 Feedback
|
Table Of Contents
Assigning the Switch IP Address and Default Gateway
Understanding the Boot Process
Understanding DHCP-Based Autoconfiguration
Understanding DHCP-based Autoconfiguration and Image Update
Configuring DHCP-Based Autoconfiguration
DHCP Server Configuration Guidelines
Configuring the DHCP Auto Configuration and Image Update Features
Configuring DHCP Autoconfiguration (Only Configuration File)
Configuring DHCP Auto-Image Update (Configuration File and Image)
Manually Assigning IP Information
Checking and Saving the Running Configuration
Modifying the Startup Configuration
Automatically Downloading a Configuration File
Specifying the Filename to Read and Write the System Configuration
Booting a Specific Software Image
Controlling Environment Variables
Scheduling a Reload of the Software Image
Configuring a Scheduled Reload
Displaying Scheduled Reload Information
Assigning the Switch IP Address and Default Gateway
This chapter describes how to create the initial switch configuration (for example, assigning the switch IP address and default gateway information) for the Cisco Metro Ethernet (ME) 3800X and 3600X switch by using a variety of automatic and manual methods. It also describes how to modify the switch startup configuration.
Note
For complete syntax and usage information for the commands used in this chapter, refer to the command reference for this release and to the Cisco IOS Software Documentation Command References, IP Addressing Services.
This chapter consists of these sections:
•
•
•
•
Note
Understanding the Boot Process
To start your switch, you need to follow the procedures in the hardware installation guide about installing and powering on the switch and setting up the initial configuration (IP address, subnet mask, default gateway, secret and Telnet passwords, and so forth) of the switch.
The normal boot process involves the operation of the boot loader software, which performs these functions:
•
•
•
•
The boot loader provides access to the flash file system before the operating system is loaded. Normally, the boot loader is used only to load, uncompress, and launch the operating system. After the boot loader gives the operating system control of the CPU, the boot loader is not active until the next system reset or power-on.
The boot loader also provides trap-door access into the system if the operating system has problems serious enough that it cannot be used. The trap-door mechanism provides enough access to the system so that if it is necessary, you can format the flash file system, reinstall the operating system software image by using the XMODEM Protocol, recover from a lost or forgotten password, and finally restart the operating system. For more information, see the "Recovering from a Lost or Forgotten Password" section.
Note
Before you can assign switch information, make sure you have connected a PC or terminal to the console port, and configured the PC or terminal-emulation software baud rate and character format to match these of the switch console port:
•
•
Note
•
•
Initial Configuration
The switch is set to automatically boot to the bootloader. When the bootloader is fully operational, the prompt appears:
switch:See the "Boot Loader Commands" appendix in the command reference for this release for descriptions of the available commands. To manually boot an image from flash memory, enter:
switch: boot flash: image nameIf you do not know the image name on the flash memory, you can retrieve the name with this command:
switch:dir flash:Directory of flash:/2 -rwx 2072 <date> multiple-fs3 -rwx 5 <date> private-config.text4 -rwx 3045 <date> config.text5 drwx 512 <date> me380x-universal-mz.122-52.1.127.EY16920593 bytes available (41011183 bytes used)If the dir flash command does not work, enter:
switch: flash_init:This command initialize the flash so the contents can be read, without erasing any of the flash memory contents.
After the switch becomes operational on an image, you can specify the image to boot from by using the boot global configuration command. See the "Modifying the Startup Configuration" section.
Assigning Switch Information
You can assign IP information through the switch setup program, through a DHCP server, or manually.
Use the switch setup program if you want to be prompted for specific IP information. With this program, you can also configure a hostname and an enable secret password. It gives you the option of assigning a Telnet password (to provide security during remote management). For more information about the setup program, see the "Configuring the Switch with the CLI-Based Setup Program" appendix in the hardware installation guide.
Use a DHCP server for centralized control and automatic assignment of IP information after the server is configured.
Note
If you are an experienced user familiar with the switch configuration steps, manually configure the switch. Otherwise, use the setup program described previously.
These sections contain this configuration information:
•
•
Default Switch Information
Table 3-1 shows the default switch information.
Understanding DHCP-Based Autoconfiguration
DHCP provides configuration information to Internet hosts and internetworking devices. This protocol consists of two components: one for delivering configuration parameters from a DHCP server to a device and a mechanism for allocating network addresses to devices. DHCP is built on a client-server model, in which designated DHCP servers allocate network addresses and deliver configuration parameters to dynamically configured devices. The switch can act as both a DHCP client and a DHCP server.
During DHCP-based autoconfiguration, your switch (DHCP client) is automatically configured at startup with IP address information and a configuration file.
With DHCP-based autoconfiguration, no DHCP client-side configuration is needed on your switch. However, you need to configure the DHCP server for various lease options associated with IP addresses. If you are using DHCP to relay the configuration file location on the network, you might also need to configure a Trivial File Transfer Protocol (TFTP) server and a Domain Name System (DNS) server.
The DHCP server for your switch can be on the same LAN or on a different LAN than the switch. If the DHCP server is running on a different LAN, you should configure a DHCP relay device between your switch and the DHCP server. A relay device forwards broadcast traffic between two directly connected LANs. A router does not forward broadcast packets, but it forwards packets based on the destination IP address in the received packet.
DHCP-based autoconfiguration replaces the BOOTP client functionality on your switch.
DHCP Client Request Process
When you boot your switch, the DHCP client is invoked and requests configuration information from a DHCP server when the configuration file is not present on the switch. If the configuration file is present and the configuration includes the ip address dhcp interface configuration command on specific routed interfaces, the DHCP client is invoked and requests the IP address information for those interfaces.
Figure 3-1 shows the sequence of messages that are exchanged between the DHCP client and the DHCP server.
Figure 3-1 DHCP Client and Server Message Exchange
The client, Switch A, broadcasts a DHCPDISCOVER message to locate a DHCP server. The DHCP server offers configuration parameters (such as an IP address, subnet mask, gateway IP address, DNS IP address, a lease for the IP address, and so forth) to the client in a DHCPOFFER unicast message.
In a DHCPREQUEST broadcast message, the client returns a formal request for the offered configuration information to the DHCP server. The formal request is broadcast so that all other DHCP servers that received the DHCPDISCOVER broadcast message from the client can reclaim the IP addresses that they offered to the client.
The DHCP server confirms that the IP address has been allocated to the client by returning a DHCPACK unicast message to the client. With this message, the client and server are bound, and the client uses configuration information received from the server. The amount of information the switch receives depends on how you configure the DHCP server. For more information, see the "Configuring the TFTP Server" section.
If the configuration parameters sent to the client in the DHCPOFFER unicast message are invalid (a configuration error exists), the client returns a DHCPDECLINE broadcast message to the DHCP server.
The DHCP server sends the client a DHCPNAK denial broadcast message, which means that the offered configuration parameters have not been assigned, that an error has occurred during the negotiation of the parameters, or that the client has been slow in responding to the DHCPOFFER message (the DHCP server assigned the parameters to another client).
A DHCP client might receive offers from multiple DHCP or BOOTP servers and can accept any of the offers; however, the client usually accepts the first offer it receives. The offer from the DHCP server is not a guarantee that the IP address is allocated to the client; however, the server usually reserves the address until the client has had a chance to formally request the address. If the switch accepts replies from a BOOTP server and configures itself, the switch broadcasts, instead of unicasts, TFTP requests to obtain the switch configuration file.
The DHCP hostname option allows a group of switches to obtain hostnames and a standard configuration from the central management DHCP server. A client (switch) includes in its DCHPDISCOVER message an option 12 field used to request a hostname and other configuration parameters from the DHCP server. The configuration files on all clients are identical except for their DHCP-obtained hostnames.
If a client has a default hostname (the hostname name global configuration command is not configured or the no hostname global configuration command is entered to remove the hostname), the DHCP hostname option is not included in the packet when you enter the ip address dhcp interface configuration command. In this case, if the client receives the DCHP hostname option from the DHCP interaction while acquiring an IP address for an interface, the client accepts the DHCP hostname option and sets the flag to show that the system now has a hostname configured.
Understanding DHCP-based Autoconfiguration and Image Update
You can use the DHCP image upgrade features to configure a DHCP server to download both a new image and a new configuration file to one or more switches in a network. This helps ensure that each new switch added to a network receives the same image and configuration.
There are two types of DHCP image upgrades: DHCP autoconfiguration and DHCP auto-image update.
DHCP Autoconfiguration
DHCP autoconfiguration downloads a configuration file to one or more switches in your network from a DHCP server. The downloaded configuration file becomes the running configuration of the switch. It does not over write the bootup configuration saved in the flash, until you reload the switch.
DHCP Auto-Image Update
You can use DHCP auto-image upgrade with DHCP autoconfiguration to download both a configuration and a new image to one or more switches in your network. The switch (or switches) downloading the new configuration and the new image can be blank (or only have a default factory configuration loaded).
If the new configuration is downloaded to a switch that already has a configuration, the downloaded configuration is appended to the configuration file stored on the switch. (Any existing configuration is not overwritten by the downloaded one.)
Note
For procedures to configure the switch as a DHCP server, see the "Configuring DHCP-Based Autoconfiguration" section and the IP Addressing: DHCP Configuration Guide, Cisco IOS Release 15.x.
After you install the switch in your network, the auto-image update feature starts. The downloaded configuration file is saved in the running configuration of the switch, and the new image is downloaded and installed on the switch. When you reboot the switch, the configuration is stored in the saved configuration on the switch.
Limitations and Restrictions
These are the limitations:
•
•
•
Note
Configuring DHCP-Based Autoconfiguration
These sections contain this configuration information:
•
•
If your DHCP server is a Cisco device, see the IP Addressing: DHCP Configuration Guide, Cisco IOS Release 15.x. for additional information about configuring DHCP.
DHCP Server Configuration Guidelines
Follow these guidelines if you are configuring a device as a DHCP server:
You should configure the DHCP server with reserved leases that are bound to each switch by the switch hardware address.
If you want the switch to receive IP address information, you must configure the DHCP server with these lease options:
•
•
•
•
If you want the switch to receive the configuration file from a TFTP server, you must configure the DHCP server with these lease options:
•
•
•
Depending on the settings of the DHCP server, the switch can receive IP address information, the configuration file, or both.
If you do not configure the DHCP server with the lease options described previously, it replies to client requests with only those parameters that are configured. If the IP address and the subnet mask are not in the reply, the switch is not configured. If the router IP address or the TFTP server name are not found, the switch might send broadcast, instead of unicast, TFTP requests. Unavailability of other lease options does not affect autoconfiguration.
The switch can act as a DHCP server. By default, the Cisco IOS DHCP server and relay agent features are enabled on your switch but are not configured. These features are not operational. If your DHCP server is a Cisco device, for additional information about configuring DHCP, refer to the IP Addressing: DHCP Configuration Guide, Cisco IOS Release 15.x.
Configuring the TFTP Server
Based on the DHCP server configuration, the switch attempts to download one or more configuration files from the TFTP server. If you configured the DHCP server to respond to the switch with all the options required for IP connectivity to the TFTP server, and if you configured the DHCP server with a TFTP server name, address, and configuration filename, the switch attempts to download the specified configuration file from the specified TFTP server.
If you did not specify the configuration filename, the TFTP server, or if the configuration file could not be downloaded, the switch attempts to download a configuration file by using various combinations of filenames and TFTP server addresses. The files include the specified configuration filename (if any) and these files: network-config, cisconet.cfg, hostname.config, or hostname.cfg, where hostname is the switch's current hostname. The TFTP server addresses used include the specified TFTP server address (if any) and the broadcast address (255.255.255.255).
For the switch to successfully download a configuration file, the TFTP server must contain one or more configuration files in its base directory. The files can include these files:
•
•
•
If you specify the TFTP server name in the DHCP server-lease database, you must also configure the TFTP server name-to-IP-address mapping in the DNS-server database.
If the TFTP server to be used is on a different LAN from the switch, or if it is to be accessed by the switch through the broadcast address (which occurs if the DHCP server response does not contain all the required information described previously), a relay must be configured to forward the TFTP packets to the TFTP server. For more information, see the "Configuring the Relay Device" section. The preferred solution is to configure the DHCP server with all the required information.
Configuring the DNS
The DHCP server uses the DNS server to resolve the TFTP server name to an IP address. You must configure the TFTP server name-to-IP address map on the DNS server. The TFTP server contains the configuration files for the switch.
You can configure the IP addresses of the DNS servers in the lease database of the DHCP server from where the DHCP replies will retrieve them. You can enter up to two DNS server IP addresses in the lease database.
The DNS server can be on the same or on a different LAN as the switch. If it is on a different LAN, the switch must be able to access it through a router.
Configuring the Relay Device
You must configure a relay device, also referred to as a relay agent, when a switch sends broadcast packets that require a response from a host on a different LAN. Examples of broadcast packets that the switch might send are DHCP, DNS, and in some cases, TFTP packets. You must configure this relay device to forward received broadcast packets on an interface to the destination host.
If the relay device is a Cisco router, enable IP routing (ip routing global configuration command), and configure helper addresses by using the ip helper-address interface configuration command.
For example, in Figure 3-2, configure the router interfaces as follows:
On interface 10.0.0.2:
router(config-if)#ip helper-address 20.0.0.2router(config-if)#ip helper-address 20.0.0.3router(config-if)#ip helper-address 20.0.0.4On interface 20.0.0.1
router(config-if)#ip helper-address 10.0.0.1
Note
Figure 3-2 Relay Device Used in Autoconfiguration
Obtaining Configuration Files
Depending on the availability of the IP address and the configuration filename in the DHCP reserved lease, the switch obtains its configuration information in these ways:
•
The switch receives its IP address, subnet mask, TFTP server address, and the configuration filename from the DHCP server. The switch sends a unicast message to the TFTP server to retrieve the named configuration file from the base directory of the server and upon receipt, it completes its boot-up process.
•
The switch receives its IP address, subnet mask, and the configuration filename from the DHCP server. The switch sends a broadcast message to a TFTP server to retrieve the named configuration file from the base directory of the server, and upon receipt, it completes its boot-up process.
•
The switch receives its IP address, subnet mask, and the TFTP server address from the DHCP server. The switch sends a unicast message to the TFTP server to retrieve the network-confg or cisconet.cfg default configuration file. (If the network-confg file cannot be read, the switch reads the cisconet.cfg file.)
The default configuration file contains the hostnames-to-IP-address mapping for the switch. The switch fills its host table with the information in the file and obtains its hostname. If the hostname is not found in the file, the switch uses the hostname in the DHCP reply. If the hostname is not specified in the DHCP reply, the switch uses the default Switch as its hostname.
After obtaining its hostname from the default configuration file or the DHCP reply, the switch reads the configuration file that has the same name as its hostname (hostname-confg or hostname.cfg, depending on whether network-confg or cisconet.cfg was read earlier) from the TFTP server. If the cisconet.cfg file is read, the filename of the host is truncated to eight characters.
If the switch cannot read the network-confg, cisconet.cfg, or the hostname file, it reads the router-confg file. If the switch cannot read the router-confg file, it reads the ciscortr.cfg file.
Note
Example Configuration
Figure 3-3 shows a sample network for retrieving IP information by using DHCP-based autoconfiguration.
Figure 3-3 DHCP-Based Autoconfiguration Network Example
Table 3-2 shows the configuration of the reserved leases on the DHCP server.
DNS Server Configuration
The DNS server maps the TFTP server name tftpserver to IP address 10.0.0.3.
TFTP Server Configuration (on UNIX)
The TFTP server base directory is set to /tftpserver/work/. This directory contains the network-confg file used in the two-file read method. This file contains the hostname to be assigned to the switch based on its IP address. The base directory also contains a configuration file for each switch (switcha-confg, switchb-confg, and so forth) as shown in this display:
prompt> cd /tftpserver/work/prompt> lsnetwork-confgswitcha-confgswitchb-confgswitchc-confgswitchd-confgprompt> cat network-confgip host switcha 10.0.0.21ip host switchb 10.0.0.22ip host switchc 10.0.0.23ip host switchd 10.0.0.24DHCP Client Configuration
No configuration file is present on Switch A through Switch D.
Configuration Explanation
In Figure 3-3, Switch A reads its configuration file as follows:
•
•
•
•
•
Switches B through D retrieve their configuration files and IP addresses in the same way.
Configuring the DHCP Auto Configuration and Image Update Features
Using DHCP to download a new image and a new configuration to a switch requires that you configure at least two switches: One switch acts as a DHCP and TFTP server. The client switch is configured to download either a new configuration file or a new configuration file and a new image file.
Configuring DHCP Autoconfiguration (Only Configuration File)
Beginning in privileged EXEC mode, follow these steps to configure DHCP autoconfiguration of the TFTP and DHCP settings on a new switch to download a new configuration file.
This example shows how to configure a switch as a DHCP server so that it will download a configuration file:Switch# configure terminalSwitch(config)# ip dhcp pool pool1Switch(dhcp-config)# network 10.10.10.0 255.255.255.0Switch(dhcp-config)# bootfile config-boot.textSwitch(dhcp-config)# default-router 10.10.10.1Switch(dhcp-config)# option 150 10.10.10.1Switch(dhcp-config)# exitSwitch(config)# tftp-server flash:config-boot.textSwitch(config)# interface gigabitethernet0/4Switch(config-if)# no switchportSwitch(config-if)# ip address 10.10.10.1 255.255.255.0Switch(config-if)# endConfiguring DHCP Auto-Image Update (Configuration File and Image)
Beginning in privileged EXEC mode, follow these steps to configure DHCP autoconfiguration to configure TFTP and DHCP settings on a new switch to download a new image and a new configuration file.
Note
This example shows how to configure a switch as a DHCP server so it downloads a configuration file:Switch# config terminalSwitch(config)# ip dhcp pool pool1Switch(dhcp-config)# network 10.10.10.0 255.255.255.0Switch(dhcp-config)# bootfile config-boot.textSwitch(dhcp-config)# default-router 10.10.10.1Switch(dhcp-config)# option 150 10.10.10.1Switch(dhcp-config)# option 125 hex 0000.0009.0a05.08661.7574.6f69.6e73.7461.6c6c.5f64.686370Switch(dhcp-config)# exitSwitch(config)# tftp-server flash:config-boot.textSwitch(config)# tftp-server flash:-image-name-mz.122-44.3.SE.tarSwitch(config)# tftp-server flash:boot-config.textSwitch(config)# tftp-server flash: autoinstall_dhcpSwitch(config)# interface gigabitEthernet0/4Switch(config-if)# no switchportSwitch(config-if)# ip address 10.10.10.1 255.255.255.0Switch(config-if)# endConfiguring the Client
Beginning in privileged EXEC mode, follow these steps to configure a switch to download a configuration file and new image from a DHCP server:
This example uses a Layer 3 SVI interface on VLAN 99 to enable DHCP-based autoconfiguration with a saved configuration:
Switch# configure terminalSwitch(conf)# boot host dhcpSwitch(conf)# boot host retry timeout 300Switch(conf)# banner config-save ^C Caution - Saving Configuration File to NVRAM May Cause You to Nolonger Automatically Download Configuration Files at Reboot^CSwitch(config)# vlan 99Switch(config-vlan)# interface vlan 99Switch(config-if)# no shutdownSwitch(config-if)# endSwitch# show bootBOOT path-list:Config file: flash:/config.textPrivate Config file: flash:/private-config.textEnable Break: noManual Boot: noHELPER path-list:NVRAM/Config filebuffer size: 32768Timeout for ConfigDownload: 300 secondsConfig Downloadvia DHCP: enabled (next boot: enabled)
Note
Manually Assigning IP Information
Beginning in privileged EXEC mode, follow these steps to manually assign IP information to a switch virtual interface (SVI).You can also manually assign IP information to a port if you first put the port into Layer 3 mode by using the no switchport command.
To remove the switch IP address, use the no ip address interface configuration command. If you are removing the address through a Telnet session, your connection to the switch will be lost. To remove the default gateway address, use the no ip default-gateway global configuration command.
For information on setting the switch system name, protecting access to privileged EXEC commands, and setting time and calendar services, see Chapter 5 "Administering the Switch."
Checking and Saving the Running Configuration
You can check the configuration settings you entered or changes you made by entering this privileged EXEC command:
Switch# show running-configBuilding configuration...Current configuration : 1817 bytes!version 15.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Switch!!no aaa new-modelauthentication mac-move permitip subnet-zero!!license boot level AdvancedMetroIPAccess!!spanning-tree mode rapid-pvstspanning-tree extend system-id!vlan internal allocation policy ascending!vlan 2,10!!interface GigabitEthernet0no ip addressshutdownnegotiation auto!interface GigabitEthernet0/1port-type nni!interface GigabitEthernet0/2port-type nni!interface GigabitEthernet0/3port-type nni!<output truncated>port-type nni!interface TenGigabitEthernet0/1port-type nni!interface TenGigabitEthernet0/2port-type nni!interface Vlan1no ip addressshutdown!ip classlessip http server!!line con 0speed 115200line vty 5 15!EndTo store the configuration or changes you have made to your startup configuration in flash memory, enter this privileged EXEC command:
Switch# copy running-config startup-configDestination filename [startup-config]?Building configuration...This command saves the configuration settings that you made. If you fail to do this, your configuration will be lost the next time you reload the system. To display information stored in the NVRAM section of flash memory, use the show startup-config or more startup-config privileged EXEC command.
For more information about alternative locations from which to copy the configuration file, see "Working with the Cisco IOS File System, Configuration Files, and Software Images."
Modifying the Startup Configuration
•
•
•
See also "Working with the Cisco IOS File System, Configuration Files, and Software Images," for information about switch configuration files.
Default Boot Configuration
Automatically Downloading a Configuration File
You can automatically download a configuration file to your switch by using the DHCP-based autoconfiguration feature. For more information, see the "Understanding DHCP-Based Autoconfiguration" section.
Specifying the Filename to Read and Write the System Configuration
By default, the Cisco IOS software uses the file config.text to read and write a nonvolatile copy of the system configuration. However, you can specify a different filename, which will be loaded during the next boot cycle.
Beginning in privileged EXEC mode, follow these steps to specify a different configuration filename:
To return to the default setting, use the no boot config-file global configuration command.
Booting Manually
By default, the switch automatically boots; however, you can configure it to manually boot.
Beginning in privileged EXEC mode, follow these steps to configure the switch to manually boot during the next boot cycle:
To disable manual booting, use the no boot manual global configuration command.
Booting a Specific Software Image
By default, the switch attempts to automatically boot the system using information in the BOOT environment variable. If this variable is not set, the switch attempts to load and execute the first executable image it can by performing a recursive, depth-first search throughout the flash file system. In a depth-first search of a directory, each encountered subdirectory is completely searched before continuing the search in the original directory. However, you can specify a specific image to boot.
Beginning in privileged EXEC mode, follow these steps to configure the switch to boot a specific image during the next boot cycle:
To return to the default setting, use the no boot system global configuration command.
Controlling Environment Variables
With a normally operating switch, you enter the boot loader mode only through a switch console connection configured for 9600 bps. Unplug and then reconnect the switch power cord. After the switch performs POST, the switch begins the autoboot process. The boot loader prompts the user for a break key character during the boot-up sequence, as shown in this example:
***** The system will autoboot in 5 seconds *****Send a break key to prevent autobooting.The break key character is different for each operating system.
•
•
Note
http://www.cisco.com/en/US/products/hw/routers/ps133/products_tech_note09186a0080174a34.shtml
When you enter the break key, the boot loader switch: prompt appears.
The switch boot loader software provides support for nonvolatile environment variables, which can be used to control how the boot loader, or any other software running on the system, behaves. Boot loader environment variables are similar to environment variables that can be set on UNIX or DOS systems.
Environment variables that have values are stored in flash memory outside of the flash file system.
Each line in these files contains an environment variable name and an equal sign followed by the value of the variable. A variable has no value if it is not listed in this file; it has a value if it is listed in the file even if the value is a null string. A variable that is set to a null string (for example, " ") is a variable with a value. Many environment variables are predefined and have default values.
Environment variables store two kinds of data:
•
•
You can change the settings of the environment variables by accessing the boot loader or by using Cisco IOS commands. Under normal circumstances, it is not necessary to alter the setting of the environment variables.
Note
Table 3-4 describes the function of the most common environment variables.
Scheduling a Reload of the Software Image
You can schedule a reload of the software image to occur on the switch at a later time (for example, late at night or during the weekend when the switch is used less), or you can synchronize a reload network-wide (for example, to perform a software upgrade on all switches in the network).
Note
Configuring a Scheduled Reload
To configure your switch to reload the software image at a later time, use one of these commands in privileged EXEC mode:
•
This command schedules a reload of the software to take affect in the specified minutes or hours and minutes. The reload must take place within approximately 24 days. You can specify the reason for the reload in a string up to 255 characters in length.
•
This command schedules a reload of the software to take place at the specified time (using a 24-hour clock). If you specify the month and day, the reload is scheduled to take place at the specified time and date. If you do not specify the month and day, the reload takes place at the specified time on the current day (if the specified time is later than the current time) or on the next day (if the specified time is earlier than the current time). Specifying 00:00 schedules the reload for midnight.
Note
The reload command halts the system. If the system is not set to manually boot, it reboots itself. Use the reload command after you save the switch configuration information to the startup configuration (copy running-config startup-config).
If your switch is configured for manual booting, do not reload it from a virtual terminal. This restriction prevents the switch from entering the boot loader mode and thereby taking it from the remote user's control.
If you modify your configuration file, the switch prompts you to save the configuration before reloading. During the save operation, the system requests whether you want to proceed with the save if the CONFIG_FILE environment variable points to a startup configuration file that no longer exists. If you proceed in this situation, the system enters setup mode upon reload.
This example shows how to reload the software on the switch on the current day at 7:30 p.m:
Switch# reload at 19:30Reload scheduled for 19:30:00 UTC Wed Jun 5 1996 (in 2 hours and 25 minutes)Proceed with reload? [confirm]This example shows how to reload the software on the switch at a future time:
Switch# reload at 02:00 jun 20Reload scheduled for 02:00:00 UTC Thu Jun 20 1996 (in 344 hours and 53 minutes)Proceed with reload? [confirm]To cancel a previously scheduled reload, use the reload cancel privileged EXEC command.
Displaying Scheduled Reload Information
To display information about a previously scheduled reload or to find out if a reload has been scheduled on the switch, use the show reload privileged EXEC command.
It displays reload information including the time the reload is scheduled to occur and the reason for the reload (if it was specified when the reload was scheduled).
