IP Mobility: PMIPv6 Configuration Guide, Cisco IOS XE Release 3S
Proxy Mobile IPv6 Local Mobility Anchor
Downloads: This chapterpdf (PDF - 1.42MB) The complete bookPDF (PDF - 2.52MB) | Feedback

Proxy Mobile IPv6 Local Mobility Anchor

Contents

Proxy Mobile IPv6 Local Mobility Anchor

Local Mobility Anchor (LMA) acts as the home agent for a mobile node (MN) in a Proxy Mobile IPv6 domain, which is the network where the mobility management of an MN is handled using the Proxy Mobile IPv6 (PMIPv6) protocol. LMA is the topological anchor point for the MN’s home network prefix(es) and is the entity that manages the MN’s binding state. This module explains how to configure LMA.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for Proxy Mobile IPv6 LMA

You must configure the IPv4 and IPv6 address pool for LMA to assign IPv4 or IPv6 addresses.

Information About Proxy Mobile IPv6 Support for LMA Functionality

Proxy Mobile IPv6 Overview

Proxy Mobile IPv6 (PMIPv6) provides network-based IP Mobility management to a mobile node (MN), without requiring the participation of the MN in any IP mobility-related signaling. The mobility entities in the network track the movements of the MN, initiate the mobility signaling, and set up the required routing state.

The major functional entities of PMIPv6 are Mobile Access Gateways (MAGs), Local Mobility Anchors (LMAs), and MNs.

Mobile Access Gateways

A Mobile Access Gateway (MAG) performs mobility-related signaling on behalf of the mobile nodes (MN) attached to its access links. MAG is the access router for the MN; that is, the MAG is the first-hop router in the localized mobility management infrastructure.

A MAG performs the following functions:

  • Obtains an IP address from a Local Mobility Anchor (LMA) and assigns it to an MN
  • Retains the IP address of an MN when the MN roams across MAGs
  • Tunnels traffic from an MN to LMA

Local Mobility Anchor

Local Mobility Anchor (LMA) is the home agent for a mobile node (MN) in a Proxy Mobile IPv6 (PMIPv6) domain. It is the topological anchor point for MN home network prefixes and manages the binding state of an MN. An LMA has the functional capabilities of a home agent as defined in the Mobile IPv6 base specification (RFC 3775) along with the capabilities required for supporting the PMIPv6 protocol.


Note


Use an dynamic mag learning command to enable an LMA to accept Proxy Mobile IPv6 (PMIPv6) signaling messages from any Mobile Access Gateway (MAG) that is not locally configured.


Mobile Node

A mobile node (MN) is an IP host whose mobility is managed by the network. An MN can be an IPv4-only node, an IPv6-only node, or a dual-stack node, which is a node with IPv4 and IPv6 protocol stacks. An MN is not required to participate in any IP mobility-related signaling for achieving mobility for an IP address or a prefix that is obtained in the Proxy Mobile IPv6 (PMIPv6) domain.

AAA Server Attributes for Proxy Mobile IPv6

If an authentication, authorization, and accounting (AAA) server is available, a Mobile Access Gateway (MAG) obtains the profile information of the Proxy Mobile IPv6 (PMIPv6) domain and the mobile node (MN) from the server during the configuration and call-flow time, respectively.

The following are the AAA attributes required for configuring the PMIPv6 domain and the MN are:

  • PMIPv6 domain-specific AAA attributes:
    • cisco-mpc-protocol-interface
    • lma-identifier
    • mag-identifier
    • mag-v4-address
    • mag-v6-address
    • pmip6-domain-identifier
    • pmip6-timestamp-window
    • pmip6-replay-protection
    • pmip6-spi-key
    • pmip6-spi-value
  • MN-specific AAA attributes:
    • home-lma
    • home-lma-ipv6-address
    • mn-nai
    • home-lma-ipv4-address
    • mn-apn
    • Mobile-Node-Identifier
    • mn-network
    • mn-service
    • multihomed

How to Configure Proxy Mobile IPv6 LMA

Configuring a Proxy Mobile IPv6 Domain by Using the Configuration from the AAA Server

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    ipv6 mobile pmipv6-domain domain-name load-aaa

    4.    end


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Device> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.
     
    Step 2 configure terminal


    Example:
    Device# configure terminal
     

    Enters global configuration mode.

     
    Step 3 ipv6 mobile pmipv6-domain domain-name load-aaa


    Example:
    Device(config)# ipv6 mobile pmipv6-domain D1 load-aaa
     

    Creates a PMIPv6 domain and configures it by using the configuration from the AAA server.

     
    Step 4 end


    Example:
    Device(config)# end
     

    Exits global configuration mode and returns to privileged EXEC mode.

     

    Configuring a Minimum Configuration for a Domain When an AAA Server Is Not Available

    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    ipv6 mobile pmipv6-domain domain-name

      4.    mag mag-id

      5.    ipv4-address ipv4-address

      6.    ipv6-address ipv6-address

      7.    exit

      8.    Repeat Steps 4 to 7 to configure the second MAG.

      9.    nai [user]@realm

      10.    network network-name

      11.    service {dual | ipv4 | ipv6}

      12.    exit

      13.    Repeat Steps 8 to 12 to configure the second MN.

      14.    end


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 enable


      Example:
      Device> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.
       
      Step 2 configure terminal


      Example:
      Device# configure terminal
       

      Enters global configuration mode.

       
      Step 3 ipv6 mobile pmipv6-domain domain-name


      Example:
      Device(config)# ipv6 mobile pmipv6-domain dn1
       

      Creates the PMIP domain and enters PMIP domain configuration mode.

       
      Step 4 mag mag-id


      Example:
      Device(config-ipv6-pmipv6-domain)# mag mag1
       

      Configures a MAG within the PMIP domain and enters PMIP domain MAG configuration mode.

       
      Step 5 ipv4-address ipv4-address


      Example:
      Device(config-ipv6-pmipv6-domain-mag)# ipv4-address 192.0.2.254
       

      Configures an IPv4 address for the MAG within the PMIP domain.

       
      Step 6 ipv6-address ipv6-address


      Example:
      Device(config-ipv6-pmipv6-domain-mag)# ipv6-address 2001:DB8::1
       

      Configures an IPv6 address for the MAG within the PMIP domain.

       
      Step 7 exit


      Example:
      Device(config-ipv6-pmipv6-domain-mag)# exit
       

      Exits PMIP domain MAG configuration mode and returns to PMIP domain configuration mode.

       
      Step 8 Repeat Steps 4 to 7 to configure the second MAG.  

       
      Step 9 nai [user]@realm


      Example:
      Device(config-ipv6-pmipv6-domain)# nai example1@example.com
       

      Configures a network access identifier (NAI) for the MN within the PMIP domain and enters PMIP domain MN configuration mode.

       
      Step 10 network network-name


      Example:
      Device(config-ipv6-pmipv6-domain-mn)# network network1
       

      Associates a network name with the LMA under which an IPv4 or IPv6 pool can be enabled.

       
      Step 11 service {dual | ipv4 | ipv6}

      Example:
      Device(config-ipv6-pmipv6-domain-mn)# service ipv4
       

      Configures the service provided to the MN within the PMIP domain.

       
      Step 12 exit


      Example:
      Device(config-ipv6-pmipv6-domain-mn)# exit
       

      Exits PMIP domain MN configuration mode and returns to PMIP domain configuration mode.

       
      Step 13 Repeat Steps 8 to 12 to configure the second MN.  

       
      Step 14 end


      Example:
      Device(config-ipv6-pmipv6-domain)# end
       

      Exits PMIP domain configuration mode and returns to privileged EXEC mode.

       

      Configuring a Detailed Configuration for a Domain When the AAA Server Is Not Available

      SUMMARY STEPS

        1.    enable

        2.    configure terminal

        3.    ipv6 mobile pmipv6-domain domain-name

        4.    fixed-link-local-address ipv6-address

        5.    fixed-link-layer-address hardware-address

        6.    replay-protection timestamp [window seconds]

        7.    auth-option spi {spi-hex-value | decimal spi-decimal-value} key {ascii ascii-string | hex hex-string}

        8.    encap {gre-ipv4 | ipv6-in-ipv6}

        9.    local-routing-mag

        10.    mag mag-id

        11.    ipv4-address ipv4-address

        12.    ipv6-address ipv6-address

        13.    exit

        14.    Repeat Steps 10 to 13 to configure each MAG.

        15.    mag mag-id

        16.    ipv4-address ipv4-address

        17.    ipv6-address ipv6-address

        18.    exit

        19.    mn-profile-load-aaa

        20.    nai [user]@realm

        21.    lma lma-id

        22.    service {dual | ipv4 | ipv6}

        23.    network network-name

        24.    Repeat Steps 22 and 23 to configure each MN.

        25.    end


      DETAILED STEPS
         Command or ActionPurpose
        Step 1 enable


        Example:
        Device> enable
         

        Enables privileged EXEC mode.

        • Enter your password if prompted.
         
        Step 2 configure terminal


        Example:
        Device# configure terminal
         

        Enters global configuration mode.

         
        Step 3 ipv6 mobile pmipv6-domain domain-name


        Example:
        Device(config)# ipv6 mobile pmipv6-domain dn1
         

        Creates a PMIP domain and enters PMIPv6 domain configuration mode.

         
        Step 4 fixed-link-local-address ipv6-address


        Example:
        Router(config-ipv6-pmipv6-domain)# fixed-link-local-address FE80::CE00:BFF:FEFC:0
         

        Configures a fixed link-local address for the MAG-enabled interface toward the MN.

         
        Step 5 fixed-link-layer-address hardware-address


        Example:
        Router(config-ipv6-pmipv6-domain)# fixed-link-layer-address aaaa.bbbb.cccc
         

        Configures a fixed link layer address (Layer 2 address) for the MAG-enabled interface toward the MN.

         
        Step 6 replay-protection timestamp [window seconds]


        Example:
        Device(config-ipv6-pmipv6-domain)# replay-protection timestamp window 200
         

        Configures the replay protection mechanism within the PMIP domain.

         
        Step 7 auth-option spi {spi-hex-value | decimal spi-decimal-value} key {ascii ascii-string | hex hex-string}


        Example:
        Device(config-ipv6-pmipv6-domain)# auth-option spi 67 key ascii key1
         

        Configures authentication for the PMIP domain.

         
        Step 8 encap {gre-ipv4 | ipv6-in-ipv6}


        Example:
        Device(config-ipv6-pmipv6-domain)# encap gre-ipv4
         

        Configures the tunnel encapsulation mode type between the MAG and the LMA.

         
        Step 9 local-routing-mag


        Example:
        Device(config-ipv6-pmipv6-domain)# local-routing-mag
         

        Enables local routing for the MAG.

         
        Step 10 mag mag-id


        Example:
        Device(config-ipv6-pmipv6-domain)# mag mag1
         

        Configures MAG within the PMIP domain and enters PMIP domain MAG configuration mode.

         
        Step 11 ipv4-address ipv4-address


        Example:
        Device(config-ipv6-pmipv6-domain-mag)# ipv4-address 192.0.2.254
         

        Configures an IPv4 address for the MAG.

         
        Step 12 ipv6-address ipv6-address


        Example:
        Device(config-ipv6-pmipv6-domain-mag)# ipv6-address 2001:0DB8:2:3::1
         

        Configures an IPv6 address for the MAG.

         
        Step 13 exit


        Example:
        Device(config-ipv6-pmipv6-domain-mag)# exit
         

        Exits PMIP domain MAG configuration mode and returns to PMIP domain configuration mode.

         
        Step 14 Repeat Steps 10 to 13 to configure each MAG.  

         
        Step 15 mag mag-id


        Example:
        Device(config-ipv6-pmipv6-domain)# mag mag1
         

        Configures a MAG within the PMIP domain and enters PMIP domain MAG configuration mode.

         
        Step 16 ipv4-address ipv4-address


        Example:
        Device(config-ipv6-pmipv6-domain-mag)# ipv4-address 192.0.2.254
         

        Configures an IPv4 address for the MAG.

         
        Step 17 ipv6-address ipv6-address


        Example:
        Device(config-ipv6-pmipv6-domain-mag)# ipv6-address 2001:0DB8:2:4::2
         

        Configures an IPv6 address for the MAG.

         
        Step 18 exit


        Example:
        Device(config-ipv6-pmipv6-domain-mag)# exit
         

        Exits PMIP domain MAG configuration mode and returns to PMIP domain configuration mode.

         
        Step 19 mn-profile-load-aaa


        Example:
        Device(config-ipv6-pmipv6-domain)# mn-profile-load-aaa
         

        (Optional) Loads the profile configuration from the AAA server to the MN within the PMIP domain.

        Note   

        Steps 20 to 24 need not be executed if the MN is configured using the configuration from the AAA server. You can use the specific command to override the configuration for the specific MN parameter.

         
        Step 20 nai [user]@realm


        Example:
        Device(config-ipv6-pmipv6-domain)# nai example1@example.com
         

        Configures the NAI for the MN within the PMIP domain and enters PMIP domain MN configuration mode.

         
        Step 21 lma lma-id


        Example:
        Device(config-ipv6-pmipv6-domain-mn)# lma lma1
         

        Configures the LMA for the MN.

         
        Step 22 service {dual | ipv4 | ipv6}

        Example:
        Device(config-ipv6-pmipv6-domain-mn)# service ipv4
         

        Configures the service provided to the MN within the PMIP domain.

         
        Step 23 network network-name


        Example:
        Device(config-ipv6-pmipv6-domain-mn)# network network1
         

        Associates a network name with the LMA under which an IPv4 or IPv6 pool can be enabled.

         
        Step 24 Repeat Steps 22 and 23 to configure each MN.  

         
        Step 25 end


        Example:
        Device(config-ipv6-pmipv6-domain-mn)# end
         

        Exits PMIP domain MN configuration mode and returns to privileged EXEC mode.

         

        Configuring a Minimum Configuration for an LMA

        SUMMARY STEPS

          1.    enable

          2.    configure terminal

          3.    ip local pool pool-name low-ip-address high-ip-address

          4.    ipv6 local pool pool-name prefix/prefix-length assigned-length

          5.    ipv6 unicast-routing

          6.    ipv6 mobile pmipv6-lma lma-id domain domain-name

          7.    address ipv6 ipv6-address

          8.    network network1

          9.    pool ipv4 pool-name pfxlen number

          10.    pool ipv6 pool-name pfxlen number

          11.    exit

          12.    default profile profile-name

          13.    end


        DETAILED STEPS
           Command or ActionPurpose
          Step 1 enable


          Example:
          Device> enable
           

          Enables privileged EXEC mode.

          • Enter your password if prompted.
           
          Step 2 configure terminal


          Example:
          Device# configure terminal
           

          Enters global configuration mode.

           
          Step 3 ip local pool pool-name low-ip-address high-ip-address


          Example:
          Device(config)# ip local pool v4pool 172.16.23.1 172.16.23.10
           

          Creates a local pool of IPv4 addresses.

           
          Step 4 ipv6 local pool pool-name prefix/prefix-length assigned-length


          Example:
          Device(config)# ipv6 local pool v6pool 2001:0DB8::/29 64
           

          Creates a local pool of IPv6 addresses.

           
          Step 5 ipv6 unicast-routing


          Example:
          Device(config)# ipv6 unicast-routing
           

          Enables IPv6 routing.

           
          Step 6 ipv6 mobile pmipv6-lma lma-id domain domain-name


          Example:
          Device(config)# ipv6 mobile pmipv6-lma lma1 domain dn1
           

          Enables the LMA service on the router, configures the PMIP domain for the LMA, and enters LMA configuration mode.

           
          Step 7 address ipv6 ipv6-address


          Example:
          Device(config-ipv6-pmipv6-lma)# address ipv6 2001:DB8::1
           

          Configures an IPv6 address for the LMA.

           
          Step 8 network network1


          Example:
          Device(config-ipv6-pmipv6-lma)# network network1
           

          Associates a network, on which an IPv4 or IPv6 pool is configured, with the LMA, and enters LMA-network configuration mode.

           
          Step 9 pool ipv4 pool-name pfxlen number


          Example:
          Device(config-ipv6-pmipv6lma-network)# pool ipv4 v4pool pfxlen 24
           

          Specifies the name of the IPv4 address pool from which a home address is allocated to an MN subscriber.

           
          Step 10 pool ipv6 pool-name pfxlen number


          Example:
          Device(config-ipv6-pmipv6lma-network)# pool ipv6 v6pool pfxlen 24
           

          Specifies the name of the IPv6 address pool from which a home address is allocated to the MN subscriber.

           
          Step 11 exit


          Example:
          Device(config-ipv6-pmipv6lma-network)# exit
           

          Exits the LMA-network configuration mode and enters LMA configuration mode.

           
          Step 12 default profile profile-name


          Example:
          Device(config-ipv6-pmipv6-lma)# default profile profile1
           

          Enables the default profile for the MN.

           
          Step 13 end


          Example:
          Device(config-ipv6-pmipv6-lma)# end
           

          Exits LMA configuration mode and enters privileged EXEC mode.

           

          Configuring a Detailed Configuration for an LMA

          SUMMARY STEPS

            1.    enable

            2.    configure terminal

            3.    ip local pool pool-name low-ip-address high-ip-address

            4.    ipv6 local pool pool-name prefix/prefix-length assigned-length

            5.    ipv6 mobile pmipv6-lma lma-id domain domain-name

            6.    enable aaa accounting

            7.    network network-name

            8.    pool ipv4 pool-name pfxlen number

            9.    pool ipv6 pool-name pfxlen number

            10.    exit

            11.    default profile profile1

            12.    address ipv4 ipv4-address

            13.    address ipv6 ipv6-address

            14.    bce maximum number

            15.    bce lifetime seconds

            16.    bce refresh-time seconds

            17.    bce delete-wait-time seconds

            18.    replay-protection timestamp [window seconds]

            19.    bri delay min milliseconds

            20.    bri delay max milliseconds

            21.    bri retries number

            22.    mag mag-id domain-name

            23.    auth-option spi {spi-hex-value | decimal spi-decimal-value} key {ascii | hex} hex-string

            24.    ipv4-address ipv4-address

            25.    ipv6-address ipv6-address

            26.    encap {gre-ipv4 | ipv6-in-ipv6}

            27.    end

            28.    show ipv6 mobile pmipv6 lma lma1 globals


          DETAILED STEPS
             Command or ActionPurpose
            Step 1 enable


            Example:
            Device> enable
             

            Enables privileged EXEC mode.

            • Enter your password if prompted.
             
            Step 2 configure terminal


            Example:
            Device# configure terminal
             

            Enters global configuration mode.

             
            Step 3 ip local pool pool-name low-ip-address high-ip-address


            Example:
            Device(config)# ip local pool v4pool 172.16.23.1 172.16.23.10
             

            Creates a local pool of IPv4 addresses.

             
            Step 4 ipv6 local pool pool-name prefix/prefix-length assigned-length


            Example:
            Device(config)# ipv6 local pool v6pool 2001:0DB8::/29 64
             

            Creates a local pool of IPv6 addresses.

             
            Step 5 ipv6 mobile pmipv6-lma lma-id domain domain-name


            Example:
            Device(config)# ipv6 mobile pmipv6-lma lma1 domain dn1
             

            Enables the LMA service on a device, configures the PMIP domain for the LMA, and enters LMA configuration mode.

             
            Step 6 enable aaa accounting


            Example:
            Device(config-ipv6-pmipv6-lma)# enable aaa accounting
             

            Enables AAA accounting for MN sessions.

             
            Step 7 network network-name


            Example:
            Device(config-ipv6-pmipv6-lma)# network network1
             

            Configures a network name with the LMA under which an IPv4 or IPv6 pool is to be enabled and enters LMA-network configuration mode.

             
            Step 8 pool ipv4 pool-name pfxlen number


            Example:
            Device(config-ipv6-pmipv6lma-network)# pool ipv4 v4pool pfxlen 24
             

            Specifies the name of the IPv4 address pool from which a home address is allocated to an MN subscriber.

             
            Step 9 pool ipv6 pool-name pfxlen number


            Example:
            Device(config-ipv6-pmipv6lma-network)# pool ipv6 v6pool pfxlen 24
             

            Specifies the name of the IPv6 address pool from which a home address is allocated to an MN subscriber.

             
            Step 10 exit


            Example:
            Device(config-ipv6-pmipv6lma-network)# exit
             

            Exits LMA-network configuration mode and enters LMA configuration mode.

             
            Step 11 default profile profile1


            Example:
            Device(config-ipv6-pmipv6-lma)# default profile profile1
             

            Enables the default profile for the MN.

             
            Step 12 address ipv4 ipv4-address


            Example:
            Device(config-ipv6-pmipv6-lma)# address ipv4 192.0.2.1
             

            Configures an IPv4 address for the LMA.

             
            Step 13 address ipv6 ipv6-address


            Example:
            Device(config-ipv6-pmipv6-lma)# address ipv6 2001:DB8::1
             

            Configures an IPv6 address for the LMA.

             
            Step 14 bce maximum number


            Example:
            Device(config-ipv6-pmipv6-lma)# bce maximum 200
             

            Specifies the maximum number of Binding Cache Entries (BCE) that is allowed for the LMA on the MN.

             
            Step 15 bce lifetime seconds


            Example:
            Device(config-ipv6-pmipv6-lma)# bce lifetime 5000
             

            Specifies the maximum lifetime of a BCE on a MN.

             
            Step 16 bce refresh-time seconds


            Example:
            Device(config-ipv6-pmipv6-lma)# bce refresh-time 2000
             

            Specifies the time to refresh the BCE of an MN.

             
            Step 17 bce delete-wait-time seconds


            Example:
            Device(config-ipv6-pmipv6-lma)# bce delete-wait-time 2000
             

            Specify the minimum amount of time in seconds the LMA must wait before it deletes a BCE on receiving the notification from the MAG.

             
            Step 18 replay-protection timestamp [window seconds]


            Example:
            Device(config-ipv6-pmipv6-lma)# replay-protection timestamp window 200
             

            Configures the replay protection mechanism within the PMIP domain.

             
            Step 19 bri delay min milliseconds


            Example:
            Device(config-ipv6-pmipv6-lma)# bri delay min 500
             

            Specifies the minimum time for which an LMA should wait before transmitting the Binding Revocation Indication (BRI) message.

             
            Step 20 bri delay max milliseconds


            Example:
            Device(config-ipv6-pmipv6-lma)# bri delay max 4500
             

            Specifies the maximum time for which an LMA should wait for the Binding Revocation Acknowledgment (BRA) message before retransmitting the BRI message.

             
            Step 21 bri retries number


            Example:
            Device(config-ipv6-pmipv6-lma)# bri retries 6
             

            Specifies the maximum number of times an LMA should retransmit a BRI message until a BRA is received.

             
            Step 22 mag mag-id domain-name


            Example:
            Device(config-ipv6-pmipv6-lma)# mag mag3 dn1
             

            Configures the MAG for the LMA and enters LMA-MAG configuration mode.

             
            Step 23 auth-option spi {spi-hex-value | decimal spi-decimal-value} key {ascii | hex} hex-string


            Example:
            Device(config-ipv6-pmipv6lma-mag)# auth-option spi decimal 258 key hex FFFFF
             

            Configures authentication for the LMA within the MAG.

             
            Step 24 ipv4-address ipv4-address


            Example:
            Device(config-ipv6-pmipv6mag-lma)# ipv4-address 192.0.2.254
             

            Configures an IPv4 address for the LMA within the MAG.

             
            Step 25 ipv6-address ipv6-address


            Example:
            Device(config-ipv6-pmipv6mag-lma)# ipv6-address 2001:0DB8:2:5::1
             

            Configures an IPv6 address for the LMA within the MAG.

             
            Step 26 encap {gre-ipv4 | ipv6-in-ipv6}


            Example:
            Device(config-ipv6-pmipv6mag-lma)# encap gre-ipv4
             

            Configures a tunnel encapsulation mode type between the MAG and the LMA.

             
            Step 27 end


            Example:
            Device(config-ipv6-pmipv6mag-lma)# end
             

            Exits LMA-MAG configuration mode and returns to privileged EXEC mode.

             
            Step 28 show ipv6 mobile pmipv6 lma lma1 globals


            Example:
            Device# show ipv6 mobile pmipv6 lma lma1 globals
             

            (Optional) Displays LMA global configuration details.

             

            Example

            The following is sample output from the show ipv6 mobile lma globals command:

            Device# show ipv6 mobile pmipv6 lma lma1 globals
             
            ---------------------------------------------------
            Domain  : D1
            
            LMA Identifier                          :lma1
                    AAA Accounting                  : Disabled
                    Default MN Profile              : profile1
                    Network                         : network1
                    IPv4 Pool Name                  : v4
                    Prefix Length                   : 24
                    IPv6 Pool Name																		: v6pool
                    Prefix Length                   : 48
                    Max. HNPs                       : 1
                    Max Bindings                    : 128000
                    AuthOption                      : disabled
                    RegistrationLifeTime            : 3600 (sec)
                    DeleteTime                      : 10000 (msec)
                    CreateTime                      : 1500 (msec)
                    BRI InitDelayTime               : 1000 (msec)
                    BRI MaxDelayTime                : 2000 (msec)
                    BRI MaxRetries                  : 1
                    BRI EncapType                   : IPV6_IN_IPV6
                    Fixed Link address is           : enabled
                    Fixed Link address              : aaaa.aaaa.aaaa
                    Fixed Link Local address is     : enabled
                    Fixed Link local address        : 0xFE800000 0x0 0x0 0x2
                    RefreshTime                     : 300 (sec)
                    Refresh RetxInit time           : 1000 (msec)
                    Refresh RetxMax time            : 32000 (msec)
                    Timestamp option                : enabled
                    Validity Window                 : 10
            
            Peer :  mag1
                    Max. HNPs                       : 1
                    Max Bindings                    : 128000
                    AuthOption                      : disabled
                    RegistrationLifeTime            : 3600 (sec)
                    DeleteTime                      : 10000 (msec)
                    CreateTime                      : 1500 (msec)
                    BRI InitDelayTime               : 1000 (msec)
                    BRI MaxDelayTime                : 2000 (msec)
                    BRI MaxRetries                  : 1
                    BRI EncapType                   : IPV6_IN_IPV6
                    Fixed Link address is           : enabled
                    Fixed Link address              : aaaa.aaaa.aaaa
                    Fixed Link Local address is     : enabled
                    Fixed Link local address        : 0xFE800000 0x0 0x0 0x2
                    RefreshTime                     : 300 (sec)
                    Refresh RetxInit time           : 1000 (msec)
                    Refresh RetxMax time            : 32000 (msec)
                    Timestamp option                : enabled
                    Validity Window                 : 10
            
            Peer :  mag0
                    Max. HNPs                       : 1
                    Max Bindings                    : 128000
                    AuthOption                      : disabled
                    RegistrationLifeTime            : 3600 (sec)
                    DeleteTime                      : 10000 (msec)
                    CreateTime                      : 1500 (msec)
                    BRI InitDelayTime               : 1000 (msec)
                    BRI MaxDelayTime                : 2000 (msec)
                    BRI MaxRetries                  : 1
                    BRI EncapType                   : GRE in IPV4
                    Fixed Link address is           : enabled
                    Fixed Link address              : aaaa.aaaa.aaaa
                    Fixed Link Local address is     : enabled
                    Fixed Link local address        : 0xFE800000 0x0 0x0 0x2
                    RefreshTime                     : 300 (sec)
                    Refresh RetxInit time           : 1000 (msec)
                    Refresh RetxMax time            : 32000 (msec)
                    Timestamp option                : enabled
                    Validity Window                 : 10
            

            Troubleshooting Tips

            You can use the following commands to troubleshoot the LMA configuration:

            • debug ipv6 mobile lma event
            • debug ipv6 mobile lma info
            • show ipv6 pmipv6 lma bindings info
            • show ipv6 pmipv6 lma globals
            • show ipv6 pmipv6 lma tunnel

            Configuration Examples for Proxy Mobile IPv6 Support for LMA Functionality

            Example: Configuring a Proxy Mobile IPv6 Domain by Using the Configuration from the AAA Server

            The following example shows how to configure the PMIPv6 domain by using the AAA server configuration:

            Device# configure terminal
            Device(config)# ipv6 mobile pmipv6-domain D1 load-aaa
            

            The following example shows how to configure the PMIPv6 domain by using the configuration from the AAA server and how to override the configuration for specific PMIPv6 domain parameters:

            Device# configure terminal
            Device(config)# ipv6 mobile pmipv6-domain D11 load-aaa
            Device(config)# ipv6 mobile pmipv6-domain D11
            Device(config-ipv6-pmipv6-domain)# gre-ipv4
            Device(config-ipv6-pmipv6-domain)# auth-option spi 67 key ascii key1
            

            Example: Configuring a Minimum Configuration for a Domain When the Configuration from the AAA Server Is Not Available

            The following example shows how to configure a minimum configuration for a domain when the AAA server configuration is not available:

            Device# configure terminal
            Device(config)# ipv6 mobile pmipv6-domain D2
            Device(config-ipv6-pmipv6-domain)# replay-protection timestamp window 200
            Device(config-ipv6-pmipv6-domain)# auth-option spi 100 key ascii hi
            Device(config-ipv6-pmipv6-domain)# encap ipv6-in-ipv6
            !
            Device(config-ipv6-pmipv6-domain)# lma lma1
            Device(config-ipv6-pmipv6-domain-lma)# ipv4-address 10.1.1.1
            Device(config-ipv6-pmipv6-domain-lma)# ipv6-address 2001:0DB8:2:3::1
            Device(config-ipv6-pmipv6-domain-lma)# exit
            !
            Device(config-ipv6-pmipv6-domain)# mag mag1
            Device(config-ipv6-pmipv6-domain-mag)# ipv4-address 10.1.3.1
            Device(config-ipv6-pmipv6-domain-mag)# ipv6-address 2001:0DB8:2:5::1
            Device(config-ipv6-pmipv6-domain-mag)# exit
            !
            Device(config-ipv6-pmipv6-domain)# nai example@example.com
            Device(config-ipv6-pmipv6-domain-mn)# lma lma1
            Device(config-ipv6-pmipv6-domain-mn)# int att GigabitETHERNET l2-addr 02c7.f800.0422
            Device(config-ipv6-pmipv6-domain-mn)# gre-encap-key up 1234
            Device(config-ipv6-pmipv6-domain-mn)# gre-encap-key down 5678
            Device(config-ipv6-pmipv6-domain-mn)# service ipv4
            Device(config-ipv6-pmipv6-domain-mn)# network-name example1
            Device(config-ipv6-pmipv6-domain-mn)# end
            

            Example: Configuring an LMA

            The following example shows the minimum configuration required to enable LMA:

            Device# configure terminal
            Device(config)# ipv6 mobile pmipv6-domain D2
            !
            Device(config-ipv6-pmipv6-domain)# lma lma1
            Device(config-ipv6-pmipv6-domain-lma)# ipv4-address 10.1.1.1
            Device(config-ipv6-pmipv6-domain-lma)# ipv6-address 2001:0DB8:2:3::1
            Device(config-ipv6-pmipv6-domain-lma)# exit
            !
            Device(config-ipv6-pmipv6-domain)# lma lma2
            Device(config-ipv6-pmipv6-domain-lma)# ipv4-address 10.2.1.1
            Device(config-ipv6-pmipv6-domain-lma)# ipv6-address 2001:0DB8:2:4::1
            Device(config-ipv6-pmipv6-domain-lma)# exit
            !
            Device(config-ipv6-pmipv6-domain)# nai example1@example.com
            Device(config-ipv6-pmipv6-domain-mn)# network-name example1
            Device(config-ipv6-pmipv6-domain-mn)# exit
            !
            Device(config-ipv6-pmipv6-domain)# nai example2@example.com
            Device(config-ipv6-pmipv6-domain-mn)# network-name example1
            Device(config-ipv6-pmipv6-domain-mn)# exit
            !
            Device(config)# ipv6 mobile pmipv6-lma lma1 domain D2
            Device(config-ipv6-pmipv6-lma)# address ipv6 2001:DB8:0:0:E000::F
            Device(config-ipv6-pmipv6-lma)# address ipv4 10.2.1.1
            Device(config-ipv6-pmipv6-domain-mn)# network-name example1
            Device(config-ipv6-pmipv6lma-network)# pool ipv4 v4pool pfxlen number
            Device(config-ipv6-pmipv6lma-network)# pool ipv6 v6pool pfxlen number
            Device(config-ipv6-pmipv6lma-network)# exit
            Device(config-ipv6-pmipv6-lma)# default profile example2@example.com
             
            Device(ipv6-mag-config)# exit
            

            Where to Go Next

            The MAG entity works with the LMA provided by the ASR 5000 devices. To configure the LMA in the Cisco ASR 5000, see the “PDN Gateway Configuration” module in the Cisco ASR 5000 Series Packet Data Network Gateway Administration Guide.

            Additional References

            Related Documents

            Related Topic

            Document Title

            Cisco IOS commands

            Master Command List, All Releases

            IP mobility commands

            IP Mobility Command Reference

            Standards and RFCs

            Standard/RFC

            Title

            RFC 3775

            Mobility Support in IPv6

            RFC 5213

            Proxy Mobile IPv6

            RFC 5844

            IPv4 Support for Proxy Mobile IPv6

            RFC 5845

            Generic Routing Encapsulation (GRE) Key Option for Proxy Mobile IPv6

            RFC 5846

            Binding Revocation for IPv6 Mobility

            MIBs

            MIB

            MIBs Link

            None

            To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL:

            http:/​/​www.cisco.com/​go/​mibs

            Technical Assistance

            Description

            Link

            The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

            http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

            Feature Information for PMIP - Mobile Router Support

            The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

            Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

            Table 1 Feature Information for PMIP - Mobile Router Support

            Feature Name

            Releases

            Feature Information

            PMIP - Mobile Router Support

            15.4(1)T

            PMIP - Mobile Router support feature enables the mobility of a node that is device comprising of one or more entire networks moving together, for example, on an airplane, a ship, a train, an automobile, a bicycle, or a kayak. The nodes connected to a network served by the mobile device may themselves be fixed nodes or mobile nodes or devices.