Table Of Contents
L Commands
line console
line vty
logging console
logging level
logging logfile
logging module
logging monitor
logging server
L Commands
The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric switches. All commands are shown here in alphabetical order regardless of command mode. See the "Command Modes" section to determine the appropriate mode for each command. For more information, refer to the Cisco MDS 9000 Family Configuration Guide.
•
line console
•line vty
•logging console
•logging level
•logging logfile
•logging module
•logging monitor
•logging server
line console
To configure a terminal line, use the line console command.
line console [databits number] [exec-timeout minutes] [exit] [flowcontrol none | software] [no]
[parity even | none | odd] [speed speed] [stopbits 1 | 2]
Syntax Descriptionfcdomainfcdomainfcdomainfcdomain
line console
|
Configures a primary terminal line.
|
databits
|
Set number of databits per character.
|
number
|
Enters number of databits.
|
exec-timeout
|
Configure exec timeout.
|
minutes
|
Enter timeout in minutes 0-525600. 0 to disable.
|
exit
|
Exit from this submode.
|
flowcontrol
|
Set the flow control.
|
none
|
Set no flowcontrol.
|
software
|
Set software flowcontrol.
|
no
|
Negate a command or set its defaults.
|
parity
|
Set terminal parity.
|
even
|
Set even parity.
|
none
|
Set no parity.
|
odd
|
Set odd parity.
|
speed
|
Set the transmit and receive speeds.
|
speed
|
Set transmit and receive speeds.
|
stopbits
|
Set async line stopbits.
|
1
|
Set one stop bit.
|
2
|
Set two stop bits.
|
Defaults
Disabled
Command Modes
Configuration mode.
Command History
This command was introduced in Cisco MDS SAN-OS Release 1.0(2).
Usage Guidelines
The line console command available in config t command mode. line console configuration commands available in config-console submode.
Examples
The following example configures a line console and sets the options for that terminal line.
switch(config)# line console
switch(config-console)# databits 60
switch(config-console)# exec-timeout 60
switch(config-console)# flowcontrol software
switch(config-console)# parity even
switch(config-console)# stopbits 1
Related Commands
Command
|
Description
|
line vty
|
Configure virtual terminal line.
|
line vty
To configure a virtual terminal line, use the line vty command.
line vty exec-timeout minutes | exit | no
Syntax Descriptionfcdomainfcdomainfcdomainfcdomain
line vty
|
Configures a virtual terminal line.
|
exec-timeout
|
Configure exec timeout.
|
minutes
|
Enter timeout in minutes 0-525600. 0 to disable.
|
exit
|
Exit from this submode.
|
no
|
Negate a command or set its defaults.
|
Defaults
None.
Command Modes
Configuration mode.
Command History
This command was introduced in Cisco MDS SAN-OS Release 1.0(2).
Usage Guidelines
The line vty command available in config t command mode. line vty configuration commands available in config-line submode.
Examples
The following example configures a virtual terminal line and sets the timeout for that line.
switch(config-line)# exec-timeout 60
Related Commands
Command
|
Description
|
line console
|
Configure primary terminal line.
|
logging console
To set console logging, use the logging console command.
logging console range [size bytes]
Syntax Descriptionfcdomainfcdomainfcdomainfcdomain
logging console
|
Sets console logging.
|
range
|
0-7 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
size bytes
|
Configures the size of the log file in bytes. The valid range is 4096- 4194304 bytes.
|
Defaults
Disabled.
Command Modes
Configuration mode.
Command History
This command was introduced in Cisco MDS SAN-OS Release 1.0(2).
Usage Guidelines
None.
Examples
The following example reverts console logging to the factory set default severity level of 2 (critical). Logging messages with a severity level of 2 or above will be displayed on the console.
switch(config)# logging console 2
logging level
To modify message logging facilities, use the logging level command.
logging level [ acl severity level ] [ all severity level ] [auth severity level ] [ authpriv severity
level ] [ bootvar severity level ] [ callhome severity level ] [ cron severity level ] [daemon
severity level ] [ fcc severity level ] [ fcdomain severity level ] [[fcns severity level ] [ fcs
severity level ] [ flogi severity level ] [ fspf severity level ] [ ftp severity level ] [ ipconf
severity level ] [ ipfc severity level ] [ kernel severity level ] [ local0 severity level ] [ local1
severity level ] [ local2 severity level ] [ local3 severity level ] [ local4 severity level ] [ local5
severity level ] [ local6 severity level ] [ local7 severity level ] [ mail severity level ] [ [ mcast
severity level ] [ module ] [ news ] [ ntp ] [ platform ] [ port ] [ port-channel ] [ qos ] [ rdl ]
[ rib severity level ] [ rscn severity level ] [ scsi-target severity level ] [ security severity
level ] [ syslog severity level ] [ sysmgr severity level ] [tlport severity level ] [ user severity
level ] [ uucp severity level ] [ vni severity level ] [ vrrp configuraion severity level engine
severity level ] [ vsan severity level ] [ vshd severity level ] [ wwnm severity level ] [ xbar
severity level ] [ zone severity level ]
no logging level [ acl severity level ] [ all severity level ] [auth severity level ] [ authpriv
severity level ] [ bootvar severity level ] [ callhome severity level ] [ cron severity level
] [daemon severity level ] [ fcc severity level ] [ fcdomain severity level ] [[fcns severity
level ] [ fcs severity level ] [ flogi severity level ] [ fspf severity level ] [ ftp severity level
] [ ipconf severity level ] [ ipfc severity level ] [ kernel severity level ] [ local0 severity level
] [ local1 severity level ] [ local2 severity level ] [ local3 severity level ] [ local4 severity
level ] [ local5 severity level ] [ local6 severity level ] [ local7 severity level ] [ mail severity
level ] [ [ mcast severity level ] [ module ] [ news ] [ ntp ] [ platform ] [ port ] [ port-channel
] [ qos ] [ rdl ] [ rib severity level ] [ rscn severity level ] [ scsi-target severity level ] [
security severity level ] [ syslog severity level ] [ sysmgr severity level ] [tlport severity
level ] [ user severity level ] [ uucp severity level ] [ vni severity level ] [ vrrp configuraion
severity level engine severity level ] [ vsan severity level ] [ vshd severity level ] [ wwnm
severity level ] [ xbar severity level ] [ zone severity level ]
Syntax Descriptionfcdomainfcdomainfcdomainfcdomain
logging level
|
Sets console logging.
|
acl
|
Sets 0-7 syslog filter level for acl manager. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
all
|
Sets 0-7 severity level for all facilities. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
auth
|
Sets 0-7 severity level for authorization system. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
authpriv
|
Sets 0-7 severity level for authorization (private) system. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
bootvar
|
Sets 0-7 severity level for bootvar. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
callhome
|
Sets 0-7 severity level for Callhome feature. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
cron
|
Sets 0-7 severity level l for Cron/at facility. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
daemon
|
Sets 0-7 severity level for system daemons 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
fcc
|
Sets 0-7 severity level for FCC. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
fcdomain
|
Sets 0-7 syslog message level for fcdomain. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
fcns
|
Sets 0-7 syslog filter level for name server 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
fcs
|
Sets 0-7 syslog filter level for FCS. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
flogi
|
Sets 0-7 syslog message level for flogi. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
fspf
|
Sets 0-7 syslog message level for FSPF. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
ftp
|
Sets 0-7 syslog message level for File Transfer System. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
ipconf
|
Sets 0-7 syslog message level for IP configuration. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
ipfc
|
Sets 0-7 syslog message level for IPFC. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
kernel
|
Sets 0-7 syslog message level for kernel. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
local0
|
Sets 0-7 syslog message level for local use daemons. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
local2
|
Sets 0-7 syslog message level for local use daemons. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
local3
|
Sets 0-7 syslog message level for local use daemons. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
local4
|
Sets 0-7 syslog message level for local use daemons. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
local5
|
Sets 0-7 syslog message level for local use daemons. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
local6
|
Sets 0-7 syslog message level for local use daemons. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
local7
|
Sets 0-7 syslog message level for local use daemons. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
lpr
|
Sets 0-7 syslog message level for line printer system. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
mail
|
Sets 0-7 syslog message level for mail system. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
mcast
|
Sets 0-7 syslog message level for mcast 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
module
|
Sets 0-7 syslog message level for module. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
news
|
Sets 0-7 syslog message level for USENET news 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
ntp
|
Sets 0-7 syslog message level for NTP. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
platform
|
Sets 0-7 syslog message level for platform manager. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
port
|
Sets 0-7 syslog message level for port. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
port-channel
|
Sets 0-7 syslog message level for a Port Channel. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
qos
|
Sets 0-7 syslog message level for QoS manager. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
rdl
|
Sets 0-7 syslog message level for RDL. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
rib
|
Sets 0-7 syslog message level for rib. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
rscn
|
Sets 0-7 syslog message level for RSCN. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
scsi-target
|
Sets 0-7 syslog message level for SCSI target. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
security
|
Sets 0-7 syslog message level for security. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
syslog
|
Sets 0-7 syslog message level for internal syslog messages. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
sysmgr
|
Sets 0-7 syslog message level for system manager. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
tlport
|
Sets 0-7 syslog message level for TL Port. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
user
|
Sets 0-7 syslog message level user process. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
uucp
|
Sets 0-7 syslog message level for Unix-to-Unix copy system. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
vni
|
Sets 0-7 syslog message level for virtual network interface. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
vrrp
|
Sets 0-7 syslog message level for vrrp. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
vrrp configuration
|
Sets 0-7 syslog message level 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
vrrp engine
|
Sets 0-7 syslog message level 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
vsan
|
Sets 0-7 syslog message level for VSAN. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
vshd
|
Sets 0-7 syslog message level for vshd. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
wwnm
|
Sets 0-7 syslog message level for WWN manager. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
xbar
|
Sets 0-7 syslog message level for Xbar. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
zone
|
Sets 0-7 syslog message level for for zone server. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
Defaults
Disabled
Command Modes
Configuration mode
Command History
This command was introduced in Cisco MDS SAN-OS Release 1.0(2).
Usage Guidelines
None.
Examples
Configures Telnet or SSH logging for the kernel facility at level 4 (warning). As a result, logging messages with a severity level of 4 or above will be displayed.
switch(config)# logging level kernal 4
logging logfile
To set message logging for logfile, use the logging logfile command.
logging logfile file name severity level
Syntax Descriptionfcdomainfcdomainfcdomainfcdomain
logging logfile
|
Sets message logging for logfile.
|
file name
|
Enters the logfile name.
|
severity level
|
0-7 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
Defaults
None.
Command Modes
Configuration mode.
Command History
This command was introduced in Cisco MDS SAN-OS Release 1.0(2).
Usage Guidelines
None.
Examples
The following example configures logging information for errors or events above a severity level of 3 (errors) to be logged in a file named ManagerLogFile. By configuring this limit, the file size is restricted to 3000000 bytes.
switch(config)# logging logfile ManagerLogFile 3 size 3000000
Related Commands
Command
|
Description
|
show logging logfile
|
Displays the message logging for the logfile.
|
logging module
To set message logging for linecards, use the logging module command.
logging module severity level
Syntax Descriptionfcdomainfcdomainfcdomainfcdomain
logging module
|
Sets message logging for modules.
|
severity level
|
0-7 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
Defaults
None.
Command Modes
Configuration mode.
Command History
This command was introduced in Cisco MDS SAN-OS Release 1.0(2).
Usage Guidelines
None.
Examples
The following example sets message logging for modules at level 7.
switch(config)# logging module 7
logging monitor
To set monitor message logging, use the logging monitor command.
logging monitor severity level
Syntax Descriptionfcdomainfcdomainfcdomainfcdomain
logging monitor
|
Sets message logging.
|
severity level
|
0-7 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
Defaults
None.
Command Modes
Configuration mode.
Command History
This command was introduced in Cisco MDS SAN-OS Release 1.0(2).
Usage Guidelines
None.
Examples
The following example sets terminal line (monitor) message logging at level 2.
switch(config)# logging monitor 2
Related Commands
Command
|
Description
|
show logging monitor
|
Displays the message logging for the logfile.
|
logging server
To set message logging for the remote server, use the logging server command.
logging server [ hostname | ip address severity_level | facility auth | authpriv | cron | daemon |
ftp | kernel | local0 | local1 | local2 | local3 | local4 | local5 | local6 | local7 | lpr | mail | news
| syslog | user | uucp ]
Syntax Descriptionfcdomainfcdomainfcdomainfcdomain
logging server
|
Sets message logging for remote server.
|
hostname
|
Enters host name for remote server.
|
ip address
|
Enters the IP address for the remote server.
|
severity_level
|
Enter severity level of message. 0-emerg;1-alert;2-crit;3-err;4-warn;5-notif;6-inform;7-debug
|
facility
|
Facility to use when forwarding to server
|
auth
|
Use auth facility
|
authpriv
|
Use authpriv facility
|
cron
|
Use Cron/at facility
|
daemon
|
Use daemon facility
|
ftp
|
Use file transfer system facility
|
kernel
|
Use kernel facility
|
local0
|
Use local0 facility
|
local1
|
Use local1 facility
|
local2
|
Use local2 facility
|
local3
|
Use local3 facility
|
local4
|
Use local4 facility
|
local5
|
Use local5 facility
|
local6
|
Use local6 facility
|
local7
|
Use local7 facility
|
lpr
|
Use lpr facility
|
mail
|
Use mail facility
|
news
|
Use USENET news facility
|
syslog
|
Use syslog facility
|
user
|
Use user facility
|
uucp
|
Use Unix-to-Unix copy system facility
|
Defaults
None.
Command Modes
Configuration mode.
Command History
This command was introduced in Cisco MDS SAN-OS Release 1.0(2).
Usage Guidelines
None.
Examples
Enable message logging to the specified remote server for level 7 messages.
switch(config)# logging sever sanjose 7
Related Commands
Command
|
Description
|
show logging server
|
Displays the message logging for the remote server.
|
Feedback