The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This module provides instructions for upgrading Cisco StadiumVision Mobile Reporter or Cisco StadiumVision Mobile Streamer software on both the Cisco UCS C220 and Cisco UCS C200 servers, and contains the following sections:
•Set the User Time Zone—Cisco StadiumVision Mobile Reporter
•Upgrading Cisco StadiumVision Mobile Software
The Cisco StadiumVision Mobile Reporter has the default users marketing and admin, and a default time zone setting of Pacific Standard Time (PST). If the user browser or device is set to Pacific Standard Time (PST) and if the events are occurring in the EST time zone, the user can change the reports timestamp to the Eastern Standard Time (EST) time zone.
Each user time zone can be changed by using the following procedure:
Note Access to the Cisco StadiumVision Mobile Reporter CLI requires administrator access.
Step 1 SSH to the Cisco StadiumVision Mobile Reporter.
Step 2 Execute the cassandra-cli shell command.
Step 3 Within the CLI console, execute the following commands:
a. use BDASchema;
b. set Users['marketing']['gmtoffset']='-8';
c. set Users['admin']['gmtoffset']='-8';
`-8' can be changed according to the desired time zone offset listed in Table 1.
Table 1
Time Zones and Offsets
Before upgrading, perform the following actions:
•Download the upgrade ISO from http://software.cisco.com/download/navigator.html?mdfid=283479662&i=rm
Cisco StadiumVision Mobile Streamer
–1.2 to 1.3: SVM-STREAM-UPGRADE-1.3.0-xxx.x86_64_FOR-1.2.iso
–1.3 to 1.3+: SVM-STREAM-UPGRADE-1.3.0-xxx.x86_64.iso
Cisco StadiumVision Mobile Reporter
–1.2 to 1.3, or 1.3 to 1.3+: SVM-REPORT-UPGRADE-1.3.0-xxx.x86_64.iso
Note If Cisco StadiumVision Mobile Streamer Release 1.1 was previously installed and upgraded to Release 1.2 (using a Cisco StadiumVision Mobile Streamer Release 1.2 upgrade RPM), you will need to install a full ISO to upgrade to Release 1.3.
Possible sudo file corruption may result if a Cisco StadiumVision Mobile Streamer Release 1.3 upgrade ISO is used.
When using a Cisco UCS C220 server, observe the following guidelines before starting the upgrade:
•Do **not** alter the RAID configuration prior to upgrading
•Verify the boot order in the BIOS (by pressing F2 while booting) prior to upgrading; the virtual DVD should be the primary boot device
The Cisco StadiumVision Mobile Reporter releases 1.2 and later, and Cisco StadiumVision Mobile Streamer releases 1.3 and later can be upgraded using a combination of the web browser user interface, and the TUI.
To upgrade Cisco StadiumVision Mobile software, use the following procedure:
Step 1 Navigate to the ISO Updater in a web browser, using the following address:
ip address/cgi-bin/isoupload.cgi
Step 2 Click on the Choose File button, navigate to the ISO file, and click the Upload ISO button.
The ISO image is copied to the hard drive.
Step 3 Access the TUI, using the procedure in the
Step 4 Navigate to the server upgrade option.
Step 5 Choose the desired software upgrade from the list and press enter.
The server begins the upgrade process.
To upgrade the Cisco StadiumVision Mobile Streamer, release 1.2:
•Cisco UCS C220: mount the appropriate ISO image via CIMC and boot from the virtual optical drive, using the instructions in the
•Cisco UCS C200: Burn the appropriate ISO image to a DVD and boot from the optical drive using the procedures in the
Step 6