

4.5

dB

kk.kk Rx—COM Tx

4.9

dB

VOA dynamic range

30

dB

Maximum optical input power

300

mW


The AD-4C-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 8-3 through Table 8-7 for this information.

The AD-4C-xx.x has the following additional specifications:

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.0 in. (228.6 mm)

A.9.4  AD-1B-xx.x Card Specifications

Table A-28 lists the unit names, band IDs, channel IDs, frequencies, and wavelengths assigned to the eight versions of the AD-1B-xx.x card.

Table A-28 AD-1B-xx.x Channel Allocation Plan by Band 

Unit Name
Band ID
Channel ID
Frequency (GHz)
Wavelength (nm)

AD-1B-30.3

B30.3

30.3

195.9

1530.33

30.7

195.85

1530.72

31.1

195.8

1531.12

31.5

195.75

1531.51

31.9

195.7

1531.90

32.2

195.65

1532.29

32.6

195.6

1532.68

33.3

195.55

1533.07

AD-1B-34.2

B34.2

34.2

195.4

1534.25

34.6

195.35

1534.64

35.0

195.3

1535.04

35.4

195.25

1535.43

35.8

195.2

1535.82

36.2

195.15

1536.22

36.6

195.1

1536.61

37.0

195.05

1537.00

AD-1B-38.1

B38.1

38.1

194.9

1538.19

38.5

194.85

1538.58

38.9

194.8

1538.98

39.3

194.75

1539.37

39.7

194.7

1539.77

40.1

194.65

1540.16

40.5

194.6

1540.56

40.9

194.55

1540.95

AD-1B-42.2

B42.1

42.1

194.4

1542.14

42.5

194.35

1542.54

42.9

194.3

1542.94

43.3

194.25

1543.33

43.7

194.2

1543.73

44.1

194.15

1544.13

44.5

194.1

1544.53

44.9

194.05

1544.92

AD-1B-46.1

B46.1

46.1

193.9

1546.12

46.5

193.85

1546.52

46.9

193.8

1546.92

47.3

193.75

1547.32

47.7

193.7

1547.72

48.1

193.65

1548.11

48.5

193.6

1548.51

48.9

193.55

1548.91

AD-1B-50.1

B50.1

50.1

193.4

1550.12

50.5

193.35

1550.52

50.9

193.3

1550.92

51.3

193.25

1551.32

51.7

193.2

1551.72

52.1

193.15

1552.12

52.5

193.1

1552.52

52.9

193.05

1552.93

AD-1B-54.1

B54.1

54.1

192.9

1554.13

54.5

192.85

1554.54

54.9

192.8

1554.94

55.3

192.75

1555.34

55.7

192.7

1555.75

56.1

192.65

1556.15

56.5

192.6

1556.96

56.9

192.55

1556.96

AD-1B-58.1

B58.1

58.1

192.4

1558.17

58.5

192.35

1558.58

58.9

192.3

1558.98

59.3

192.25

1559.39

59.7

192.2

1559.79

60.2

192.15

1560.20

60.6

192.1

1560.61

61.0

192.05

1561.01


Table A-29 lists AD-1B-xx.x optical specifications.

Table A-29 AD-1B-xx.x Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

-1 dB bandwidth

All SOP and within whole operating environmental range

COM Rx—Band Tx
Band Rx—COM Tx

3.6

nm

-1 dB bandwidth

All SOP and within whole operating temperature range

COM Rx—Exp Tx
Exp Rx—COM Tx

See Table A-30.

nm

Insertion loss
(drop section)

All SOP and within whole operating environmental range; two connectors included, VOA set at minimum attenuation

COM Rx—Band Tx

3.0

dB

Insertion loss
(express section)

All SOP and within whole operating environmental range; two connectors included

Exp Rx—COM Tx

1.6

dB

All SOP and within whole operating environmental range; two connectors included, VOA set at its minimum attenuation

COM Rx—Exp Tx

2.2

dB

Insertion loss
(add section)

All SOP and within whole operating environmental range; two connectors included

Band Rx—COM Tx

2.2

dB

VOA dynamic range

30

dB

Maximum optical input power

300

mW


Table A-30 lists the range of wavelengths for the receive (express) band.

Table A-30 AD-1B-xx.x Transmit and Receive Dropped Band Wavelength Ranges 

Tx (Dropped) Band
Rx (Express) Band
Left Side (nm)
Right Side (nm)

B30.3

Wavelengths 1533.825 or higher

B34.2

Wavelengths 1533.395 or lower

Wavelengths 1537.765 or higher

B38.1

Wavelengths 1537.325 or lower

Wavelengths 1541.715 or higher

42.1

Wavelengths 1541.275 or lower

Wavelengths 1545.695 or higher

46.1

Wavelengths 1545.245 or lower

Wavelengths 1549.695 or higher

50.1

Wavelengths 1549.235 or lower

Wavelengths 1553.705 or higher

54.1

Wavelengths 1553.255 or lower

Wavelengths 1557.745 or higher

58.1

Wavelengths 1557.285 or lower


The AD-1B-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 8-3 through Table 8-7 for this information.

The AD-1B-xx.x card has the following additional specifications:

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.0 in. (228.6 mm)

A.9.5  AD-4B-xx.x Card Specifications

Table A-31 lists the unit names, band IDs, channel IDs, frequencies, and wavelengths assigned to the two versions of the card.

Table A-31 AD-4B-xx.x Channel Allocation Plan by Band 

Unit Name
Band ID
Channel ID
Frequency (GHz)
Wavelength (nm)

AD-4B-30.3

B30.3

30.3

195.9

1530.33

30.7

195.85

1530.72

31.1

195.8

1531.12

31.5

195.75

1531.51

31.9

195.7

1531.90

32.2

195.65

1532.29

32.6

195.6

1532.68

33.3

195.55

1533.07

B34.2

34.2

195.4

1534.25

34.6

195.35

1534.64

35.0

195.3

1535.04

35.4

195.25

1535.43

35.8

195.2

1535.82

36.2

195.15

1536.22

36.6

195.1

1536.61

37.0

195.05

1537.00

B38.1

38.1

194.9

1538.19

38.5

194.85

1538.58

38.9

194.8

1538.98

39.3

194.75

1539.37

39.7

194.7

1539.77

40.1

194.65

1540.16

40.5

194.6

1540.56

40.9

194.55

1540.95

B42.1

42.1

194.4

1542.14

42.5

194.35

1542.54

42.9

194.3

1542.94

43.3

194.25

1543.33

43.7

194.2

1543.73

44.1

194.15

1544.13

44.5

194.1

1544.53

44.9

194.05

1544.92

AD-4B-46.1

B46.1

46.1

193.9

1546.12

46.5

193.85

1546.52

46.9

193.8

1546.92

47.3

193.75

1547.32

47.7

193.7

1547.72

48.1

193.65

1548.11

48.5

193.6

1548.51

48.9

193.55

1548.91

B50.1

50.1

193.4

1550.12

50.5

193.35

1550.52

50.9

193.3

1550.92

51.3

193.25

1551.32

51.7

193.2

1551.72

52.1

193.15

1552.12

52.5

193.1

1552.52

52.9

193.05

1552.93

B54.1

54.1

192.9

1554.13

54.5

192.85

1554.54

54.9

192.8

1554.94

55.3

192.75

1555.34

55.7

192.7

1555.75

56.1

192.65

1556.15

56.5

192.6

1556.96

56.9

192.55

1556.96

B58.1

58.1

192.4

1558.17

58.5

192.35

1558.58

58.9

192.3

1558.98

59.3

192.25

1559.39

59.7

192.2

1559.79

60.2

192.15

1560.20

60.6

192.1

1560.61

61.0

192.05

1561.01


Table A-32 lists AD-4B-xx.x optical specifications.

Table A-32 AD-4B-xx.x Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

-1 dB bandwidth

All SOP and within whole operating environmental range

COM Rx—Band Tx
Band Rx—COM Tx

3.6

nm

-1 dB bandwidth

All SOP and within whole operating temperature range

COM Rx—Exp Tx
Exp Rx—COM Tx

Refer to Table A-33.

nm

Insertion loss
(drop section)

All SOP and within whole operating environmental range; two connectors included, VOA set at minimum attenuation

COM Rx—Band Tx
30.3/46.1

2.9

dB

COM Rx—Band Tx
34.2/50.1

3.3

dB

COM Rx—Band Tx
38.1/54.1

3.8

dB

COM Rx—Band Tx
42.1/58.1

4.5

dB

Insertion loss
(express section)

All SOP and within whole operating environmental range; two connectors included

Exp Rx—COM Tx

4.9

dB

All SOP and within whole operating environmental range; two connectors included, VOA set at its minimum attenuation

COM Rx—Exp Tx

3

dB

Insertion loss
(add section)

All SOP and within whole operating environmental range; two connectors included

Band Rx 30.3/46.1—COM Tx

3.5

dB

Band Rx 34.2/50.1—COM Tx

2.8

dB

Band Rx 38.1/54.1—COM Tx

2.3

dB

Band Rx 42.1/58.1—COM Tx

1.8

dB

VOA dynamic range

30

dB

Maximum optical input power

300

mW


Table A-33 lists the range of wavelengths for the receive (express) band.

Table A-33 AD-4B-xx.x Transmit and Receive Dropped Band Wavelength Ranges 

Tx (Dropped) Band
Rx (Express) Band
Left Side (nm)
Right Side (nm)

B30.3

Wavelengths 1533.825 or higher

B34.2

Wavelengths 1533.395 or lower

Wavelengths 1537.765 or higher

B38.1

Wavelengths 1537.325 or lower

Wavelengths 1541.715 or higher

B42.1

Wavelengths 1541.275 or lower

Wavelengths 1545.695 or higher

B46.1

Wavelengths 1545.245 or lower

Wavelengths 1549.695 or higher

B50.1

Wavelengths 1549.235 or lower

Wavelengths 1553.705 or higher

B54.1

Wavelengths 1553.255 or lower

Wavelengths 1557.745 or higher

B58.1

Wavelengths 1557.285 or lower


The AD-4B-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 8-3 through Table 8-7 for this information.

The AD-4B-xx.x has the following additional specifications:

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.0 in. (228.6 mm)

A.10  Transponder and Muxponder Card Specifications

This section provides specifications for the TXP_MR_10G, MXP_2.5G_10G, TXP_MR_2.5G, TXPP_MR_2.5G, MXP_MR_2.5G, MXPP_MR_2.5G, MXP_2.5G_10E, MXP_2.5G_10E_C, MXP_2.5G_10EX_C, MXP_2.5G_10E, TXP_MR_10E, TXP_MR_10E_C, TXP_MR_10E_L, TXP_MR_10EX_C, MXP_MR_10DME_C, MXP_MR_10DME_L, MXP_MR_10DMEX_C, 40G-MXP-C, ADM-10G, and OTU2_XP cards.

For compliance information, refer to the Cisco Optical Transport Products Safety and Compliance Information document.

A.10.1  TXP_MR_10G Card Specifications

The TXP_MR_10G card has the following specifications:

Line (trunk side)

Bit rate:

9.95328 Gbps for OC-192/STM-64

10.70923 Gbps with ITU-T G.709 Digital Wrapper/forward error correction (FEC)

10.3125 Gbps for 10 Gigabit Ethernet (GE)

11.095 Gbps with ITU-T G.709 Digital Wrapper/FEC over 10 GE

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: 1000 ps/nm

Loopback modes: Terminal and facility


Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10G card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10G card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10G card.

Connectors: LC

Compliance Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.691

Transmitter (trunk side)

Maximum transmitter output power: +3.5 dBm

Minimum transmitter output power: +2.5 dBm

Transmitter: Lithium Niobate (LN) external modulator transmitter

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


Currently available wavelengths and versions of TXP_MR_10G (16 card versions, each covering two wavelengths):

1530.33 to 1531.12 nm (two wavelengths)

1531.90 to 1532.68 nm (two wavelengths)

1534.25 to 1535.04 nm (two wavelengths)

1535.82 to 1536.61 nm (two wavelengths)

1538.19 to 1538.98 nm (two wavelengths)

1539.77 to 1540.56 nm (two wavelengths)

1542.14 to 1542.94 nm (two wavelengths)

1543.73 to 1544.53 nm (two wavelengths)

1546.12 to 1546.92 nm (two wavelengths)

1547.72 to 1548.51 nm (two wavelengths)

1550.12 to 1550.92 nm (two wavelengths)

1551.72 to 1552.52 nm (two wavelengths)

1554.13 to 1554.94 nm (two wavelengths)

1555.75 to 1556.55 nm (two wavelengths)

1558.17 to 1558.98 nm (two wavelengths)

1559.79 to 1560.61 nm (two wavelengths)

Receiver (trunk side):

Receiver input power (no FEC, unamplified, 23 dB optical signal-to-noise ratio [OSNR], BER 1 * 10 exp - 12): -8 to -21 dBm

Receiver input power (no FEC, unamplified, 23 dB OSNR, at +/- 1000 ps/nm BER 1 * 10 exp - 12): -8 to -19 dBm

Receiver input power (no FEC, amplified, 19 dB OSNR, BER 1 * 10 exp - 12): -8 to -20 dBm

Receiver input power (no FEC, amplified, 19 dB OSNR, at +/- 1000 ps/nm BER 1 * 10 exp - 12):-8 to -18 dBm

Receiver input power (FEC, unamplified, 23 dB OSNR, BER 8 * 10 exp - 5): -8 to -24 dBm

Receiver input power (FEC, unamplified, 23 dB OSNR, at +/- 1000 ps/nm, BER 8 * 10 exp - 5): -8 to -22 dBm

Receiver input power (FEC, amplified, 9 dB OSNR, BER 8 * 10 exp - 5): -8 to -18 dBm

Receiver input power (FEC, unamplified, 11 dB OSNR, at +/- 800 ps/nm, BER 8 * 10 exp - 5): -8 to -18 dBm

Line (client side)

Bit rate: 9.95328 Gbps or 10.3125 Gbps

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: Compliant with SR-1 specification for OC-192. In the case of 10 GE, the allowance is up to 10 km of single-mode fiber (SMF) dispersion.

Loopback modes: Terminal and facility

Connectors: LC

Transmitter (client side)

Maximum transmitter output power: -1 dBm

Minimum transmitter output power: -6 dBm

Center wavelength: 1290 to 1330 nm

Nominal wavelength: 1310 nm

Transmitter: Distributed feedback (DFB) laser

Receiver (client side)

Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12

Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12

Receiver: avalanche photodiode (APD)

Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12

Receiver input wavelength range: 1290 to 1605 nm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 3.1 lb (1.3 kg)

A.10.2  MXP_2.5G_10G Card Specifications

The MXP_2.5G_10G card has the following specifications:

Line (trunk side)

Bit rate:

9.95328 Gbps for OC-192/STM-64

10.70923 Gbps with ITU-T G.709 Digital Wrapper/FEC

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: 1000 ps/nm

Loopback modes: Terminal and facility


Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10G card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10G card. Using direct fiber loopbacks causes irreparable damage to the MXP_2.5G_10G card.

Connectors: LC

Transmitter (trunk side)

Maximum transmitter output power: +3.5 dBm

Minimum transmitter output power: +2.5 dBm

Transmitter: LN external modulator transmitter

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


Currently available wavelengths and versions of MXP_2.5G_10G (16 card versions, each covering two wavelengths):

1530.33 to 1531.12 nm (two wavelengths)

1531.90 to 1532.68 nm (two wavelengths)

1534.25 to 1535.04 nm (two wavelengths)

1535.82 to 1536.61 nm (two wavelengths)

1538.19 to 1538.98 nm (two wavelengths)

1539.77 to 1540.56 nm (two wavelengths)

1542.14 to 1542.94 nm (two wavelengths)

1543.73 to 1544.53 nm (two wavelengths)

1546.12 to 1546.92 nm (two wavelengths)

1547.72 to 1548.51 nm (two wavelengths)

1550.12 to 1550.92 nm (two wavelengths)

1551.72 to 1552.52 nm (two wavelengths)

1554.13 to 1554.94 nm (two wavelengths)

1555.75 to 1556.55 nm (two wavelengths)

1558.17 to 1558.98 nm (two wavelengths)

1559.79 to 1560.61 nm (two wavelengths)

Receiver (trunk side)

Receiver input power (no FEC, unamplified, 23 dB OSNR, BER 1 * 10 exp - 12): -8 to -21 dBm

Receiver input power (no FEC, unamplified, 23 dB OSNR, at +/- 1000 ps/nm BER 1 * 10 exp - 12): -8 to -19 dBm

Receiver input power (no FEC, amplified, 19 dB OSNR, BER 1 * 10 exp - 12): -8 to -20 dBm

Receiver input power (no FEC, amplified, 19 dB OSNR, at +/- 1000 ps/nm BER 1 * 10 exp - 12): -8 to -18 dBm

Receiver input power (FEC, unamplified, 23 dB OSNR, BER 8 * 10 exp - 5): -8 to -24 dBm

Receiver input power (FEC, unamplified, 23 dB OSNR, at +/- 1000 ps/nm, BER 8 * 10 exp - 5): -8 to -22 dBm

Receiver input power (FEC, amplified, 9 dB OSNR, BER 8 * 10 exp - 5): -8 to -18 dBm

Receiver input power (FEC, unamplified, 11 dB OSNR, at +/- 800 ps/nm, BER 8 * 10 exp - 5): -8 to -18 dBm

Line (client side)

Bit rate: 2.48832 Gbps

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: Compliant with SR-1 specification for OC-192. In the case of 10 GE, allowance is up to 10 km of SMF fiber of dispersion.

Loopback modes: Terminal and facility

Connectors: LC

Transmitter (client side): Depends on the Small Form-factor Pluggable (SFP) that is used.

Receiver (client side): Depends on the SFP that is used.

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 3.1 lb (1.3 kg)

A.10.3  TXP_MR_2.5G and TXPP_MR_2.5G Card Specifications

The TXP_MR_2.5G and TXPP_MR_2.5G cards have the following specifications:

Line (trunk side)

Bit rate:

2.488 Gbps for OC-48/STM-16

2.66 Gbps with ITU-T G.709 Digital Wrapper/FEC

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: 5400 ps/nm

Loopback modes: Terminal and facility


Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the TXP_MR_2.5G and TXPP_MR_2.5G cards in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_2.5G and TXPP_MR_2.5G cards. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_2.5G and TXPP_MR_2.5G cards.

Connectors: LC

Transmitter (trunk side)

Maximum transmitter output power: +1 dBm

Minimum transmitter output power: -4.5 dBm

Transmitter: Direct modulated laser

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


Currently available wavelengths of TXP_MR_2.5G and TXPP_MR_2.5G (eight card versions):

ITU grid blue band: 1530.334 to 1544.526 nm (four card versions covering four wavelengths each)

ITU grid red band: 1546.119 to 1560.606 nm (four card versions covering four wavelengths each)

Receiver (trunk side, see Table A-34)

Table A-34 TXP_MR_2.5G/TXPP_MR_2.5G Card Receiver Trunk Side Specifications 

OSNR 1
FEC Type
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity
Chromatic Dispersion Tolerance

22 dB

Off - 2R

< 10 exp - 12

N/A

- 9 to - 24 dBm

22 dB

Off - 2R

< 10 exp - 12

N/A

- 9 to - 21 dBm

+/- 3300ps/nm

21 dB

Off - 3R

< 10 exp - 12

N/A

- 9 to - 30 dBm

22 dB

Off - 3R

< 10 exp - 12

N/A

- 9 to - 30 dBm

+/- 1800ps/nm

23 dB

Off - 3R

< 10 exp - 12

N/A

- 9 to - 30 dBm

+/- 5400ps/nm

12 dB

Standard- 3R

< 10 exp - 5

< 10 exp - 15

- 9 to - 25 dBm

12 dB

Standard- 3R

< 10 exp - 5

< 10 exp - 15

- 9 to - 24 dBm

+/- 1800ps/nm

12 dB

Standard- 3R

< 10 exp - 5

< 10 exp - 15

- 9 to - 23 dBm

+/- 5400ps/nm

21 dB

Standard- 3R

< 10 exp - 5

< 10 exp - 15

- 9 to - 31 dBm

1 OSNR defined with 0.1 nm resolution bandwidth (RBW)


Receiver: APD

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Line (client side)

Bit rate: 8 Mbps to 2.488 Gbps

Code: Scrambled NRZ

Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)

Maximum chromatic dispersion allowance: Based on SFP

Loopback modes: Terminal and facility

Connectors: LC

Transmitter (client side)

Maximum transmitter output power: -1 dBm

Minimum transmitter output power: -6 dBm

Center wavelength: Based on SFP

Nominal wavelength: Based on SFP

Transmitter: Based on SFP

Receiver (client side)

Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12

Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12

Receiver: APD

Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12

Receiver input wavelength range: 850nm to 1605 nm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 3.1 lb (1.3 kg)

A.10.4  MXP_MR_2.5G and MXPP_MR_2.5G Card Specifications

The MXP_MR_2.5G and MXPP_MR_2.5G cards have the following specifications:

Payload configuration

FC1G—Fibre Channel 1.06 Gbps

FC2G—Fibre Channel 2.125 Gbps

FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)

FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)

ESCON—Enterprise System Connection 200 Mbps

ONE_GE—One Gigabit Ethernet 1.125 Gbps

Mixed configurations up to maximum line rate of 2.5 Gbps (for example, if you have a port configured for FC2G, you cannot use another port at the same time). See the "MXP_MR_2.5G and MXPP_MR_2.5G Cards" section for more information on mixed-mode operation.

Client ports: 8x SFP

Performance monitoring (PM) for all interfaces

Buffer-to-buffer credit management for distance extension

Line (trunk side)

Bit rate: 2.488 Gbps for OC-48/STM-16

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: 6000 ps/nm

Loopback modes: Terminal and facility


Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_2.5G and MXPP_MR_2.5G cards in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_2.5G and MXPP_MR_2.5G cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_2.5G and MXPP_MR_2.5G cards.

Connectors: LC

Transmitter (trunk side)

Transmit power: +3 +/- 1 dBm with MXP_MR_2.5G card, and +/- 1 dBm with MXPP_MR_2.5G card

50-GHz DWDM migration ready (the wavelength deviation is less than +/- 0.040 nm through wavelocker deployment)

Four-channel wavelength tunability at 100-GHz spacing

Transmitter maximum return reflectance: -27 dB

Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB

Minimum side mode suppression ratio: 30 dB

Transmitter is a direct modulated laser

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


Currently available wavelengths of the TXP_MR_2.5G and TXPP_MR_2.5G cards (eight card versions):

ITU grid blue band: 1530.334 to 1544.526 nm (four card versions, four wavelengths each)

ITU grid red band: 1546.119 to 1560.606 nm (four card versions, four wavelengths each)

Receiver (trunk side, see Table A-35)

Table A-35 MXP_MR_2.5G/MXPP_MR_2.5G Card Receiver Trunk Side Specifications 

OSNR 1
FEC Type
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity
Chromatic Dispersion Tolerance

17 dB

N/A

< 10 exp - 12

N/A

- 9 to - 23 dBm

17 dB

N/A

< 10 exp - 12

N/A

- 9 to - 22 dBm

+/- 1800 ps/nm

17 dB

N/A

< 10 exp - 12

N/A

- 9 to - 21 dBm

+/- 5400 ps/nm

18 dB

N/A

< 10 exp - 12

N/A

- 9 to - 23 dBm

+/- 1800 ps/nm

19 dB

N/A

< 10 exp - 12

N/A

- 9 to - 23 dBm

+/- 5400 ps/nm

21 dB

N/A

< 10 exp - 12

N/A

- 9 to - 30 dBm

21 dB

N/A

< 10 exp - 12

N/A

- 9 to - 29 dBm

+/- 1800 ps/nm

21 dB

N/A

< 10 exp - 12

N/A

- 9 to - 28 dBm

+/- 5400 ps/nm

22 dB

N/A

< 10 exp - 12

N/A

- 9 to - 30 dBm

+/- 1800 ps/nm

23 dB

N/A

< 10 exp - 12

N/A

- 9 to - 30 dBm

+/- 5400 ps/nm

1 OSNR defined with 0.1 nm RBW


Receiver sensitivity -28 dBm, BER 1 * 10 exp - 12

Receiver overload is equal to or exceeds -8 dBm

Receiver maximum reflectance of -27 dB

Line (client side)

Bit rate: 200Mbps or 1.06 Gbps to 2.125 Gbps per client

Code: Scrambled NRZ

Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)

Loopback modes: Terminal and facility

Connectors: LC

Transmitter (client side)

Maximum transmitter output power: -1 dBm

Minimum transmitter output power: -6 dBm

Center wavelength: Based on SFP

Nominal wavelength: Based on SFP

Transmitter: Based on SFP

Receiver (client side)

Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12

Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12

Receiver: APD

Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12

Receiver input wavelength range: 1290 to 1605 nm or 850nm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 2.25 lb (1.02 kg)

A.10.5  MXP_2.5G_10E Card Specifications

The MXP_2.5G_10E card has the following specifications:

Line (trunk side)

Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)

Loopback modes: Terminal and facility


Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10E card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10E card. Using direct fiber loopbacks causes irreparable damage to the MXP_2.5G_10E card.

Connectors: LC

Transmitter (trunk side)

Maximum transmitter output power: +6 dBm

Minimum transmitter output power: +3 dBm

Transmitter: LN external modulator transmitter

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


Currently available wavelengths and versions of MXP_2.5G_10E (eight card versions):

ITU grid blue band:

1530.33 to 1533.07 nm (four channels)

1534.25 to 1537.00 nm (four channels)

1538.19 to 1540.95 nm (four channels)

1542.14 to 1544.92 nm (four channels)

ITU grid red band:

1546.12 to 1548.92 nm (four channels)

1550.12 to 1552.93 nm (four channels)

1554.13 to 1556.96 nm (four channels)

1558.17 to 1561.01 nm (four channels)

Receiver (trunk side, see Table A-36)

Receiver: APD

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Table A-36 MXP_2.5G_10E Card Receiver Trunk Side Specifications 

OSNR 1
FEC Type
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity 2
Chromatic Dispersion Tolerance

30 dB

Off

< 10 exp - 12

N/A

- 8 to - 20 dBm

+/- 1200 ps/nm

26 dB

Off

< 10 exp - 12

N/A

- 8 to - 20 dBm

+/- 1000 ps/nm

26 dB

Off

< 10 exp - 12

N/A

- 8 to - 22 dBm

17 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 18 dBm

+/- 800 ps/nm

15 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 18 dBm

15 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 18 dBm

+/- 800 ps/nm

14 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 18 dBm

1 OSNR defined with 0.1 nm RBW

2 Receiver filter bandwidth greater than or equal to 180 pm (at - 3 dBm)


Line (client side)

Bit rate: 2.5 Gbps per port (OC-48/STM-16)

Code: Scrambled NRZ

Fiber: 1310-nm single-mode

Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)

Loopback modes: Terminal and facility

Connectors: LC (optical)

Transmitter (client side): Depends on the SFP that is used.

Receiver (client side): Depends on the SFP that is used.

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 3.1 lb (1.3 kg)

A.10.6  MXP_2.5G_10E_C Card Specifications

The MXP_2.5G_10E_C card has the following specifications:

Line (trunk side)

Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)

Loopback modes: Terminal and facility


Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10E_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10E_C card. Using direct fiber loopbacks causes irreparable damage to the card.

Connectors: LC

Transmitter (trunk side)

Maximum transmitter output power: +6 dBm

Minimum transmitter output power: +3 dBm

Transmitter: LN external modulator transmitter

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


Currently available wavelengths and versions of MXP_2.5G_10E_C card:

There is a single version of the MXP_2.5G_10E_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-37.

Table A-37 MXP_2.5G_10E_C Card Trunk Wavelengths 

Channel Number
Frequency (THz)
Wavelength (nm)
Channel Number
Frequency (THz)
Wavelength (nm)

1

196.00

1529.55

42

193.95

1545.72

2

195.95

1529.94

43

193.90

1546.119

3

195.90

1530.334

44

193.85

1546.518

4

195.85

1530.725

45

193.80

1546.917

5

195.80

1531.116

46

193.75

1547.316

6

195.75

1531.507

47

193.70

1547.715

7

195.70

1531.898

48

193.65

1548.115

8

195.65

1532.290

49

193.60

1548.515

9

195.60

1532.681

50

193.55

1548.915

10

195.55

1533.073

51

193.50

1549.32

11

195.50

1533.47

52

193.45

1549.71

12

195.45

1533.86

53

193.40

1550.116

13

195.40

1534.250

54

193.35

1550.517

14

195.35

1534.643

55

193.30

1550.918

15

195.30

1535.036

56

193.25

1551.319

16

195.25

1535.429

57

193.20

1551.721

17

195.20

1535.822

58

193.15

1552.122

18

195.15

1536.216

59

193.10

1552.524

19

195.10

1536.609

60

193.05

1552.926

20

195.05

1537.003

61

193.00

1553.33

21

195.00

1537.40

62

192.95

1553.73

22

194.95

1537.79

63

192.90

1554.134

23

194.90

1538.186

64

192.85

1554.537

24

194.85

1538.581

65

192.80

1554.940

25

194.80

1538.976

66

192.75

1555.343

26

194.75

1539.371

67

192.70

1555.747

27

194.70

1539.766

68

192.65

1556.151

28

194.65

1540.162

69

192.60

1556.555

29

194.60

1540.557

70

192.55

1556.959

30

194.55

1540.953

71

192.50

1557.36

31

194.50

1541.35

72

192.45

1557.77

32

194.45

1541.75

73

192.40

1558.173

33

194.40

1542.142

74

192.35

1558.578

34

194.35

1542.539

75

192.30

1558.983

35

194.30

1542.936

76

192.25

1559.389

36

194.25

1543.333

77

192.20

1559.794

37

194.20

1543.730

78

192.15

1560.200

38

194.15

1544.128

79

192.10

1560.606

39

194.10

1544.526

80

192.05

1561.013

40

194.05

1544.924

81

192.00

1561.42

41

194.00

1545.32

82

191.95

1561.83


Receiver (trunk side, see Table A-38)

Table A-38 MXP_2.5G_10E_C Card Receiver Trunk Side Specifications 

OSNR 1
FEC Type
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity 2
Chromatic Dispersion Tolerance

30 dB

Off

< 10 exp - 12

N/A

- 8 to - 18 dBm

+/- 1200 ps/nm

26 dB

Off

< 10 exp - 12

N/A

- 8 to - 18 dBm

+/- 1000 ps/nm

26 dB

Off

< 10 exp - 12

N/A

- 8 to - 18 dBm

17 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 18 dBm

+/- 800 ps/nm

15.5 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 18 dBm

14 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 18 dBm

+/- 800 ps/nm

12 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 18 dBm

1 OSNR defined with 0.1 nm RBW

2 Receiver filter bandwidth 32.5GHz (at - 3 dB)


Receiver: APD

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Receiver input wavelength range: 1529 to 1562 nm

Line (client side)

Bit rate: 2.5 Gbps per port (OC-48/STM-16)

Code: Scrambled NRZ

Fiber: 1310-nm single-mode

Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)

Loopback modes: Terminal and facility

Connectors: LC (optical)

Transmitter (client side): Depends on the SFP that is used.

Receiver (client side): Depends on the SFP that is used.

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 3.1 lb (1.3 kg)

A.10.7  MXP_2.5G_10E_L Card Specifications

The MXP_2.5G_10E_L card has the following specifications:

Line (trunk side)

Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)

Loopback modes: Terminal and facility


Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10E_L card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10E_L card. Using direct fiber loopbacks causes irreparable damage to the card.

Connectors: LC

Transmitter (trunk side)

Maximum transmitter output power: +6 dBm

Minimum transmitter output power: +3 dBm

Transmitter: LN external modulator transmitter

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


Currently available wavelengths and versions of MXP_2.5G_10E_L card:

There is a single version of the MXP_2.5G_10E_L card. It is tunable across 80 wavelengths in the L band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-39.

Table A-39 MXP_2.5G_10E_L Card Trunk Wavelengths 

Channel Number
Frequency (THz)
Wavelength (nm)
Channel Number
Frequency (THz)
Wavelength (nm)

1

190.85

1570.83

41

188.85

1587.46

2

190.8

1571.24

42

188.8

1587.88

3

190.75

1571.65

43

188.75

1588.30

4

190.7

1572.06

44

188.7

1588.73

5

190.65

1572.48

45

188.65

1589.15

6

190.6

1572.89

46

188.6

1589.57

7

190.55

1573.30

47

188.55

1589.99

8

190.5

1573.71

48

188.5

1590.41

9

190.45

1574.13

49

188.45

1590.83

10

190.4

1574.54

50

188.4

1591.26

11

190.35

1574.95

51

188.35

1591.68

12

190.3

1575.37

52

188.3

1592.10

13

190.25

1575.78

53

188.25

1592.52

14

190.2

1576.20

54

188.2

1592.95

15

190.15

1576.61

55

188.15

1593.37

16

190.1

1577.03

56

188.1

1593.79

17

190.05

1577.44

57

188.05

1594.22

18

190

1577.86

58

188

1594.64

19

189.95

1578.27

59

187.95

1595.06

20

189.9

1578.69

60

187.9

1595.49

21

189.85

1579.10

61

187.85

1595.91

22

189.8

1579.52

62

187.8

1596.34

23

189.75

1579.93

63

187.75

1596.76

24

189.7

1580.35

64

187.7

1597.19

25

189.65

1580.77

65

187.65

1597.62

26

189.6

1581.18

66

187.6

1598.04

27

189.55

1581.60

67

187.55

1598.47

28

189.5

1582.02

68

187.5

1598.89

29

189.45

1582.44

69

187.45

1599.32

30

189.4

1582.85

70

187.4

1599.75

31

189.35

1583.27

71

187.35

1600.17

32

189.3

1583.69

72

187.3

1600.60

33

189.25

1584.11

73

187.25

1601.03

34

189.2

1584.53

74

187.2

1601.46

35

189.15

1584.95

75

187.15

1601.88

36

189.1

1585.36

76

187.1

1602.31

37

189.05

1585.78

77

187.05

1602.74

38

189

1586.20

78

187

1603.17

39

188.95

1586.62

79

186.95

1603.60

40

188.9

1587.04

80

186.9

1604.03


Receiver (trunk side, see Table A-40)

Table A-40 MXP_2.5G_10E_L Card Receiver Trunk Side Specifications 

OSNR 1
FEC Type
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity 2
Chromatic Dispersion Tolerance

30 dB

Off

< 10 exp - 12

N/A

- 8 to - 20 dBm

+/- 1200 ps/nm

26 dB

Off

< 10 exp - 12

N/A

- 8 to - 20 dBm

+/- 1000 ps/nm

26 dB

Off

< 10 exp - 12

N/A

- 8 to - 22 dBm

17 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 18 dBm

+/- 800 ps/nm

15.5 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 18 dBm

15 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 18 dBm

+/- 800 ps/nm

13 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 18 dBm

1 OSNR defined with 0.1 nm RBW

2 Receiver filter bandwidth greater than or equal to 180 pm (at - 3 dBm)


Receiver: APD

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Receiver input wavelength range: 1570 to 1604 nm

Line (client side)

Bit rate: 2.5 Gbps per port (OC-48/STM-16)

Code: Scrambled NRZ

Fiber: 1310-nm single-mode

Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)

Loopback modes: Terminal and facility

Connectors: LC (optical)

Transmitter (client side): Depends on the SFP that is used.

Receiver (client side): Depends on the SFP that is used.

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 3.1 lb (1.3 kg)

A.10.8  MXP_2.5G_10EX_C Card Specifications

The MXP_2.5G_10EX_C card has the following specifications:

Line (trunk side)

Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: +/- 1600 ps/nm (specified penalty)

Loopback modes: Terminal and facility


Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10EX_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10EX_C card. Using direct fiber loopbacks causes irreparable damage to the card.

Connectors: LC

Transmitter (trunk side)

Maximum transmitter output power: +6 dBm

Minimum transmitter output power: +3 dBm

Transmitter: LN external modulator transmitter

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


Currently available wavelengths and versions of MXP_2.5G_10EX_C card:

There is a single version of the MXP_2.5G_10EX_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-37.

Table A-41 MXP_2.5G_10EX_C Card Trunk Wavelengths 

Channel Number
Frequency (THz)
Wavelength (nm)
Channel Number
Frequency (THz)
Wavelength (nm)

1

196.00

1529.55

42

193.95

1545.72

2

195.95

1529.94

43

193.90

1546.12

3

195.90

1530.334

44

193.85

1546.52

4

195.85

1530.725

45

193.80

1546.92

5

195.80

1531.116

46

193.75

1547.32

6

195.75

1531.507

47

193.70

1547.72

7

195.70

1531.898

48

193.65

1548.11

8

195.65

1532.290

49

193.60

1548.51

9

195.60

1532.681

50

193.55

1548.91

10

195.55

1533.073

51

193.50

1549.32

11

195.50

1533.47

52

193.45

1549.72

12

195.45

1533.86

53

193.40

1550.12

13

195.40

1534.250

54

193.35

1550.52

14

195.35

1534.643

55

193.30

1550.92

15

195.30

1535.036

56

193.25

1551.32

16

195.25

1535.429

57

193.20

1551.72

17

195.20

1535.822

58

193.15

1552.12

18

195.15

1536.216

59

193.10

1552.52

19

195.10

1536.609

60

193.05

1552.93

20

195.05

1537.003

61

193.00

1553.33

21

195.00

1537.40

62

192.95

1553.73

22

194.95

1537.79

63

192.90

1554.13

23

194.90

1538.186

64

192.85

1554.54

24

194.85

1538.581

65

192.80

1554.94

25

194.80

1538.976

66

192.75

1555.34

26

194.75

1539.371

67

192.70

1555.75

27

194.70

1539.766

68

192.65

1556.15

28

194.65

1540.162

69

192.60

1556.55

29

194.60

1540.557

70

192.55

1556.96

30

194.55

1540.953

71

192.50

1557.36

31

194.50

1541.35

72

192.45

1557.77

32

194.45

1541.75

73

192.40

1558.17

33

194.40

1542.142

74

192.35

1558.58

34

194.35

1542.539

75

192.30

1558.98

35

194.30

1542.936

76

192.25

1559.39

36

194.25

1543.333

77

192.20

1559.79

37

194.20

1543.730

78

192.15

1560.20

38

194.15

1544.128

79

192.10

1560.61

39

194.10

1544.526

80

192.05

1561.01

40

194.05

1544.924

81

192.00

1561.42

41

194.00

1545.32

82

191.95

1561.83


Receiver (trunk side, see Table A-42)

Table A-42 TMXP_2.5G_10EX_C Card Receiver Trunk Side Specifications 

OSNR 1
FEC Type
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity 2
Chromatic Dispersion Tolerance
PMD tolerance

16 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 20 dBm

+/- 1600 ps/nm

15 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 20 dBm

TBD

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 20 dBm

3

12.5 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 20 dBm

17 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 20 dBm

+/- 4000 ps/nm

15.2 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 20 dBm

+/- 2500 ps/nm

17.4 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 20 dBm

 

3

1 OSNR defined with 0.1 nm RBW

2 Receiver filter bandwidth 32.5GHz (at - 3 dBm)

3 PMD = 30 ps; DGD = 90 ps, hence PMD = 3000 ps^2


Receiver: APD

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Receiver input wavelength range: 1529 to 1562 nm

Line (client side)

Bit rate: 2.5 Gbps per port (OC-48/STM-16)

Code: Scrambled NRZ

Fiber: 1310-nm single-mode

Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)

Loopback modes: Terminal and facility

Connectors: LC (optical)

Transmitter (client side): Depends on the SFP that is used.

Receiver (client side): Depends on the SFP that is used.

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 3.1 lb (1.3 kg)

A.10.9  MXP_MR_10DME_C Card Specifications

The MXP_MR_10DME_C card has the following specifications:

Payload configuration

FC1G—Fibre Channel 1.06 Gbps

FC2G—Fibre Channel 2.125 Gbps

FC4G—Fibre Channel 4.25 Gbps

FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)

FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)

FICON4G—Fiber connectivity 4.25 Gbps (IBM signal)

ISC compatibility

ISC peer 1G

ISC peer 2G

ONE_GE—One Gigabit Ethernet 1.125 Gbps

Mixed configurations up to maximum line rate of 10.0 Gbps. See the "MXP_MR_10DME_C and MXP_MR_10DME_L Cards" section for more information on mixed-mode operation.

Client ports: 8x SFP

Line (trunk side)

Bit rate: 9.952 Gbps for OC-192/STM-64

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Loopback modes: Terminal and facility


Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_10DME_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_10DME_C cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_10DME_C cards.

Connectors: LC

Transmitter (trunk side)

Minimum output power: +3 dBm

Maximum output power: +6 dBm

Minimum Single-Mode Suppression Ratio (SMSR): 30 dB

Minimum optical extinction ratio: 10 dB

41 wavelength tunability at 100-GHz spacing

Receiver maximum return reflectance (Rx return loss): -27 dB

Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB

Minimum side mode suppression ratio: 30 dB

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


For available wavelengths for the MXP_MR_10DME_C card, see Table 10-29.

For the receiver trunk side, see Table A-43:

Table A-43 MXP_MR_10DME_C Card Receiver Trunk Side Specifications 

FEC Applications
OSNR 1
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity
Chromatic Dispersion Tolerance
Power Penalty
OSNR Penalty

None

23 dB

< 10 exp - 12

-8 to -20 dBm

+/- 1200 ps/nm

2 dBm

19 dB

< 10 exp - 12

-9 to -22 dBm

+/- 1000 ps/nm

2 dBm

FEC

10 dB

< 10 exp - 5

< 10 exp - 15

-8 to -18 dBm

+/- 800 ps/nm

1.5 dB

Enhanced FEC

19 dB

< 10 exp - 4

< 10 exp - 15

-8 to -26 dBm

+/- 800 ps/nm

2 dBm

2 dB

8 dB

< 10 exp - 4

< 10 exp - 15

-8 to -18 dBm

+/- 800 ps/nm

2 dBm

1.5 dB

1 OSNR defined with 0.5 nm RBW


Receiver: APD

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Receiver input wavelength range: 1529 to 1562 nm

Line (client side)

Bit rate: 1.06 Gbps to 4.25 Gbps per client

Code: Scrambled NRZ

Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)

Maximum chromatic dispersion allowance: Based on SFP

Loopback modes: Terminal and facility

Connectors: LC

Transmitter (client side)

Maximum transmitter output power: -1 dBm

Minimum transmitter output power: -6 dBm

Center wavelength: Based on SFP

Nominal wavelength: Based on SFP

Transmitter: Based on SFP

Receiver (client side)

Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12

Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12

Receiver: APD

Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12

Receiver input wavelength range: 1290 to 1605 nm or 850nm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 2.25 lb (1.02 kg)

A.10.10  MXP_MR_10DME_L Card Specifications

The MXP_MR_10DME_L card has the following specifications:

Payload configuration

FC1G—Fibre Channel 1.06 Gbps

FC2G—Fibre Channel 2.125 Gbps

FC4G—Fibre Channel 4.25 Gbps

FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)

FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)

FICON4G—Fiber connectivity 4.25 Gbps (IBM signal)

ISC compatibility

ISC peer 1G

ISC peer 2G

ONE_GE—One Gigabit Ethernet 1.125 Gbps

Mixed configurations up to maximum line rate of 10.0 Gbps. See the "MXP_MR_10DME_C and MXP_MR_10DME_L Cards" section for more information on mixed-mode operation.

Client ports: 8x SFP

Line (trunk side)

Bit rate: 9.952 Gbps for OC-192/STM-64

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Loopback modes: Terminal and facility


Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_10DME_L card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_10DME_L cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_10DME_L cards.

Connectors: LC

Transmitter (trunk side)

Minimum output power: +3 dBm

Maximum output power: +6 dBm

Minimum SMSR: 30 dB

Minimum optical extinction ratio: 10.5 dB

40 wavelength tunability at 100-GHz spacing, 80 wavelength tunability at 50-GHz spacing

Receiver maximum return reflectance (Rx return loss): -27 dB

Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB

Minimum side mode suppression ratio: 30 dB

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


For the currently available wavelengths for the MXP_MR_10DME_L card, see Table 10-30.

Table A-44 provides the receiver trunk side specifications:

Table A-44 MXP_MR_10DME_L Card Receiver Trunk Side Specifications 

FEC Applications
OSNR 1
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity
Chromatic Dispersion Tolerance
Power Penalty
OSNR Penalty

None

23 dB

< 10 exp - 12

-8 to -19 dBm

+/- 1200 ps/nm

2 dBm

19 dB

< 10 exp - 12

-9 to -19 dBm

+/- 1000 ps/nm

2 dBm

FEC

10 dB

< 10 exp - 5

< 10 exp - 15

-8 to -18 dBm

+/- 800 ps/nm

1.5 dB

Enhanced FEC

19 dB

< 10 exp - 4

< 10 exp - 15

-8 to -26 dBm

+/- 800 ps/nm

2 dB

8 dB

< 10 exp - 4

< 10 exp - 15

-8 to -18 dBm

+/- 800 ps/nm

1.5 dB

1 OSNR defined with 0.5 nm RBW


Receiver: APD

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Receiver input wavelength range: 1570 to 1604 nm

Line (client side)

Bit rate: 1.06 Gbps to 4.25 Gbps per client

Code: Scrambled NRZ

Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)

Maximum chromatic dispersion allowance: Based on SFP

Loopback modes: Terminal and facility

Connectors: LC

Transmitter (client side)

Maximum transmitter output power: -1 dBm

Minimum transmitter output power: -6 dBm

Center wavelength: Based on SFP

Nominal wavelength: Based on SFP

Transmitter: Based on SFP

Receiver (client side)

Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12

Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12

Receiver: APD

Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12

Receiver input wavelength range: 1290 to 1605 nm or 850nm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 2.25 lb (1.02 kg)

A.10.11  MXP_MR_10DMEX_C Card Specifications

The MXP_MR_10DMEX_C card has the following specifications:

Payload configuration

FC1G—Fibre Channel 1.06 Gbps

FC2G—Fibre Channel 2.125 Gbps

FC4G—Fibre Channel 4.25 Gbps

FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)

FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)

FICON4G—Fiber connectivity 4.25 Gbps (IBM signal)

ISC compatibility

ISC peer 1G

ISC peer 2G

ONE_GE—One Gigabit Ethernet 1.125 Gbps

Mixed configurations up to maximum line rate of 10.0 Gbps.

Client ports: 8x SFP

Line (trunk side)

Bit rate: 9.952 Gbps for OC-192/STM-64

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Loopback modes: Terminal and facility


Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_10DMEX_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_10DMEX_C cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_10DMEX_C cards.

Connectors: LC

Transmitter (trunk side)

Minimum output power: +3 dBm

Maximum output power: +7 dBm

Minimum Single-Mode Suppression Ratio (SMSR): 30 dB

Minimum optical extinction ratio: 10 dB

41 wavelength tunability at 100-GHz spacing

Receiver maximum return reflectance (Rx return loss): -27 dB

Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB

Minimum side mode suppression ratio: 30 dB

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


For available wavelengths for the MXP_MR_10DMEX_C card, see Table 10-29.

For the receiver trunk side, see Table A-45:

Table A-45 MXP_MR_10DMEX_C Card Receiver Trunk Side Specifications 

OSNR 1
FEC Type
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity 2
Chromatic Dispersion Tolerance
PMD tolerance

16 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 20 dBm

+/- 1600 ps/nm

15 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 20 dBm

TBD

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 20 dBm

3

12.5 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 20 dBm

17 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 20 dBm

+/- 4000 ps/nm

15.2 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 20 dBm

+/- 2500 ps/nm

17.4 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 20 dBm

 

3

1 OSNR defined with 0.1 nm RBW

2 Receiver filter bandwidth 32.5GHz (at - 3 dBm)

3 PMD = 30 ps; DGD = 90 ps, hence PMD = 3000 ps^2


Receiver: APD

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Receiver input wavelength range: 1529 to 1562 nm

Line (client side)

Bit rate: 1.06 Gbps to 4.25 Gbps per client

Code: Scrambled NRZ

Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)

Maximum chromatic dispersion allowance: Based on SFP

Loopback modes: Terminal and facility

Connectors: LC

Transmitter (client side)

Maximum transmitter output power: -1 dBm

Minimum transmitter output power: -6 dBm

Center wavelength: Based on SFP

Nominal wavelength: Based on SFP

Transmitter: Based on SFP

Receiver (client side)

Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12

Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12

Receiver: APD

Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12

Receiver input wavelength range: 1290 to 1605 nm or 850nm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 2.25 lb (1.02 kg)

A.10.12  TXP_MR_10E Card Specifications

The TXP_MR_10E card has the following specifications:

Line (trunk side)

Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)

Loopback modes: Terminal and facility


Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10E card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10E card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10E card.

Connectors: LC

Transmitter (trunk side)

Maximum transmitter output power: +6 dBm

Minimum transmitter output power: +3 dBm for C-band and +2 dBm for L-band

Transmitter: LN external modulator transmitter

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


Currently available wavelengths and versions of TXP_MR_10E:

C-band frequency plan (eight card versions, each with four tunable channels on the ITU 100-GHz grid):

1530.33 to 1533.07 nm (four channels)

1534.25 to 1537.00 nm (four channels)

1538.19 to 1540.95 nm (four channels)

1542.14 to 1544.92 nm (four channels)

1546.12 to 1548.92 nm (four channels)

1550.12 to 1552.93 nm (four channels)

1554.13 to 1556.96 nm (four channels)

1558.17 to 1561.01 nm (four channels)

L-band frequency plan (five card versions, each with eight tunable channels on the ITU 50-GHz grid):

1577.44 to 1580.35 nm (eight channels)

1580.77 to 1583.69 nm (eight channels)

1584.11 to 1587.04 nm (eight channels)

1587.46 to 1590.41 nm (eight channels)

1590.83 to 1593.79 nm (eight channels)

Receiver (trunk side, see Table A-46)

Table A-46 TXP_MR_10E Card Receiver Trunk Side Specifications 

OSNR 1
FEC Type
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity 2
Chromatic Dispersion Tolerance

30 dB

Off

< 10 exp - 12

N/A

- 8 to - 20 dBm

+/- 1200 ps/nm

26 dB

Off

< 10 exp - 12

N/A

- 8 to - 20 dBm

+ - 1000 ps/nm

26 dB

Off

< 10 exp - 12

N/A

- 8 to - 22 dBm

17 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 18 dBm

+/- 800 ps/nm

15 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 18 dBm

15 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 18 dBm

+/- 800 ps/nm

14 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 18 dBm

1 OSNR defined with 0.1 nm RBW

2 Receiver filter bandwidth greater than or equal to 180 pm (at - 3 dBm)


Receiver: APD

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Line (client side):

10-Gigabit Small Form-factor Pluggable (XFP)-based SR

Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192

Code: Scrambled NRZ

Fiber: 1310-nm single-mode

Maximum chromatic dispersion allowance: 6.6 ps/nm

Loopback modes: Terminal and facility

Connectors: LC

Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957, ITU-T G.691

Transmitter (client side)

Maximum transmitter output power: -1 dBm

Minimum transmitter output power: -6 dBm

Center wavelength: 1290 to 1330 nm

Nominal wavelength: 1310 nm

Transmitter: DFB laser

Receiver (client side)

Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12

Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12

Receiver: APD

Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12

Receiver input wavelength range: 1290 to 1605 nm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 3.1 lb (1.3 kg)

A.10.13  TXP_MR_10E_C Card Specifications

The TXP_MR_10E_C card has the following specifications:

Line (trunk side)

Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)

Loopback modes: Terminal and facility


Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10E_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10E_C card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10E_C card.

Connectors: LC

Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957, and ITU-T G.709

Transmitter (trunk side)

Maximum transmitter output power: +6 dBm

Minimum transmitter output power: +3 dBm

Transmitter: LN external modulator transmitter

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


Currently available wavelengths and versions of TXP_MR_10E_C card:

There is a single version of the TXP_MR_10E_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-47.

Table A-47 TXP_MR_10E_C Card Trunk Wavelengths 

Channel Number
Frequency (THz)
Wavelength (nm)
Channel Number
Frequency (THz)
Wavelength (nm)

1

196.00

1529.55

42

193.95

1545.72

2

195.95

1529.94

43

193.90

1546.119

3

195.90

1530.334

44

193.85

1546.518

4

195.85

1530.725

45

193.80

1546.917

5

195.80

1531.116

46

193.75

1547.316

6

195.75

1531.507

47

193.70

1547.715

7

195.70

1531.898

48

193.65

1548.115

8

195.65

1532.290

49

193.60

1548.515

9

195.60

1532.681

50

193.55

1548.915

10

195.55

1533.073

51

193.50

1549.32

11

195.50

1533.47

52

193.45

1549.71

12

195.45

1533.86

53

193.40

1550.116

13

195.40

1534.250

54

193.35

1550.517

14

195.35

1534.643

55

193.30

1550.918

15

195.30

1535.036

56

193.25

1551.319

16

195.25

1535.429

57

193.20

1551.721

17

195.20

1535.822

58

193.15

1552.122

18

195.15

1536.216

59

193.10

1552.524

19

195.10

1536.609

60

193.05

1552.926

20

195.05

1537.003

61

193.00

1553.33

21

195.00

1537.40

62

192.95

1553.73

22

194.95

1537.79

63

192.90

1554.134

23

194.90

1538.186

64

192.85

1554.537

24

194.85

1538.581

65

192.80

1554.940

25

194.80

1538.976

66

192.75

1555.343

26

194.75

1539.371

67

192.70

1555.747

27

194.70

1539.766

68

192.65

1556.151

28

194.65

1540.162

69

192.60

1556.555

29

194.60

1540.557

70

192.55

1556.959

30

194.55

1540.953

71

192.50

1557.36

31

194.50

1541.35

72

192.45

1557.77

32

194.45

1541.75

73

192.40

1558.173

33

194.40

1542.142

74

192.35

1558.578

34

194.35

1542.539

75

192.30

1558.983

35

194.30

1542.936

76

192.25

1559.389

36

194.25

1543.333

77

192.20

1559.794

37

194.20

1543.730

78

192.15

1560.200

38

194.15

1544.128

79

192.10

1560.606

39

194.10

1544.526

80

192.05

1561.013

40

194.05

1544.924

81

192.00

1561.42

41

194.00

1545.32

82

191.95

1561.83


Receiver (trunk side, see Table A-48)

Table A-48 TXP_MR_10E _C Card Receiver Trunk Side Specifications 

OSNR 1
FEC Type
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity 2
Chromatic Dispersion Tolerance

30 dB

Off

< 10 exp - 12

N/A

- 8 to - 18 dBm

+/- 1200 ps/nm

26 dB

Off

< 10 exp - 12

N/A

- 8 to - 18 dBm

+ - 1000 ps/nm

26 dB

Off

< 10 exp - 12

N/A

- 8 to - 18 dBm

17 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 18 dBm

+/- 800 ps/nm

15.5 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 18 dBm

14 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 18 dBm

+/- 800 ps/nm

12 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 18 dBm

1 OSNR defined with 0.1 nm RBW

2 Receiver filter bandwidth 32.5GHz (at - 3 dB)


Receiver: APD

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Receiver input wavelength range: 1529 to 1562 nm

Line (client side):

XFP-based SR

Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192

Code: Scrambled NRZ

Fiber: 1310-nm single-mode

Maximum chromatic dispersion allowance: 6.6 ps/nm

Loopback modes: Terminal and facility

Connectors: LC

Transmitter (client side)

Maximum transmitter output power: -1 dBm

Minimum transmitter output power: -6 dBm

Center wavelength: 1290 to 1330 nm

Nominal wavelength: 1310 nm

Transmitter: DFB laser

Receiver (client side)

Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12

Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12

Receiver: APD

Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12

Receiver input wavelength range: 1290 to 1605 nm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 3.1 lb (1.3 kg)

A.10.14  TXP_MR_10E_L Card Specifications

The TXP_MR_10E_L card has the following specifications:

Line (trunk side)

Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)

Loopback modes: Terminal and facility


Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10E_L card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10E_L card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10E_L card.

Connectors: LC

Transmitter (trunk side)

Maximum transmitter output power: +6 dBm

Minimum transmitter output power: +2 dBm

Transmitter: LN external modulator transmitter

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


Currently available wavelengths and versions of TXP_MR_10E_L card:

There is a single version of the TXP_MR_10E_L card. It is tunable across 80 wavelengths in the L band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-49.

Table A-49 TXP_MR_10E_L Card Trunk Wavelengths 

Channel Number
Frequency (THz)
Wavelength (nm)
Channel Number
Frequency (THz)
Wavelength (nm)

1

190.85

1570.83

41

188.85

1587.46

2

190.8

1571.24

42

188.8

1587.88

3

190.75

1571.65

43

188.75

1588.30

4

190.7

1572.06

44

188.7

1588.73

5

190.65

1572.48

45

188.65

1589.15

6

190.6

1572.89

46

188.6

1589.57

7

190.55

1573.30

47

188.55

1589.99

8

190.5

1573.71

48

188.5

1590.41

9

190.45

1574.13

49

188.45

1590.83

10

190.4

1574.54

50

188.4

1591.26

11

190.35

1574.95

51

188.35

1591.68

12

190.3

1575.37

52

188.3

1592.10

13

190.25

1575.78

53

188.25

1592.52

14

190.2

1576.20

54

188.2

1592.95

15

190.15

1576.61

55

188.15

1593.37

16

190.1

1577.03

56

188.1

1593.79

17

190.05

1577.44

57

188.05

1594.22

18

190

1577.86

58

188

1594.64

19

189.95

1578.27

59

187.95

1595.06

20

189.9

1578.69

60

187.9

1595.49

21

189.85

1579.10

61

187.85

1595.91

22

189.8

1579.52

62

187.8

1596.34

23

189.75

1579.93

63

187.75

1596.76

24

189.7

1580.35

64

187.7

1597.19

25

189.65

1580.77

65

187.65

1597.62

26

189.6

1581.18

66

187.6

1598.04

27

189.55

1581.60

67

187.55

1598.47

28

189.5

1582.02

68

187.5

1598.89

29

189.45

1582.44

69

187.45

1599.32

30

189.4

1582.85

70

187.4

1599.75

31

189.35

1583.27

71

187.35

1600.17

32

189.3

1583.69

72

187.3

1600.60

33

189.25

1584.11

73

187.25

1601.03

34

189.2

1584.53

74

187.2

1601.46

35

189.15

1584.95

75

187.15

1601.88

36

189.1

1585.36

76

187.1

1602.31

37

189.05

1585.78

77

187.05

1602.74

38

189

1586.20

78

187

1603.17

39

188.95

1586.62

79

186.95

1603.60

40

188.9

1587.04

80

186.9

1604.03


Receiver (trunk side, see Table A-50)

Table A-50 TXP_MR_10E Card Receiver Trunk Side Specifications 

OSNR 1
FEC Type
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity 2
Chromatic Dispersion Tolerance

30 dB

Off

< 10 exp - 12

N/A

- 8 to - 20 dBm

+/- 1200 ps/nm

26 dB

Off

< 10 exp - 12

N/A

- 8 to - 20 dBm

+ - 1000 ps/nm

26 dB

Off

< 10 exp - 12

N/A

- 8 to - 22 dBm

17 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 18 dBm

+/- 800 ps/nm

15.5 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 18 dBm

15 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 18 dBm

+/- 800 ps/nm

13 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 18 dBm

1 OSNR defined with 0.1 nm RBW

2 Receiver filter bandwidth greater than or equal to 180 pm (at - 3 dBm)


Receiver: APD

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Receiver input wavelength range: 1570 to 1604 nm

Line (client side):

XFP-based SR

Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192

Code: Scrambled NRZ

Fiber: 1310-nm single-mode

Maximum chromatic dispersion allowance: 6.6 ps/nm

Loopback modes: Terminal and facility

Connectors: LC

Transmitter (client side)

Maximum transmitter output power: -1 dBm

Minimum transmitter output power: -6 dBm

Center wavelength: 1290 to 1330 nm

Nominal wavelength: 1310 nm

Transmitter: DFB laser

Receiver (client side)

Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12

Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12

Receiver: APD

Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12

Receiver input wavelength range: 1290 to 1605 nm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 3.1 lb (1.3 kg)

A.10.15  TXP_MR_10EX_C Card Specifications

The TXP_MR_10EX_C card has the following specifications:

Line (trunk side)

Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: +/- 1600 ps/nm (specified penalty)

Loopback modes: Terminal and facility


Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10EX_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10EX_C card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10EX_C card.

Connectors: LC

Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957, and ITU-T G.709

Transmitter (trunk side)

Maximum transmitter output power: +6 dBm

Minimum transmitter output power: +3 dBm

Transmitter: LN external modulator transmitter

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


Currently available wavelengths and versions of TXP_MR_10EX_C card:

There is a single version of the TXP_MR_10EX_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-51.

Table A-51 TXP_MR_10EX_C Card Trunk Wavelengths 

Channel Number
Frequency (THz)
Wavelength (nm)
Channel Number
Frequency (THz)
Wavelength (nm)

1

196.00

1529.55

42

193.95

1545.72

2

195.95

1529.94

43

193.90

1546.12

3

195.90

1530.334

44

193.85

1546.52

4

195.85

1530.725

45

193.80

1546.92

5

195.80

1531.116

46

193.75

1547.32

6

195.75

1531.507

47

193.70

1547.72

7

195.70

1531.898

48

193.65

1548.11

8

195.65

1532.290

49

193.60

1548.51

9

195.60

1532.681

50

193.55

1548.91

10

195.55

1533.073

51

193.50

1549.32

11

195.50

1533.47

52

193.45

1549.72

12

195.45

1533.86

53

193.40

1550.12

13

195.40

1534.250

54

193.35

1550.52

14

195.35

1534.643

55

193.30

1550.92

15

195.30

1535.036

56

193.25

1551.32

16

195.25

1535.429

57

193.20

1551.72

17

195.20

1535.822

58

193.15

1552.12

18

195.15

1536.216

59

193.10

1552.52

19

195.10

1536.609

60

193.05

1552.93

20

195.05

1537.003

61

193.00

1553.33

21

195.00

1537.40

62

192.95

1553.73

22

194.95

1537.79

63

192.90

1554.13

23

194.90

1538.186

64

192.85

1554.54

24

194.85

1538.581

65

192.80

1554.94

25

194.80

1538.976

66

192.75

1555.34

26

194.75

1539.371

67

192.70

1555.75

27

194.70

1539.766

68

192.65

1556.15

28

194.65

1540.162

69

192.60

1556.55

29

194.60

1540.557

70

192.55

1556.96

30

194.55

1540.953

71

192.50

1557.36

31

194.50

1541.35

72

192.45

1557.77

32

194.45

1541.75

73

192.40

1558.17

33

194.40

1542.142

74

192.35

1558.58

34

194.35

1542.539

75

192.30

1558.98

35

194.30

1542.936

76

192.25

1559.39

36

194.25

1543.333

77

192.20

1559.79

37

194.20

1543.730

78

192.15

1560.20

38

194.15

1544.128

79

192.10

1560.61

39

194.10

1544.526

80

192.05

1561.01

40

194.05

1544.924

81

192.00

1561.42

41

194.00

1545.32

82

191.95

1561.83


Receiver (trunk side, see Table A-48)

Table A-52 TXP_MR_10E _C Card Receiver Trunk Side Specifications 

OSNR 1
FEC Type
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity 2
Chromatic Dispersion Tolerance
PMD tolerance

16 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 20 dBm

+/- 1600 ps/nm

15 dB

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 20 dBm

TBD

Standard

< 10 exp - 5

< 10 exp - 15

- 8 to - 20 dBm

3

12.5 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 20 dBm

17 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 20 dBm

+/- 4000 ps/nm

15.2 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 20 dBm

+/- 2500 ps/nm

17.4 dB

Enhanced

< 7 x 10 exp - 4

< 10 exp - 15

- 8 to - 20 dBm

 

3

1 OSNR defined with 0.1 nm RBW

2 Receiver filter bandwidth 32.5GHz (at - 3 dBm)

3 PMD = 30 ps; DGD = 90 ps, hence PMD = 3000 ps^2


Receiver: APD

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Receiver input wavelength range: 1529 to 1562 nm

Line (client side):

XFP-based SR

Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192

Code: Scrambled NRZ

Fiber: 1310-nm single-mode

Maximum chromatic dispersion allowance: 6.6 ps/nm

Loopback modes: Terminal and facility

Connectors: LC

Transmitter (client side)

Maximum transmitter output power: -1 dBm

Minimum transmitter output power: -6 dBm

Center wavelength: 1290 to 1330 nm

Nominal wavelength: 1310 nm

Transmitter: DFB laser

Receiver (client side)

Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12

Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12

Receiver: APD

Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12

Receiver input wavelength range: 1290 to 1605 nm

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 3.1 lb (1.3 kg)

A.10.16  40G-MXP-C Card Specifications

The 40G-MXP-C card has the following specifications:

Payload configuration

FC8G—Fibre Channel 8.50 Gbps

FC10G—Fiber Channel 10.519 Gbps

FICON10G—Fiber connectivity 10.519 Gbps

OC192/STM64/10GE WAN-Phy—9.953 Gbps

10-GE LAN-Phy—10.312 Gbps

OTU2 (OC192/STM64/10GE WAN-Phy)—10.709 Gbps

OTU2e (10GE LAN-Phy)—11.096 Gbps

Client ports: 4 X SFP

Line (trunk side)

Bit rate: 43.018 Gbps for OTU3, 44.57 Gbps for OTU3e

Code: RZ-DQPSK 40G

Fiber: 1550-nm single-mode

Loopback modes: Terminal and facility


Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the 40G-MXP-C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the 40G-MXP-C cards. Using direct fiber loopbacks causes irreparable damage to the 40G-MXP-C cards.

Connectors: LC

Transmitter (trunk side)

Minimum output power: -2 dBm

Maximum output power: +2 dBm

Minimum Single-Mode Suppression Ratio (SMSR): 35 dB

Minimum optical extinction ratio: 25 dB

Wavelength tunability (total 82 wavelengths) at 50-GHz spacing

Receiver maximum return reflectance (Rx return loss): -27 dB

Chromatic dispersion allowance: 750 ps/nm, giving an optical OSNR penalty < 2.0 dB

Minimum side mode suppression ratio: 30 dB

Wavelength stability (drift): +/- 25 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


For wavelengths available for the 40G-MXP-C card, see Table 10-29.

Receiver (trunk side)

Receiver: PIN

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Receiver input wavelength range: 1529 to 1562 nm

Table A-53 lists the trunk side specifications of the receiver.

Table A-53 40G-MXP-C Card Receiver (Trunk) Side Specifications 

FEC Applications
OSNR 1
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity
Chromatic Dispersion Tolerance
Power Penalty
OSNR Penalty

FEC

12 dB

< 10 exp - 5

< 10 exp - 15

-8 to -20 dBm

+/- 750 ps/nm

2 dB

Enhanced FEC

19 dB

< 10 exp - 3

< 10 exp - 15

-8 to -24 dBm

+/- 750 ps/nm

2 dBm

8 dB

< 10 exp - 3

< 10 exp - 15

-8 to -20 dBm

+/- 750 ps/nm

2 dB

1 OSNR defined with 0.5 nm RBW


Line (client side)

Bit rate: 8.50 Gbps to 11.096 Gbps per client

Code: NRZ 40G

Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)

Maximum chromatic dispersion allowance: Based on XFP

Loopback modes: Terminal and facility

Connectors: LC

Transmitter (client side)

Maximum transmitter output power: Based on XFP

Minimum transmitter output power: Based on XFP

Center wavelength: Based on XFP

Nominal wavelength: Based on XFP

Transmitter: Based on XFP

Receiver (client side)

Maximum receiver level: Based on XFP

Minimum receiver level: Based on XFP

Receiver: Based on XFP

Link loss budget: Based on XFP

Receiver input wavelength range: Based on XFP

Environmental Exception

Short term ambient temperature: Functionality is guaranteed, according to GR-63 Issue 3 for the thermal cycles except for the temperature values which are -5 to 45 degrees Celsius (23 to 113 degrees Fahrenheit) instead of -5 to 55 degrees Celsius (23 to 131 degrees Fahrenheit).

Dimensions

Height: 12.650 in. (321.3 mm)

Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.000 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight excluding clam shell: 7.7 lb (3.5 kg)

A.10.17  ADM-10G Card Specifications

The ADM-10G card has the following specifications:

Line

Bit rate: OC-3/STM-1 (155.520 Mb/s); OC-12/STM-3 (622.08 Mb/s); OC-48/STM-16 (2488.32 Mb/s); OC-192/STM-64 (9.95328 Gbps)

Code: Scrambled NRZ

Fiber: 1310-nm single-mode for ONS-XC-10GS1 XFP or 1530.33 to 1554.94-nm single-mode for ONS-XC-10G-xx.x XFP

Maximum chromatic dispersion allowance: up to 3600 ps/nm

Loopback modes: Terminal, facility, and cross-connect

Connectors: LC

Transmitter (trunk side)

Transmitter: LN external modulator transmitter

Maximum transmitter output power: Depends on XFP that is used

Minimum transmitter output power: Depends on XFP that is used

Wavelength stability (drift): +/- 25 picometers (pm)

Receiver (trunk side)

Receiver: APD

Receiver input wavelength range: Depends on XFP that is used

Receiver sensitivity: depends on XFP that is used

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Dimensions

Height: 12.65 in. (321.3 mm)

Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.00 in. (228.6 mm)

Depth with backplane connector: 9.250 in. (235 mm)

Weight not including clam shell: 5.07 lb (2.3 kg)

A.10.18  GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Card Specifications

The GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE cards have the following specifications:

Line (trunk side)

Bit rate: 11.1 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode) or 10.3125 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode disabled)

Code: Scrambled NRZ

Fiber: 1550-nm single-mode

Maximum chromatic dispersion allowance: - 500 to 1600 ps/nm (specified penalty)

Loopback modes: Terminal and facility


Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the GE_XP and GE_XPE card in a loopback on the trunk port. Do not use direct fiber loopbacks with the GE_XP and GE_XPE card. Using direct fiber loopbacks causes irreparable damage to the GE_XP and GE_XPE card.

Connectors: LC

Transmitter (trunk side)

Maximum transmitter output power: +3 dBm

Minimum transmitter output power: -1 dBm

Transmitter: EML laser

Wavelength stability (drift): +/- 100 picometers (pm)


Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.


Currently available wavelengths and versions of GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE: C Band, 100 GHz spacing.

Receiver (trunk side, see Table A-54)

Receiver: APD

Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion

Table A-54 GE_XP and GE_XPE Card Receiver Trunk Side Specifications 

OSNR 1
FEC Type
Pre-FEC BER
Post-FEC BER
Input Power Sensitivity 2
Chromatic Dispersion Tolerance

30 dB

Off

1.00E - 12

N/A

- 7 to - 23 dBm

30 dB

Off

1.00E - 12

N/A

- 7 to - 20 dBm

- 500 to 1600 ps/nm

24 dB

Off

1.00E - 12

N/A

- 7 to - 18 dBm

27 dB

Off

1.00E - 12

N/A

- 7 to - 18 dBm

- 500 to 1600 ps/nm

18 dB

Standard

1.00E - 05

1.00E - 15

- 7 to - 18 dBm

19 dB

Standard

1.00E - 05

1.00E - 15

- 7 to - 18 dBm

- 500 to 1600 ps/nm

30 dB

Enhanced

1.00E - 04

1.00E - 15

- 7 to - 27 dBm

30 dB

Enhanced

1.00E - 04

1.00E - 15

- 7 to - 24 dBm

- 500 to 1600 ps/nm

15 dB

Enhanced

1.00E - 04

1.00E - 15

- 7 to - 18 dBm

15 dB

Enhanced

1.00E - 04

1.00E - 15

- 7 to - 18 dBm

- 500 to 1600 ps/nm

1 OSNR defined with 0.1 nm RBW

2 Receiver filter bandwidth greater than or equal to 180 pm (at - 3 dBm)


Line (client side)

Bit rate: 1.125Gbps (GE) or 10.3125Gbps (10GE)

Code: Scrambled NRZ

Fiber: 1310-nm single-mode or 850-nm multimode

Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)

Loopback modes: Terminal and facility

Connectors: LC (optical)

Transmitter (client side): Depends on the SFP that is used.

Receiver (client side): Depends on the SFP that is used.

Environmental

Power consumption: 95.00 W (maximum), 2 A at -48 V for GE_XP and GE_XPE cards

Power consumption: 80.00 W (maximum), 1.67 A at -48 V for 10GE_XP and 10GE_XPE cards

Dimensions

Height: 12.992 in. (330 mm)

Width: 10GE_XP and 10GE_XPE: 0.921 in. (23.4 mm)
GE_XP and GE_XPE: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.448 in. (240 mm)

Weight not including clam shell: 10GE-XP and 10GE_XPE, 1.04 kg;
GE-XP and GE_XPE, 1.36 kg.

A.10.19  OTU2_XP Card Specifications

The OTU2_XP card has the following specifications:

Line

Bit rate: OC-192/STM-64 (9.95328 Gbps), 10GE (10.3125 Gbps), or 10G FC (10.51875 Gbps)

Code: Scrambled NRZ

Fiber: 1310-nm single-mode for ONS-XC-10GS1 XFP or 1530.33-nm to 1561.42-nm single-mode for ONS-XC-10G-xx.x XFP

Maximum chromatic dispersion allowance: Depends on the XFP that is used

Loopback modes: Terminal and facility

Connectors: LC

Transmitter (trunk side)

Transmitter: EML

Maximum transmitter output power: Depends on the XFP that is used

Minimum transmitter output power: Depends on the XFP that is used

Wavelength stability (drift): Depends on the XFP that is used

Receiver (trunk side)

Receiver: APD

Receiver input wavelength range: Depends on XFP that is used

Receiver sensitivity: Depends on XFP that is used

Link loss budget: Depends on XFP that is used

Dimensions

Height: 13.043 in. (331.3 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 9.413 in. (239.1 mm)

Depth with backplane connector: 9.909 in. (251.7 mm)

Weight not including clam shell: 2.38 lb (1.08 kg)

A.11  TDC-CC and TDC-FC Card Specifications

The TDC-CC and TDC-FC card specifications are as follows:

Wavelength

Total operating signal wavelength range (C-band range): 1529.0 - 1562.5 nm

Optical

Insertion loss — DC-RX to DC-TX: Maximum 12.5 for TDC-CC and 9.5 for TDC-FC @ 1545.32 nm at room temperature

Wavelength dependant loss: 0.8 dB max

Maximum optical input power: 200mW

Polarization dependent loss: 0.2 dB max

Dimensions

Height: 12.65 in. (332 mm)

Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)

Depth: 8.66 in. (220.1 mm)

Depth with backplane connector: 235 mm (9.250 in)

Weight not including clam shell:

TDC-CC—1.26 Kg

TDC-FC—1.14 Kg

The TDC-CC and TDC-FC tunable CD values are listed in Table A-55.

Table A-55 TDC-CC and TDC-FC Tunable CD Value

Unit Configuration
TDC-CC [ps/nm]
TDC-FC [ps/nm]

0

0 1

02

1

-110

-45

2

-220

-90

3

-330

-135

4

-440

-180

5

-550

-225

6

-660

-270

7

-770

-315

8

-880

-360

9

-990

-405

10

-1100

-450

11

-1210

-495

12

-1320

-540

13

-1430

-585

14

-1540

-630

15

-1650

-675

1 The default value of the TDC-CC CD value for Coarse Unit is 0.

2 The default value of the TDC-FC value for Fine Unit is 0.


A.12  Mesh Patch Panel Specifications

This section provides specifications for the PP-MESH-4, PP-MESH-8, and 15454-PP-4-SMR patch panels.

A.12.1  PP-MESH-4 Patch Panel Specifications

The PP-MESH-4 patch panel optical specifications are listed in Table A-56.

Table A-56 PP-MESH-4 Patch Panel Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Wavelength range

1530

1570

nm

Insertion loss 1 2

In all the wavelength ranges

(local ADD or test access RX to EXP TX, COM RX to EXP TX, COM RX to test access TX)

7.5

dB

Insertion Loss Uniformity1 2

In all the wavelength ranges

0.9

dB

Polarization dispersion loss (PDL) 1

0.3

dB

Polarization mode dispersion (PMD) 1

0.1

dB

Optical Return Loss 1

50

dB

Directivity 1

50

dB

1 Under all SOPs and all operating environmental conditions

2 Values are referenced with connector loss (LC=0.3 dB, MPO=0.5dB)


The PP-MESH-4 patch panel has the following additional specifications:

Environmental

Operating temperature: +23 to +149 degrees Fahrenheit (-5 to +65 degrees Celsius)

Operating humidity: 5 to 95 percent, noncondensing

Dimensions

Height: 17.42 in. (442.5 mm)

Width: 3.457 in. (87.8 mm)

Depth: 11.025 in. (280 mm)

A.12.2  PP-MESH-8 Patch Panel Specifications

The PP-MESH-8 patch panel optical specifications are listed in Table A-57.

Table A-57 PP-MESH-8 Patch Panel Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Wavelength range

1530

1570

nm

Insertion loss 1 2

In all the wavelength ranges

(local ADD or test access RX to EXP TX, COM RX to EXP TX, COM RX to test access TX)

10.6

dB

Insertion loss uniformity 1 2

In all the wavelength ranges

1.3

dB

PDL 1

0.5

dB

PMD 1

0.1

dB

Optical Return Loss 1

50

dB

Directivity 1

50

dB

1 Under all SOPs and all operating environmental conditions

2 Values are referenced with connector loss (LC=0.3 dB, MPO=0.5dB)


The PP-MESH-8 patch panel has the following additonal specifications:

Environmental

Operating temperature: +23 to +149 degrees Fahrenheit (-5 to +65 degrees Celsius)

Operating humidity: 5 to 95 percent, noncondensing

Dimensions

Height: 17.42 in. (442.5 mm)

Width: 3.457 in. (87.8 mm)

Depth: 11.025 in. (280 mm)

A.12.3  15454-PP-4-SMR Patch Panel Specifications

The 15454-PP-4-SMR patch panel optical specifications are listed in Table A-58.

Table A-58 15454-PP-4-SMR Patch Panel Optical Specifications 

Parameter
Note
Condition
Min
Max
Unit

Wavelength range

All SOP within operating temperature range

1520

1570

nm

Insertion loss

All SOP within operating temperature range, wavelength range, from each input port of any MPO connector to any output port including two MPO connections

5.5

7.5

dB

Insertion loss uniformity 1

0.5

dB

Insertion loss ripple

0.2

dB

Chromatic dispersion

+/- 5

ps/nm

PDL

0.1

dB

PMD

0.1

dB

Optical return loss

50

dB

Directivity

50.0

dB

1 Defined as the difference between theinsertion loss values of any of the four branches of each 1x4 coupler.


The 15454-PP-4-SMR patch panel has the following additional specifications:

Environmental

Operating temperature: +23 to +149 degrees Fahrenheit (-5 to +65 degrees Celsius)

A.13  SFP and XFP Specifications


Note The CC-FTA fan tray is mandatory if CWDM SFPs and DWDM SFPs are used on MSTP units.



Note Use hardware version 2.0 DWDM SFP for MSTP units.


See the Installing the GBIC, SFP, SFP+, XFP, CXP, and CFP Optical Modules in Cisco ONS Platforms for SFP and XFP specifications.

A.14  Patch Panel Specifications

For information on 15216 40-Channel Mux/Demux Patch Panel specifications, refer to the "Patch Panel Specifications" section in the "Installing Cisco ONS 15216 40-Channel Mux/Demux Patch Panel" guide.

For information on 15454-PP-4-SMR Patch Panel specifications, refer to the "Patch Panel Specifications" section in the "Installing Cisco ONS 15454-PP-4-SMR Patch Panel" guide.