Summary

• A vulnerability in the implementation of the Short Message Service (SMS) handling functionality of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to trigger a denial of service (DoS) condition on an affected device.

  The vulnerability is due to improper processing of SMS protocol data units (PDUs) that are encoded with a special character set. An attacker could exploit this vulnerability by sending a malicious SMS message to an affected device. A successful exploit could allow the attacker to cause the wireless WAN (WWAN) cellular interface module on an affected device to crash, resulting in a DoS condition that would require manual intervention to restore normal operating conditions.

  Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability.
  
  This advisory is available at the following link:
  https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190327-sms-dos

  This advisory is part of the March 27, 2019, release of the Cisco IOS and IOS XE Software Security Advisory Bundled Publication, which includes 17 Cisco Security Advisories that describe 19 vulnerabilities. For a complete list of the advisories and links to them, see Cisco Event Response: March 2019 Semiannual Cisco IOS and IOS XE Software Security Advisory Bundled Publication.

Affected Products

• Vulnerable Products

  This vulnerability affects Cisco routers that have a Sierra Wireless WWAN cellular interface module installed and that are running either Cisco IOS Software Release 15.8(3)M or Cisco IOS XE Software Release 16.10.1. The SMS handling functionality is enabled by default only when an active subscriber identity module (SIM) card is installed on a Sierra Wireless WWAN cellular interface module.

  For information about which Cisco IOS and IOS XE Software releases are vulnerable, see the Fixed Software section of this advisory.

  Determining Whether a Device Is Using an Embedded Sierra Wireless WWAN Cellular Interface Module

  To determine whether a Cisco router is using a Sierra Wireless WWAN cellular interface module, use the show inventory | include Sierra Wireless privileged EXEC command on the device. The following example shows the output of the show inventory | include Sierra Wireless command on a router with a Sierra Wireless MC7750 WWAN cellular interface module.

  Router#show inventory | include Sierra Wireless
  NAME: "Modem 0 on Cellular0", DESCR: "Sierra Wireless MC7750 4G-V"

  The modem slot number, the cellular interface number, and the description differ depending on the platform and the model of the WWAN cellular interface module installed. However, if this command does not exist, or it does not produce any output, the device is not affected by the vulnerability described in this advisory.

  Determining the Cisco IOS Software Release

  To determine which Cisco IOS Software release is running on a device, administrators can log in to the device, use the show version command in the CLI, and then refer to the system banner that appears. If the device is running Cisco IOS Software, the system banner displays text similar to Cisco Internetwork Operating System Software or Cisco IOS Software. The banner also displays the installed image name in parentheses, followed by the Cisco IOS Software release number and release name. Some Cisco devices do not support the show version command or may provide different output.

  The following example shows the output of the command for a device that is running Cisco IOS Software Release 15.5(2)T1 and has an installed image name of C2951-UNIVERSALK9-M:

  Router> show version
  
  Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.5(2)T1, RELEASE SOFTWARE (fc1)
  Technical Support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2015 by Cisco Systems, Inc.
  Compiled Mon 22-Jun-15 09:32 by prod_rel_team
  .
  .
  .

  For information about the naming and numbering conventions for Cisco IOS Software releases, see the Cisco IOS and NX-OS Software Reference Guide.

  Determining the Cisco IOS XE Software Release

  To determine which Cisco IOS XE Software release is running on a device, administrators can log in to the device, use the show version command in the CLI, and then refer to the system banner that appears. If the device is running Cisco IOS XE Software, the system banner displays Cisco IOS Software, Cisco IOS XE Software, or similar text.

  The following example shows the output of the command for a device that is running Cisco IOS XE Software Release 16.2.1 and has an installed image name of CAT3K_CAA-UNIVERSALK9-M:

  ios-xe-device# show version
  
  Cisco IOS Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version Denali 16.2.1, RELEASE SOFTWARE (fc1)
  Technical Support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2016 by Cisco Systems, Inc.
  Compiled Sun 27-Mar-16 21:47 by mcpre
  .
  .
  .

  For information about the naming and numbering conventions for Cisco IOS XE Software releases, see the Cisco IOS and NX-OS Software Reference Guide.

  Products Confirmed Not Vulnerable

  Only products listed in the Vulnerable Products section of this advisory are known to be affected by this vulnerability.

  Cisco has confirmed that this vulnerability does not affect Cisco IOS XR Software or Cisco NX-OS Software.

Details

• Successful exploitation of this vulnerability will cause the WWAN cellular interface module on an affected device to crash. The crashed state is localized within the WWAN cellular interface module and does not extend to other modules or processes that are running on the device.

  Customers whose devices have been affected by successful exploitation of this vulnerability are advised to contact the Cisco Technical Assistance Center (TAC) or their Customer Experience (CX) representative for assistance in recovering the WWAN functionality.

Indicators of Compromise

• Exploitation of this vulnerability could cause the affected device to repeatedly generate an error message similar to the following:

  %Router-2-MODEM_DOWN: Cellular0 modem is now DOWN

  Customers are advised to contact their support organization to review the error message and determine whether the device has been affected by exploitation of this vulnerability.

Workarounds

• There are no workarounds that address this vulnerability.

Fixed Software

• Cisco has released free software updates that address the vulnerability described in this advisory. Customers may only install and expect support for software versions and feature sets for which they have purchased a license. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to follow the terms of the Cisco software license:
  https://www.cisco.com/c/en/us/products/end-user-license-agreement.html

  Additionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades.

  When considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories and Alerts page, to determine exposure and a complete upgrade solution.

  In all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.

  Customers Without Service Contracts

  Customers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco TAC:
  https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html

  Customers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade.

  Cisco IOS and IOS XE Software

  To help customers determine their exposure to vulnerabilities in Cisco IOS and IOS XE Software, Cisco provides a tool, the Cisco IOS Software Checker, that identifies any Cisco Security Advisories that impact a specific software release and the earliest release that fixes the vulnerabilities described in each advisory (“First Fixed”). If applicable, the tool also returns the earliest release that fixes all the vulnerabilities described in all the advisories identified (“Combined First Fixed”).

  Customers can use this tool to perform the following tasks:

  • Initiate a search by choosing one or more releases from a drop-down list or uploading a file from a local system for the tool to parse
  • Enter the output of the show version command for the tool to parse
  • Create a custom search by including all previously published Cisco Security Advisories, a specific advisory, or all advisories in the most recent bundled publication

  To determine whether a release is affected by any published Cisco Security Advisory, use the Cisco IOS Software Checker on Cisco.com or enter a Cisco IOS or IOS XE Software release—for example, 15.1(4)M2 or 3.13.8S—in the following field:

  By default, the Cisco IOS Software Checker includes results only for vulnerabilities that have a Critical or High Security Impact Rating (SIR). To include results for Medium SIR vulnerabilities, use the Cisco IOS Software Checker on Cisco.com and check the Medium check box in the Impact Rating drop-down list.

  For a mapping of Cisco IOS XE Software releases to Cisco IOS Software releases, refer to the Cisco IOS XE 2 Release Notes, Cisco IOS XE 3S Release Notes, or Cisco IOS XE 3SG Release Notes, depending on the Cisco IOS XE Software release.

  Note: Starting with Cisco IOS XE Software Release 16.9.1, any upgrade will require Smart Licensing. Customers who plan to upgrade Cisco IOS XE to Release 16.9.1 or later are advised to consider the Smart Licensing requirement. The following documentation provides additional information: Smart Licensing.

Exploitation and Public Announcements

• The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.

Source

• This vulnerability was found during the resolution of a Cisco TAC support case.

URL

• https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190327-sms-dos

Revision History

• Version	Description	Section	Status	Date
  1.0	Initial public release.	—	Final	2019-March-27

  Show Less

---