A.5 Optical Amplifier Cards
This section provides specifications for the OPT-PRE amplifier, OPT-BST amplifier, OPT-BST-E amplifier, OPT-BST-L amplifier, OPT-AMP-L preamplifier (configurable as a preamplifier or booster amplifier), OPT-AMP-C amplifier (configurable as a preamplifier or booster amplifier), OPT-AMP-17-C, and OPT-RAMP-C amplifier cards.
A.5.1 OPT-PRE Amplifier Card Specifications
The OPT-PRE amplifier card has the following specifications:
– Total operating wavelength range: 1530 to 1561.3 nm
– Gain ripple (peak to valley): 1.5 dB
– Mid-access loss (MAL) range (for dispersion compensation unit [DCU]): 3 to 9 dB
– Gain range: 5 to 38.5 dBm in constant power mode, 5 to 28 dBm in constant gain mode
– Minimum gain (standard range): 5.0 dBm
– Maximum gain (standard range with programmable gain tilt): 21 dBm
– Maximum gain (extended range with uncontrolled gain tilt): 38.5 dBm
– Gain and power regulation over/undershoot: 0.5 dB
– Limited maximum output power: 17.5 dBm
– Maximum output power (with full channel load): 17 dB
– Minimum output power (with one channel): –2 dBm
– Input power (Pin) range at full channel load: –21.5 to 12 dBm
– Input power (Pin) range at single channel load: –39.5 to –6 dBm
– Noise figure at G3 21 dB = 6.5 dB
– OSC filter drop (channels) insertion loss maximum: 1 dB
– OSC filter drop (OSC) insertion loss maximum: 1.8 dB
– OSC filter add (OSC) insertion loss maximum: 1.3 dB
– Optical connectors: LC-UPC/2
– Height: 12.65 in. (332 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (240 mm)
A.5.2 OPT-BST Amplifier Card Specifications
The OPT-BST amplifier card has the following specifications:
– Total operating wavelength range: 1530 to 1561.3 nm
– Gain ripple (peak to valley): 1.5 dB
– Gain range: 5 to 20 dBm with programmable gain tilt
– Gain and power regulation over/undershoot: 0.5 dB
– Limited maximum output power: 17.5 dBm
– Maximum output power (with full channel load): 17 dB
– Minimum output power (with one channel): –2 dBm
– Input power (Pin) range at full channel load: –3 to 12 dBm
– Input power (Pin) range at single channel load: –21 to –6 dBm
– Noise figure at G3 20 dB = 6 dB
– OSC filter drop (channels) insertion loss maximum: 1 dB
– OSC filter drop (OSC) insertion loss maximum: 1.8 dB
– OSC filter add (OSC) insertion loss maximum: 1.3 dB
– Optical connectors: LC-UPC/2
– Height: 12.65 in. (332 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (240 mm)
A.5.3 OPT-BST-E Amplifier Card Specifications
The OPT-BST-E amplifier card has the following specifications:
– Total operating wavelength range: 1530 to 1561.3 nm
– Gain ripple (peak to valley): 1.8 dB
– Gain range: 8 to 23 dB with programmable gain tilt
– Extended gain range: 23 to 26 dB with gain tilt uncontrolled
– Gain and power regulation over/undershoot: 0.5 dB
– Limited maximum output power: 20.5 dBm
– Maximum output power (with full channel load): 20 dB
– Minimum output power (with one channel): –0 dBm
– Input power (Pin) range at full channel load: –6 to 12 dBm
– Input power (Pin) range at single channel load: –26 to –8 dBm
– Noise figure at G3 23 dB = 6 dB
– OSC filter drop (channels) insertion loss maximum: 1 dB
– OSC filter drop (OSC) insertion loss maximum: 1.8 dB
– OSC filter add (OSC) insertion loss maximum: 1.3 dB
– Optical connectors: LC-UPC/2
– Height: 12.65 in. (332 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (240 mm)
A.5.4 OPT-BST-L Amplifier Card Specifications
The OPT-BST-L amplifier card has the following specifications:
– Total operating wavelength range: 1570.0 to 1605.0 nm
– Gain ripple (peak to valley): 1.5 dB
– Gain range: 8 to 20 dB with programmable gain tilt
– Extended gain range: 20 to 27 dB with gain tilt uncontrolled
– Gain and power regulation over/undershoot: 0.5 dB
– Limited maximum output power: 10 dBm
– Maximum output power (with full channel load): 17 dB
– Minimum output power (with one channel): –1 dBm
– Input power (Pin) range at full channel load: –10 to 9 dBm
– Input power (Pin) range at single channel load: –37 to –18 dBm
– Noise figure at G3 20 dB = 7.5 dB
– Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB
– Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB
– Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB
– Optical connectors: LC-UPC/2
– Height: 12.65 in. (332 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (240 mm)
A.5.5 OPT-AMP-L Preamplifier Card Specifications
The OPT-AMP-L card has the following specifications:
– DWDM channel wavelength plan, 100 GHz, 4 skip 1, ITU-T wavelength grid channels 71 (1602.3 nm) to 90 (1570.4 nm)
– DWDM channel wavelength plan, 50 GHz, 8 skip 2, ITU-T wavelength grid channels 70.5 (1602.7 nm) to 90 (1570.4 nm)
– Channel spacing: 100 and 50 GHz
– Total operating wavelength range 1570.0 - 1605.0 nm
– Gain ripple (peak to valley): 1.5 dB
– Standard gain range: 12 to 24 dB
– Extended gain range (uncontrolled gain tilt): 24 to 35 dB
– Gain and power regulation over/undershoot: 0.5 dB
– Minimum output power (with one channel): +2 dBm
– Maximum power output (standard or extended gain range): 20 dB
– Input power range (full channel load): –15 to 8 dB
– Input power range (single channel load): –40 to –17
– Noise figure at G3 20 dB = 8.9 dB
– Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB
– Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB
– Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB
– Optical connectors: LC-UPC/2
– Height: 12.65 in. (332 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (240 mm)
A.5.6 OPT-AMP-17-C Amplifier Card Specifications
The OPT-AMP-17-C card has the following specifications:
– DWDM channel wavelength plan: 80 channels at 50 GHz spacing, 1530.33 nm to 1561.83 nm
– Channel spacing: 50 GHz
– Total operating wavelength range 1529.0 to 1562.5 nm
– Gain ripple (peak to valley): 1.5 dB
– Gain range: 14 to 23 dB
– Optimal gain (gain tilt = 0): 17 dB
– Gain and power regulation over/undershoot: 0.5 dB
– Minimum output power (with one channel): –2 dBm
– Maximum power output (standard or extended gain range): 17.5 dBm
– Input power range (full channel load): –6 to 3 dBm
– Input power range (single channel load): –28 to –19 dBm
– Noise figure at G=17dB = 6 dB maximum
– Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB
– Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB
– Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB
– Optical connectors: LC-UPC/2
– Height: 12.65 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (228.6 mm)
A.5.7 OPT-AMP-C Amplifier Card Specifications
The OPT-AMP-C amplifier card has the following specifications:
– Total operating wavelength range: 1529.0 to 1562.5 nm
– Gain ripple (peak to valley): 1.2 dB
– Gain range: 12 to 24 dB with programmable gain tilt
– Extended gain range: 24 to 35 dB with gain tilt uncontrolled
– Gain and power regulation over/undershoot: 0.5 dB
– Limited maximum output power: 20.5 dBm
– Maximum output power (with full channel load): 20 dBm
– Minimum output power (with one channel): –2 dBm
– Input power (Pin) at full channel load: –15 dBm minimum
– Input power (Pin) range at single channel load: –40 to –17 dBm
– Noise figure at G3 20 dB: 7.6 dB
– Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB
– Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB
– Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB
– Optical connectors: LC-UPC/2
– Height: 12.65 in. (332 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 8.66 in. (220.1 mm)
A.5.8 OPT-RAMP-C Amplifier Card Specifications
The OPT-RAMP-C amplifier card has the following specifications:
– Raman pump 1 wavelength: 1425 nm
– Raman pump 2 wavelength: 1452 nm
– Total Raman Pump power - Line-RX port: 500 mW
– Operating range Raman Pump power - Line-RX port: min 100 mW, max 450 2 mW
– Raman pump laser class: 3B
– Total operating signal wavelength range: 1529 to 1562.5 nm
– EDFA nominal gain value (Line RX to DC-TX): 14 dB
– EDFA gain settable range: 8 to 20 dB
– EDFA Output Power range - DC-TX (Full Channel load): 17.5 3 dBm
– VOA attenuation range: 0 to 25 dB
– Gain and power regulation over/undershoot: 0.5 dB
– EDFA laser class: 1M
– Maximum EDFA output power: 17.5 dBm
– Minimum output power (with one channel): –10 dBm
– Input power (Pin) at full channel load: –3 dBm to +9 dBm
– Input power (Pin) range at single channel load: –24dBm to –10 dBm
– Noise figure at G 14 dB: 7.5 dB
– Insertion loss (Line TX to OSC TX): 0.3 to 2.0 dB
– Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB
– Insertion loss (OSC RX to LINE RX): 0.3 to 1.8 dB
– Optical connectors: LC-UPC/2
– Height: 12.65 in. (332 mm)
– Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
– Depth: 8.665 in. (220.1 mm)
A.5.9 OPT-RAMP-CE Amplifier Card Specifications
The OPT-RAMP-CE amplifier card has the following specifications:
– Raman pump 1 wavelength: 1425 nm
– Raman pump 2 wavelength: 1452 nm
– Total Raman pump power - LINE-RX port: 500 mW
– Operating range Raman pump power - LINE-RX port: min 100 mW, max 450 mW
– Raman pump laser class: 3B
– Total operating signal wavelength range: 1529 to 1562.5 nm
– EDFA nominal gain value (LINE-RX to DC-TX): 11 dB
– EDFA gain settable range: 5 to 17 dB
– EDFA Output power range - DC-TX (Full Channel load): 20.2 dBm
– VOA attenuation range: 0 to 25 dB
– Gain and power regulation over/undershoot: 0.5 dB
– EDFA laser class: 1M
– Maximum EDFA output power: 20.5 dBm
– Minimum output power (with one channel): –10 dBm
– Input power (Pin) at full channel load: 15 dBm (maximum)
– Input power (Pin) range at single channel load: –27dBm (minimum)
– Noise figure at G 11 dB: 7 dB
– Insertion loss (LINE-RX to MON-RX):22 to 26 dB
– Insertion loss (LINE-TX to OSC-TX): 1.5 dB
– Insertion loss (OSC-RX to LINE-RX): 0.7 to 1.7 dB
– Insertion loss (LINE-TX to COM-RX): 0.6 to 1.0 dB
– Insertion loss (LINE-TX to PD12): 1.7dB
– Insertion loss (OSC-RX to LINE-RX): 0.7 to 1.7dB
– Optical connectors: LC-UPC/2
– Height: 13.11 in. (333 mm)
– Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.88 in. (251 mm)
A.8 Reconfigurable Optical Add/Drop Cards
This section provides specifications for the 32DMX, 32DMX-L, 32WSS, 32WSS-L, 40-MUX-C, 40-DMX-C, 40-DMX-CE, 40-WSS-C, 40-WSS-CE, 40-WXC-C, 40-SMR1-C, 40-SMR2-C, and MMU cards.
A.8.1 32DMX Card Specifications
The 32DMX card optical specifications are listed in Table A-6 .
Note For power specifications, see Table A-2.
Table A-6 32DMX Optical Specifications
|
|
|
|
|
|
|
–1 dB bandwidth |
All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation. |
COM RX => TX 1, 32 (OUT) |
+/–110 |
— |
— |
pm |
–3 dB bandwidth |
+/–200 |
— |
— |
pm |
Insertion loss |
All SOP, and within whole operating temperature range, connectors included. |
COM RX => TX 1, 32 |
— |
— |
5.5 |
dB |
VOA dynamic range |
— |
COM RX => TX 1, 32 |
25 |
— |
— |
dB |
Maximum optical input power |
— |
— |
300 |
— |
— |
mW |
The 32DMX channel plan is shown in Table A-7 . All 32DMX client interfaces must comply with this plan.
Table A-7 32DMX Channel Plan
|
|
|
|
|
1 |
1 |
30.3 |
195.9 |
1530.33 |
2 |
31.2 |
195.8 |
1531.12 |
3 |
31.9 |
195.7 |
1531.90 |
4 |
32.6 |
195.6 |
1532.68 |
5 |
2 |
34.2 |
195.4 |
1534.25 |
6 |
35.0 |
195.3 |
1535.04 |
7 |
35.8 |
195.2 |
1535.82 |
8 |
36.6 |
195.1 |
1536.61 |
9 |
3 |
38.1 |
194.9 |
1538.19 |
10 |
38.9 |
194.8 |
1538.98 |
11 |
39.7 |
194.7 |
1539.77 |
12 |
40.5 |
194.6 |
1540.56 |
13 |
4 |
42.1 |
194.4 |
1542.14 |
14 |
42.9 |
194.3 |
1542.94 |
15 |
43.7 |
194.2 |
1543.73 |
16 |
44.5 |
194.1 |
1544.53 |
17 |
5 |
46.1 |
193.9 |
1546.12 |
18 |
46.9 |
193.8 |
1546.92 |
19 |
47.7 |
193.7 |
1547.72 |
20 |
48.5 |
193.6 |
1548.51 |
21 |
6 |
50.1 |
193.4 |
1550.12 |
22 |
50.9 |
193.3 |
1550.92 |
23 |
51.7 |
193.2 |
1551.72 |
24 |
52.5 |
193.1 |
1552.52 |
25 |
7 |
54.1 |
192.9 |
1554.13 |
26 |
54.9 |
192.8 |
1554.94 |
27 |
55.7 |
192.7 |
1555.75 |
28 |
56.5 |
192.6 |
1556.55 |
29 |
8 |
58.1 |
192.4 |
1558.17 |
30 |
58.9 |
192.3 |
1558.98 |
31 |
59.7 |
192.2 |
1559.79 |
32 |
60.6 |
192.1 |
1560.61 |
The 32DMX card has the following additional specifications:
– Height: 12.65 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (228.6 mm)
A.8.2 32DMX-L Card Specifications
The 32DMX-L card optical specifications are listed in Table A-6 .
Note For power specifications, see Table A-2.
Table A-8 32DMX -L Optical Specifications
|
|
|
|
|
|
|
–1 dB bandwidth |
All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation. |
COM RX => TX 1, 32 (OUT) |
+/–100 |
— |
— |
pm |
–3 dB bandwidth |
+/–199 |
— |
— |
pm |
Insertion loss |
All SOP, and within whole operating temperature range, connectors included. |
COM RX => TX 1, 32 |
— |
— |
5.8 |
dB |
VOA dynamic range |
— |
COM RX => TX 1, 32 |
25 |
— |
— |
dB |
Maximum optical input power |
— |
— |
300 |
— |
— |
mW |
The 32DMX-L channel plan is shown in Table A-9 . All 32DMX-L client interfaces must comply with this plan.
Table A-9 32DMX-L Channel Plan
|
|
|
|
B77.8 |
77.8 |
190 |
1577.86 |
78.6 |
189.9 |
1578.69 |
79.5 |
189.8 |
1579.52 |
80.3 |
189.7 |
1580.35 |
B81.1 |
81.1 |
189.6 |
1581.18 |
82.0 |
189.5 |
1582.02 |
82.8 |
189.4 |
1582.85 |
83.6 |
189.3 |
1583.69 |
B84.5 |
84.5 |
189.2 |
1584.53 |
85.3 |
189.1 |
1585.36 |
86.2 |
189 |
1586.20 |
87.0 |
188.9 |
1587.04 |
B87.8 |
87.8 |
188.8 |
1587.88 |
88.7 |
188.7 |
1588.73 |
89.5 |
188.6 |
1589.57 |
90.4 |
188.5 |
1590.41 |
B91.2 |
91.2 |
188.4 |
1591.26 |
92.1 |
188.3 |
1592.10 |
92.9 |
188.2 |
1592.95 |
93.7 |
188.1 |
1593.79 |
B94.6 |
94.6 |
188 |
1594.64 |
95.4 |
187.9 |
1595.49 |
96.3 |
187.8 |
1596.34 |
97.1 |
187.7 |
1597.19 |
B98.0 |
98.0 |
187.6 |
1598.04 |
98.8 |
187.5 |
1598.89 |
99.7 |
187.4 |
1599.75 |
00.6 |
187.3 |
1600.60 |
B01.4 |
01.4 |
187.2 |
1601.46 |
02.3 |
187.1 |
1602.31 |
03.1 |
187 |
1603.17 |
04.0 |
186.9 |
1604.03 |
The 32DMX-L card has the following additional specifications:
– Height: 12.65 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (228.6 mm)
A.8.3 32WSS Card Specifications
The 32WSS card optical specifications are listed in Table A-10 .
Note For power specifications, see Table A-2.
Table A-10 32WSS Optical Specifications
|
|
|
|
|
|
|
–0.25 dB bandwidth |
All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation. |
EXP RX => COM TX |
+/–/95 |
— |
— |
pm |
–0.5 dB bandwidth |
+/–115 |
— |
— |
pm |
–1.0 dB bandwidth |
+/–135 |
— |
— |
pm |
–0.25 dB bandwidth |
Add 1, 32 => COM TX |
+/–115 |
— |
— |
pm |
–0.5 dB bandwidth |
+/–135 |
— |
— |
pm |
–1.0 dB bandwidth |
+/–160 |
— |
— |
pm |
Insertion loss |
All SOP, any optical switch state, and within whole operating temperature range, connectors included. |
EXP RX => COM TX |
— |
— |
11.3 |
dB |
— |
COM RX => EXP TX |
— |
— |
1.5 |
dB |
— |
Add 1, 32 => COM TX |
— |
— |
7.6 |
dB |
— |
COM RX => DROP TX |
6 |
— |
8.5 |
dB |
VOA dynamic range |
— |
EXP RX => COM TX |
20 |
— |
— |
dB |
— |
Add 1, 32 => COM TX |
25 |
— |
— |
dB |
Maximum optical input power |
— |
— |
300 |
— |
— |
mW |
The 32WSS channel plan is shown in Table A-11 . All 32WSS client interfaces must comply with this plan.
Table A-11 32WSS Channel Plan
|
|
|
|
|
1 |
1 |
30.3 |
195.9 |
1530.33 |
2 |
31.2 |
195.8 |
1531.12 |
3 |
31.9 |
195.7 |
1531.90 |
4 |
32.6 |
195.6 |
1532.68 |
5 |
2 |
34.2 |
195.4 |
1534.25 |
6 |
35.0 |
195.3 |
1535.04 |
7 |
35.8 |
195.2 |
1535.82 |
8 |
36.6 |
195.1 |
1536.61 |
9 |
3 |
38.1 |
194.9 |
1538.19 |
10 |
38.9 |
194.8 |
1538.98 |
11 |
39.7 |
194.7 |
1539.77 |
12 |
40.5 |
194.6 |
1540.56 |
13 |
4 |
42.1 |
194.4 |
1542.14 |
14 |
42.9 |
194.3 |
1542.94 |
15 |
43.7 |
194.2 |
1543.73 |
16 |
44.5 |
194.1 |
1544.53 |
17 |
5 |
46.1 |
193.9 |
1546.12 |
18 |
46.9 |
193.8 |
1546.92 |
19 |
47.7 |
193.7 |
1547.72 |
20 |
48.5 |
193.6 |
1548.51 |
21 |
6 |
50.1 |
193.4 |
1550.12 |
22 |
50.9 |
193.3 |
1550.92 |
23 |
51.7 |
193.2 |
1551.72 |
24 |
52.5 |
193.1 |
1552.52 |
25 |
7 |
54.1 |
192.9 |
1554.13 |
26 |
54.9 |
192.8 |
1554.94 |
27 |
55.7 |
192.7 |
1555.75 |
28 |
56.5 |
192.6 |
1556.55 |
29 |
8 |
58.1 |
192.4 |
1558.17 |
30 |
58.9 |
192.3 |
1558.98 |
31 |
59.7 |
192.2 |
1559.79 |
32 |
60.6 |
192.1 |
1560.61 |
The 32WSS card has the following additional specifications:
– Height: 12.65 in. (321.3 mm)
– Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (228.6 mm)
A.8.4 32WSS-L Card Specifications
The 32WSS-L card optical specifications are listed in Table A-12 .
Note For power specifications, see Table A-2.
Table A-12 32WSS-L Optical Specifications
|
|
|
|
|
|
|
–0.1 dB bandwidth |
All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation. |
EXP RX => COM TX |
— |
+/–/57 |
— |
pm |
–0.25 dB bandwidth |
+/–/61 |
+/–/89 |
— |
–0.5 dB bandwidth |
+/–91 |
+/–/116 |
— |
–1.0 dB bandwidth |
+/–135 |
+/–/149 |
— |
–0.1 dB bandwidth |
Add 1, 32 => COM TX |
+/–32 |
+/–/69 |
— |
–0.25 dB bandwidth |
+/–98 |
+/–/129 |
— |
–0.5 dB bandwidth |
+/–135 |
+/–/161 |
— |
–1.0 dB bandwidth |
+/–160 |
+/–/201 |
— |
Insertion loss |
All SOP, any optical switch state, and within whole operating temperature range, connectors included. |
EXP RX => COM TX |
— |
9.7 |
11.3 |
dB |
COM RX => EXP TX |
— |
1.4 |
1.6 |
dB |
Add 1, 32 => COM TX |
— |
6.2 |
8.0 |
dB |
COM RX => DROP TX |
6.0 |
8.0 |
8.5 |
dB |
VOA dynamic range |
— |
EXP RX => COM TX |
20 |
25 |
— |
dB |
— |
Add 1, 32 => COM TX |
25 |
25 |
— |
dB |
Maximum optical input power |
— |
— |
300 |
— |
— |
mW |
The 32WSS-L channel plan is shown in Table A-13 . All 32WSS-L client interfaces must comply with this plan.
Table A-13 32WSS-L Channel Plan
|
|
|
|
B77.8 |
77.8 |
190 |
1577.86 |
78.6 |
189.9 |
1578.69 |
79.5 |
189.8 |
1579.52 |
80.3 |
189.7 |
1580.35 |
B81.1 |
81.1 |
189.6 |
1581.18 |
82.0 |
189.5 |
1582.02 |
82.8 |
189.4 |
1582.85 |
83.6 |
189.3 |
1583.69 |
B84.5 |
84.5 |
189.2 |
1584.53 |
85.3 |
189.1 |
1585.36 |
86.2 |
189 |
1586.20 |
87.0 |
188.9 |
1587.04 |
B87.8 |
87.8 |
188.8 |
1587.88 |
88.7 |
188.7 |
1588.73 |
89.5 |
188.6 |
1589.57 |
90.4 |
188.5 |
1590.41 |
B91.2 |
91.2 |
188.4 |
1591.26 |
92.1 |
188.3 |
1592.10 |
92.9 |
188.2 |
1592.95 |
93.7 |
188.1 |
1593.79 |
B94.6 |
94.6 |
188 |
1594.64 |
95.4 |
187.9 |
1595.49 |
96.3 |
187.8 |
1596.34 |
97.1 |
187.7 |
1597.19 |
B98.0 |
98.0 |
187.6 |
1598.04 |
98.8 |
187.5 |
1598.89 |
99.7 |
187.4 |
1599.75 |
00.6 |
187.3 |
1600.60 |
B01.4 |
01.4 |
187.2 |
1601.46 |
02.3 |
187.1 |
1602.31 |
03.1 |
187 |
1603.17 |
04.0 |
186.9 |
1604.03 |
The 32WSS-L card has the following additional specifications:
– Height: 12.65 in. (321.3 mm)
– Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (228.6 mm)
A.8.5 40-MUX-C Card Specifications
The 40-MUX-C card optical specifications are listed in Table A-14 .
Note For power specifications, see Table A-2.
Table A-14 40-MUX-C Card Optical Specifications
|
|
|
|
|
|
Transmit (Tx) filter shape |
All standard operating procedures (SOP) and within whole operating temperature range |
–1 dB bandwidth, RX 1, 40 => COM TX |
+/–100 |
— |
pm |
–3 dB bandwidth, RX 1, 40 => COM TX |
+/–199 |
— |
pm |
Insertion loss |
All SOP and within whole operating temperature range |
RX 1, 40 => COM TX |
|
5.8 |
dB |
VOA dynamic range |
— |
RX 1, 40 => COM TX |
25 |
— |
dB |
Maximum optical input power |
— |
— |
300 |
— |
mW |
The 40-MUX-C card has the following additional specifications:
– Height: 12.65 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (228.6 mm)
A.8.6 40-DMX-C Card Specifications
The 40-DMX-C card optical specifications are listed in Table A-15 .
Note For power specifications, see Table A-2.
Table A-15 40-DMX-C Card Optical Specifications
|
|
|
|
|
|
Receive (Rx) filter shape |
All SOP and within whole operating temperature range |
–1 dB bandwidth, COM RX => TX 1, 40 (OUT) |
+/–100 |
— |
pm |
–3 dB bandwidth, COM RX => TX 1, 40 (OUT) |
+/–199 |
— |
pm |
Insertion loss |
All SOP and within whole operating temperature range |
COM RX => TX 1, 40 |
— |
5.8 |
dB |
VOA dynamic range |
— |
COM RX => TX 1, 40 |
25 |
— |
dB |
Maximum optical input power |
— |
— |
300 |
— |
mW |
The 40-DMX-C card has the following additional specifications:
– Height: 12.65 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (228.6 mm)
A.8.7 40-DMX-CE Card Specifications
The 40-DMX-CE card optical specifications are listed in Table A-16 .
Note For power specifications, see Table A-2.
Table A-16 40-DMX-CE Card Optical Specifications
|
|
|
|
|
|
Receive (Rx) filter shape |
All SOP and within whole operating temperature range |
–1 dB bandwidth, COM RX => TX 1, 40 (OUT) |
+/–100 |
— |
pm |
–3 dB bandwidth, COM RX => TX 1, 40 (OUT) |
+/–199 |
— |
pm |
Insertion loss |
All SOP and within whole operating temperature range |
COM RX => TX 1, 40 |
— |
5.8 |
dB |
VOA dynamic range |
— |
COM RX => TX 1, 40 |
25 |
— |
dB |
Maximum optical input power |
— |
— |
300 |
— |
mW |
The 40-DMX-CE card has the following additional specifications:
– Height: 12.65 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (228.6 mm)
A.8.8 40-WSS-C Card Specifications
The 40-WSS-C card optical specifications are listed in Table A-17 .
Note For power specifications, see Table A-2.
Table A-17 40-WSS-C Optical Specifications
|
|
|
|
|
|
Channel grid: –0.1 dB |
All SOP and within whole operating temperature range |
EXP_RX to COM_ TX |
— |
— |
pm |
Channel grid: –0.25 dB |
+/– 61 |
— |
pm |
Channel grid: –0.5 dB |
+/– 91 |
— |
pm |
Channel grid: –1.0 dB |
+/– 135 |
— |
pm |
Channel grid: –0.1 dB |
All SOP and within whole operating temperature range |
EXP_RX to COM_ TX |
+/– 32 |
— |
pm |
Channel grid: –0.25 dB |
+/– 98 |
— |
pm |
Channel grid: –0.5 dB |
+/– 135 |
— |
pm |
Channel grid: –1.0 dB |
+/– 160 |
— |
pm |
Insertion loss |
All SOP and within whole operating temperature range |
EXP_RX to COM_ TX |
— |
7.5 |
dB |
EXP_RX to COM_ TX |
— |
2.3 |
dB |
EXP_RX to COM_ TX |
— |
6.0 |
dB |
EXP_RX to COM_ TX |
— |
6.8 |
dB |
VOA dynamic range |
— |
EXP_RX to COM_ TX |
20 |
— |
dB |
EXP_RX to COM_ TX |
25 |
— |
dB |
Maximum optical input power |
— |
— |
300 |
— |
mW |
The 40-WSS-C card channel grid is listed in Table A-18 .
Table A-18 40-WSS-C Channel Grid
|
|
|
|
B30.3 |
30.3 |
195.9 |
1530.33 |
31.1 |
195.8 |
1531.12 |
31.9 |
195.7 |
1531.90 |
32.6 |
195.6 |
1532.68 |
33.4 |
195.5 |
1533.47 |
B34.2 |
34.2 |
195.4 |
1534.25 |
35.0 |
195.3 |
1535.04 |
35.8 |
195.2 |
1535.82 |
36.6 |
195.1 |
1536.61 |
37.4 |
195.0 |
1537.4 |
B38.1 |
38.1 |
194.9 |
1538.19 |
38.9 |
194.8 |
1538.98 |
39.7 |
194.7 |
1539.77 |
40.5 |
194.6 |
1540.56 |
41.3 |
194.5 |
1541.35 |
B42.1 |
42.1 |
194.4 |
1542.14 |
42.9 |
194.3 |
1542.94 |
43.7 |
194.2 |
1543.73 |
44.5 |
194.1 |
1544.53 |
45.3 |
194.0 |
1545.32 |
B46.1 |
46.1 |
193.9 |
1546.12 |
46.9 |
193.8 |
1546.92 |
47.7 |
193.7 |
1547.72 |
48.5 |
193.6 |
1548.51 |
49.3 |
193.5 |
1549.32 |
B50.1 |
50.1 |
193.4 |
1550.12 |
50.9 |
193.3 |
1550.92 |
51.7 |
193.2 |
1551.72 |
52.5 |
193.1 |
1552.52 |
53.3 |
193.0 |
1553.33 |
54.1 |
54.1 |
192.9 |
1544.13 |
54.9 |
192.8 |
1544.94 |
55.7 |
192.7 |
1555.75 |
56.5 |
192.6 |
1556.55 |
57.3 |
192.5 |
1557.36 |
B58.1 |
58.1 |
192.4 |
1558.17 |
58.9 |
192.3 |
1558.98 |
59.7 |
192.2 |
1559.79 |
60.6 |
192.1 |
1560.61 |
61.4 |
192.0 |
1561.42 |
The 40-WSS-C card has the following additional specifications:
– Height: 8.66 in. (220 mm)
– Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
– Depth: 1.42 in. (36 mm)
A.8.9 40-WSS-CE Card Specifications
The 40-WSS-CE card optical specifications are listed in Table A-19 .
Note For power specifications, see Table A-2.
Table A-19 40-WSS-C Card Optical Specifications
|
|
|
|
|
|
Channel grid: –0.1 dB |
All SOP and within whole operating temperature range |
EXP RX greater than or equal to COM TX |
— |
— |
pm |
Channel grid: –0.25 dB |
+/– 61 |
— |
pm |
Channel grid: –0.5 dB |
+/– 91 |
— |
pm |
Channel grid: –1.0 dB |
+/– 135 |
— |
pm |
Channel grid: –0.1 dB |
All SOP and within whole operating temperature range |
Add 1, 40 greater than or equal to COM TX |
+/– 32 |
— |
pm |
Channel grid: –0.25 dB |
+/– 98 |
— |
pm |
Channel grid: –0.5 dB |
+/– 135 |
— |
pm |
Channel grid: –1.0 dB |
+/– 160 |
— |
pm |
Insertion loss |
All SOP and within whole operating temperature range |
EXP RX greater than or equal to COM TX |
— |
7.5 |
dB |
COM RX greater than or equal to EXP TX |
— |
2.3 |
dB |
Add 1, 40 greater than or equal to COM TX |
— |
6.0 |
dB |
COM RX greater than or equal to DROP TX |
— |
6.8 |
dB |
VOA dynamic range |
— |
EXP RX greater than COM TX |
20 |
— |
dB |
Add 1, 40 greater than or equal to COM TX |
25 |
— |
dB |
Maximum optical input power |
— |
— |
300 |
— |
mW |
The 40-WSS-CE card channel grid is listed in Table A-20 .
Table A-20 40-WSS-C Card Channel Grid
|
|
|
|
B30.7 |
30.7 |
195.85 |
1530.72 |
31.5 |
195.75 |
1531.51 |
32.3 |
195.65 |
1532.29 |
33.1 |
195.55 |
1533.07 |
33.9 |
195.45 |
1533.86 |
B34.6 |
34.6 |
195.35 |
1534.64 |
35.4 |
195.25 |
1535.43 |
36.2 |
195.15 |
1536.22 |
37.0 |
195.05 |
1537.00 |
37.8 |
194.95 |
1537.79 |
B38.6 |
38.6 |
194.85 |
1538.58 |
39.4 |
194.75 |
1539.37 |
40.1 |
194.65 |
1540.16 |
40.9 |
194.55 |
1540.95 |
41.8 |
194.45 |
1541.75 |
B42.5 |
42.5 |
194.35 |
1542.54 |
43.3 |
194.25 |
1543.33 |
44.1 |
194.15 |
1544.13 |
44.9 |
194.05 |
1544.92 |
45.7 |
193.95 |
1545.72 |
B46.5 |
46.5 |
193.85 |
1546.52 |
47.3 |
193.75 |
1547.32 |
48.1 |
193.65 |
1548.11 |
48.9 |
193.55 |
1548.91 |
49.7 |
193.45 |
1549.72 |
B50.5 |
50.5 |
193.35 |
1550.52 |
51.3 |
193.25 |
1551.32 |
52.1 |
193.15 |
1552.12 |
52.9 |
193.05 |
1552.93 |
53.7 |
192.95 |
1553.73 |
B54.4 |
54.4 |
192.85 |
1554.54 |
55.3 |
192.75 |
1555.34 |
56.1 |
192.65 |
1556.15 |
56.9 |
192.55 |
1556.96 |
57.8 |
192.45 |
1557.77 |
B58.6 |
58.6 |
192.35 |
1558.58 |
59.4 |
192.25 |
1559.39 |
60.2 |
192.15 |
1560.20 |
61.0 |
192.05 |
1561.01 |
61.8 |
191.95 |
1561.83 |
The 40-WSS-CE card has the following additional specifications:
– Height: 8.66 in. (220 mm)
– Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
– Depth: 1.42 in. (36 mm)
A.8.10 40-WXC-C Card Specifications
The 40-WXC-C card optical specifications are listed in Table A-21 .
Note For power specifications, see Table A-2.
Table A-21 40-WXC-C Optical Specifications
|
|
|
|
|
|
Channel bandwidth: –0.25 dB |
All SOP and within whole operating temperature range |
All paths |
— |
— |
GHz |
Channel bandwidth: –0.5 dB |
+/- 20.5 |
— |
GHz |
Channel bandwidth: –1.5 dB |
— |
— |
GHz |
Channel bandwidth: –03.0 dB |
+/- 37.5 |
— |
GHz |
Insertion loss |
All SOP and within whole operating temperature range |
All paths |
— |
8.5 |
dB |
VOA dynamic range |
— |
All paths |
20 |
— |
dB |
Maximum optical input power |
— |
— |
300 |
— |
mW |
The 40-WXC-C card has the following additional specifications:
– Height: 12.65 in. (321.3 mm) for a standard DWDM unit
– Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (228.6 mm) for a standard DWDM unit
A.8.11 40-SMR1-C Card Specifications
The 40-SMR1-C card optical specifications are listed in Table A-22 .
Note For power specifications, see Table A-2.
Table A-22 40-SMR1-C Optical Specifications
|
|
|
|
|
|
Channel bandwidth: –0.25 dB |
All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation |
All WXC paths (ADD-RX to LINE-TX and EXP-RX to LINE-TX) |
— |
— |
pm |
Channel bandwidth: –0.5 dB |
+/- 160 |
— |
pm |
Channel bandwidth: –1.5 dB |
— |
— |
pm |
Channel bandwidth: –3.0 dB |
+/- 240 |
— |
pm |
Insertion loss |
All SOP, any optical switch state, and within whole operating temperature range, connectors included |
All WXC paths (ADD-RX to LINE-TX and EXP-RX to LINE-TX) |
2.0 |
8.1 |
dB |
All SOP, within whole operating temperature range, connectors included |
DROP-TX with respect to EXP-TX |
— |
5.3 |
dB |
VOA dynamic range |
— |
All WXC paths (ADD-RX to LINE-TX and EXP-RX to LINE-TX) |
20 |
— |
dB |
DROP-TX |
— |
25 |
dB |
Maximum optical input power |
Total power sum of all ports |
— |
500 |
— |
mW |
The EDFA1 amplifier within the 40-SMR1-C card has the following specifications:
- Optical characteristics (specified from LINE-RX to EXP-TX)
– Total operating wavelength range: 1530 to 1561.5 nm
– Gain ripple (peak to valley): 1.2 dB
– Mid-access loss (MAL) range (for dispersion compensation unit [DCU]): 0 to 9 dB
– Gain range: 7 to 38 dB
– Minimum gain (standard range): 7.0 dB
– Maximum gain (standard range with programmable gain tilt): 21 dB
– Maximum gain (extended range with uncontrolled gain tilt): 38 dB
– Gain and power regulation over/undershoot: 0.5 dB
– Maximum output power (with full channel load): 17 dBm
– Minimum output power (with one channel): -5 dBm
– Input power (pin) range at full channel load: -21 to 12 dBm
– Input power (pin) range at single channel load: -43 to -10 dBm
– Noise figure at G = 21 dB = 7.5 dB
The OSC filter within the 40-SMR1-C card has the following specifications:
- OSC filter drop (OSC) insertion loss maximum: 1.8 dB
- OSC filter add (OSC) insertion loss maximum: 1.3 dB
The 40-SMR1-C card has the following additional specifications:
– Height: 13.11 in. (333 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.88 in. (251 mm)
A.8.12 40-SMR2-C Card Specifications
The 40-SMR2-C card optical specifications are listed in Table A-23 .
Note For power specifications, see Table A-2.
Table A-23 40-SMR2-C Optical Specifications
|
|
|
|
|
|
Channel bandwidth: –0.25 dB |
All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation |
All WXC paths (ADD-RX to WXC output, EXP1-RX to WXC output, EXP2-RX to WXC output, and EXP3-RX to WXC output) |
— |
— |
pm |
Channel bandwidth: –0.5 dB |
+/- 160 |
— |
pm |
Channel bandwidth: –1.5 dB |
— |
— |
pm |
Channel bandwidth: –3.0 dB |
+/- 240 |
— |
pm |
Insertion loss |
All SOP, any optical switch state, and within whole operating temperature range, connectors included |
All WXC paths (ADD-RX to WXC output, EXP1-RX to WXC output, EXP2-RX to WXC output, and EXP3-RX to WXC output) |
2.0 |
7 |
dB |
All SOP, within whole operating temperature range, connectors included |
DROP-TX with respect to EXP-TX |
— |
5.3 |
dB |
VOA dynamic range |
— |
All WXC paths (ADD-RX to WXC output, EXP1-RX to WXC output, EXP2-RX to WXC output, and EXP3-RX to WXC output) |
20 |
— |
dB |
DROP-TX |
— |
25 |
dB |
Maximum optical input power |
Total power sum of all ports |
— |
500 |
— |
mW |
The EDFA1 amplifier within the 40-SMR2-C card has the following specifications:
- Optical characteristics (specified from LINE-RX to EXP-TX)
– Total operating wavelength range: 1530 to 1561.5 nm
– Gain ripple (peak to valley): 1.2 dB
– Mid-access loss (MAL) range (for dispersion compensation unit [DCU]): 0 to 9 dB
– Gain range: 7 to 38 dBm in constant gain mode
– Minimum gain (standard range): 7.0 dBm
– Maximum gain (standard range with programmable gain tilt): 21 dBm
– Maximum gain (extended range with uncontrolled gain tilt): 38 dBm
– Gain and power regulation over/undershoot: 0.5 dB
– Maximum output power (with full channel load): 17 dBm
– Minimum output power (with one channel): -5 dBm
– Input power (pin) range at full channel load: -21 to 12 dBm
– Input power (pin) range at single channel load: -43 to -10 dBm
– Noise figure at G= 21 dB = 7.5 dB
The EDFA2 amplifier within the 40-SMR2-C card has the following specifications:
- Optical characteristics (specified from WXC output to LINE-TX)
– Total operating wavelength range 1530.0 to 1561.5 nm
– Gain ripple (peak to valley): 1.2 dB
– Gain range: 13 to 26 dB
– Optimal gain (gain tilt = 0): 17 dB
– Gain and power regulation over/undershoot: 0.5 dB
– Minimum output power (with one channel): -5 dBm
– Input power range (full channel load): -9 to 4 dBm
– Input power range (single channel load): -31 to -18 dBm
– Noise figure at G=17dB = 6 dB maximum
The OSC filter within the 40-SMR2-C card has the following specifications:
- OSC filter drop (OSC) insertion loss maximum: 1.8 dB
- OSC filter add (OSC) insertion loss maximum: 1.3 dB
The 40-SMR2-C card has the following additional specifications:
– Height: 13.11 in. (333 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.88 in. (251 mm)
A.8.13 MMU Card Specifications
The MMU card optical specifications are listed in Table A-24 .
Note For power specifications, see Table A-2.
Table A-24 MMU Optical Specifications
|
|
|
|
|
|
|
Operating bandwidth |
All SOP, any optical switch state, and within whole operating temperature range, connectors included. |
All paths |
1500 |
— |
1605 |
nm |
Insertion loss |
All SOP, any optical switch state, and within whole operating temperature range, connectors included. |
EXP RX => COM TX |
— |
— |
7.0 |
dB |
EXP A RX => COM TX |
— |
— |
2.3 |
dB |
COM RX => EXP TX |
— |
— |
0.8 |
dB |
COM RX => EXP A TX |
— |
— |
14.8 |
dB |
Wavelength dependent losses |
All SOP, any optical switch state, and within whole operating temperature range, connectors included. |
C-band only |
— |
— |
0.3 |
dB |
L-band only |
— |
— |
0.3 |
dB |
C and L bands |
— |
— |
0.5 |
dB |
Polarization dependent loss (PDL) |
— |
C-band only |
— |
— |
0.2 |
dB |
— |
L-band only |
— |
— |
0.2 |
dB |
— |
C and L bands |
— |
— |
0.3 |
dB |
Chromatic dispersion |
|
All paths |
–20 |
— |
+20 |
ps/nm |
Polarization mode dispersion (PMD) |
— |
All paths |
— |
— |
0.1 |
ps |
Optical power reading resolution |
— |
All photodiodes (both real and virtual) |
— |
— |
0.1 |
dB |
Optical power reading precision |
— |
–0.1 |
— |
0.1 |
dB |
Directivity |
All SOP, any optical switch state, and within whole operating temperature range, connectors included. |
EXP RX => EXP A RX |
40 |
— |
— |
dB |
EXP RX => EXP B RX |
40 |
— |
— |
dB |
EXP A RX => EXP B RX |
40 |
— |
— |
dB |
Return loss |
— |
— |
40 |
— |
— |
dB |
Maximum optical input power |
Maximum handling power |
— |
500 |
— |
— |
mW |
The MMU card has the following additional specifications:
– Height: 12.65 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 8.66 in. (220.1 mm)
A.10 Transponder and Muxponder Card Specifications
This section provides specifications for the TXP_MR_10G, MXP_2.5G_10G, TXP_MR_2.5G, TXPP_MR_2.5G, MXP_MR_2.5G, MXPP_MR_2.5G, MXP_2.5G_10E, MXP_2.5G_10E_C, MXP_2.5G_10EX_C, MXP_2.5G_10E, TXP_MR_10E, TXP_MR_10E_C, TXP_MR_10E_L, TXP_MR_10EX_C, MXP_MR_10DME_C, MXP_MR_10DME_L, MXP_MR_10DMEX_C, ADM-10G, and OTU2_XP cards.
For compliance information, refer to the Cisco Optical Transport Products Safety and Compliance Information document.
A.10.1 TXP_MR_10G Card Specifications
The TXP_MR_10G card has the following specifications:
– Bit rate:
9.95328 Gbps for OC-192/STM-64
10.70923 Gbps with ITU-T G.709 Digital Wrapper/forward error correction (FEC)
10.3125 Gbps for 10 Gigabit Ethernet (GE)
11.095 Gbps with ITU-T G.709 Digital Wrapper/FEC over 10 GE
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: 1000 ps/nm
– Loopback modes: Terminal and facility
Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10G card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10G card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10G card.
– Connectors: LC
– Compliance Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.691
– Maximum transmitter output power: +3.5 dBm
– Minimum transmitter output power: +2.5 dBm
– Transmitter: Lithium Niobate (LN) external modulator transmitter
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
- Currently available wavelengths and versions of TXP_MR_10G (16 card versions, each covering two wavelengths):
– 1530.33 to 1531.12 nm (two wavelengths)
– 1531.90 to 1532.68 nm (two wavelengths)
– 1534.25 to 1535.04 nm (two wavelengths)
– 1535.82 to 1536.61 nm (two wavelengths)
– 1538.19 to 1538.98 nm (two wavelengths)
– 1539.77 to 1540.56 nm (two wavelengths)
– 1542.14 to 1542.94 nm (two wavelengths)
– 1543.73 to 1544.53 nm (two wavelengths)
– 1546.12 to 1546.92 nm (two wavelengths)
– 1547.72 to 1548.51 nm (two wavelengths)
– 1550.12 to 1550.92 nm (two wavelengths)
– 1551.72 to 1552.52 nm (two wavelengths)
– 1554.13 to 1554.94 nm (two wavelengths)
– 1555.75 to 1556.55 nm (two wavelengths)
– 1558.17 to 1558.98 nm (two wavelengths)
– 1559.79 to 1560.61 nm (two wavelengths)
– Receiver input power (no FEC, unamplified, 23 dB optical signal-to-noise ratio [OSNR], BER 1 * 10 exp – 12): –8 to –21 dBm
– Receiver input power (no FEC, unamplified, 23 dB OSNR, at +/– 1000 ps/nm BER 1 * 10 exp – 12): –8 to –19 dBm
– Receiver input power (no FEC, amplified, 19 dB OSNR, BER 1 * 10 exp – 12): –8 to –20 dBm
– Receiver input power (no FEC, amplified, 19 dB OSNR, at +/– 1000 ps/nm BER 1 * 10 exp – 12):–8 to –18 dBm
– Receiver input power (FEC, unamplified, 23 dB OSNR, BER 8 * 10 exp – 5): –8 to –24 dBm
– Receiver input power (FEC, unamplified, 23 dB OSNR, at +/– 1000 ps/nm, BER 8 * 10 exp – 5): –8 to –22 dBm
– Receiver input power (FEC, amplified, 9 dB OSNR, BER 8 * 10 exp – 5): –8 to –18 dBm
– Receiver input power (FEC, unamplified, 11 dB OSNR, at +/– 800 ps/nm, BER 8 * 10 exp – 5): –8 to –18 dBm
– Bit rate: 9.95328 Gbps or 10.3125 Gbps
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: Compliant with SR-1 specification for OC-192. In the case of 10 GE, the allowance is up to 10 km of single-mode fiber (SMF) dispersion.
– Loopback modes: Terminal and facility
– Connectors: LC
- Transmitter (client side)
– Maximum transmitter output power: –1 dBm
– Minimum transmitter output power: –6 dBm
– Center wavelength: 1290 to 1330 nm
– Nominal wavelength: 1310 nm
– Transmitter: Distributed feedback (DFB) laser
– Maximum receiver level: –1 dBm at BER 1 * 10 exp – 12
– Minimum receiver level: –14 dBm at BER 1 * 10 exp – 12
– Receiver: avalanche photodiode (APD)
– Link loss budget: 8 dB minimum, at BER = 1 * 10 exp – 12
– Receiver input wavelength range: 1290 to 1605 nm
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.2 MXP_2.5G_10G Card Specifications
The MXP_2.5G_10G card has the following specifications:
– Bit rate:
9.95328 Gbps for OC-192/STM-64
10.70923 Gbps with ITU-T G.709 Digital Wrapper/FEC
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: 1000 ps/nm
– Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10G card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10G card. Using direct fiber loopbacks causes irreparable damage to the MXP_2.5G_10G card.
– Connectors: LC
– Maximum transmitter output power: +3.5 dBm
– Minimum transmitter output power: +2.5 dBm
– Transmitter: LN external modulator transmitter
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
- Currently available wavelengths and versions of MXP_2.5G_10G (16 card versions, each covering two wavelengths):
– 1530.33 to 1531.12 nm (two wavelengths)
– 1531.90 to 1532.68 nm (two wavelengths)
– 1534.25 to 1535.04 nm (two wavelengths)
– 1535.82 to 1536.61 nm (two wavelengths)
– 1538.19 to 1538.98 nm (two wavelengths)
– 1539.77 to 1540.56 nm (two wavelengths)
– 1542.14 to 1542.94 nm (two wavelengths)
– 1543.73 to 1544.53 nm (two wavelengths)
– 1546.12 to 1546.92 nm (two wavelengths)
– 1547.72 to 1548.51 nm (two wavelengths)
– 1550.12 to 1550.92 nm (two wavelengths)
– 1551.72 to 1552.52 nm (two wavelengths)
– 1554.13 to 1554.94 nm (two wavelengths)
– 1555.75 to 1556.55 nm (two wavelengths)
– 1558.17 to 1558.98 nm (two wavelengths)
– 1559.79 to 1560.61 nm (two wavelengths)
– Receiver input power (no FEC, unamplified, 23 dB OSNR, BER 1 * 10 exp – 12): –8 to –21 dBm
– Receiver input power (no FEC, unamplified, 23 dB OSNR, at +/– 1000 ps/nm BER 1 * 10 exp – 12): –8 to –19 dBm
– Receiver input power (no FEC, amplified, 19 dB OSNR, BER 1 * 10 exp – 12): –8 to –20 dBm
– Receiver input power (no FEC, amplified, 19 dB OSNR, at +/– 1000 ps/nm BER 1 * 10 exp – 12): –8 to –18 dBm
– Receiver input power (FEC, unamplified, 23 dB OSNR, BER 8 * 10 exp – 5): –8 to –24 dBm
– Receiver input power (FEC, unamplified, 23 dB OSNR, at +/– 1000 ps/nm, BER 8 * 10 exp – 5): –8 to –22 dBm
– Receiver input power (FEC, amplified, 9 dB OSNR, BER 8 * 10 exp – 5): –8 to –18 dBm
– Receiver input power (FEC, unamplified, 11 dB OSNR, at +/– 800 ps/nm, BER 8 * 10 exp – 5): –8 to –18 dBm
– Bit rate: 2.48832 Gbps
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: Compliant with SR-1 specification for OC-192. In the case of 10 GE, allowance is up to 10 km of SMF fiber of dispersion.
– Loopback modes: Terminal and facility
– Connectors: LC
- Transmitter (client side): Depends on the Small Form-factor Pluggable (SFP) that is used.
- Receiver (client side): Depends on the SFP that is used.
- Dimensions
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.3 TXP_MR_2.5G and TXPP_MR_2.5G Card Specifications
The TXP_MR_2.5G and TXPP_MR_2.5G cards have the following specifications:
– Bit rate:
2.488 Gbps for OC-48/STM-16
2.66 Gbps with ITU-T G.709 Digital Wrapper/FEC
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: 5400 ps/nm
– Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the TXP_MR_2.5G and TXPP_MR_2.5G cards in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_2.5G and TXPP_MR_2.5G cards. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_2.5G and TXPP_MR_2.5G cards.
– Connectors: LC
– Maximum transmitter output power: +1 dBm
– Minimum transmitter output power: –4.5 dBm
– Transmitter: Direct modulated laser
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
- Currently available wavelengths of TXP_MR_2.5G and TXPP_MR_2.5G (eight card versions):
ITU grid blue band: 1530.334 to 1544.526 nm (four card versions covering four wavelengths each)
ITU grid red band: 1546.119 to 1560.606 nm (four card versions covering four wavelengths each)
Table A-34 TXP_MR_2.5G/TXPP_MR_2.5G Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
22 dB |
Off - 2R |
< 10 exp – 12 |
N/A |
– 9 to – 24 dBm |
— |
22 dB |
Off - 2R |
< 10 exp – 12 |
N/A |
– 9 to – 21 dBm |
+/– 3300ps/nm |
21 dB |
Off - 3R |
< 10 exp – 12 |
N/A |
– 9 to – 30 dBm |
— |
22 dB |
Off - 3R |
< 10 exp – 12 |
N/A |
– 9 to – 30 dBm |
+/– 1800ps/nm |
23 dB |
Off - 3R |
< 10 exp – 12 |
N/A |
– 9 to – 30 dBm |
+/– 5400ps/nm |
12 dB |
Standard- 3R |
< 10 exp – 5 |
< 10 exp – 15 |
– 9 to – 25 dBm |
— |
12 dB |
Standard- 3R |
< 10 exp – 5 |
< 10 exp – 15 |
– 9 to – 24 dBm |
+/– 1800ps/nm |
12 dB |
Standard- 3R |
< 10 exp – 5 |
< 10 exp – 15 |
– 9 to – 23 dBm |
+/– 5400ps/nm |
21 dB |
Standard- 3R |
< 10 exp – 5 |
< 10 exp – 15 |
– 9 to – 31 dBm |
— |
– Receiver: APD
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
– Bit rate: 8 Mbps to 2.488 Gbps
– Code: Scrambled NRZ
– Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
– Maximum chromatic dispersion allowance: Based on SFP
– Loopback modes: Terminal and facility
– Connectors: LC
- Transmitter (client side)
– Maximum transmitter output power: –1 dBm
– Minimum transmitter output power: –6 dBm
– Center wavelength: Based on SFP
– Nominal wavelength: Based on SFP
– Transmitter: Based on SFP
– Maximum receiver level: –1 dBm at BER 1 * 10 exp – 12
– Minimum receiver level: –14 dBm at BER 1 * 10 exp – 12
– Receiver: APD
– Link loss budget: 8 dB minimum, at BER = 1 * 10 exp – 12
– Receiver input wavelength range: 850nm to 1605 nm
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.4 MXP_MR_2.5G and MXPP_MR_2.5G Card Specifications
The MXP_MR_2.5G and MXPP_MR_2.5G cards have the following specifications:
– FC1G—Fibre Channel 1.06 Gbps
– FC2G—Fibre Channel 2.125 Gbps
– FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)
– FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)
– ESCON—Enterprise System Connection 200 Mbps
– ONE_GE—One Gigabit Ethernet 1.125 Gbps
– Mixed configurations up to maximum line rate of 2.5 Gbps (for example, if you have a port configured for FC2G, you cannot use another port at the same time). See the “MXP_MR_2.5G and MXPP_MR_2.5G Cards” section for more information on mixed-mode operation.
- Client ports: 8x SFP
- Performance monitoring (PM) for all interfaces
- Buffer-to-buffer credit management for distance extension
- Line (trunk side)
– Bit rate: 2.488 Gbps for OC-48/STM-16
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: 6000 ps/nm
– Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_2.5G and MXPP_MR_2.5G cards in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_2.5G and MXPP_MR_2.5G cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_2.5G and MXPP_MR_2.5G cards.
– Connectors: LC
– Transmit power: +3 +/– 1 dBm with MXP_MR_2.5G card, and +/– 1 dBm with MXPP_MR_2.5G card
– 50-GHz DWDM migration ready (the wavelength deviation is less than +/– 0.040 nm through wavelocker deployment)
– Four-channel wavelength tunability at 100-GHz spacing
– Transmitter maximum return reflectance: –27 dB
– Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB
– Minimum side mode suppression ratio: 30 dB
– Transmitter is a direct modulated laser
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
- Currently available wavelengths of the TXP_MR_2.5G and TXPP_MR_2.5G cards (eight card versions):
– ITU grid blue band: 1530.334 to 1544.526 nm (four card versions, four wavelengths each)
– ITU grid red band: 1546.119 to 1560.606 nm (four card versions, four wavelengths each)
Table A-35 MXP_MR_2.5G/MXPP_MR_2.5G Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
17 dB |
N/A |
< 10 exp – 12 |
N/A |
– 9 to – 23 dBm |
— |
17 dB |
N/A |
< 10 exp – 12 |
N/A |
– 9 to – 22 dBm |
+/– 1800 ps/nm |
17 dB |
N/A |
< 10 exp – 12 |
N/A |
– 9 to – 21 dBm |
+/– 5400 ps/nm |
18 dB |
N/A |
< 10 exp – 12 |
N/A |
– 9 to – 23 dBm |
+/– 1800 ps/nm |
19 dB |
N/A |
< 10 exp – 12 |
N/A |
– 9 to – 23 dBm |
+/– 5400 ps/nm |
21 dB |
N/A |
< 10 exp – 12 |
N/A |
– 9 to – 30 dBm |
— |
21 dB |
N/A |
< 10 exp – 12 |
N/A |
– 9 to – 29 dBm |
+/– 1800 ps/nm |
21 dB |
N/A |
< 10 exp – 12 |
N/A |
– 9 to – 28 dBm |
+/– 5400 ps/nm |
22 dB |
N/A |
< 10 exp – 12 |
N/A |
– 9 to – 30 dBm |
+/– 1800 ps/nm |
23 dB |
N/A |
< 10 exp – 12 |
N/A |
– 9 to – 30 dBm |
+/– 5400 ps/nm |
– Receiver sensitivity –28 dBm, BER 1 * 10 exp – 12
– Receiver overload is equal to or exceeds –8 dBm
– Receiver maximum reflectance of –27 dB
– Bit rate: 200Mbps or 1.06 Gbps to 2.125 Gbps per client
– Code: Scrambled NRZ
– Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
– Loopback modes: Terminal and facility
– Connectors: LC
- Transmitter (client side)
– Maximum transmitter output power: –1 dBm
– Minimum transmitter output power: –6 dBm
– Center wavelength: Based on SFP
– Nominal wavelength: Based on SFP
– Transmitter: Based on SFP
– Maximum receiver level: –1 dBm at BER 1 * 10 exp – 12
– Minimum receiver level: –14 dBm at BER 1 * 10 exp – 12
– Receiver: APD
– Link loss budget: 8 dB minimum, at BER = 1 * 10 exp – 12
– Receiver input wavelength range: 1290 to 1605 nm or 850nm
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 2.25 lb (1.02 kg)
A.10.5 MXP_2.5G_10E Card Specifications
The MXP_2.5G_10E card has the following specifications:
– Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: +/– 1200 ps/nm (specified penalty)
– Loopback modes: Terminal and facility
Caution
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10E card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10E card. Using direct fiber loopbacks causes irreparable damage to the MXP_2.5G_10E card.
– Connectors: LC
– Maximum transmitter output power: +6 dBm
– Minimum transmitter output power: +3 dBm
– Transmitter: LN external modulator transmitter
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
- Currently available wavelengths and versions of MXP_2.5G_10E (eight card versions):
ITU grid blue band:
– 1530.33 to 1533.07 nm (four channels)
– 1534.25 to 1537.00 nm (four channels)
– 1538.19 to 1540.95 nm (four channels)
– 1542.14 to 1544.92 nm (four channels)
ITU grid red band:
– 1546.12 to 1548.92 nm (four channels)
– 1550.12 to 1552.93 nm (four channels)
– 1554.13 to 1556.96 nm (four channels)
– 1558.17 to 1561.01 nm (four channels)
– Receiver: APD
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
Table A-36 MXP_2.5G_10E Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
30 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 20 dBm |
+/– 1200 ps/nm |
26 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 20 dBm |
+/– 1000 ps/nm |
26 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 22 dBm |
— |
17 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 18 dBm |
+/– 800 ps/nm |
15 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 18 dBm |
— |
15 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 18 dBm |
+/– 800 ps/nm |
14 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 18 dBm |
— |
– Bit rate: 2.5 Gbps per port (OC-48/STM-16)
– Code: Scrambled NRZ
– Fiber: 1310-nm single-mode
– Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
– Loopback modes: Terminal and facility
– Connectors: LC (optical)
- Transmitter (client side): Depends on the SFP that is used.
- Receiver (client side): Depends on the SFP that is used.
- Dimensions
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.6 MXP_2.5G_10E_C Card Specifications
The MXP_2.5G_10E_C card has the following specifications:
– Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: +/– 1200 ps/nm (specified penalty)
– Loopback modes: Terminal and facility
Caution
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10E_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10E_C card. Using direct fiber loopbacks causes irreparable damage to the card.
– Connectors: LC
– Maximum transmitter output power: +6 dBm
– Minimum transmitter output power: +3 dBm
– Transmitter: LN external modulator transmitter
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
- Currently available wavelengths and versions of MXP_2.5G_10E_C card:
There is a single version of the MXP_2.5G_10E_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-37 .
Table A-37 MXP_2.5G_10E_C Card Trunk Wavelengths
|
|
|
|
|
|
1 |
196.00 |
1529.55 |
42 |
193.95 |
1545.72 |
2 |
195.95 |
1529.94 |
43 |
193.90 |
1546.119 |
3 |
195.90 |
1530.334 |
44 |
193.85 |
1546.518 |
4 |
195.85 |
1530.725 |
45 |
193.80 |
1546.917 |
5 |
195.80 |
1531.116 |
46 |
193.75 |
1547.316 |
6 |
195.75 |
1531.507 |
47 |
193.70 |
1547.715 |
7 |
195.70 |
1531.898 |
48 |
193.65 |
1548.115 |
8 |
195.65 |
1532.290 |
49 |
193.60 |
1548.515 |
9 |
195.60 |
1532.681 |
50 |
193.55 |
1548.915 |
10 |
195.55 |
1533.073 |
51 |
193.50 |
1549.32 |
11 |
195.50 |
1533.47 |
52 |
193.45 |
1549.71 |
12 |
195.45 |
1533.86 |
53 |
193.40 |
1550.116 |
13 |
195.40 |
1534.250 |
54 |
193.35 |
1550.517 |
14 |
195.35 |
1534.643 |
55 |
193.30 |
1550.918 |
15 |
195.30 |
1535.036 |
56 |
193.25 |
1551.319 |
16 |
195.25 |
1535.429 |
57 |
193.20 |
1551.721 |
17 |
195.20 |
1535.822 |
58 |
193.15 |
1552.122 |
18 |
195.15 |
1536.216 |
59 |
193.10 |
1552.524 |
19 |
195.10 |
1536.609 |
60 |
193.05 |
1552.926 |
20 |
195.05 |
1537.003 |
61 |
193.00 |
1553.33 |
21 |
195.00 |
1537.40 |
62 |
192.95 |
1553.73 |
22 |
194.95 |
1537.79 |
63 |
192.90 |
1554.134 |
23 |
194.90 |
1538.186 |
64 |
192.85 |
1554.537 |
24 |
194.85 |
1538.581 |
65 |
192.80 |
1554.940 |
25 |
194.80 |
1538.976 |
66 |
192.75 |
1555.343 |
26 |
194.75 |
1539.371 |
67 |
192.70 |
1555.747 |
27 |
194.70 |
1539.766 |
68 |
192.65 |
1556.151 |
28 |
194.65 |
1540.162 |
69 |
192.60 |
1556.555 |
29 |
194.60 |
1540.557 |
70 |
192.55 |
1556.959 |
30 |
194.55 |
1540.953 |
71 |
192.50 |
1557.36 |
31 |
194.50 |
1541.35 |
72 |
192.45 |
1557.77 |
32 |
194.45 |
1541.75 |
73 |
192.40 |
1558.173 |
33 |
194.40 |
1542.142 |
74 |
192.35 |
1558.578 |
34 |
194.35 |
1542.539 |
75 |
192.30 |
1558.983 |
35 |
194.30 |
1542.936 |
76 |
192.25 |
1559.389 |
36 |
194.25 |
1543.333 |
77 |
192.20 |
1559.794 |
37 |
194.20 |
1543.730 |
78 |
192.15 |
1560.200 |
38 |
194.15 |
1544.128 |
79 |
192.10 |
1560.606 |
39 |
194.10 |
1544.526 |
80 |
192.05 |
1561.013 |
40 |
194.05 |
1544.924 |
81 |
192.00 |
1561.42 |
41 |
194.00 |
1545.32 |
82 |
191.95 |
1561.83 |
Table A-38 MXP_2.5G_10E_C Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
30 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 18 dBm |
+/– 1200 ps/nm |
26 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 18 dBm |
+/– 1000 ps/nm |
26 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 18 dBm |
— |
17 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 18 dBm |
+/– 800 ps/nm |
15.5 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 18 dBm |
— |
14 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 18 dBm |
+/– 800 ps/nm |
12 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 18 dBm |
— |
– Receiver: APD
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
– Receiver input wavelength range: 1529 to 1562 nm
– Bit rate: 2.5 Gbps per port (OC-48/STM-16)
– Code: Scrambled NRZ
– Fiber: 1310-nm single-mode
– Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
– Loopback modes: Terminal and facility
– Connectors: LC (optical)
- Transmitter (client side): Depends on the SFP that is used.
- Receiver (client side): Depends on the SFP that is used.
- Dimensions
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.7 MXP_2.5G_10E_L Card Specifications
The MXP_2.5G_10E_L card has the following specifications:
– Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: +/– 1200 ps/nm (specified penalty)
– Loopback modes: Terminal and facility
Caution
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10E_L card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10E_L card. Using direct fiber loopbacks causes irreparable damage to the card.
– Connectors: LC
– Maximum transmitter output power: +6 dBm
– Minimum transmitter output power: +3 dBm
– Transmitter: LN external modulator transmitter
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
- Currently available wavelengths and versions of MXP_2.5G_10E_L card:
There is a single version of the MXP_2.5G_10E_L card. It is tunable across 80 wavelengths in the L band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-39 .
Table A-39 MXP_2.5G_10E_L Card Trunk Wavelengths
|
|
|
|
|
|
1 |
190.85 |
1570.83 |
41 |
188.85 |
1587.46 |
2 |
190.8 |
1571.24 |
42 |
188.8 |
1587.88 |
3 |
190.75 |
1571.65 |
43 |
188.75 |
1588.30 |
4 |
190.7 |
1572.06 |
44 |
188.7 |
1588.73 |
5 |
190.65 |
1572.48 |
45 |
188.65 |
1589.15 |
6 |
190.6 |
1572.89 |
46 |
188.6 |
1589.57 |
7 |
190.55 |
1573.30 |
47 |
188.55 |
1589.99 |
8 |
190.5 |
1573.71 |
48 |
188.5 |
1590.41 |
9 |
190.45 |
1574.13 |
49 |
188.45 |
1590.83 |
10 |
190.4 |
1574.54 |
50 |
188.4 |
1591.26 |
11 |
190.35 |
1574.95 |
51 |
188.35 |
1591.68 |
12 |
190.3 |
1575.37 |
52 |
188.3 |
1592.10 |
13 |
190.25 |
1575.78 |
53 |
188.25 |
1592.52 |
14 |
190.2 |
1576.20 |
54 |
188.2 |
1592.95 |
15 |
190.15 |
1576.61 |
55 |
188.15 |
1593.37 |
16 |
190.1 |
1577.03 |
56 |
188.1 |
1593.79 |
17 |
190.05 |
1577.44 |
57 |
188.05 |
1594.22 |
18 |
190 |
1577.86 |
58 |
188 |
1594.64 |
19 |
189.95 |
1578.27 |
59 |
187.95 |
1595.06 |
20 |
189.9 |
1578.69 |
60 |
187.9 |
1595.49 |
21 |
189.85 |
1579.10 |
61 |
187.85 |
1595.91 |
22 |
189.8 |
1579.52 |
62 |
187.8 |
1596.34 |
23 |
189.75 |
1579.93 |
63 |
187.75 |
1596.76 |
24 |
189.7 |
1580.35 |
64 |
187.7 |
1597.19 |
25 |
189.65 |
1580.77 |
65 |
187.65 |
1597.62 |
26 |
189.6 |
1581.18 |
66 |
187.6 |
1598.04 |
27 |
189.55 |
1581.60 |
67 |
187.55 |
1598.47 |
28 |
189.5 |
1582.02 |
68 |
187.5 |
1598.89 |
29 |
189.45 |
1582.44 |
69 |
187.45 |
1599.32 |
30 |
189.4 |
1582.85 |
70 |
187.4 |
1599.75 |
31 |
189.35 |
1583.27 |
71 |
187.35 |
1600.17 |
32 |
189.3 |
1583.69 |
72 |
187.3 |
1600.60 |
33 |
189.25 |
1584.11 |
73 |
187.25 |
1601.03 |
34 |
189.2 |
1584.53 |
74 |
187.2 |
1601.46 |
35 |
189.15 |
1584.95 |
75 |
187.15 |
1601.88 |
36 |
189.1 |
1585.36 |
76 |
187.1 |
1602.31 |
37 |
189.05 |
1585.78 |
77 |
187.05 |
1602.74 |
38 |
189 |
1586.20 |
78 |
187 |
1603.17 |
39 |
188.95 |
1586.62 |
79 |
186.95 |
1603.60 |
40 |
188.9 |
1587.04 |
80 |
186.9 |
1604.03 |
Table A-40 MXP_2.5G_10E_L Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
30 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 20 dBm |
+/– 1200 ps/nm |
26 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 20 dBm |
+/– 1000 ps/nm |
26 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 22 dBm |
— |
17 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 18 dBm |
+/– 800 ps/nm |
15.5 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 18 dBm |
— |
15 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 18 dBm |
+/– 800 ps/nm |
13 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 18 dBm |
— |
– Receiver: APD
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
– Receiver input wavelength range: 1570 to 1604 nm
– Bit rate: 2.5 Gbps per port (OC-48/STM-16)
– Code: Scrambled NRZ
– Fiber: 1310-nm single-mode
– Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
– Loopback modes: Terminal and facility
– Connectors: LC (optical)
- Transmitter (client side): Depends on the SFP that is used.
- Receiver (client side): Depends on the SFP that is used.
- Dimensions
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.8 MXP_2.5G_10EX_C Card Specifications
The MXP_2.5G_10EX_C card has the following specifications:
– Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: +/– 1600 ps/nm (specified penalty)
– Loopback modes: Terminal and facility
Caution
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10EX_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10EX_C card. Using direct fiber loopbacks causes irreparable damage to the card.
– Connectors: LC
– Maximum transmitter output power: +6 dBm
– Minimum transmitter output power: +3 dBm
– Transmitter: LN external modulator transmitter
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
- Currently available wavelengths and versions of MXP_2.5G_10EX_C card:
There is a single version of the MXP_2.5G_10EX_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-37 .
Table A-41 MXP_2.5G_10EX_C Card Trunk Wavelengths
|
|
|
|
|
|
1 |
196.00 |
1529.55 |
42 |
193.95 |
1545.72 |
2 |
195.95 |
1529.94 |
43 |
193.90 |
1546.12 |
3 |
195.90 |
1530.334 |
44 |
193.85 |
1546.52 |
4 |
195.85 |
1530.725 |
45 |
193.80 |
1546.92 |
5 |
195.80 |
1531.116 |
46 |
193.75 |
1547.32 |
6 |
195.75 |
1531.507 |
47 |
193.70 |
1547.72 |
7 |
195.70 |
1531.898 |
48 |
193.65 |
1548.11 |
8 |
195.65 |
1532.290 |
49 |
193.60 |
1548.51 |
9 |
195.60 |
1532.681 |
50 |
193.55 |
1548.91 |
10 |
195.55 |
1533.073 |
51 |
193.50 |
1549.32 |
11 |
195.50 |
1533.47 |
52 |
193.45 |
1549.72 |
12 |
195.45 |
1533.86 |
53 |
193.40 |
1550.12 |
13 |
195.40 |
1534.250 |
54 |
193.35 |
1550.52 |
14 |
195.35 |
1534.643 |
55 |
193.30 |
1550.92 |
15 |
195.30 |
1535.036 |
56 |
193.25 |
1551.32 |
16 |
195.25 |
1535.429 |
57 |
193.20 |
1551.72 |
17 |
195.20 |
1535.822 |
58 |
193.15 |
1552.12 |
18 |
195.15 |
1536.216 |
59 |
193.10 |
1552.52 |
19 |
195.10 |
1536.609 |
60 |
193.05 |
1552.93 |
20 |
195.05 |
1537.003 |
61 |
193.00 |
1553.33 |
21 |
195.00 |
1537.40 |
62 |
192.95 |
1553.73 |
22 |
194.95 |
1537.79 |
63 |
192.90 |
1554.13 |
23 |
194.90 |
1538.186 |
64 |
192.85 |
1554.54 |
24 |
194.85 |
1538.581 |
65 |
192.80 |
1554.94 |
25 |
194.80 |
1538.976 |
66 |
192.75 |
1555.34 |
26 |
194.75 |
1539.371 |
67 |
192.70 |
1555.75 |
27 |
194.70 |
1539.766 |
68 |
192.65 |
1556.15 |
28 |
194.65 |
1540.162 |
69 |
192.60 |
1556.55 |
29 |
194.60 |
1540.557 |
70 |
192.55 |
1556.96 |
30 |
194.55 |
1540.953 |
71 |
192.50 |
1557.36 |
31 |
194.50 |
1541.35 |
72 |
192.45 |
1557.77 |
32 |
194.45 |
1541.75 |
73 |
192.40 |
1558.17 |
33 |
194.40 |
1542.142 |
74 |
192.35 |
1558.58 |
34 |
194.35 |
1542.539 |
75 |
192.30 |
1558.98 |
35 |
194.30 |
1542.936 |
76 |
192.25 |
1559.39 |
36 |
194.25 |
1543.333 |
77 |
192.20 |
1559.79 |
37 |
194.20 |
1543.730 |
78 |
192.15 |
1560.20 |
38 |
194.15 |
1544.128 |
79 |
192.10 |
1560.61 |
39 |
194.10 |
1544.526 |
80 |
192.05 |
1561.01 |
40 |
194.05 |
1544.924 |
81 |
192.00 |
1561.42 |
41 |
194.00 |
1545.32 |
82 |
191.95 |
1561.83 |
Table A-42 TMXP_2.5G_10EX_C Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
|
16 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 20 dBm |
+/– 1600 ps/nm |
— |
15 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 20 dBm |
— |
— |
TBD |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 20 dBm |
— |
|
12.5 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 20 dBm |
— |
— |
17 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 20 dBm |
+/- 4000 ps/nm |
— |
15.2 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 20 dBm |
+/- 2500 ps/nm |
— |
17.4 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 20 dBm |
|
3 |
– Receiver: APD
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
– Receiver input wavelength range: 1529 to 1562 nm
– Bit rate: 2.5 Gbps per port (OC-48/STM-16)
– Code: Scrambled NRZ
– Fiber: 1310-nm single-mode
– Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
– Loopback modes: Terminal and facility
– Connectors: LC (optical)
- Transmitter (client side): Depends on the SFP that is used.
- Receiver (client side): Depends on the SFP that is used.
- Dimensions
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.9 MXP_MR_10DME_C Card Specifications
The MXP_MR_10DME_C card has the following specifications:
– FC1G—Fibre Channel 1.06 Gbps
– FC2G—Fibre Channel 2.125 Gbps
– FC4G—Fibre Channel 4.25 Gbps
– FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)
– FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)
– FICON4G—Fiber connectivity 4.25 Gbps (IBM signal)
– ISC compatibility
– ISC peer 1G
– ISC peer 2G
– ONE_GE—One Gigabit Ethernet 1.125 Gbps
– Mixed configurations up to maximum line rate of 10.0 Gbps. See the “MXP_MR_10DME_C and MXP_MR_10DME_L Cards” section for more information on mixed-mode operation.
- Client ports: 8x SFP
- Line (trunk side)
– Bit rate: 9.952 Gbps for OC-192/STM-64
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_10DME_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_10DME_C cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_10DME_C cards.
– Connectors: LC
– Minimum output power: +3 dBm
– Maximum output power: +6 dBm
– Minimum Single-Mode Suppression Ratio (SMSR): 30 dB
– Minimum optical extinction ratio: 10 dB
– 41 wavelength tunability at 100-GHz spacing
– Receiver maximum return reflectance (Rx return loss): –27 dB
– Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB
– Minimum side mode suppression ratio: 30 dB
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
– For available wavelengths for the MXP_MR_10DME_C card, see Table 10-29.
Table A-43 MXP_MR_10DME_C Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
|
|
None |
23 dB |
< 10 exp – 12 |
— |
–8 to –20 dBm |
+/– 1200 ps/nm |
2 dBm |
— |
19 dB |
< 10 exp – 12 |
— |
–9 to –22 dBm |
+/– 1000 ps/nm |
2 dBm |
— |
FEC |
10 dB |
< 10 exp – 5 |
< 10 exp – 15 |
–8 to –18 dBm |
+/– 800 ps/nm |
— |
1.5 dB |
Enhanced FEC |
19 dB |
< 10 exp – 4 |
< 10 exp – 15 |
–8 to –26 dBm |
+/– 800 ps/nm |
2 dBm |
2 dB |
8 dB |
< 10 exp – 4 |
< 10 exp – 15 |
–8 to –18 dBm |
+/– 800 ps/nm |
2 dBm |
1.5 dB |
– Receiver: APD
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
– Receiver input wavelength range: 1529 to 1562 nm
– Bit rate: 1.06 Gbps to 4.25 Gbps per client
– Code: Scrambled NRZ
– Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
– Maximum chromatic dispersion allowance: Based on SFP
– Loopback modes: Terminal and facility
– Connectors: LC
- Transmitter (client side)
– Maximum transmitter output power: –1 dBm
– Minimum transmitter output power: –6 dBm
– Center wavelength: Based on SFP
– Nominal wavelength: Based on SFP
– Transmitter: Based on SFP
– Maximum receiver level: –1 dBm at BER 1 * 10 exp – 12
– Minimum receiver level: –14 dBm at BER 1 * 10 exp – 12
– Receiver: APD
– Link loss budget: 8 dB minimum, at BER = 1 * 10 exp – 12
– Receiver input wavelength range: 1290 to 1605 nm or 850nm
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 2.25 lb (1.02 kg)
A.10.10 MXP_MR_10DME_L Card Specifications
The MXP_MR_10DME_L card has the following specifications:
– FC1G—Fibre Channel 1.06 Gbps
– FC2G—Fibre Channel 2.125 Gbps
– FC4G—Fibre Channel 4.25 Gbps
– FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)
– FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)
– FICON4G—Fiber connectivity 4.25 Gbps (IBM signal)
– ISC compatibility
– ISC peer 1G
– ISC peer 2G
– ONE_GE—One Gigabit Ethernet 1.125 Gbps
– Mixed configurations up to maximum line rate of 10.0 Gbps. See the “MXP_MR_10DME_C and MXP_MR_10DME_L Cards” section for more information on mixed-mode operation.
- Client ports: 8x SFP
- Line (trunk side)
– Bit rate: 9.952 Gbps for OC-192/STM-64
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_10DME_L card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_10DME_L cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_10DME_L cards.
– Connectors: LC
– Minimum output power: +3 dBm
– Maximum output power: +6 dBm
– Minimum SMSR: 30 dB
– Minimum optical extinction ratio: 10.5 dB
– 40 wavelength tunability at 100-GHz spacing, 80 wavelength tunability at 50-GHz spacing
– Receiver maximum return reflectance (Rx return loss): –27 dB
– Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB
– Minimum side mode suppression ratio: 30 dB
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
– For the currently available wavelengths for the MXP_MR_10DME_L card, see Table 10-30.
- Table A-44 provides the receiver trunk side specifications:
Table A-44 MXP_MR_10DME_L Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
|
|
None |
23 dB |
< 10 exp – 12 |
— |
–8 to –19 dBm |
+/– 1200 ps/nm |
2 dBm |
— |
19 dB |
< 10 exp – 12 |
— |
–9 to –19 dBm |
+/– 1000 ps/nm |
2 dBm |
— |
FEC |
10 dB |
< 10 exp – 5 |
< 10 exp – 15 |
–8 to –18 dBm |
+/– 800 ps/nm |
— |
1.5 dB |
Enhanced FEC |
19 dB |
< 10 exp – 4 |
< 10 exp – 15 |
–8 to –26 dBm |
+/– 800 ps/nm |
— |
2 dB |
8 dB |
< 10 exp – 4 |
< 10 exp – 15 |
–8 to –18 dBm |
+/– 800 ps/nm |
— |
1.5 dB |
– Receiver: APD
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
– Receiver input wavelength range: 1570 to 1604 nm
– Bit rate: 1.06 Gbps to 4.25 Gbps per client
– Code: Scrambled NRZ
– Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
– Maximum chromatic dispersion allowance: Based on SFP
– Loopback modes: Terminal and facility
– Connectors: LC
- Transmitter (client side)
– Maximum transmitter output power: –1 dBm
– Minimum transmitter output power: –6 dBm
– Center wavelength: Based on SFP
– Nominal wavelength: Based on SFP
– Transmitter: Based on SFP
– Maximum receiver level: –1 dBm at BER 1 * 10 exp – 12
– Minimum receiver level: –14 dBm at BER 1 * 10 exp – 12
– Receiver: APD
– Link loss budget: 8 dB minimum, at BER = 1 * 10 exp – 12
– Receiver input wavelength range: 1290 to 1605 nm or 850nm
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 2.25 lb (1.02 kg)
A.10.11 MXP_MR_10DMEX_C Card Specifications
The MXP_MR_10DMEX_C card has the following specifications:
– FC1G—Fibre Channel 1.06 Gbps
– FC2G—Fibre Channel 2.125 Gbps
– FC4G—Fibre Channel 4.25 Gbps
– FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)
– FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)
– FICON4G—Fiber connectivity 4.25 Gbps (IBM signal)
– ISC compatibility
– ISC peer 1G
– ISC peer 2G
– ONE_GE—One Gigabit Ethernet 1.125 Gbps
– Mixed configurations up to maximum line rate of 10.0 Gbps.
- Client ports: 8x SFP
- Line (trunk side)
– Bit rate: 9.952 Gbps for OC-192/STM-64
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_10DMEX_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_10DMEX_C cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_10DMEX_C cards.
– Connectors: LC
– Minimum output power: +3 dBm
– Maximum output power: +7 dBm
– Minimum Single-Mode Suppression Ratio (SMSR): 30 dB
– Minimum optical extinction ratio: 10 dB
– 41 wavelength tunability at 100-GHz spacing
– Receiver maximum return reflectance (Rx return loss): –27 dB
– Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB
– Minimum side mode suppression ratio: 30 dB
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
– For available wavelengths for the MXP_MR_10DMEX_C card, see Table 10-29.
Table A-45 MXP_MR_10DMEX_C Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
|
16 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 20 dBm |
+/– 1600 ps/nm |
— |
15 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 20 dBm |
— |
— |
TBD |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 20 dBm |
— |
|
12.5 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 20 dBm |
— |
— |
17 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 20 dBm |
+/- 4000 ps/nm |
— |
15.2 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 20 dBm |
+/- 2500 ps/nm |
— |
17.4 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 20 dBm |
|
3 |
– Receiver: APD
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
– Receiver input wavelength range: 1529 to 1562 nm
– Bit rate: 1.06 Gbps to 4.25 Gbps per client
– Code: Scrambled NRZ
– Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
– Maximum chromatic dispersion allowance: Based on SFP
– Loopback modes: Terminal and facility
– Connectors: LC
- Transmitter (client side)
– Maximum transmitter output power: –1 dBm
– Minimum transmitter output power: –6 dBm
– Center wavelength: Based on SFP
– Nominal wavelength: Based on SFP
– Transmitter: Based on SFP
– Maximum receiver level: –1 dBm at BER 1 * 10 exp – 12
– Minimum receiver level: –14 dBm at BER 1 * 10 exp – 12
– Receiver: APD
– Link loss budget: 8 dB minimum, at BER = 1 * 10 exp – 12
– Receiver input wavelength range: 1290 to 1605 nm or 850nm
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 2.25 lb (1.02 kg)
A.10.12 TXP_MR_10E Card Specifications
The TXP_MR_10E card has the following specifications:
– Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: +/– 1200 ps/nm (specified penalty)
– Loopback modes: Terminal and facility
Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10E card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10E card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10E card.
– Connectors: LC
– Maximum transmitter output power: +6 dBm
– Minimum transmitter output power: +3 dBm for C-band and +2 dBm for L-band
– Transmitter: LN external modulator transmitter
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
- Currently available wavelengths and versions of TXP_MR_10E:
C-band frequency plan (eight card versions, each with four tunable channels on the ITU 100-GHz grid):
– 1530.33 to 1533.07 nm (four channels)
– 1534.25 to 1537.00 nm (four channels)
– 1538.19 to 1540.95 nm (four channels)
– 1542.14 to 1544.92 nm (four channels)
– 1546.12 to 1548.92 nm (four channels)
– 1550.12 to 1552.93 nm (four channels)
– 1554.13 to 1556.96 nm (four channels)
– 1558.17 to 1561.01 nm (four channels)
L-band frequency plan (five card versions, each with eight tunable channels on the ITU 50-GHz grid):
– 1577.44 to 1580.35 nm (eight channels)
– 1580.77 to 1583.69 nm (eight channels)
– 1584.11 to 1587.04 nm (eight channels)
– 1587.46 to 1590.41 nm (eight channels)
– 1590.83 to 1593.79 nm (eight channels)
Table A-46 TXP_MR_10E Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
30 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 20 dBm |
+/– 1200 ps/nm |
26 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 20 dBm |
+ – 1000 ps/nm |
26 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 22 dBm |
— |
17 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 18 dBm |
+/– 800 ps/nm |
15 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 18 dBm |
— |
15 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 18 dBm |
+/– 800 ps/nm |
14 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 18 dBm |
— |
– Receiver: APD
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
– 10-Gigabit Small Form-factor Pluggable (XFP)-based SR
– Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192
– Code: Scrambled NRZ
– Fiber: 1310-nm single-mode
– Maximum chromatic dispersion allowance: 6.6 ps/nm
– Loopback modes: Terminal and facility
– Connectors: LC
– Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957, ITU-T G.691
- Transmitter (client side)
– Maximum transmitter output power: –1 dBm
– Minimum transmitter output power: –6 dBm
– Center wavelength: 1290 to 1330 nm
– Nominal wavelength: 1310 nm
– Transmitter: DFB laser
– Maximum receiver level: –1 dBm at BER 1 * 10 exp – 12
– Minimum receiver level: –14 dBm at BER 1 * 10 exp – 12
– Receiver: APD
– Link loss budget: 8 dB minimum, at BER = 1 * 10 exp – 12
– Receiver input wavelength range: 1290 to 1605 nm
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.13 TXP_MR_10E_C Card Specifications
The TXP_MR_10E_C card has the following specifications:
– Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: +/– 1200 ps/nm (specified penalty)
– Loopback modes: Terminal and facility
Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10E_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10E_C card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10E_C card.
– Connectors: LC
– Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957, and ITU-T G.709
– Maximum transmitter output power: +6 dBm
– Minimum transmitter output power: +3 dBm
– Transmitter: LN external modulator transmitter
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
- Currently available wavelengths and versions of TXP_MR_10E_C card:
There is a single version of the TXP_MR_10E_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-47 .
Table A-47 TXP_MR_10E_C Card Trunk Wavelengths
|
|
|
|
|
|
1 |
196.00 |
1529.55 |
42 |
193.95 |
1545.72 |
2 |
195.95 |
1529.94 |
43 |
193.90 |
1546.119 |
3 |
195.90 |
1530.334 |
44 |
193.85 |
1546.518 |
4 |
195.85 |
1530.725 |
45 |
193.80 |
1546.917 |
5 |
195.80 |
1531.116 |
46 |
193.75 |
1547.316 |
6 |
195.75 |
1531.507 |
47 |
193.70 |
1547.715 |
7 |
195.70 |
1531.898 |
48 |
193.65 |
1548.115 |
8 |
195.65 |
1532.290 |
49 |
193.60 |
1548.515 |
9 |
195.60 |
1532.681 |
50 |
193.55 |
1548.915 |
10 |
195.55 |
1533.073 |
51 |
193.50 |
1549.32 |
11 |
195.50 |
1533.47 |
52 |
193.45 |
1549.71 |
12 |
195.45 |
1533.86 |
53 |
193.40 |
1550.116 |
13 |
195.40 |
1534.250 |
54 |
193.35 |
1550.517 |
14 |
195.35 |
1534.643 |
55 |
193.30 |
1550.918 |
15 |
195.30 |
1535.036 |
56 |
193.25 |
1551.319 |
16 |
195.25 |
1535.429 |
57 |
193.20 |
1551.721 |
17 |
195.20 |
1535.822 |
58 |
193.15 |
1552.122 |
18 |
195.15 |
1536.216 |
59 |
193.10 |
1552.524 |
19 |
195.10 |
1536.609 |
60 |
193.05 |
1552.926 |
20 |
195.05 |
1537.003 |
61 |
193.00 |
1553.33 |
21 |
195.00 |
1537.40 |
62 |
192.95 |
1553.73 |
22 |
194.95 |
1537.79 |
63 |
192.90 |
1554.134 |
23 |
194.90 |
1538.186 |
64 |
192.85 |
1554.537 |
24 |
194.85 |
1538.581 |
65 |
192.80 |
1554.940 |
25 |
194.80 |
1538.976 |
66 |
192.75 |
1555.343 |
26 |
194.75 |
1539.371 |
67 |
192.70 |
1555.747 |
27 |
194.70 |
1539.766 |
68 |
192.65 |
1556.151 |
28 |
194.65 |
1540.162 |
69 |
192.60 |
1556.555 |
29 |
194.60 |
1540.557 |
70 |
192.55 |
1556.959 |
30 |
194.55 |
1540.953 |
71 |
192.50 |
1557.36 |
31 |
194.50 |
1541.35 |
72 |
192.45 |
1557.77 |
32 |
194.45 |
1541.75 |
73 |
192.40 |
1558.173 |
33 |
194.40 |
1542.142 |
74 |
192.35 |
1558.578 |
34 |
194.35 |
1542.539 |
75 |
192.30 |
1558.983 |
35 |
194.30 |
1542.936 |
76 |
192.25 |
1559.389 |
36 |
194.25 |
1543.333 |
77 |
192.20 |
1559.794 |
37 |
194.20 |
1543.730 |
78 |
192.15 |
1560.200 |
38 |
194.15 |
1544.128 |
79 |
192.10 |
1560.606 |
39 |
194.10 |
1544.526 |
80 |
192.05 |
1561.013 |
40 |
194.05 |
1544.924 |
81 |
192.00 |
1561.42 |
41 |
194.00 |
1545.32 |
82 |
191.95 |
1561.83 |
Table A-48 TXP_MR_10E _C Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
30 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 18 dBm |
+/– 1200 ps/nm |
26 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 18 dBm |
+ – 1000 ps/nm |
26 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 18 dBm |
— |
17 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 18 dBm |
+/– 800 ps/nm |
15.5 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 18 dBm |
— |
14 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 18 dBm |
+/– 800 ps/nm |
12 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 18 dBm |
— |
– Receiver: APD
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
– Receiver input wavelength range: 1529 to 1562 nm
– XFP-based SR
– Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192
– Code: Scrambled NRZ
– Fiber: 1310-nm single-mode
– Maximum chromatic dispersion allowance: 6.6 ps/nm
– Loopback modes: Terminal and facility
– Connectors: LC
- Transmitter (client side)
– Maximum transmitter output power: –1 dBm
– Minimum transmitter output power: –6 dBm
– Center wavelength: 1290 to 1330 nm
– Nominal wavelength: 1310 nm
– Transmitter: DFB laser
– Maximum receiver level: –1 dBm at BER 1 * 10 exp – 12
– Minimum receiver level: –14 dBm at BER 1 * 10 exp – 12
– Receiver: APD
– Link loss budget: 8 dB minimum, at BER = 1 * 10 exp – 12
– Receiver input wavelength range: 1290 to 1605 nm
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.14 TXP_MR_10E_L Card Specifications
The TXP_MR_10E_L card has the following specifications:
– Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: +/– 1200 ps/nm (specified penalty)
– Loopback modes: Terminal and facility
Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10E_L card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10E_L card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10E_L card.
– Connectors: LC
– Maximum transmitter output power: +6 dBm
– Minimum transmitter output power: +2 dBm
– Transmitter: LN external modulator transmitter
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
- Currently available wavelengths and versions of TXP_MR_10E_L card:
There is a single version of the TXP_MR_10E_L card. It is tunable across 80 wavelengths in the L band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-49 .
Table A-49 TXP_MR_10E_L Card Trunk Wavelengths
|
|
|
|
|
|
1 |
190.85 |
1570.83 |
41 |
188.85 |
1587.46 |
2 |
190.8 |
1571.24 |
42 |
188.8 |
1587.88 |
3 |
190.75 |
1571.65 |
43 |
188.75 |
1588.30 |
4 |
190.7 |
1572.06 |
44 |
188.7 |
1588.73 |
5 |
190.65 |
1572.48 |
45 |
188.65 |
1589.15 |
6 |
190.6 |
1572.89 |
46 |
188.6 |
1589.57 |
7 |
190.55 |
1573.30 |
47 |
188.55 |
1589.99 |
8 |
190.5 |
1573.71 |
48 |
188.5 |
1590.41 |
9 |
190.45 |
1574.13 |
49 |
188.45 |
1590.83 |
10 |
190.4 |
1574.54 |
50 |
188.4 |
1591.26 |
11 |
190.35 |
1574.95 |
51 |
188.35 |
1591.68 |
12 |
190.3 |
1575.37 |
52 |
188.3 |
1592.10 |
13 |
190.25 |
1575.78 |
53 |
188.25 |
1592.52 |
14 |
190.2 |
1576.20 |
54 |
188.2 |
1592.95 |
15 |
190.15 |
1576.61 |
55 |
188.15 |
1593.37 |
16 |
190.1 |
1577.03 |
56 |
188.1 |
1593.79 |
17 |
190.05 |
1577.44 |
57 |
188.05 |
1594.22 |
18 |
190 |
1577.86 |
58 |
188 |
1594.64 |
19 |
189.95 |
1578.27 |
59 |
187.95 |
1595.06 |
20 |
189.9 |
1578.69 |
60 |
187.9 |
1595.49 |
21 |
189.85 |
1579.10 |
61 |
187.85 |
1595.91 |
22 |
189.8 |
1579.52 |
62 |
187.8 |
1596.34 |
23 |
189.75 |
1579.93 |
63 |
187.75 |
1596.76 |
24 |
189.7 |
1580.35 |
64 |
187.7 |
1597.19 |
25 |
189.65 |
1580.77 |
65 |
187.65 |
1597.62 |
26 |
189.6 |
1581.18 |
66 |
187.6 |
1598.04 |
27 |
189.55 |
1581.60 |
67 |
187.55 |
1598.47 |
28 |
189.5 |
1582.02 |
68 |
187.5 |
1598.89 |
29 |
189.45 |
1582.44 |
69 |
187.45 |
1599.32 |
30 |
189.4 |
1582.85 |
70 |
187.4 |
1599.75 |
31 |
189.35 |
1583.27 |
71 |
187.35 |
1600.17 |
32 |
189.3 |
1583.69 |
72 |
187.3 |
1600.60 |
33 |
189.25 |
1584.11 |
73 |
187.25 |
1601.03 |
34 |
189.2 |
1584.53 |
74 |
187.2 |
1601.46 |
35 |
189.15 |
1584.95 |
75 |
187.15 |
1601.88 |
36 |
189.1 |
1585.36 |
76 |
187.1 |
1602.31 |
37 |
189.05 |
1585.78 |
77 |
187.05 |
1602.74 |
38 |
189 |
1586.20 |
78 |
187 |
1603.17 |
39 |
188.95 |
1586.62 |
79 |
186.95 |
1603.60 |
40 |
188.9 |
1587.04 |
80 |
186.9 |
1604.03 |
Table A-50 TXP_MR_10E Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
30 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 20 dBm |
+/– 1200 ps/nm |
26 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 20 dBm |
+ – 1000 ps/nm |
26 dB |
Off |
< 10 exp – 12 |
N/A |
– 8 to – 22 dBm |
— |
17 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 18 dBm |
+/– 800 ps/nm |
15.5 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 18 dBm |
— |
15 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 18 dBm |
+/– 800 ps/nm |
13 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 18 dBm |
— |
– Receiver: APD
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
– Receiver input wavelength range: 1570 to 1604 nm
– XFP-based SR
– Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192
– Code: Scrambled NRZ
– Fiber: 1310-nm single-mode
– Maximum chromatic dispersion allowance: 6.6 ps/nm
– Loopback modes: Terminal and facility
– Connectors: LC
- Transmitter (client side)
– Maximum transmitter output power: –1 dBm
– Minimum transmitter output power: –6 dBm
– Center wavelength: 1290 to 1330 nm
– Nominal wavelength: 1310 nm
– Transmitter: DFB laser
– Maximum receiver level: –1 dBm at BER 1 * 10 exp – 12
– Minimum receiver level: –14 dBm at BER 1 * 10 exp – 12
– Receiver: APD
– Link loss budget: 8 dB minimum, at BER = 1 * 10 exp – 12
– Receiver input wavelength range: 1290 to 1605 nm
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.15 TXP_MR_10EX_C Card Specifications
The TXP_MR_10EX_C card has the following specifications:
– Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: +/– 1600 ps/nm (specified penalty)
– Loopback modes: Terminal and facility
Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10EX_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10EX_C card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10EX_C card.
– Connectors: LC
– Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957, and ITU-T G.709
– Maximum transmitter output power: +6 dBm
– Minimum transmitter output power: +3 dBm
– Transmitter: LN external modulator transmitter
– Wavelength stability (drift): +/– 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
- Currently available wavelengths and versions of TXP_MR_10EX_C card:
There is a single version of the TXP_MR_10EX_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-51 .
Table A-51 TXP_MR_10EX_C Card Trunk Wavelengths
|
|
|
|
|
|
1 |
196.00 |
1529.55 |
42 |
193.95 |
1545.72 |
2 |
195.95 |
1529.94 |
43 |
193.90 |
1546.12 |
3 |
195.90 |
1530.334 |
44 |
193.85 |
1546.52 |
4 |
195.85 |
1530.725 |
45 |
193.80 |
1546.92 |
5 |
195.80 |
1531.116 |
46 |
193.75 |
1547.32 |
6 |
195.75 |
1531.507 |
47 |
193.70 |
1547.72 |
7 |
195.70 |
1531.898 |
48 |
193.65 |
1548.11 |
8 |
195.65 |
1532.290 |
49 |
193.60 |
1548.51 |
9 |
195.60 |
1532.681 |
50 |
193.55 |
1548.91 |
10 |
195.55 |
1533.073 |
51 |
193.50 |
1549.32 |
11 |
195.50 |
1533.47 |
52 |
193.45 |
1549.72 |
12 |
195.45 |
1533.86 |
53 |
193.40 |
1550.12 |
13 |
195.40 |
1534.250 |
54 |
193.35 |
1550.52 |
14 |
195.35 |
1534.643 |
55 |
193.30 |
1550.92 |
15 |
195.30 |
1535.036 |
56 |
193.25 |
1551.32 |
16 |
195.25 |
1535.429 |
57 |
193.20 |
1551.72 |
17 |
195.20 |
1535.822 |
58 |
193.15 |
1552.12 |
18 |
195.15 |
1536.216 |
59 |
193.10 |
1552.52 |
19 |
195.10 |
1536.609 |
60 |
193.05 |
1552.93 |
20 |
195.05 |
1537.003 |
61 |
193.00 |
1553.33 |
21 |
195.00 |
1537.40 |
62 |
192.95 |
1553.73 |
22 |
194.95 |
1537.79 |
63 |
192.90 |
1554.13 |
23 |
194.90 |
1538.186 |
64 |
192.85 |
1554.54 |
24 |
194.85 |
1538.581 |
65 |
192.80 |
1554.94 |
25 |
194.80 |
1538.976 |
66 |
192.75 |
1555.34 |
26 |
194.75 |
1539.371 |
67 |
192.70 |
1555.75 |
27 |
194.70 |
1539.766 |
68 |
192.65 |
1556.15 |
28 |
194.65 |
1540.162 |
69 |
192.60 |
1556.55 |
29 |
194.60 |
1540.557 |
70 |
192.55 |
1556.96 |
30 |
194.55 |
1540.953 |
71 |
192.50 |
1557.36 |
31 |
194.50 |
1541.35 |
72 |
192.45 |
1557.77 |
32 |
194.45 |
1541.75 |
73 |
192.40 |
1558.17 |
33 |
194.40 |
1542.142 |
74 |
192.35 |
1558.58 |
34 |
194.35 |
1542.539 |
75 |
192.30 |
1558.98 |
35 |
194.30 |
1542.936 |
76 |
192.25 |
1559.39 |
36 |
194.25 |
1543.333 |
77 |
192.20 |
1559.79 |
37 |
194.20 |
1543.730 |
78 |
192.15 |
1560.20 |
38 |
194.15 |
1544.128 |
79 |
192.10 |
1560.61 |
39 |
194.10 |
1544.526 |
80 |
192.05 |
1561.01 |
40 |
194.05 |
1544.924 |
81 |
192.00 |
1561.42 |
41 |
194.00 |
1545.32 |
82 |
191.95 |
1561.83 |
Table A-52 TXP_MR_10E _C Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
|
16 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 20 dBm |
+/– 1600 ps/nm |
— |
15 dB |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 20 dBm |
— |
— |
TBD |
Standard |
< 10 exp – 5 |
< 10 exp – 15 |
– 8 to – 20 dBm |
— |
|
12.5 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 20 dBm |
— |
— |
17 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 20 dBm |
+/- 4000 ps/nm |
— |
15.2 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 20 dBm |
+/- 2500 ps/nm |
— |
17.4 dB |
Enhanced |
< 7 x 10 exp – 4 |
< 10 exp – 15 |
– 8 to – 20 dBm |
|
3 |
– Receiver: APD
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
– Receiver input wavelength range: 1529 to 1562 nm
– XFP-based SR
– Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192
– Code: Scrambled NRZ
– Fiber: 1310-nm single-mode
– Maximum chromatic dispersion allowance: 6.6 ps/nm
– Loopback modes: Terminal and facility
– Connectors: LC
- Transmitter (client side)
– Maximum transmitter output power: –1 dBm
– Minimum transmitter output power: –6 dBm
– Center wavelength: 1290 to 1330 nm
– Nominal wavelength: 1310 nm
– Transmitter: DFB laser
– Maximum receiver level: –1 dBm at BER 1 * 10 exp – 12
– Minimum receiver level: –14 dBm at BER 1 * 10 exp – 12
– Receiver: APD
– Link loss budget: 8 dB minimum, at BER = 1 * 10 exp – 12
– Receiver input wavelength range: 1290 to 1605 nm
– Height: 12.650 in. (321.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.000 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.16 ADM-10G Card Specifications
The ADM-10G card has the following specifications:
– Bit rate: OC-3/STM-1 (155.520 Mb/s); OC-12/STM-3 (622.08 Mb/s); OC-48/STM-16 (2488.32 Mb/s); OC-192/STM-64 (9.95328 Gbps)
– Code: Scrambled NRZ
– Fiber: 1310-nm single-mode for ONS-XC-10GS1 XFP or 1530.33 to 1554.94-nm single-mode for ONS-XC-10G-xx.x XFP
– Maximum chromatic dispersion allowance: up to 3600 ps/nm
– Loopback modes: Terminal, facility, and cross-connect
– Connectors: LC
– Transmitter: LN external modulator transmitter
– Maximum transmitter output power: Depends on XFP that is used
– Minimum transmitter output power: Depends on XFP that is used
– Wavelength stability (drift): +/– 25 picometers (pm)
– Receiver: APD
– Receiver input wavelength range: Depends on XFP that is used
– Receiver sensitivity: depends on XFP that is used
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
– Height: 12.65 in. (321.3 mm)
– Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.00 in. (228.6 mm)
– Depth with backplane connector: 9.250 in. (235 mm)
– Weight not including clam shell: 5.07 lb (2.3 kg)
A.10.17 GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Card Specifications
The GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE cards have the following specifications:
– Bit rate: 11.1 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode) or 10.3125 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode disabled)
– Code: Scrambled NRZ
– Fiber: 1550-nm single-mode
– Maximum chromatic dispersion allowance: – 500 to 1600 ps/nm (specified penalty)
– Loopback modes: Terminal and facility
Caution
You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the GE_XP and GE_XPE card in a loopback on the trunk port. Do not use direct fiber loopbacks with the GE_XP and GE_XPE card. Using direct fiber loopbacks causes irreparable damage to the GE_XP and GE_XPE card.
– Connectors: LC
– Maximum transmitter output power: +3 dBm
– Minimum transmitter output power: -1 dBm
– Transmitter: EML laser
– Wavelength stability (drift): +/– 100 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/– 25 pm.
- Currently available wavelengths and versions of GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE: C Band, 100 GHz spacing.
- Receiver (trunk side, see Table A-53 )
– Receiver: APD
– Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp – 12 including dispersion
Table A-53 GE_XP and GE_XPE Card Receiver Trunk Side Specifications
|
|
|
|
|
Chromatic Dispersion Tolerance
|
30 dB |
Off |
1.00E – 12 |
N/A |
– 7 to – 23 dBm |
— |
30 dB |
Off |
1.00E – 12 |
N/A |
– 7 to – 20 dBm |
– 500 to 1600 ps/nm |
24 dB |
Off |
1.00E – 12 |
N/A |
– 7 to – 18 dBm |
— |
27 dB |
Off |
1.00E – 12 |
N/A |
– 7 to – 18 dBm |
– 500 to 1600 ps/nm |
18 dB |
Standard |
1.00E – 05 |
1.00E – 15 |
– 7 to – 18 dBm |
— |
19 dB |
Standard |
1.00E – 05 |
1.00E – 15 |
– 7 to – 18 dBm |
– 500 to 1600 ps/nm |
30 dB |
Enhanced |
1.00E – 04 |
1.00E – 15 |
– 7 to – 27 dBm |
— |
30 dB |
Enhanced |
1.00E – 04 |
1.00E – 15 |
– 7 to – 24 dBm |
– 500 to 1600 ps/nm |
15 dB |
Enhanced |
1.00E – 04 |
1.00E – 15 |
– 7 to – 18 dBm |
— |
15 dB |
Enhanced |
1.00E – 04 |
1.00E – 15 |
– 7 to – 18 dBm |
– 500 to 1600 ps/nm |
– Bit rate: 1.125Gbps (GE) or 10.3125Gbps (10GE)
– Code: Scrambled NRZ
– Fiber: 1310-nm single-mode or 850-nm multimode
– Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
– Loopback modes: Terminal and facility
– Connectors: LC (optical)
- Transmitter (client side): Depends on the SFP that is used.
- Receiver (client side): Depends on the SFP that is used.
- Environmental
– Power consumption: 95.00 W (maximum), 2 A at -48 V for GE_XP and GE_XPE cards
– Power consumption: 80.00 W (maximum), 1.67 A at -48 V for 10GE_XP and 10GE_XPE cards
– Height: 12.992 in. (330 mm)
– Width: 10GE_XP and 10GE_XPE: 0.921 in. (23.4 mm)
GE_XP and GE_XPE: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.448 in. (240 mm)
– Weight not including clam shell: 10GE-XP and 10GE_XPE, 1.04 kg;
GE-XP and GE_XPE, 1.36 kg.
A.10.18 OTU2_XP Card Specifications
The OTU2_XP card has the following specifications:
– Bit rate: OC-192/STM-64 (9.95328 Gbps), 10GE (10.3125 Gbps), or 10G FC (10.51875 Gbps)
– Code: Scrambled NRZ
– Fiber: 1310-nm single-mode for ONS-XC-10GS1 XFP or 1530.33-nm to 1561.42-nm single-mode for ONS-XC-10G-xx.x XFP
– Maximum chromatic dispersion allowance: Depends on the XFP that is used
– Loopback modes: Terminal and facility
– Connectors: LC
– Transmitter: EML
– Maximum transmitter output power: Depends on the XFP that is used
– Minimum transmitter output power: Depends on the XFP that is used
– Wavelength stability (drift): Depends on the XFP that is used
– Receiver: APD
– Receiver input wavelength range: Depends on XFP that is used
– Receiver sensitivity: Depends on XFP that is used
– Link loss budget: Depends on XFP that is used
– Height: 13.043 in. (331.3 mm)
– Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
– Depth: 9.413 in. (239.1 mm)
– Depth with backplane connector: 9.909 in. (251.7 mm)
– Weight not including clam shell: 2.38 lb (1.08 kg)