Cisco ONS 15310-CL and Cisco ONS 15310-MA Reference Manual, Release 7.0
Appendix A, Hardware Specifications
Downloads: This chapterpdf (PDF - 269.0KB) The complete bookPDF (PDF - 11.36MB) | Feedback

Specifications

Table Of Contents

Specifications

A.1  Cisco ONS 15310-CL Shelf Specifications

A.1.1  Bandwidth

A.1.2  Expansion Slot

A.1.3  Internal Cards

A.1.4  15310-CL-CTX

A.1.5  Configurations

A.1.6  Cisco Transport Controller

A.1.7  TL1 Craft Interface

A.1.8  LEDs

A.1.9  Alarm Interface

A.1.10  DS1 Interface

A.1.11  DS3/EC1 Interface

A.1.12  Nonvolatile Memory

A.1.13  BITS Interface

A.1.14  Push Buttons

A.1.15  System Timing

A.1.16  Power Specifications

A.1.17  Environmental Specifications

A.1.18  Shelf Dimensions

A.2  Cisco ONS 15310-MA Shelf Specifications

A.2.1  Alarm Interface

A.2.2  UDC Interface

A.2.3  Cisco Transport Controller LAN Interface

A.2.4  TL1 Craft Interface

A.2.5  Configurations

A.2.6  LEDs

A.2.7  Push Buttons

A.2.8  BITS Interface

A.2.9  System Timing

A.2.10  Power Specifications

A.2.11  Environmental Specifications

A.2.12  Fan-Tray Assembly Specifications

A.2.13  Shelf Dimensions

A.3  Card Specifications

A.3.1  CTX2500 Card

A.3.2  Nonvolatile Memory

A.3.3  CE-100T-8 and ML-100T-8 Cards

A.3.4  DS1-28/DS3-EC1-3 and DS1-84/DS3-EC1-3 Cards

A.3.5  Filler Cards

A.4  SFP Specifications


Specifications



Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.


This appendix contains shelf, card, and Small Form-factor Pluggable (SFP) specifications for the Cisco ONS 15310-CL and Cisco ONS 15310-MA.

A.1  Cisco ONS 15310-CL Shelf Specifications

This section includes hardware and software specifications.

A.1.1  Bandwidth

The following bandwidth specifications apply to the ONS 15310-CL:

Total bandwidth: 2.054 Gbps

Optical: 1.24 Gbps (2 x OC-12)

Electrical: 188 Mbps

Expansion: 622 Mbps (OC-12)

A.1.2  Expansion Slot

Total card slots: 1 expansion slot for CE-100T-8 and ML-100T-8 cards. A blank card (15310-EXP-FILLER) can also be plugged into the expansion slot.

A.1.3  Internal Cards

The following internal cards are available in the ONS 15310-CL:

15310-CL-CTX card

Interconnect card

Connector expansion card

A.1.4  15310-CL-CTX

The 15310-CL-CTX card has the following specifications:

Optical ports

Two user upgradeable and hot swappable SFPs with SONET interface support

Support for multirate SFPs (155.520 Mbps and 622.080 Mbps)

Support for operating the two optical facilities at different line rates in unprotected facility mode (non 1+1 Automatic Protection Switching [APS] operation)

DS-1 ports

Supports Telcordia GR-499-compliant 1.544 Mbps (DS-1) interface

Performance monitoring (PM) is provided through the interface to allow validation of signal quality.

Any outgoing DS-1 signal can be retimed to eliminate accumulated jitter and wander at the point of egress from a synchronous network.

Any incoming T1 signal from the transport element can also be used as a timing source.

DS-3/EC1 ports

Supports Telcordia GR-499-compliant 44.736 Mbps (DS3) interfaces or EC1.

PM is provided through the interface to allow validation of signal quality. Each port can be provisioned in any combination of DS-3 or EC1.

Building integrated timing supply (BITS)

Supports one BITS input and one BITS output

The BITS I/O ports support a 100-ohm termination for external 1.544 Mbps DS1 timing signals.

Alarm

The alarm system provides three alarm inputs and two contacts for alarm outputs.

LAN

Supports a 10/100-Mbps Ethernet interface for Cisco Transport Controller/Transaction Language One (CTC/TL1) provisioning.

For node access in secure mode, SSL (for TL1) and HTTPS (for CTC) security protocols are supported.

Craft interface

An EIA/TIA-232 craft interface is provided and is used for TL1 provisioning.

The craft interface is set to 9600 baud, no parity, and 1 stop bit by default.

64-kbps user data channel (UDC) digital interface

The 6- kbps digital interface provides a digital input and output.

Any F1 byte that is accessible on the system is interfaced at the UDC connector.

The UDC provides a simplex interface. Protection for UDC overhead channel(s) follows interface line protection for traffic.

The UDC can be enabled or disabled through the management interfaces. The default state is disabled.

The UDC supports a 64-kbps serial interface adaptation function to overhead byte F1.

The physical interface is defined in ITU-T G.703 as a 120-ohm, twisted pair connection. The jitter specification is defined in ITU-T G.823.

The physical interface is defined in ITU-T G.703 as a 120-ohm, twisted pair connection. The jitter specification is defined in ITU-T G.823.

The UDC supports a serial port interface adaptation function to overhead bytes F1. This is an EIA/TIA-232 interface capable of 9.6-, 19.2-, 38.4-, and 56-kbps operation. The rate is selectable through the management interface. The default is 56 kbps with no parity and 1 stop bit.

A.1.5  Configurations

The ONS 15310-CL supports the following configurations:

Two-fiber path protection

1+1 protection

Path protected mesh network (PPMN)

Add/drop multiplexer (ADM)

Point-to-point (PPP) terminal mode

A.1.6  Cisco Transport Controller

CTC, the ONS 15310-CL graphical user interface (GUI), has the following specifications:

10/100BaseT

15310-CL-CTX access: RJ-45 connector

A.1.7  TL1 Craft Interface

TL1, the ONS 15310-CL craft interface, has the following specifications:

Speed: 9600 baud, no parity, 1 stop bit

15310-CL-CTX: EIA/TIA-232 with RJ-45 type connector

A.1.8  LEDs

Table A-1 describes the possible LED colors and their significance.

Table A-1 LED Description

LED
Color

FAIL

Red for system failure or during initialization

ALARM

Red (Major and Critical)

Amber (Minor)

PWR

Green (AC source present or both DC sources present)

Amber (one DC source present)

SYNC

Green (primary and secondary reference synchronization)

Amber (only one reference)

Red (loss of both references)


A.1.9  Alarm Interface

The ONS 15310-CL alarm interface has the following specifications:

Visual: Critical (red LED), Major (red LED), Minor (amber LED)

Three alarm inputs and two alarm contacts, all on the same RJ-45 connector (ALARM port)

A.1.10  DS1 Interface

The ONS 15310-CL DS-1 interface has the following specifications:

21 DS-1 (1.544 Mbps) ports

Connector: LFH96 (100-ohm balanced)

Any two ports can be used as primary and secondary timing sources

A DS01 output can be retimed to system clock on a per-port basis

A.1.11  DS3/EC1 Interface

The ONS 15310-CL DS3/EC1 interface has the following specifications:

Three DS3 (44.736 Mbps)/EC1 (51.84 Mbps) ports

Connector: 75-ohm mini-BNC connector

Ports can be any combination of DS-3 and EC-1

A.1.12  Nonvolatile Memory

The ONS 15310-CL nonvolatile memory has the following specifications:

128 MB, Compact Flash card

A.1.13  BITS Interface

The ONS 15310-CL BITS interface has the following specifications:

One DS-1 BITS input

One derived DS-1 output

A.1.14  Push Buttons

The ONS 15310-CL has the following push buttons:

Lamp test: When momentarily pushed, lights all LEDs on the ONS 15310-CL front panel. If an LED has more than one color, all the colors will be cycled when the lamp test button is pushed.


Note Another use for the lamp test button is to reset the CTC password to its default value (otbu+1). To reset the password, press the lamp test button for at least five seconds, release it for a maximum of five seconds, then press it again for at least five seconds. After the button is released, the default password is set.


System reset: When pressed, performs a soft reset (does not impact traffic).

A.1.15  System Timing

The ONS 15310-CL has the following timing specifications:

+/- 20 ppm SONET Minimum Clock (SMC) free-running internal clock

Maintains SMC holdover (+/- 4.6 ppm for first 24 hours) in the event of reference frequency loss

Timing reference: External BITS, line optical port, any DS-1 clock, and internal clock

A.1.16  Power Specifications

The ONS 15310-CL has the following power specifications:

Input power: -48 VDC (dual DC power supply model) or 100/240 VAC (AC power model)

Maximum power consumption

DC chassis with no expansion board: 60 W

DC chassis with expansion board: 115 W

AC chassis with no expansion board: 70 W

AC chassis with expansion board: 140 W

Power requirements: -42 to -56 VDC or 100/240 VAC (+/- 10 percent)

Power terminals: Three-prong male locking connector for DC power supply model or three-prong male AC connector for AC power model


Note An ONS 15310-CL that uses DC power is classified as DC-I (DC Isolated). This means that the DC return (RET) conductor at the DC power input connector is not bonded to the chassis frame ground.


A.1.17  Environmental Specifications

The ONS 15310-CL has the following environmental specifications:

Operating temperature: 0 to +55 degrees Celsius (32 to +131 degrees Fahrenheit) for AC chassis; -40 to +65 degrees Celsius (-40 to +149 degrees Fahrenheit) for dual-DC chassis

Operating humidity: 5 to 95 percent, noncondensing

A.1.18  Shelf Dimensions

The ONS 15310-CL has the following shelf dimensions:

Height: 1 Rack Unit (RU), 1.75 inches (4.45 cm)

Width:

19.0 inches (48.3 cm)

23.0 inches (58.4 cm) including rackmount brackets

Depth:

15.0 inches (38.1 cm) sheet metal only

15.8 inches (40.2) including mini-BNC and DC inlet connectors

Weight:

11.5 lb. empty

12.5 lb. maximum (line card installed)

A.2  Cisco ONS 15310-MA Shelf Specifications

This section provides ONS 15310-MA topologies; Cisco Transport Controller (CTC) specifications; LAN, TL1, modem, alarm, and electrical interface assembly (EIA) interface specifications; timing, power, and environmental specifications; and shelf dimensions.

A.2.1  Alarm Interface

The ONS 15310-MA alarm interface has the following specifications:

The alarm interface provides 32 alarm inputs and 8 contacts for alarm outputs.

Connector J6: Alarm inputs

Connector J7: Alarm outputs

A.2.2  UDC Interface

The ONS 15310-MA 64-kbps user data channel (UDC) digital interface has the following specifications:

The 64- kbps digital interface provides a digital input and output.

Any F1 byte that is accessible on the system is interfaced at the UDC connector.

The UDC provides a simplex interface. Protection for UDC overhead channel(s) follows interface line protection for traffic.

The UDC can be enabled or disabled through the management interfaces. The default state is disabled.

The physical interface is defined in ITU-T G.703 as a 120-ohm, twisted pair connection. The jitter specification is defined in ITU-T G.823.

The UDC supports a serial port interface adaptation function to overhead bytes F1. This is an EIA/TIA-232 interface capable of 9.6-, 19.2-, 38.4-, and 56-kbps operation. The rate is selectable through the management interface. The default is 56 kbps with no parity and 1 stop bit.

Connector J3: UDC

A.2.3  Cisco Transport Controller LAN Interface

The ONS 15310-MA CTC LAN interface has the following specifications:

10/100BaseT

CTX2500 access: RJ-45 connector

Connector J3: LAN port

A.2.4  TL1 Craft Interface

The ONS 15310-MA TL1 craft interface has the following specifications:

Speed: 9600 baud, no parity, 1 stop bit

CTX2500: EIA/TIA-232 with RJ-45 type connector

Connector J2: Craft port

A.2.5  Configurations

The ONS 15310-MA supports the following configurations:

Two-fiber path protection

1+1 protection

Path protected mesh network (PPMN)

Add/drop multiplexer (ADM)

Point-to-point (PPP) terminal mode

A.2.6  LEDs

Table A-1 describes the system-level LEDs, located on the on the ONS 15310-MA fan tray, and the possible LED colors and their significance.

Table A-2 LED Description

LED
Color and Meaning

FAIL

Red indicates system failure or during initialization

CR

Red indicates a critical alarm is present on the shelf assembly.

MJ

Red indicates a major alarm is present on the shelf assembly.

MN

Amber indicates a minor alarm is present on the shelf assembly.

REM

Red indicates a remote alarm is present on the shelf assembly.

PWR A

PWR B

Green indicates that a DC power source present and within normal operating range.

Red indicates that DC power source is not present, or is present and not within normal operating range.


A.2.7  Push Buttons

The ONS 15310-MA has the following push buttons:

Lamp test: When momentarily pushed, lights all LEDs on the ONS 15310-MA front panel. If an LED has more than one color, all the colors will be cycled when the lamp test button is pushed.


Note Another use for the lamp test button is to reset the CTC password to its default value (otbu+1). To reset the password, press the lamp test button for at least five seconds, release it for a maximum of five seconds, then press it again for at least five seconds. After the button is released, the default password is set.


A.2.8  BITS Interface

The ONS 15310-MA has the following building integrated timing supply (BITS) specifications:

Supports two BITS inputs and two BITS outputs

The BITS I/O ports support a 100-ohm termination for external 1.544 Mbps DS1 timing signals.

Connector J4: BITS1; Connector J5: BITS2

A.2.9  System Timing

The ONS 15310-MA has the following timing specifications:

+/- 20 ppm SONET Minimum Clock (ST3) free-running internal clock

Maintains SMC holdover (+/- 4.6 ppm for first 24 hours) in the event of reference frequency loss

Timing reference: External BITS, line optical port, any DS-1 clock, and internal clock

A.2.10  Power Specifications

The ONS 15310-MA has the following power specifications:

Input power: -48 VDC

Maximum power consumption

Chassis with no cards installed (fan tray only): 55 W

Chassis with cards installed: 347 W

Power requirements: -44 to -54 VDC

Power terminals: Three-prong male locking connector


Note An ONS 15310-MA that uses DC power is classified as DC-I (DC Isolated). This means that the DC return (RET) conductor at the DC power input connector is not bonded to the chassis frame ground.


A.2.11  Environmental Specifications

The ONS 15310-MA has the following environmental specifications:

Operating temperature: -40 to +65 degrees Celsius (-40 to +149 degrees Fahrenheit)

Operating humidity: 5 to 95 percent, noncondensing

A.2.12  Fan-Tray Assembly Specifications

Environmental

Operating temperature: -40 to +65 degrees Celsius (-40 to 149 degrees Fahrenheit)

Operating humidity: 5 to 90%, noncondensing

Power

50 W, 4.2 Amps (at 12 V), 170 BTU/hr

Shelf Acoustics (NEBS acoustic noise compliant)

Normal fan speed: 58 dBA

High fan speed: 64 dBA

A.2.13  Shelf Dimensions

The ONS 15310-MA has the following shelf dimensions:

Height: 6 Rack Units (RUs), 10.44 inches (26.51 cm)

Width:

10.67 inches (27.10 cm)

Depth:

12 inches (20.5 cm) without cables installed

13.7 inches (34.8 cm) with cables installed

Weight:

25 lbs. (11.3 kg) maximum (line cards, fan-tray assembly, and two electrical interface assemblies (EIAs) installed)

A.3  Card Specifications

This section provides specifications for the cards that can be installed in the 15310-CL expansion slot, including the CE-100T-8, ML-100T-8, and Filler cards. It also includes the 15310-MA electrical and CTX2500 cards. For compliance information, refer to the Cisco Optical Transport Products Safety and Compliance Information document.

A.3.1  CTX2500 Card

The CTX2500 card is installed in Slots 3 and 4 of the ONS 15310-MA only. The CTX2500 has the following specifications.

LAN Port

Supports a 10/100-Mbps Ethernet interface for Cisco Transport Controller/Transaction Language One (CTC/TL1) provisioning.

For node access in secure mode, SSL (for TL1) and HTTPS (for CTC) security protocols are supported.

CRAFT Port

An EIA/TIA-232 craft interface is provided and is used for TL1 provisioning.

The craft interface is set to 9600 baud, no parity, and 1 stop bit by default.

Nonvolatile memory

128 MB, Compact Flash card

Optical ports: Line

Bit rate: OC-3 (155.520 Mbps), OC-12, (622.080 Mbps), and OC-48 (2488.320 Mbps), depending on the SFP installed


Note Both optical interfaces on the card can be configured as OC-3, OC-12, or OC-48.


Code: Scrambled NRZ

Fiber: depends on the SFP used
(see the "SFP Specifications" section)

Loopback modes: Terminal and facility

Connectors: LC duplex connector for each SFP

Compliance: Telcordia SONET, Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957

Optical ports: Transmitter

Maximum transmitter output power: Depends on the SFP used
(see the "SFP Specifications" section)

Minimum transmitter output power: Depends on the SFP used
(see the "SFP Specifications" section)

Center wavelength: See wavelength plan

Center wavelength accuracy: 1 nm to 4 nm, depending on the SFP used

Transmitter: DFB laser

Optical ports: Receiver

Maximum receiver level: Depends on the SFP used
(see the "SFP Specifications" section)

Minimum receiver level: Depends on the SFP used
(see the "SFP Specifications" section)

Receiver: PIN PD

Receiver input wavelength range: Depends on the SFP used

Environmental

Operating temperature:

C-Temp: +23 to +131 degrees Fahrenheit (-5 to +55 degrees Celsius)

I-Temp: -40 to +149 degrees Fahrenheit (-40 to +65 degrees Celsius)

Operating humidity: 5 to 95 percent, noncondensing

Power consumption: 9.28 W, 0.19 A, 31.68 BTU/hr

Dimensions

Height: 6.94 in. (167.28 mm)

Width: 1.45 in. (36.83 mm)

Depth: 8.35 in. (212.09 mm)

Weight not including clam shell: 1.6 lb (0.73 kg)

LAN Port

Supports a 10/100-Mbps Ethernet interface for Cisco Transport Controller/Transaction Language One (CTC/TL1) provisioning.

CRAFT Port

An EIA/TIA-232 craft interface is provided and is used for TL1 provisioning.

The craft interface is set to 9600 baud, no parity, and 1 stop bit by default.

A.3.2  Nonvolatile Memory

The ONS 15310-MA nonvolatile memory has a 128 MB Compact Flash card

A.3.3  CE-100T-8 and ML-100T-8 Cards

The CE-100T-8 and ML-100T-8 cards have the following specifications:

Environmental

Operating temperature

C-Temp: 0 to +55 degrees Celsius (32 to 131 degrees Fahrenheit)

Operating humidity: 5 to 95%, noncondensing

Power consumption: 1.10A, 53 W

Dimensions

Height: 176 mm (6.93 in.)

Width: 34.29 mm (1.35 in.)

Depth: 238.25 mm (9.38 in.)

Weight (not including clam shell): 0.499 kg (1.1 lb)

A.3.4  DS1-28/DS3-EC1-3 and DS1-84/DS3-EC1-3 Cards

The ONS 15310-MA DS1-28/DS3-EC1-3 and DS1-84/DS3-EC1-3 cards have the following specifications:

For DS1:

For DS1:

Input

Bit rate: 1.544 Mbps +/- 32 ppm

Frame format: Unframed, SF (D4), ESF

Line code: AMI, B8ZS

Termination: AMP Champ

Input impedance: 100 ohms

Cable loss: Max 655 feet ABAM #22 or #24 AWG

AIS: TR-TSY-000191 compliant

Output

Bit rate: 1.544 Mbps +/- 32 ppm

Frame format: Unframed, SF (D4), ESF

Line code: AMI, B8ZS

Termination: AMP Champ

Input impedance: 100 ohms

Cable loss: Max 655 feet ABAM #22 or #24 AWG

AIS: TR-TSY-000191 compliant

Power level: 12.5 to 17.9 dBm, centered at 772 KHz, -16.4 to -11.1 dBm centered at 1544 KHz

Pulse shape: Telcordia GR-499-CORE Figure 9-5

Pulse amplitude: 2.4 to 3.6 V peak-to-peak

Loopback modes: Terminal and facility

Line build out: 0 - 131 ft., 132 - 262 ft., 263 - 393 ft., 394 - 524 ft., 525 - 655 ft.

Electrical interface: 64-pin Champ connectors on high-density EIA

For DS3:

Input

Bit rate: 44.736 Mbps +/- 20 ppm

Frame format: Unframed, M13, C-bit

Line code: B3ZS

Termination: Unbalanced coaxial cable

Input impedance: 75 ohms +/-5 percent

Cable loss: Max 450 feet with 734A or 728A

AIS: TR-TSY-000191 compliant

Output

Bit rate: 44.736 Mbps +/- 20 ppm

Frame format: Unframed, M13, C-bit

Line code: B3ZS

Termination: Unbalanced coaxial cable

Input impedance: 75 ohms +/-5 percent

Cable loss: Max 450 feet with 734A or 728A cable

AIS: TR-TSY-000191 compliant

Power level: -1.8 to +5.7 dBm

Pulse shape: ANSI T1.102-1988 Figure 8

Pulse amplitude: 0.36 to 0.85 V peak

Loopback modes: Terminal and facility

Line build out: 0 to 225 feet, 226 to 450 feet

Electrical interface: BNC Connectors on high-density EIA

For EC-1:

Input

Bit rate: 51.84 Mbps +/- 20 ppm

Frame format: SONET

Line code: B3ZS

Termination: Unbalanced coaxial cable

Input impedance: 75 ohms +/- 5 percent

Cable loss: Max 450 feet 734A or 728A

AIS: TR-TSY-000191 compliant

Output

Bit rate: 51.84 Mbps +/- 20 ppm

Frame format: SONET

Line code: B3ZS

Termination: Unbalanced coaxial cable

Input impedance: 75 ohms +/-5 percent

Cable loss: Max 450 feet 734A or 728A

AIS: TR-TSY-000191 compliant

Power level: -1.8 +/- 5.7 dBm

Pulse shape: ANSI T1.102-1988 Figure 8

Pulse amplitude: 0.36 to 0.85 V peak to peak

Loopback modes: Terminal and facility

Line build out: 0 to 225 feet, 226 to 450 feet

Electrical interface: BNC connectors on high-density EIA

Surge protection: Telcordia GR-1089

Operating temperature: I-Temp, -40 to +65 degrees Celsius.

Operating humidity: 5 to 95 percent, noncondensing

Power consumption: 36.60 W, 0.76 A, 124.97 BTU/hr

Dimensions

Height: 6.93 in. (17.60 cm)

Width: 1.35 in. (3.43 cm)

Depth: 8.80 in. (22.35 cm)

Card weight: 1.5 lbs (0.68 kg)

A.3.5  Filler Cards

The 15310-EXP-FILLER card has the following specifications:

Environmental

Operating temperature

I-Temp: -40 to +65 degrees Celsius (-40 to 149 degrees Fahrenheit)

Operating humidity: 5 to 95 percent, noncondensing

Dimensions

Height: 6.93 in. (176 mm)

Width:1.35 in. (34.29 mm)

Depth: 9.38 in. (238.25 mm)

Card weight (not including clam shell): 0.9 lb (0.45 kg)

The 15310-CTX-FILLER card has the following specifications:

Environmental

Operating temperature

I-Temp: -40 to +65 degrees Celsius (-40 to 149 degrees Fahrenheit)

Operating humidity: 5 to 95%, noncondensing

Dimensions

Height: 6.94 in. (167.28 mm)

Width: 1.450 in. (36.83 mm)

Depth:8.35 in. (212.09 mm)

Weight not including clam shell: 0.51 lb (0.23 kg)

A.4  SFP Specifications

Table A-3 lists specifications for available SFPs that can be used with the 15310-CL-CTX and CTX2500 cards. Table A-4 lists specifications for available SFPs that can be used only with the CTX2500 card.

The 15310-CL-CTX card does not have a faceplate because it is located inside the chassis; therefore, the two SFP slots are located on the ONS 15310-CL faceplate, just to the left of the LAN port. The two SFP slots on the CTX2500 are located on CTX2500 faceplate.

Table A-3 SFP Specifications—ONS 15310-CL and ONS 15310-MA

SFP Product ID
Interface
Transmitter Output Power Min/Max (dBm)
Receiver Input Power Min/Max (dBm)

ONS-SI-155-L1

OC-3

-5.0 to 0

-34 to -10

ONS-SI-155-L2

OC-3

-5.0 to 0

-34 to -10

ONS-SI-155-I1

OC-3

-15 to -8.0

-28 to -8

ONS-SI-622-L1

OC-12

-3.0 to 2.0

-28 to -8

ONS-SI-622-L2

OC-12

-3.0 to 2.0

-28 to -8

ONS-SI-622-I1

OC-12/OC-3

-15 to -8.0

-28 to -8


Table A-4 SFP Specifications—ONS 15310-MA Only

SFP Product ID
Interface
Transmitter Output Power Min/Max (dBm)
Receiver Input Power Min/Max (dBm)

ONS-SE-155-1470= through ONS-SE-155-1610=

OC-3

0 to +5

-34 to -3 (at BER 10-10)

ONS-SE-622-1470= through ONS-SE-622-1610=

OC-12

0 to +5

-28 to -3 (at BER 10-10)

ONS-SI-2G-I1=

OC-48

-5.0 to 0

-18 to -0

ONS-SI-2G-L1=

OC-48

-3 to +2

-27 to -9

ONS-SI-2G-L2=

OC-48

-3 to +2

-28 to -9

ONS-SI-2G-S1=

OC-48

-10 to -3

-18 to -3

ONS-SC-2G-30.3= through ONS-SC-2G-60.6=

OC-48

0 to +4

-28 to -9


Table A-5 provides cabling specifications for the single-mode fiber (SMF) SFPs that can be used with both the 15310-CL-CTX and the ONS 15310-MA CTX2500. The ports of the listed SFPs have LC-type connectors. Table A-6 provides cabling specifications for SFPs that can only be used with the ONS 15310-MA CTX-2500 card.

Table A-5 Single-Mode Fiber SFP Port Cabling Specifications—ONS 15310-CL and ONS 15310-MA 

SFP Product ID
Wavelength 1
Fiber Type
Cable Distance

ONS-SI-155-L1 Long Reach

1310 nm

9 micro SMF

50 km (31.07 miles)

ONS-SI-155-L2 Long Reach

1550 nm

9 micro SMF

100 km (62.15 miles)

ONS-SI-155-I1 Intermediate Reach

1310 nm

9 micro SMF

21 km (13.05 miles)

ONS-SI-622-L1 Long Reach

1310 nm

9 micron SMF

42 km (26.10 miles)

ONS-SI-622-L2 Long Reach

1550 nm

9 micron SMF

85 km (52.82 miles)

ONS-SI-622-I1 Intermediate Reach

1310 nm

9 micron SMF

21 km (13.05 miles)

1 Typical loss on a 1310-nm wavelength SMF is 0.6 dB/km.


Table A-6 Single-Mode Fiber SFP Port Cabling Specifications—ONS 15310-MA Only

SFP Product ID
Wavelength 1
Fiber Type
Cable Distance

ONS-SE-155-1470 through ONS-SE-155-1610 (CWDM)

1470 nm through 1610 nm, according to the wavelength indicated in the SFP's product ID

9 micron SMF

120 km (74.56 miles)

ONS-SE-622-1470 through ONS-SE-622-1610 (CWDM)

1470 nm through 1610 nm, according to the wavelength indicated in the SFP's product ID

9 micron SMF

100 km (62.14 miles)

ONS-SI-2G-I1

1310 nm

9 micron SMF

15 km (9.3 miles)

ONS-SI-2G-L1

1310 nm

9 micron SMF

40 km (25.80 miles)

ONS-SI-2G-L2

1550 nm

9 micron SMF

80 km (49.71 miles)

ONS-SI-2G-S1

1310 nm

9 micron SMF

2 km (1.2 miles)

ONS-SC-2G-30.3 through ONS-SC-2G-60.6 (DWDM)

1530.30 nm through 1560.60 nm, according to the wavelength indicated in the SFP's product ID

Note When using ONS-SC-2G-xx.x on CTX-2500 the Cisco ONS 15310-MA operating temperature specification is limited to -5 to +55 degrees Celsius (+23 to +131 degrees Fahrenheit).

9 micron SMF

N/A2

1 Typical loss on a 1310-nm wavelength SMF is 0.6 dB/km.

2 ONS-SC-2G-xx.x cable distance varies depending on DWDM system installation.