Object |
Value and function used to get the value |
mplsTunnelIndex |
At an endpoint, mplsTunnelIndex contains the source tunnel number. At a midpoint, the mplsTunnelIndex contains the source tunnel number for the forward LSP and the destination tunnel number for the reverse LSP. |
mplsTunnelInstance |
This contains the LSP number. The tp_get_tunnel_detail function is used to get this value. |
mplsTunnelIngressLSRId |
At an endpoint, this contains the value of mplsNodeConfigLocalId for the source of the tunnel. At a midpoint, it stores the mplsNodeConfigLocalId for the source of the tunnel for the forward LSP and mplsNodeConfigLocalId for the destination of the reverse LSP. This value ranges between 1 and 16777215. The tp_get_tunnel_detail function is used to get this value. |
mplsTunnelEgressLSRId |
At an endpoint, this contains the value of mplsNodeConfigLocalId for the destination node of the tunnel. At a midpoint, it stores the mplsNodeConfigLocalId for the destination of the tunnel for the forward LSP and mplsNodeConfigLocalId for the source of the tunnel for the reverse LSP. This value ranges between 1 and 16777215. The tp_get_tunnel_detail function is used to get this value. |
mplsTunnelName |
This contains the tunnel name, applicable at both endpoint and midpoint. The tp_get_tunnel_detail function is used to get this value. |
mplsTunnelDescr |
This contains the tunnel description. The tp_get_tunnel_detail function is used to get this value. |
mplsTunnelIsIf |
This is always true because the TP tunnel is always an interface. |
mplsTunnelIfIndex |
This contains the tunnel ifindex. The tp_get_tunnel_detail function provides the IF number. The interface number can be used to get the interface index. |
mplsTunnelOwner |
This is set to D_mplsTunnelOwner_other. |
mplsTunnelRole |
The tp_get_tunnel_detail function is used to get this value. |
mplsTunnelXCPointer |
The cfc_mpls_cp_lsrmib_rfc_make_XC_pointer function is used. |
mplsTunnelSignallingProto |
None(1). The MPLS TP implementation on Cisco IOS does not have a control plane and there is no signaling protocol. |
mplsTunnelSetupPrio |
0. By default, MPLS TP LSPs have 0 priority. |
mplsTunnelHoldingPrio |
0. By default, MPLS TP LSPs have 0 priority. |
mplsTunnelSessionAttributes |
N/A. 0. |
mplsTunnelLocalProtectInUse |
This object indicates whether a protected LSP is being used. The tp_get_tunnel_detail function is used to get this value. |
mplsTunnelResourcePointer |
0.0. Not supported. |
mplsTunnelPrimaryInstance |
This is used to indicate the LSP number of the working LSP. If the working LSP is not configured, then this shows a default value of 0. |
mplsTunnelInstancePriority |
N/A. 0. |
mplsTunnelHopTableIndex |
N/A. 0. |
mplsTunnelPathInUse |
N/A. 0. |
mplsTunnelARHopTableIndex |
N/A. 0. |
mplsTunnelCHopTableIndex |
N/A. 0. |
mplsTunnelIncludeAnyAffinity |
N/A. 0. |
mplsTunnelIncludeAllAffinity |
N/A. 0. |
mplsTunnelTotalUpTime |
The tp_get_tunnel_detail function is used to get this value. |
mplsTunnelInstanceUpTime |
The tp_get_tunnel_detail function is used to get this value. |
mplsTunnelPrimaryUpTime |
The tp_get_tunnel_detail function is used to get this value. |
mplsTunnelPathChanges |
N/A. 0. |
mplsTunnelLastPathChange |
N/A. |
mplsTunnelCreationTime |
The tp_get_tunnel_detail function is used to get this value. |
mplsTunnelStateTransitions |
N/A. 0. |
mplsTunnelAdminStatus |
At endpoint, the tp_get_tunnel_detail function is used to get this value. At midpoint, this is set to "testing(3)" as the TP does not maintain admin status at the midpoint. |
mplsTunnelOperStatus |
At endpoint, the tp_get_tunnel_detail function is used to get this value. At midpoint, this is set to "testing(3)" as the TP does not maintain oper status at the midpoint. |
mplsTunnelRowStatus |
D_mplsTunnelRowStatus_active |
mplsTunnelStorageType |
D_mplsTunnelStorageType_readOnly |
mplsTunnelPerfTable: This counter is not supported. |