Step 1 |
enable
Example:
|
Enables privileged EXEC mode.
|
Step 2 |
configure
terminal
Example:
Device# configure terminal
|
Enters global configuration mode.
|
Step 3 |
ip
sla
operation-number
Example:
Device(config)# ip sla 10
|
Begins configuration for an IP SLAs operation and enters IP SLA configuration mode.
|
Step 4 |
udp-jitter
{destination-ip-address |
destination-hostname}
destination-port
endpoint-list
endpoint-list [ssm]
[source-ip
ip-address] [source-port
port-number] [num-packets
number-of-packets] [interval
interpacket-interval]
Example:
Device(config-ip-sla)# udp-jitter 239.1.1.1 5000 endpoint-list mcast-rcvrs source-ip 10.10.10.106 source-port 7012 num-packets 50 interval 25
|
Configures the IP SLAs operation as a multicast UDP jitter operation and enters multicast UDP jitter configuration mode.
|
Step 5 | control retry
retries
Example:
Device(config-ip-sla-multicast-jitter-oper)# control retry 2
| (Optional) Configures the number of times a sending device will resend a control protocol message.
|
Step 6 | control timeout
seconds
Example:
Device(config-ip-sla-multicast-jitter)# control timeout 4
| (Optional) Configures the number of seconds that the destination device will wait for a control protocol message.
|
Step 7 | dscp
dscp-value
Example:
Device(config-ip-sla-multicast-jitter-oper)# dscp 10
| (Optional) Configures the DSCP value for the operation.
|
Step 8 | tree-init
number
Example:
Device(config-ip-sla-multicast-jitter-oper)# tree-init 1
| (Optional) Sets up the multicast tree.
|
Step 9 |
history
distributions-of-statistics-kept
size
Example:
Device(config-ip-sla-multicast-jitter-oper)# history distributions-of-statistics-kept 5
|
(Optional) Sets the number of statistics distributions kept per hop during an IP SLAs operation.
|
Step 10 |
history
enhanced
[interval
seconds] [buckets
number-of-buckets]
Example:
Device(config-ip-sla-multicast-jitter-oper)# history enhanced interval 900 buckets 100
|
(Optional) Enables enhanced history gathering for an IP SLAs operation.
|
Step 11 |
frequency
seconds
Example:
Device(config-ip-sla-multicast-jitter-oper)# frequency 30
|
(Optional) Sets the rate at which a specified IP SLAs operation repeats.
|
Step 12 |
history
hours-of-statistics-kept
hours
Example:
Device(config-ip-sla-multicast-jitter-oper)# history hours-of-statistics-kept 4
|
(Optional) Sets the number of hours for which statistics are maintained for an IP SLAs operation.
|
Step 13 |
owner
owner-id
Example:
Device(config-ip-sla-multicast-jitter-oper)# owner admin
|
(Optional) Configures the Simple Network Management Protocol (SNMP) owner of an IP SLAs operation.
|
Step 14 |
request-data-size
bytes
Example:
Device(config-ip-sla-multicast-jitter-oper)# request-data-size 64
|
(Optional) Sets the protocol data size in the payload of an IP SLAs operation's request packet.
|
Step 15 |
history
statistics-distribution-interval
milliseconds
Example:
Device(config-ip-sla-multicast-jitter-oper)# history statistics-distribution-interval 10
|
(Optional) Sets the time interval for each statistics distribution kept for an IP SLAs operation.
|
Step 16 |
tag
text
Example:
Device(config-ip-sla-multicast-jitter-oper)# tag TelnetPollServer1
|
(Optional) Creates a user-specified identifier for an IP SLAs operation.
|
Step 17 |
threshold
milliseconds
Example:
Device(config-ip-sla-multicast-jitter-oper)# threshold 10000
|
(Optional) Sets the upper threshold value for calculating network monitoring statistics created by an IP SLAs operation.
|
Step 18 |
timeout
milliseconds
Example:
Device(config-ip-sla-multicast-jitter-oper)# timeout 10000
|
(Optional) Sets the amount of time an IP SLAs operation waits for a response from its request packet.
|
Step 19 |
tos
number
Example:
Device(config-ip-sla-multicast-jitter-oper)# tos 160
|
(Optional) In an IPv4 network only, defines the ToS byte in the IPv4 header of an IP SLAs operation.
|
Step 20 |
verify-data
Example:
Device(config-ip-sla-multicast-jitter-oper)# verify-data
|
(Optional) Causes an IP SLAs operation to check each reply packet for data corruption.
|
Step 21 |
vrf
vrf-name
Example:
Device(config-ip-sla-multicast-jitter-oper)# vrf vpn-A
|
(Optional) Allows monitoring within Multiprotocol Label Switching (MPLS) VPNs using IP SLAs operations.
|
Step 22 |
end
Example:
Device(config-ip-sla-multicast-jitter-oper)# end
|
Returns to privileged EXEC mode.
|
Step 23 |
show
ip
sla
configuration
[operation-number]
Example:
Device# show ip sla configuration 10
|
(Optional) Displays configuration values including all defaults for all IP SLAs operations or a specified operation.
|