Guest

Cisco 2600 Series Multiservice Platforms

Voice Hardware Compatibility Matrix (Cisco 17/26/28/36/37/38xx, VG200, Catalyst 4500/4000, Catalyst 6xxx)

Cisco - Voice Hardware Compatibility Matrix (Cisco 17/26/28/36/37/38xx, VG200, Catalyst 4500/4000, Catalyst 6xxx)

Document ID: 5111

Updated: Jul 31, 2008

   Print

Introduction

This document describes the relationship between routers, gateways, Cisco Catalyst switches, and voice network modules and cards.

Prerequisites

Requirements

There are no specific requirements for this document.

Components Used

Conventions

Refer to Cisco Technical Tips Conventions for more information on document conventions.

Voice Hardware Compatibility Overview

The three tables in this section show the relationship between routers, gateways, Catalyst switches, and voice network modules and cards:

Router Model (right) 1721 1750 1751 1760
Voice Interface Card (VIC) (below)
NM-1V 1, NM-2V 1 No No No
NM-HDV No No No
NM-HDA-4FXS, EM-HDA-4FXO, EM-HDA-8FXS No No No
MRP No No No
NM-HDV-FARM No No No
NM-HDV2 No No No
NM-HD-1V, NM-HD-2V, NM-HD-2VE 2 No No No
EVM-HD-8FXS/DID, EM-4BRI-NT/TE, EM-HDA-8FXS, EM-HDA-6FXO, EM-HDA-3FXS/4FXO No No No
Voice Advanced Integration Module (AIM-VOICE) No No No
Voice WAN Interface Cards (VWICs) without Network Modules Yes No Yes
VICs without Network Modules No Yes Yes
Switch Model Support Features
Catalyst 4500/4000 Access Gateway Module WAN Interface Cards (WICs), VICs, Digital Signal Processors (DSPs), and IP phone inline power cards
Catalyst 6500/6000 T1/E1 trunk modules, Foreign Exchange Station (FXS) modules, IP phone inline power cards, and the Communications Media Module

  • 1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:

    • Trunked ATM Adaptation Layer 2 (AAL2) on analog ports

    • Universal Foreign Exchange Office (FXO) (VIC2-xFXO) voice cards with software-selectable Centralized Automated Message Accounting (CAMA)

    • Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/Direct Inward Dial (DID) cards

    • The drop of DSPs on a Plain Old Telephone Service (POTS)-to-POTS call that stays within the network module

  • 2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:

    • Modem relay

    There is support for the G.168 echo cancellation (ECAN) in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.

Router Model (right) VG200 3 261x, 2x, 5x 2600XM 2691 2801 4 2811, 2821, 2851
VIC (below)
NM-1V 1, NM-2V 1 Yes Yes Yes Yes No No
NM-HDV Yes Yes Yes Yes No Yes
NM-HDA-4FXS, EM-HDA-4FXO, EM-HDA-8FXS No Yes Yes Yes No Yes
MRP No No No No No No
NM-HDV-FARM Yes Yes5 Yes Yes No Yes
NM-HDV2 No No Yes Yes No Yes
NM-HD-1V, NM-HD-2V, NM-HD-2VE 2 No No Yes Yes No Yes
EVM-HD-8FXS/DID, EM-4BRI-NT/TE, EM-HDA-8FXS, EM-HDA-6FXO, EM-HDA-3FXS/4FXO No No No No No Yes6
Voice Advanced Integration Module (AIM-VOICE) No Yes Yes Yes No No
VWICs without Network Modules No Yes7 Yes7 Yes7 Yes Yes
VICs without Network Modules No No No No Yes Yes
Switch Model Support Features
Catalyst 4500/4000 Access Gateway Module WICs, VICs, DSPs, and IP phone inline power cards
Catalyst 6500/6000 T1/E1 trunk modules, FXS modules, IP phone inline power cards, and the Communications Media Module

  • 1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:

    • Trunked ATM Adaptation Layer 2 (AAL2) on analog ports

    • Universal Foreign Exchange Office (FXO) (VIC2-xFXO) voice cards with software-selectable Centralized Automated Message Accounting (CAMA)

    • Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/Direct Inward Dial (DID) cards

    • The drop of DSPs on a Plain Old Telephone Service (POTS)-to-POTS call that stays within the network module

  • 2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:

    • Modem relay

    There is support for the G.168 echo cancellation (ECAN) in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.

  • 3These products have reached end of sale. Refer to the End-of-Sale Announcement for the Cisco VG200 Access Gateway.

  • 4 Slot 0 in 2801 can only be configured for voice, which means that PRI configurations with VWIC are not possible. However, configuration for channel associated signaling (CAS) is possible.

  • 5There is support on the Cisco 2650 and 2651, but not on the 261x and 262x.

  • 6Only the Cisco 2821 and 2851 models support the EVM-HD-8FXS/DID.

  • 7VWICs without network modules have support on these platforms only if you have installed AIM-VOICE-30 or AIM-ATM-VOICE-30.

Router Model (right) ICS 7750 3620 3640/40A 3660 37xx 3825, 3845
VIC (below)
NM-1V 1, NM-2V 1 No Yes Yes Yes Yes No
NM-HDV No Yes Yes Yes Yes Yes
NM-HDA-4FXS, EM-HDA-4FXO, EM-HDA-8FXS No No Yes Yes Yes Yes
MRP Yes No No No No No
NM-HDV-FARM No No Yes Yes Yes Yes
NM-HDV2 No No No No Yes Yes
NM-HD-1V, NM-HD-2V, NM-HD-2VE 2 No No Yes Yes Yes Yes
EVM-HD-8FXS/DID, EM-4BRI-NT/TE, EM-HDA-8FXS, EM-HDA-6FXO, EM-HDA-3FXS/4FXO No No No No No Yes
Voice Advanced Integration Module (AIM-VOICE) No No No Yes3 Yes No
VWICs without Network Modules Yes No No No Yes4 Yes
VICs without Network Modules Yes No No No No Yes
Switch Model Support Features
Catalyst 4500/4000 Access Gateway Module WICs, VICs, DSPs, and IP phone inline power cards
Catalyst 6500/6000 T1/E1 trunk modules, FXS modules, IP phone inline power cards, and the Communications Media Module

  • 1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:

    • Trunked ATM Adaptation Layer 2 (AAL2) on analog ports

    • Universal Foreign Exchange Office (FXO) (VIC2-xFXO) voice cards with software-selectable Centralized Automated Message Accounting (CAMA)

    • Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/Direct Inward Dial (DID) cards

    • The drop of DSPs on a Plain Old Telephone Service (POTS)-to-POTS call that stays within the network module

  • 2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:

    • Modem relay

    There is support for the G.168 echo cancellation (ECAN) in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.

  • 3On the Cisco 3660, the AIM-VOICE-30 and AIM-ATM-VOICE-30 products only have support when there is also a multiservice interchange (MIX) daughter card installed.

  • 4VWICs without network modules have support on these platforms only if you have installed AIM-VOICE-30 or AIM-ATM-VOICE-30.

Cisco 17xx, VG200, 26xx, and 2800 Platforms Matrix

The three tables in this section show the router or gateway models that support the voice network modules and the VICs. For more information on the modules and cards, which includes Cisco IOS Software support, click the link for the appropriate module or card.

Routers/Gateways
Model 1721 1750 1751, 1760 VG200 1
Voice Network Module (right) Not Used Not Used Not Used NM-1V 2 NM-2V 2 NM- HDV
VIC (below)
VIC-2FXO, EU No Yes Yes Yes No
VIC-2FXO-M1/M2/M3 No Yes Yes Yes No
VIC-2FXS No Yes Yes Yes No
VIC-2E/M No Yes Yes Yes No
VIC-2BRI-S/T-TE No No No Yes No
VIC-2BRI-NT/TE No No Yes No No
VIC-2DID No No Yes Yes No
VIC-2CAMA No No No No No
VIC-1J1 No No No No No
VIC-4FXO-M1 No No No No No
VIC-4FXS/DID No No Yes No No
VIC2-4FXO (FXO/CAMA) No No Yes No No
VIC2-2FXO (FXO/CAMA) No No Yes No No
VIC2-2FXS No No Yes No No
VIC2-2E/M No No Yes No No
VIC2-2BRI- NT/TE No No Yes No No
VWIC-xMFT-E1 (with or without drop and insert [DI]) Yes3 No Yes No Yes
VWIC-1MFT-G703 Yes3 No Yes No No
VWIC-2MFT-G703 Yes3 No Yes No Yes
VWIC-xMFT-T1 (with or without DI) Yes3 No Yes No Yes

Note: 

  • 1These products have reached end of sale. Refer to the End-of-Sale Announcement for the Cisco VG200 Access Gateway.

  • 2The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:

    • Trunked AAL2 on analog ports

    • Universal FXO (VIC2-xFXO) voice cards with software-selectable CAMA

    • Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/DID cards

    • The drop of DSPs on a POTS-to-POTS call that stays within the network module

  • 3This configuration supports data applications only.

Routers/Gateways
Model 261x, 2x, 5x 2600XM, 2691
Voice Network Module (right) NM-1V 1 NM-2V 1 NM- HDV NM-1V 1 NM-2V 1 NM-HD-1V 1 NM-HD-2V 1 NM-HD-2VE 2 NM- HDV NM- HDV2
VIC (below)
VIC-2FXO, EU Yes No Yes No No No No
VIC-2FXO-M1/M2/M3 Yes No Yes No No No No
VIC-2FXS Yes No Yes No No No No
VIC-2E/M Yes No Yes No No No No
VIC-2BRI-S/T-TE Yes No Yes No No No No
VIC-2BRI-NT/TE Yes No Yes No No No No
VIC-2DID Yes No Yes Yes Yes No Yes
VIC-2CAMA Yes No Yes No No No No
VIC-1J1 No Yes No No No Yes Yes
VIC-4FXO-M1 No No No No No No No
VIC-4FXS/DID No No No Yes3 Yes3 No Yes3
VIC2-4FXO (FXO/CAMA) No No No Yes Yes No Yes
VIC2-2FXO (FXO/CAMA) No No No Yes Yes No Yes
VIC2-2FXS No No No Yes Yes No Yes
VIC2-2E/M No No No Yes Yes No Yes
VIC2-2BRI- NT/TE No No No Yes Yes No Yes
VWIC-xMFT-E1 (with or without DI) No Yes No No Yes Yes Yes
VWIC-1MFT-G703 No No No No No No Yes
VWIC-2MFT-G703 No Yes No No No Yes Yes
VWIC-xMFT-T1 (with or without DI) No Yes No No Yes Yes Yes

Note: 

  • 1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:

    • Trunked AAL2 on analog ports

    • Universal FXO (VIC2-xFXO) voice cards with software-selectable CAMA

    • Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/DID cards

    • The drop of DSPs on a POTS-to-POTS call that stays within the network module

  • 2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:

    • Modem relay

    There is support for the G.168 ECAN in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.

  • 3On this platform series and network module type, the VIC-4FXS/DID card currently does not support the DID mode of operation. The voice ports only operate as FXS interfaces. Support for both modes of operation will be available in Cisco IOS Software Release 12.3(14)T. If analog DID is necessary at this time, use the VIC-2DID product instead.

Routers/Gateways
Model 2801 2811, 2821, 2851
Voice Network Module (right) Not Used NM-HD-1V 1 NM-HD-2V 1 NM-HD-2VE 2 NM- HDV NM- HDV2 Chassis slot
VIC (below)
VIC-2FXO, EU No No No No No No
VIC-2FXO-M1/M2/M3 No No No No No No
VIC-2FXS No No No No No No
VIC-2E/M No No No No No No
VIC-2BRI-S/T-TE No No No No No No
VIC-2BRI-NT/TE No No No No No No
VIC-2DID Yes Yes Yes No Yes Yes
VIC-2CAMA No No No No No No
VIC-1J1 No No No Yes Yes No
VIC-4FXO-M1 No No No No No No
VIC-4FXS/DID Yes Yes3 Yes3 No Yes3 Yes3
VIC2-4FXO (FXO/CAMA) Yes Yes Yes No Yes Yes
VIC2-2FXO (FXO/CAMA) Yes Yes Yes No Yes Yes
VIC2-2FXS Yes Yes Yes No Yes Yes
VIC2-2E/M Yes Yes Yes No Yes Yes
VIC2-2BRI- NT/TE Yes Yes Yes No Yes Yes
VWIC-xMFT-E1 (with or without DI) Yes No Yes Yes Yes Yes
VWIC-1MFT-G703 Yes No No No Yes Yes
VWIC-2MFT-G703 Yes No No Yes Yes Yes
VWIC-xMFT-T1 (with or without DI) Yes No Yes Yes Yes Yes

Note: 

  • 1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:

    • Trunked AAL2 on analog ports

    • Universal FXO (VIC2-xFXO) voice cards with software-selectable CAMA

    • Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/DID cards

    • The drop of DSPs on a POTS-to-POTS call that stays within the network module

  • 2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:

    • Modem relay

    There is support for the G.168 ECAN in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.

  • 3On this platform series and network module type, the VIC-4FXS/DID card currently does not support the DID mode of operation. The voice ports only operate as FXS interfaces. Support for both modes of operation will be available in Cisco IOS Software Release 12.3(14)T. If analog DID is necessary at this time, use the VIC-2DID product instead.

Cisco ICS 7750, 36xx, 37xx, and 38xx Platforms Matrix

Routers/Gateways
Model ICS 7750 3620 3640/40A, 3660
Voice Network Module (right) MRP NM-1V 1 NM-2V 1 NM-HDV NM-1V 1 NM-2V 1 NM-HD-1V 1 NM-HD-2V 1 NM-HD-2VE 2 NM- HDV
VIC (below)
VIC-2FXO, EU No Yes No Yes No No No
VIC-2FXO-M1/M2/M3 Yes Yes No Yes No No No
VIC-2FXS Yes Yes No Yes No No No
VIC-2E/M Yes Yes No Yes No No No
VIC-2BRI-S/T-TE No Yes No Yes No No No
VIC-2BRI-NT/TE Yes Yes No Yes No No No
VIC-2DID Yes Yes No Yes Yes Yes No
VIC-2CAMA No Yes No Yes No No No
VIC-1J1 No No Yes No No No Yes
VIC-4FXO-M1 Yes No No No No No No
VIC-4FXS/DID Yes No No No Yes3 Yes3 No
VIC2-4FXO (FXO/CAMA) Yes No No No Yes Yes No
VIC2-2FXO (FXO/CAMA) No No No No Yes Yes No
VIC2-2FXS No No No No Yes Yes No
VIC2-2E/M Yes No No No Yes Yes No
VIC2-2BRI- NT/TE Yes No No No Yes Yes No
VWIC-xMFT-E1 (with or without DI) Yes4 No Yes No No Yes Yes
VWIC-1MFT-G703 No No No No No No No
VWIC-2MFT-G703 No No Yes No No No Yes
VWIC-xMFT-T1 (with or without DI) Yes4 No Yes No No Yes Yes

Note: 

  • 1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:

    • Trunked AAL2 on analog ports

    • Universal FXO (VIC2-xFXO) voice cards with software-selectable CAMA

    • Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/DID cards

    • The drop of DSPs on a POTS-to-POTS call that stays within the network module

  • 2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:

    • Modem relay

    There is support for the G.168 ECAN in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.

  • 3On this platform series and network module type, the VIC-4FXS/DID card currently does not support the DID mode of operation. The voice ports only operate as FXS interfaces. Support for both modes of operation will be available in Cisco IOS Software Release 12.3(14)T. If analog DID is necessary at this time, use the VIC-2DID product instead.

  • 4The ICS 7750 does not support VWIC-2MFT-T1-DI and VWIC-2MFT-E1-DI cards with DI.

Routers/Gateways
Model 37xx
Voice Network Module (right) NM-1V 1 NM-2V 1 NM-HD-1V 1 NM-HD-2V 1 NM-HD-2VE 2 NM- HDV NM- HDV2
VIC (below)
VIC-2FXO, EU Yes No No No No
VIC-2FXO-M1/M2/M3 Yes No No No No
VIC-2FXS Yes No No No No
VIC-2E/M Yes No No No No
VIC-2BRI-S/T-TE Yes No No No No
VIC-2BRI-NT/TE Yes No No No No
VIC-2DID Yes Yes Yes No Yes
VIC-2CAMA Yes No No No No
VIC-1J1 No No No Yes Yes
VIC-4FXO-M1 No No No No No
VIC-4FXS/DID No Yes3 Yes3 No Yes3
VIC2-4FXO (FXO/CAMA) No Yes Yes No Yes
VIC2-2FXO (FXO/CAMA) No Yes Yes No Yes
VIC2-2FXS No Yes Yes No Yes
VIC2-2E/M No Yes Yes No Yes
VIC2-2BRI- NT/TE No Yes Yes No Yes
VWIC-xMFT-E1 (with or without DI) No No Yes Yes Yes
VWIC-1MFT-G703 No No No No Yes
VWIC-2MFT-G703 No No No Yes Yes
VWIC-xMFT-T1 (with or without DI) No No Yes Yes Yes

Note: 

  • 1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:

    • Trunked AAL2 on analog ports

    • Universal FXO (VIC2-xFXO) voice cards with software-selectable CAMA

    • Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/DID cards

    • The drop of DSPs on a POTS-to-POTS call that stays within the network module

  • 2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:

    • Modem relay

    There is support for the G.168 ECAN in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.

  • 3On this platform series and network module type, the VIC-4FXS/DID card currently does not support the DID mode of operation. The voice ports only operate as FXS interfaces. Support for both modes of operation will be available in Cisco IOS Software Release 12.3(14)T. If analog DID is necessary at this time, use the VIC-2DID product instead.

Routers/Gateways
Model 3825, 3845
Voice Network Module (right) NM-HD-1V 1 NM-HD-2V 1 NM-HD-2VE 2 NM- HDV NM- HDV2 Chassis slot
VIC (below)
VIC-2FXO, EU No No No No No
VIC-2FXO-M1/M2/M3 No No No No No
VIC-2FXS No No No No No
VIC-2E/M No No No No No
VIC-2BRI-S/T-TE No No No No No
VIC-2BRI-NT/TE No No No No No
VIC-2DID Yes Yes No Yes Yes
VIC-2CAMA No No No No No
VIC-1J1 No No Yes Yes No
VIC-4FXO-M1 No No No No No
VIC-4FXS/DID Yes3 Yes3 No Yes3 Yes3
VIC2-4FXO (FXO/CAMA) Yes Yes No Yes Yes
VIC2-2FXO (FXO/CAMA) Yes Yes No Yes Yes
VIC2-2FXS Yes Yes No Yes Yes
VIC2-2E/M Yes Yes No Yes Yes
VIC2-2BRI- NT/TE Yes Yes No Yes Yes
VWIC-xMFT-E1 (with or without DI) No Yes Yes Yes Yes
VWIC-1MFT-G703 No No No Yes Yes
VWIC-2MFT-G703 No No Yes Yes Yes
VWIC-xMFT-T1 (with or without DI) No Yes Yes Yes Yes

Note: 

  • 1The NM-HD-1V and NM-HD-2V have feature parity with the NM-1V and NM-2V. However, there is currently no support on NM-1V and NM-2V for:

    • Trunked AAL2 on analog ports

    • Universal FXO (VIC2-xFXO) voice cards with software-selectable CAMA

    • Any VIC2 cards, such as VIC2-2BRI-NT/TE, VIC2-2FXS, VIC2-2E/M, and VIC-4FXS/DID cards

    • The drop of DSPs on a POTS-to-POTS call that stays within the network module

  • 2The NM-HD-2VE interfaces have feature parity with the NM-HDV. However, there is currently no support on the NM-HD-xx for:

    • Modem relay

    There is support for the G.168 ECAN in Cisco IOS Software Release 12.3(4)XD, Cisco IOS Software Release 12.3(7)T, and later. There is support for transcoding and conferencing services in Cisco IOS Software Release 12.3(8)T and later.

  • 3On this platform series and network module type, the VIC-4FXS/DID card currently does not support the DID mode of operation. The voice ports only operate as FXS interfaces. Support for both modes of operation will be available in Cisco IOS Software Release 12.3(14)T. If analog DID is necessary at this time, use the VIC-2DID product instead.

DSP Module Support Matrix

Routers/Gateways
Model (right) 1750 1751/1760 VG200 1
DSP Module (below)
AIM-VOICE-30 No
AIM-ATM-VOICE-30 No
NM-HDV-FARM Yes
PVDM-12 No No Yes
DSP-HDA-16 No No No
PVDM-41 Yes No No
PVDM-81 Yes No No
PVDM-256K-4 No Yes No
PVDM-256K-8 No Yes No
PVDM-256K-16 No Yes No
PVDM-256K-20 No Yes No
PVDM-256K-16HD No Yes No
PVDM-256K-20HD No Yes No
PVDM2-8 No No No
PVDM2-16 No No No
PVDM2-32 No No No
PVDM2-48 No No No
PVDM2-64 No No No

Note: 

Routers/Gateways
Model (right) 261x, 2x, 5x 2600XM, 2691 2801 2811, 2821, 2851 ICS 7750
DSP Module (below)
AIM-VOICE-30 Yes Yes No No
AIM-ATM-VOICE-30 Yes Yes No No
NM-HDV-FARM Yes2 Yes No Yes
PVDM-12 Yes Yes No Yes3 No
DSP-HDA-16 Yes Yes No Yes4 No
PVDM-41 No No No No Yes
PVDM-81 No No No No Yes
PVDM-256K-4 No No No No Yes
PVDM-256K-8 No No No No Yes
PVDM-256K-16 No No No No Yes
PVDM-256K-20 No No No No Yes
PVDM-256K-16HD No No No No No
PVDM-256K-20HD No No No No No
PVDM2-8 No Yes Yes Yes No
PVDM2-16 No Yes Yes Yes No
PVDM2-32 No Yes Yes Yes No
PVDM2-48 No Yes Yes Yes No
PVDM2-64 No Yes Yes Yes No

Note: 

  • 1These products have reached end of sale. Refer to the End-of-Sale Announcement for the Cisco VG200 Access Gateway.

  • 2There is support on the 2650 and 2651, but not on the 261x and 262x.

  • 3The PVDM-12 only has support on the Cisco 2811, 2821, 2851, 3825, and 3845 when the PVDM-12 is installed on a NM-HDV-FARM or NM-HDV network module. The voice router itself only supports the PVDM2 series of DSP cards.

  • 4The DSP-HDA-16 only has support on the Cisco 2811, 2821, 2851, 3825, and 3845 when DSP-HDA-16 is installed on a NM-HDA-4FXS network module. The voice router itself only supports the PVDM2 series of DSP cards.

Routers/Gateways
Model (right) 3620 3640/40A 3660 37xx 3825, 3845
DSP Module (below)
AIM-VOICE-30 No No Yes2 Yes No
AIM-ATM-VOICE-30 No No Yes2 Yes No
NM-HDV-FARM No Yes Yes Yes Yes
PVDM-12 Yes Yes Yes Yes Yes3
DSP-HDA-16 No Yes Yes Yes Yes4
PVDM-41 No No No No No
PVDM-81 No No No No No
PVDM-256K-4 No No No No No
PVDM-256K-8 No No No No No
PVDM-256K-16 No No No No No
PVDM-256K-20 No No No No No
PVDM-256K-16HD No No No No No
PVDM-256K-20HD No No No No No
PVDM2-8 No No No Yes Yes
PVDM2-16 No No No Yes Yes
PVDM2-32 No No No Yes Yes
PVDM2-48 No No No Yes Yes
PVDM2-64 No No No Yes Yes

Note: 

  • 1These products have reached end of sale. Refer to the End-of-Sale Announcement for the Cisco VG200 Access Gateway.

  • 2On the Cisco 3660, the AIM-VOICE-30 and AIM-ATM-VOICE-30 products only have support when there is also a multiservice interchange (MIX) daughter card installed.

  • 3The PVDM-12 only has support on the Cisco 2811, 2821, 2851, 3825, and 3845 when the PVDM-12 is installed on a NM-HDV-FARM or NM-HDV network module. The voice router itself only supports the PVDM2 series of DSP cards.

  • 4The DSP-HDA-16 only has support on the Cisco 2811, 2821, 2851, 3825, and 3845 when DSP-HDA-16 is installed on a NM-HDA-4FXS network module. The voice router itself only supports the PVDM2 series of DSP cards.

Catalyst Support Matrix

This table shows the relationship between Catalyst switches, voice blades, and VICs:

Note: The VICs that are not listed in this matrix do not receive support from the Catalyst switches.

Product Name Catalyst Switches
Catalyst 4500/4000 Access Gateway Module Catalyst 6500/6000 (that runs Catalyst OS [CatOS])
WS-X6608-T1/E1 Provides a high-end T1 gateway to the Public Switched Telephone Network (PSTN) or legacy Private Branch Exchanges (PBXs) and network-based voice services No CatOS 5.5(1)
WS-X6624-FXS Connects legacy analog telephony equipment such as phones, speaker phones, and faxes No CatOS 5.5(3)
WS-X6348-RJ45V Inline power 10/100BASE-T Ethernet switching modules. Equivalent to a WS-X6348-RJ45 10/100BASE-T Ethernet switching module with inline power daughter module WS-F6K-VPWR= No CatOS 5.5(1)
WS-SVC-CMM Provides up to 18 T1/E1 gateways to the PSTN or legacy PBXs and network-based voice services No CatOS 7.3(1)
WS-X4148-RJ45V Inline power 10/100BASE-T Ethernet switching modules CatOS 6.1(1) No
VIC-2FXS Two-port FXS VIC Cisco IOS Software Release 12.1(3a)XI No
VIC-2FXO Two-port FXO VIC Cisco IOS Software Release 12.1(3a)XI No
VIC-2FXO-EU Two-port FXO for Europe Cisco IOS Software Release 12.1(3a)XI No
VIC-2BRI-S/T-TE Two-port ISDN BRI VIC, S/T interface, terminal equipment Yes No
VWIC-1MFT-T1 One-port RJ-48 multiflex trunk T1 Cisco IOS Software Release 12.1(3a)XI No
VWIC-2MFT-T1 Two-port RJ-48 multiflex trunk T1 Cisco IOS Software Release 12.1(3a)XI No
VWIC-2MFT-T1-DI Two-port RJ-48 multiflex trunk E1 with DI Cisco IOS Software Release 12.1(3a)XI No
VWIC-1MFT-E1 One-port RJ-48 multiflex trunk E1 Cisco IOS Software Release 12.1(3a)XI No
VWIC-2MFT-E1 Two-port RJ-48 multiflex trunk E1 Cisco IOS Software Release 12.1(3a)XI No
VWIC-2MFT-E1-DI Two-port RJ-48 multiflex trunk E1 with DI Cisco IOS Software Release 12.1(3a)XI No

Note: The Cisco IOS Software releases provided are typically the minimum version necessary to support the platform, module, or feature in question. For a complete list of Cisco IOS Software releases that support a feature, module, interface card, or chassis, use the Software Advisor (registered customers only) tool.

Related Information

Updated: Jul 31, 2008
Document ID: 5111