Cisco Security Advisory
Click Icon to Copy Verbose Score
CVSS:3.1/AV:N/AC:L/PR:N/UI:N/S:C/C:N/I:N/A:H/E:X/RL:X/RC:X
-
A vulnerability in ICMPv6 processing of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition.
This vulnerability is due to improper processing of ICMPv6 messages. An attacker could exploit this vulnerability by sending crafted ICMPv6 messages to a targeted Cisco ASA or FTD system with IPv6 enabled. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.
Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability.
This advisory is available at the following link:
https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-asa-icmpv6-t5TzqwNdThis advisory is part of the November 2023 release of the Cisco ASA, FTD, and FMC Security Advisory Bundled publication. For a complete list of the advisories and links to them, see Cisco Event Response: November 2023 Semiannual Cisco ASA, FMC, and FTD Software Security Advisory Bundled Publication.
-
Vulnerable Products
This vulnerability affects Cisco ASA Software and FTD Software when it is configured with the IPv6 protocol.
Note: Devices that have only IPv4 interfaces configured are not affected.
Determine the Device Configuration
To determine which interfaces have assigned IPv6 addresses on a device that is running an affected software release and has IPv6 enabled, use the show ipv6 interface brief CLI command, as shown in the following example:
ciscodevice# show ipv6 interface brief
GigabitEthernet0/0 [up/up]
2001:db8:32:16:::1
fdf8:f53b:82e4::53
management [up/up]
unassignedIn addition, if IPv6 is enabled, the ipv6 enable interface configuration command is present in the configuration. The following example shows the output of an affected configuration:
ciscodevice# show running-config interface
interface GigabitEthernet0/0
...
ipv6 enable
...Products Confirmed Not Vulnerable
Only products listed in the Vulnerable Products section of this advisory are known to be affected by this vulnerability.
Cisco has confirmed that this vulnerability does not affect Cisco Firepower Management Center (FMC) Software.
-
There are no workarounds that address this vulnerability.
-
Cisco has released free software updates that address the vulnerability described in this advisory. Customers with service contracts that entitle them to regular software updates should obtain security fixes through their usual update channels.
Customers may only install and expect support for software versions and feature sets for which they have purchased a license. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to follow the terms of the Cisco software license:
https://www.cisco.com/c/en/us/products/end-user-license-agreement.htmlAdditionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades.
The Cisco Support and Downloads page on Cisco.com provides information about licensing and downloads. This page can also display customer device support coverage for customers who use the My Devices tool.
When considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories page, to determine exposure and a complete upgrade solution.
In all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.
Customers Without Service Contracts
Customers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco TAC: https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html
Customers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade.
Cisco ASA, FMC, and FTD Software
To help customers determine their exposure to vulnerabilities in Cisco ASA, FMC, and FTD Software, Cisco provides the Cisco Software Checker. This tool identifies any Cisco security advisories that impact a specific software release and the earliest release that fixes the vulnerabilities that are described in each advisory (“First Fixed”). If applicable, the tool also returns the earliest release that fixes all the vulnerabilities that are described in all the advisories that the Software Checker identifies (“Combined First Fixed”).
To use the tool, go to the Cisco Software Checker page and follow the instructions. Alternatively, use the following form to search for vulnerabilities that affect a specific software release. To use the form, follow these steps:
- Choose which advisories the tool will search—all advisories, only advisories with a Critical or High Security Impact Rating (SIR), or only this advisory.
- Choose the appropriate software.
- Choose the appropriate platform.
- Enter a release number—for example, 9.16.2.11 for Cisco ASA Software or 6.6.7 for Cisco FTD Software.
- Click Check.
For instructions on upgrading your FTD device, see Cisco Firepower Management Center Upgrade Guide.
-
The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.
-
This vulnerability was found during internal security testing.
-
To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.
-
Show LessVersion Description Section Status Date 1.1 Updated the Cisco Software Checker form. Fixed Software Final 2023-NOV-02 1.0 Initial public release. — Final 2023-NOV-01
-
THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.
A standalone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy and may lack important information or contain factual errors. The information in this document is intended for end users of Cisco products.