Supported MIBs
This appendix lists the supported management information base (MIBs) for this release on the Catalyst 2960 switch. It contains these sections:
•
MIB List
•
Using FTP to Access the MIB Files
MIB List
•
BRIDGE-MIB
Note
The BRIDGE-MIB supports the context of a single VLAN. By default, SNMP messages using the configured community string always provide information for VLAN 1. To obtain the BRIDGE-MIB information for other VLANs, for example VLAN x, use this community string in the SNMP message: configured community string @x.
•
CISCO-CABLE-DIAG-MIB
•
CISCO-CDP-MIB
•
CISCO-CLUSTER-MIB
•
CISCO-CONFIG-COPY-MIB
•
CISCO-CONFIG-MAN-MIB
•
CISCO-ENTITY-VENDORTYPE-OID-MIB
•
CISCO-ENVMON-MIB
•
CISCO-ERR-DISABLE-MIB
•
CISCO-FLASH-MIB (Flash memory on all switches is modeled as removable flash memory.)
•
CISCO-FTP-CLIENT-MIB
•
CISCO-IGMP-FILTER-MIB
•
CISCO-IMAGE-MIB
•
CISCO IP-STAT-MIB
•
CISCO-LAG-MIB
•
CISCO-MAC-NOTIFICATION-MIB
•
CISCO-MEMORY-POOL-MIB
•
CISCO-NAC-NAD-MIB
•
CISCO-PAE-MIB
•
CISCO-PAGP-MIB
•
CISCO-PING-MIB
•
CISCO-PORT-QOS-MIB (only the packet counters are supported; the octet counters are not supported)
•
CISCO-POWER-ETHERNET-EXT-MIB
•
CISCO-PRODUCTS-MIB
•
CISCO-PROCESS-MIB
•
CISCO-RTTMON-MIB
•
CISCO-SMI-MIB
•
CISCO-STP-EXTENSIONS-MIB
•
CISCO-SYSLOG-MIB
•
CISCO-TC-MIB
•
CISCO-TCP-MIB
•
CISCO-UDLDP-MIB
•
CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB
•
CISCO-VLAN-MEMBERSHIP-MIB
•
CISCO-VTP-MIB
•
ENTITY-MIB
•
ETHERLIKE-MIB
•
IEEE8021-PAE-MIB
•
IEEE8023-LAG-MIB
•
IF-MIB (In and out counters for VLANs are not supported.)
•
IGMP-MIB
•
INET-ADDRESS-MIB
•
•
OLD-CISCO-CHASSIS-MIB
•
OLD-CISCO-FLASH-MIB
•
OLD-CISCO-INTERFACES-MIB
•
OLD-CISCO-IP-MIB
•
OLD-CISCO-SYS-MIB
•
OLD-CISCO-TCP-MIB
•
OLD-CISCO-TS-MIB
•
RFC1213-MIB (Functionality is as per the agent capabilities specified in the CISCO-RFC1213-CAPABILITY.my.)
•
RMON-MIB
•
RMON2-MIB
•
SNMP-FRAMEWORK-MIB
•
SNMP-MPD-MIB
•
SNMP-NOTIFICATION-MIB
•
SNMP-TARGET-MIB
•
SNMPv2-MIB
•
TCP-MIB
•
UDP-MIB
Note
You can also use this URL for a list of supported MIBs for the Catalyst 2960 switch:
ftp://ftp.cisco.com/pub/mibs/supportlists/cat2960/cat2960-supportlist.html
You can access other information about MIBs and Cisco products on the Cisco web site:
http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml
Using FTP to Access the MIB Files
You can get each MIB file by using this procedure:
Step 1
Make sure that your FTP client is in passive mode.
Note
Some FTP clients do not support passive mode.
Step 2
Use FTP to access the server ftp.cisco.com.
Step 3
Log in with the username anonymous.
Step 4
Enter your e-mail username when prompted for the password.
Step 5
At the ftp>
prompt, change directories to /pub/mibs/v1 and /pub/mibs/v2.
Step 6
Use the get MIB_filename command to obtain a copy of the MIB file.