Cisco ONS 15454 and Cisco ONS 15327 TL1 Command Quick Reference Guide, Release 4.6
Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.
This guide lists TL1 commands and autonomous messages by category. It includes basic descriptions and input and output formats supported by the Cisco ONS 15454 and the Cisco ONS 15327, Release 4.6. Refer to the Cisco ONS 15454 and Cisco ONS 15327 TL1 Command Guide, Release 4.6 for a complete description of TL1 commands.
TL1 commands conform to the following syntax: a:b:c:d:e: ...z; where: "a" is the Command Code "b" is the Target Identifier (TID) "c" is the Access Identifier (AID) or the User Identifier (UID) "d" is the Correlation Tag (CTAG) "e: ...z;" are other positions required for various commands The TID, AID, and CTAG route and control the TL1 command. Other parameters provide additional information required to complete the action requested by the commanBLSR
Table 1 BLSR
DLT-<MOD_RING>:[<TID>]:<AID>:<CTAG>[:::]; Deletes the BLSR of the NE
ED-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,][NODEID=<NODEID>,] [RVRTV=<RVRTV>,][RVTM=<RVTM>,][SRVRTV=<SRVRTV>,][SRVTM=<SRVTM>][:]; Edits the BLSR attributes
ENT-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,]NODEID=<NODEID>, MODE=<MODE>,[RVRTV=<RVRTV>,][RVTM=<RVTM>,][SRVRTV=<SRVRTV>,] [SRVTM=<SRVTM>,]EASTWORK=<EASTWORK>,WESTWORK=<WESTWORK>, [EASTPROT=<EASTPROT>,][WESTPROT=<WESTPROT>]; Creates either a two-fiber or four-fiber BLSR
EX-SW-<OCN_BLSR>:[<TID>]:<AID>:<CTAG>::,[<SWITCHTYPE>][,<DIRECTION>]; Exercises the algorithm for switching from a working facility to a protection facility without actually performing a switch.
RTRV-<MOD_RING>:[<TID>]:[<AID>]:<CTAG>[::::]; Retrieves all of the BLSR information of the network element (NE) Output format:
SID DATE TIME M CTAG COMPLD "[<AID>]::[RINGID=<RINGID>,][NODEID=<NODEID>,][MODE=<MODE>,] [RVRTV=<RVRTV>,][RVTM=<RVTM>,][SRVRTV=<SRVRTV>,][SRVTM=<SRVTM>,] [EASTWORK=<EASTWORK>,][WESTWORK=<WESTWORK>,][EASTPROT=<EASTPROT>,] [WESTPROT=<WESTPROT>]" ;
RTRV-TRC-<OCN_BLSR>:[<TID>]:<AID>:<CTAG>; Retrieves the valid J1 expected trace string, received trace string, trace mode, C2 byte and STS bandwidth of the OCN port if the port has a BLSR. Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[LEVEL=<LEVEL>,][EXPTRC=<EXPTRC>,][INCTRC=<INCTRC>,] [TRCMODE=<TRCMODE>,][C2=<C2>]" ;
1 Cross Connections
Table 2 Cross Connections
DLT-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>[:::]; Deletes a cross-connection between STS or VT paths
ED-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>:::[ADD=<ADD>,] [REMOVE=<REMOVE>]:[<PST>],[<SST>]; Edits the state of an STS or VT cross-connection
ENT-CRS-<PATH>:[<TID>]:<AID>,<DST>:<CTAG>::[<CCT>]::[<PST>],[<SST>]; Creates an STS or VT cross-connection with cross-connection types (CCT)
RTRV-CRS:[<TID>]:<AID>:<CTAG>:::[CRSTYPE=<CRSTYPE>][:]; Retrieves all the cross-connections based on the required CRSTYPE (for all STS connections) Output format:
SID DATE TIME M CTAG COMPLD "<CROSSCONNECTID>,<CROSSCONNECTID1>:<CCT>,<MOD>::<PST>,[<SST>]" ;
RTRV-CRS-<PATH>:[<TID>]:<SRC>:<CTAG>[::::]; Retrieves any connections associated with the entered AID(s) or AID range Output format:
SID DATE TIME M CTAG COMPLD "<CROSSCONNECTID>,<CROSSCONNECTID1>:<CCT>,<MOD>::<PST>,[<SST>]" ;
2 DWDM (Cisco ONS 15454 only)
Table 3 DWDM (Cisco ONS 15454 only)
DLT-FFP-CLNT:[<TID>]:<WORKAID>,<PROTAID>:<CTAG>[:::]; Deletes Y cable protection on client facilities
DLT-LNK-<MOD2O>:[<TID>]:<FROM>,<TO>:<CTAG>; Deletes an optical link between two optical connection points.
DLT-OSC:[<TID>]:<AID>:<CTAG>; Deletes the OSC group of the NE
DLT-WLEN:[<TID>]:<AID>:<CTAG>[:::CMDMDE=<CMDMDE>]; Deletes the provisioned wavelength (WLEN)
ED-DWDM:[<TID>]:<AID>:<CTAG>:::[PEERID=<PEERID>,][NAME=<NAME>,] [TERMMODE=<TERMMODE>,][PAYLOAD=<PAYLOAD>,][PWL=<PWL>]; Edits an already pre-provisioned/provisioned MXP_2.5G_10G and TXP_MR_10G card
ED-FFP-CLNT:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,][RVRTV=<RVRTV>,] [RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:]; Edits a Y cable protection group on client facilities
ED-FFP-OCH::[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,][RVRTV=<RVRTV>,] [RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:]; Edits the provisioning for the default protection group on the DWDM port of a TXP_MR_2.5G or TXPP_MR_2.5G card
ED-LNK-<MOD2O>:[<TID>]:<FROM>,<TO>:<CTAG>::::<PST>,[<SST>]; Edits an optical link
ED-OCH:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>,][EXPWLEN=<EXPWLEN>,] [VOAATTN=<VOAATTN>,][VOAPWR=<VOAPWR>,][CALOPWR=<CALOPWR>,] [CHPOWER=<CHPOWER>,][NAME=<PORTNAME>,][SFBER=<SFBER>,][SDBER=<SDBER>,] [ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,][ALSRCPW=<ALSRCPW>,] [COMM=<COMM>,][GCCRATE=<GCCRATE>,][OSDBER=<OSDBER>,][DWRAP=<DWRAP>,] [FEC=<FEC>,][MACADDR=<MACADDR>,][SYNCMSG=<SYNCMSG>,] [SENDDUS=<SENDDUS>,][RLASER=<RLASER>,][SOAK=<SOAK>,][OSPF=<OSPF>]:[<PST>], [<SST>]; Edits the attributes (service parameters) and state of an OCH facility
ED-OMS:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>,][EXPBAND=<EXPBAND>,] [VOAATTN=<VOAATTN>,][VOAPWR=<VOAPWR>,][CALOPWR=<CALOPWR>,] [CHPOWER=<CHPOWER>]:[<PST>],[<SST>]; Edits the attributes (service parameters) and state of an OMS facility (R4.5 only)
ED-OSC:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,][NODEID=<NODEID>]; Edits the OSC (Optical Service Channel) group attributes
ED-OTS:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>,][VOAATTN=<VOAATTN>,] [VOAPWR=<VOAPWR>,][CALOPWR=<CALOPWR>,][CALTILT=<CALTILT>,][OSRI=<OSRI>,] [ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,][ALSRCPW=<ALSRCPW>,] [EXPGAIN=<EXPGAIN>]:[<PST>],[<SST>]; Edits the attributes (service parameters) and state of an OTS facility
ED-TRC-CLNT:[<TID>]:<SRC>:<CTAG>:::[EXPTRC=<EXPTRC>,][TRC=<TRC>,] [TRCMODE=<TRCMODE>,]TRCLEVEL=<TRCLEVEL>,[TRCFORMAT=<TRCFORMAT>][:]; Edits trace-related attributes on client facilities
ENT-FFP-CLNT:[<TID>]:<WORKAID>,<PROTAID>:<CTAG>:::[PROTTYPE=<PROTTYPE>,] [PROTID=<PROTID>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:]; Creates Y cable protection on client facilities
ENT-LNK-<MOD2O>:[<TID>]:<FROM>,<TO>:<CTAG>::::<PST>,[<SST>]; Creates an optical link between two optical connection points
ENT-OSC:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>,]NODEID=<NODEID>, [EAST=<EAST>,][WEST=<WEST>]; Creates the OSC (optical service channel) group of the NE
ENT-WLEN:[<TID>]:<AID>:<CTAG>:::[SIZE=<SIZE>]:[<PST>],[<SST>]; Allocates a wavelength
OPR-LASER-OTS:[<TID>]:<AID>:<CTAG>; Instructs a laser to be switched on
OPR-LNK:[<TID>]::<CTAG>; Permits the optical link application inside the NE to calculate all the automatic optical links between end points which can be univocally identified by the NE
OPR-PROTNSW-CLNT:[<TID>]:<AID>:<CTAG>::<SC>[:]; Operates a Y cable protection switch request
OPR-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>[::]; Performs a protection switch on the trunk port of a TXPP_MR_2.5G card
OPR-WDMANS:[<TID>]::<CTAG>; Operates the Automatic Optical Node Setup (AONS) application inside the NE to force a recompute of the value to be assigned to all VOAs representing the Optical Path inside the node
RLS-LASER-OTS:[<TID>]:<AID>:<CTAG>; Instructs a laser to be switched off
RLS-PROTNSW-CLNT:[<TID>]:<AID>:<CTAG>[::]; Releases a Y cable protection switch on client facilities
RLS-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>[::]; Performs a protection switch on the trunk port of a TXPP_MR_2.5G card
RTRV-ALMTH-<MOD2>:[<TID>]:<AID>:<CTAG>::<ALMTHR>[,,::]; Retrieves the alarm threshold values Output format:
SID DATE TIME M CTAG COMPLD "<AID>,<MOD>:<CONDTYPE>,,,<THLEVEL>" ;
SID DATE TIME M CTAG COMPLD "<AID>:,,[<ROLE>],<STATUS>:[NAME=<PORTNAME>,][COMM=<COMM>,] [SFBER=<SFBER>,][SDBER=<SDBER>,][ALSMODE=<ALSMODE>,] [ALSRCINT=<ALSRCINT>,][ALSRCPW=<ALSRCPW>,][SYNCMSG=<SYNCMSG>,] [SENDDUS=<SENDDUS>,][LSRSTAT=<LSRSTAT>,][CLEI=<CLEI>,][PN=<PARTNUM>,] [SN=<SERIALNUM>,][VENDORREV=<VENDORREV>,][PLGTYPE=<PLGTYPE>,] [MACADDR=<MACADDR>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,] [OSPF=<OSPF>]:<PST>,[<SST>]" ;
SID DATE TIME M CTAG COMPLD "<AID>:<EQPTTYPE>,<EQUIP>,,[<STATUS>]:[PEERID=<PEERID>,][NAME=<NAME>,] [TERMMODE=<TERMMODE>,][PAYLOAD=<PAYLOAD>,][CARDNAME=<CARDNAME>,] [PWL=<PWL>,][TWL1=<TWL>,][TWL2=<TWL1>,][TWL3=<TWL2>,][TWL4=<TWL3>]: [<PST>],[<SST>]" ;
RTRV-FFP-CLNT:[<TID>]:<AID>:<CTAG>[::::]; Retrieves Y cable protection on client facilities Output format:
SID DATE TIME M CTAG COMPLD "<WORKAID>,<PROTAID>::[PROTTYPE=<PROTTYPE>,][PROTID=<PROTID>,] [RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>]" ;
RTRV-FFP-OCH:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the protection group information for the TXP_MR_2.5G and TXPP_MR_2.5G trunk port Output format:
SID DATE TIME M CTAG COMPLD "<WORK>,<PROTECT>::[PROTTYPE=<PROTTYPE>,][PROTID=<PROTID>,] [RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>]" ;
RTRV-LNK:[<TID>]::<CTAG>; Retrieves all the optical links created in the NE Output format:
SID DATE TIME M CTAG COMPLD "<FROM>,<TO>::[OLNKT=<OLNKT>,][CTYPE=<CTYPE>,][RDIRN=<RDIRN>,] [BAND=<BAND>,][WLEN=<WLEN>]:<PST>,[<SST>]" ;
RTRV-LNK-<MOD2O>:[<TID>]:<AID>:<CTAG>:::[OLNKT=<OLNKT>,][CTYPE=<CTYPE>,] [RDIRN=<RDIRN>]; Retrieves any optical link associated with the entered AIDs or AID range Output format:
SID DATE TIME M CTAG COMPLD "<FROM>,<TO>::[OLNKT=<OPTICALLINKTYPE>,][CTYPE=<CREATIONTYPE>,] [RDIRN=<RDIRN>,][BAND=<BAND>,][WLEN=<WLEN>]:<PST>,[<SST>]"
;
RTRV-NE-WDMANS:[<TID>]::<CTAG>; Retrieves the optical nodes setup (WDMANS) application ports involved in node setup regulation Output format:
SID DATE TIME M CTAG COMPLD "<AID>,<AIDTYPE>::[REGULATED=<REGULATED>]" ;
RTRV-OCH:[<TID>]:<AID>:<CTAG>; Retrieves the attributes (service parameters) and state of an OCH facility Output format:
SID DATE TIME M CTAG COMPLD "<AID>:,,[<ROLE>],[<STATUS>]:[RDIRN=<RDIRN>,][OPTYPE=<OPTICALPORTTYPE>,] [OPWR=<POWER>,][EXPWLEN=<EXPWLEN>,][ACTWLEN=<ACTWLEN>,] [ILOSS=<ILOSS>,][VOAMODE=<VOAMODE>,][VOAATTN=<VOAATTN>,] [VOAPWR=<VOAPWR>,][VOAREFATTN=<VOAREFATTN>,] [VOAREFPWR=<VOAREFPWR>,][REFOPWR=<REFOPWR>,][CALOPWR=<CALOPWR>,] [CHPOWER=<CHPOWER>,][NAME=<PORTNAME>,][SFBER=<SFBER>,][SDBER=<SDBER>,] [ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,][ALSRCPW=<ALSRCPW>,] [COMM=<COMM>,][GCCRATE=<GCCRATE>,][DWRAP=<DWRAP>,][FEC=<FEC>,] [OSFBER=<OSFBER>,][OSDBER=<OSDBER>,][MACADDR=<MACADDR>,] [SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,][LSRSTAT=<LSRSTAT>,] [SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,][OSPF=<OSPF>]:<PST>,[<SST>]" ;
RTRV-OMS:[<TID>]:<AID>:<CTAG>; Retrieves the attributes (service parameters) and state of an OMS facility Output format:
SID DATE TIME M CTAG COMPLD "<AID>::RDIRN=<RDIRN>,OPTYPE=<OPTICALPORTTYPE>,[OPWR=<POWER>,] EXPBAND=<EXPBAND>,[ACTBAND=<ACTBAND>,][ILOSS=<ILOSS>,] [VOAMODE=<VOAMODE>,][VOAATTN=<VOAATTN>,][VOAPWR=<VOAPWR>,] [VOAREFATTN=<VOAREFATTN>,][VOAREFPWR=<VOAREFPWR>,] [REFOPWR=<REFOPWR>,][CALOPWR=<CALOPWR>,][CHPOWER=<CHPOWER>]:<PST>, [<SST>]" ;
RTRV-OSC:[<TID>]:<AID>:<CTAG>; Retrieves all of the OSC (optical service channel) information of the NE Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[RINGID=<RINGID>,][NODEID=<NODEID>,][EAST=<EAST>,][WEST=<WEST>]" ;
RTRV-OTS:[<TID>]:<AID>:<CTAG>; Retrieves the attributes (service parameters) and state of an OTS facility Output format:
SID DATE TIME M CTAG COMPLD "<AID>:RDIRN=<RDIRN>,OPTYPE=<OPTICALPORTTYPE>,[OPWR=<POWER>,] [ILOSS=<ILOSS>,][VOAMODE=<VOAMODE>,][VOAATTN=<VOAATTN>,] [VOAPWR=<VOAPWR>,][VOAREFATTN=<VOAREFATTN>,] [VOAREFPWR=<VOAREFPWR>,][LASERST=<LASERST>,][OSRI=<OSRI>,] [ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,][ALSRCPW=<ALSRCPW>,] [AMPLMODE=<AMPLMODE>,][GAIN=<GAIN>,][EXPGAIN=<EXPGAIN>,] [REFOPWR=<REFOPWR>,][CALOPWR=<CALOPWR>,][REFTILT=<REFTILT>,] [CALTILT=<CALTILT>,][DCULOSS=<DCULOSS>,][AWGST=<AWGST>,] [HEATST=<HEATST>]:<PST>,[<SST>]" ;
RTRV-PROTNSW-CLNT:[<TID>]:<AID>:<CTAG>[::::]; Retrieves protection switch status of client facilities Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<SC>,[<SWITCHTYPE>]" ;
RTRV-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>; Retrieves protection switch status of a TXPP_MR_2.5G card Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<SW>,<SWTYPE>" ;
RTRV-TRC-CLNT:[<TID>]:<SRC>:<CTAG>::[<MSGTYPE>],[<TRCLEVEL>][::]; Retrieves the SONET J0 Section sent trace string, expected trace string, received trace string, trace mode, and the trace level for the client facility Output format:
SID DATE TIME M CTAG COMPLD "<AID>,<MOD>::[TRCLEVEL=<TRCLEVEL>,][EXPTRC=<EXPTRC>,][TRC=<TRC>,] [INCTRC=<INCTRC>,][TRCMODE=<TRCMODE>,][TRCFORMAT=<TRCFORMAT>]" ;
RTRV-TRC-OCH:[<TID>]:<SRC>:<CTAG>::[<MSGTYPE>],[<TRCLEVEL>][::]; Retrieves the sent trace string, expected trace string, received trace string, trace mode, and the trace level for the SONET J0 Section, the TTI PATH and SECTION monitoring levels of the DWDM facility Output format:
SID DATE TIME M CTAG COMPLD "<CHANNEL>,<MOD>::[TRCLEVEL=<TRCLEVEL>,][EXPTRC=<EXPTRC>,][TRC=<TRC>,] [INCTRC=<INCTRC>,][TRCMODE=<TRCMODE>,][TRCFORMAT=<TRCFORMAT>]" ;
RTRV-ATTR-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>]; Retrieves attributes associated with an external control
Output format:
SID DATE TIME M CTAG COMPLD "<AID>:[<CONTTYPE>]" ;
RTRV-ATTR-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>]; Retrieves attributes associated with an environmental alarm
Output format:
SID DATE TIME M CTAG COMPLD "<AID>:[<NTFCNCDE>],[<ALMTYPE>],[<DESC>]" ;
SET-ATTR-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>]; Sets attributes associated with an external control
SET-ATTR-ENV:[<TID>]:<AID>:<CTAG>::<NTFCNCDE>,<ALMTYPE>,<ALMMSG>; Sets attributes associated with an external control
4 Environment Alarms and Controls
Table 5 Environment Alarms and Controls
OPR-ACO-ALL:[<TID>]::<CTAG>; Operates the cut-off of the office audible alarm indications without changing the local alarm indications
OPR-EXT-CONT:[<TID>]:<AID>:<CTAG>::[<CONTTYPE>],[<DURATION>]; Operates an external control and closes the external control contact
REPT ALM ENV Reports a user-defined condition on an environmental alarm input
REPT EVT ENV Reports a non-alarmed event against an environment alarm input
RLS-EXT-CONT:[<TID>]:<AID>:<CTAG>[::,]; Releases a forced contact state and returns the control of the contact to an automatic control state
RTRV-ALM-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>]; Retrieves the environmental alarms Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<NTFCNCDE>,<ALMTYPE>,,,[<DESC>]" ;
RTRV-COND-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>][,,,]; Retrieves the environmental conditions Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],,,,[<DESC>]" ;
RTRV-EXT-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>]; Retrieves the control state of an external control Output format:
SID DATE TIME M CTAG COMPLD "<AID>:[<CONTTYPE>],<DUR>,[<CONTSTATE>]" ;
5 Equipment
Table 6 Equipment
ALW-SWDX-EQPT:[<TID>]:<AID>:<CTAG>[::]; Allows automatic or manual switching on a duplex system containing duplexed or redundant equipment (Cisco ONS 15454 only)
ALW-SWTOPROTN-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>]; Allows automatic or manual switching of an equipment unit back to a protection status (Cisco ONS 15454 only)
ALW-SWTOWKG-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>]; Allows automatic or manual switching of an equipment unit back to a working status (Cisco ONS 15454 only)
DLT-EQPT:[<TID>]:<AID>:<CTAG>[:::]; Deletes a card from the NE
ED-EQPT:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,] [PRTYPE=<PRTYPE>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,][CMDMDE=<CMDMDE>][:]; Edits the attributes for a given equipment slot in the NE
ENT-EQPT:[<TID>]:<AID>:<CTAG>::<AIDTYPE>:[PROTID=<PROTID>,] [PRTYPE=<PRTYPE>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,][CMDMDE=<CMDMDE>][:]; Enters the card type and attributes for a given equipment slot in the NE
INH-SWDX-EQPT:[<TID>]:<AID>:<CTAG>[::]; Inhibits the automatic or manual switching on an NE containing duplex equipment (Cisco ONS 15454 only)
INH-SWTOPROTN-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>]; Inhibits automatic or manual switching of an equipment unit to protection (Cisco ONS 15454 only)
INH-SWTOWKG-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>]; Inhibits automatic or manual switching of an equipment unit back to the working unit (Cisco ONS 15454 only)
REPT ALM EQPT Reports an alarm condition against an equipment unit or slot
REPT EVT EQPT Reports the occurrence of a non-alarmed event against an equipment unit or slot
RTRV-ALM-EQPT:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>], [<SRVEFF>][,,,]; Retrieves and sends the current status of alarm conditions associated with the equipment units Output format:
SID DATE TIME M CTAG COMPLD "[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]" ;
RTRV-ALMTH-EQPT:[<TID>]::<CTAG>::<ALMTHR>[,,::]; Retrieves the alarm thresholds for the power level monitoring Output format:
SID DATE TIME M CTAG COMPLD ",<MOD2B>:<ALMTHR>,,,<DNFIELD>" ;
RTRV-COND-EQPT:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the equipment conditions Output format:
SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;
RTRV-EQPT:[<TID>]:<AID>:<CTAG>[::::]; Retrieves protection group information and status information for all cards Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<AIDTYPE>,<EQUIP>,[<ROLE>],[<STATUS>]:[PROTID=<PROTID>,] [PRTYPE=<PRTYPE>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,] [CARDNAME=<CARDNAME>,][IOSCFG=<IOSCFG>]:[<PST>],[<SST>]" ;
SW-DX-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>][,]; Switches an XC/XCVT/XC10G card with the mate card within the NE (Cisco ONS 15454 only)
SW-TOPROTN-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>],[<PROTID>],[<DIRN>]; Performs an equipment unit protection switch (Cisco ONS 15454 only)
SW-TOWKG-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>],[<DIRN>]; Switches the protected working unit back to the working unit (Cisco ONS 15454 only)
6 Fault
Table 7 Fault
REPT ALM <MOD2ALM> Reports an alarm condition against a facility or a path
REPT ALM COM Reports an alarm condition when an AID cannot be given
REPT EVT <MOD2ALM> Reports the occurrence of a non-alarmed event
REPT EVT COM Reports a non-alarmed event against an NE when there is no AID associated with it
RTRV-ALM-ALL:[<TID>]::<CTAG>::[<NTFCNCDE>],[<CONDITION>],[<SRVEFF>][,,,]; Retrieves and sends the current status of all active alarm conditions Output format:
SID DATE TIME M CTAG COMPLD "[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>],[<AIDDET>]" ;
RTRV-COND-<MOD2ALM>:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the current standing condition and/or state associated with an entity Output format:
SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;
RTRV-COND-ALL:[<TID>]::<CTAG>::[<TYPEREQ>][,,,]; Retrieves the current standing condition for all entities Output format:
SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;
7 File Transfer
Table 8 File Transfer
APPLY:[<TID>]::<CTAG>[::<MEM_SW_TYPE>]; Activates or reverts a software load during a software upgrade or downgrade
COPY-RFILE:[<TID>]:[<SRC>]:<CTAG>::TYPE=<XFERTYPE>,[SRC=<SRC1>,] [DEST=<DEST>,][OVWRT=<OVWRT>,][FTTD=<FTTD>]; Downloads a new software package from the location specified by the FTP URL
REPT EVT FXFR Reports the FTP software download status of the start, completion and completed percentage
8 IOS
Table 9 IOS
COPY-IOSCFG:[<TID>]:<AID>:<CTAG>::SRC=<SRC>,DEST=<DEST>; Uploads startup IOS configuration files from the network to the node and downloads startup IOS configuration files from the node to the network (ML-series Ethernet cards) (Cisco ONS 15454 only)
REPT EVT IOSCFG Reports the status of copying the IOS configuration file when the COPY-IOSCFG command is issued (Cisco ONS 15454 only)
REPT DBCHG Reports any changes on the NE that result from certain TL1 commands or an external event
RTRV-LOG:[<TID>]::<CTAG>::<LOGNM>; Retrieves the alarm log of the NE Output format:
SID DATE TIME M CTAG COMPLD "<AID>,<ALMNUMBER>:CURRENT=<CURRENT>,[PREVIOUS=<PREVIOUS>,] <CONDITION>,<SRVEFF>,[TIME=<OCRTIME>,][DATE=<OCRDAT>]:<ALMDESCR>" ;
10 Network
Table 11 Network
RTRV-MAP-NETWORK:[<TID>]::<CTAG>; Retrieves all the NE attributes which are reachable from the GNE Output format:
SID DATE TIME M CTAG COMPLD "<IPADDR>,<NODENAME>,<PRODUCT>" ;
RTRV-NE-IPMAP:[<TID>]:[<AID>]:<CTAG>; Retrieves the IP address and node name of the NEs that have the DCC connection with this NE Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<IPADDR>,<NODENAME>" ;
11 Paths
Table 12 Paths
ED-<MOD_PATH>:[<TID>]:<AID>:<CTAG>:::[SFBER=<SFBER>,][SDBER=<SDBER>,] [RVRTV=<RVRTV>,][RVTM=<RVTM>,][SWPDIP=<SWPDIP>,] [HOLDOFFTIMER=<HOLDOFFTIMER>,][EXPTRC=<EXPTRC>,][TRC=<TRC>,] [TRCMODE=<TRCMODE>,][TACC=<TACC>,][TAPTYPE=<TAPTYPE>]:[<PST>],[<SST>]; Edits the attributes associated with an STS or VT path
RTRV-<PATH>:[<TID>]:<AID>:<CTAG>:::[BLSRPTHTYPE=<BLSRPTHTYPE>][:]; Retrieves the attributes associated with an STS or VT path Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[LEVEL=<LEVEL>,][SFBER=<SFBER>,][SDBER=<SDBER>,][RVRTV=<RVRTV>,] [RVTM=<RVTM>,][SWPDIP=<SWPDIP>,][HOLDOFFTIMER=<HOLDOFFTIMER>,] [EXPTRC=<EXPTRC>,][TRC=<TRC>,][INCTRC=<INCTRC>,][TRCMODE=<TRCMODE>,] [TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][UPSRPTHSTATE=<UPSRPTHSTATE>,][C2=<C2>,] [BLSRPTHSTATE=<BLSRPTHSTATE>]:[<PST>],[<SST>]" ;
RTRV-STS:[<TID>]:<AID>:<CTAG>; Retrieves the attributes associated with an STS path based on the granularity level of NE/SLOT-specific STSs Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[LEVEL=<LEVEL>,][SFBER=<SFBER>,][SDBER=<SDBER>,][RVRTV=<RVRTV>,] [RVTM=<RVTM>,][SWPDIP=<SWPDIP>,][HOLDOFFTIMER=<HOLDOFFTIMER>,] [EXPTRC=<EXPTRC>,][TRC=<TRC>,][INCTRC=<INCTRC>,][TRCMODE=<TRCMODE>,] [TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][UPSRPTHSTATE=<UPSRPTHSTATE>,] [C2=<C2>,][BLSRPTHSTATE=<BLSRPTHSTATE>]:[<PST>],[<SST>]" ;
12 Performance
Table 13 Performance
ALW-PMREPT-ALL:[<TID>]::<CTAG>; Resumes processing all the PM reports that are inhibited
INH-PMREPT-ALL:[<TID>]::<CTAG>; Inhibits all scheduled PM reporting
INIT-REG-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,,[<LOCN>],[<DIRN>], [<TMPER>][,,]; Initializes the performance monitoring (PM) registers
REPT PM <MOD2> Reports of performance monitoring statistics as a result of schedule created by SCHED-PMREPT
RTRV-PM-<MOD2>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>],[<MONLEV>],[<LOCN>], [<DIRN>],[<TMPER>],[<DATE>],[<TIME>]; Retrieves the values of PM parameters for a specified card type Output format:
SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<MONTYPE>,<MONVAL>,[<VLDTY>],[<LOCN>],[<DIRN>], [<TMPER>],[<MONDAT>],[<MONTM>]" ;
RTRV-PMMODE-<STS_PATH>:[<TID>]:<SRC>:<CTAG>::<LOCN>; Retrieves the PM mode that has been previously set in the NE data collection Output format:
SID DATE TIME M CTAG COMPLD "<CROSSCONNECTID>:[<LOCN>],<MODETYPE>" ;
RTRV-PMSCHED-<MOD2>:[<TID>]:<AID>:<CTAG>; Retrieves the PM reporting schedule that was set for the NE by SCHED-PMREPT Output format:
SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<REPTINVL>,<REPTDAT>,<REPTTM>,[<NUMINVL>],, [<MONLEV>],<LOCN>,,[<TMPER>],[<TMOFST>],[<INHMODE>]" ;
RTRV-PMSCHED-ALL:[<TID>]::<CTAG>; Retrieves all the PM reporting schedules that were set for the NE by SCHED-PMREPT Output format:
SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<REPTINVL>,<REPTDAT>,<REPTTM>,[<NUMINVL>],, [<MONLEV>],<LOCN>,,[<TMPER>],<TMOFST>,[<INHMODE>]" ;
RTRV-TH-<MOD2>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>],[<LOCN>],<TMPER>[::]; Retrieves the current threshold level of one or more monitored parameters Output format:
SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<MONTYPE>,[<LOCN>],,<THLEV>,[<TMPER>]" ;
RTRV-TH-ALL:[<TID>]::<CTAG>::[<MONTYPE>],[<LOCATION>],[<TMPER>][::]; Retrieves the current threshold level of all monitored parameters Output format:
SID DATE TIME M CTAG COMPLD "<AID>,<AIDTYPE>:<MONTYPE>,<LOCATION>,,<THLEV>,<TMPER>" ;
SCHED-PMREPT-<MOD2>:[<TID>]:<SRC>:<CTAG>::[<REPTINVL>], [<REPTSTATM>],[<NUMREPT>],,[<MONLEV>],[<LOCN>],,[<TMPER>],[<TMOFST>]; Schedules/reschedules the NE to report the performance monitoring data for a line facility or for an STS/VT path periodically, using an automatic REPT PM message
SET-TH-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,<THLEV>,[<LOCN>],,[<TMPER>]; Sets the threshold for PM and sets the alarm thresholds for the MXP_2.5G_10G and TXP_MR_10G cards
13 Ports
Table 14 Ports
ED-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>:::[DCC=<DCC>,][AREA=<AREA>,] [SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,][PJMON=<PJMON>,][SFBER=<SFBER>,][SDBER=<SDBER>,][MODE=<MODE>,][MUX=<MUX>,][SOAK=<SOAK>,][OSPF=<OSPF>,] [LDCC=<LDCC>,][ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,] [ALSRCPW=<ALSRCPW>,][RLASER=<RLASER>]:[<PST>],[<SST>]; Edits the attributes and state of an OC-N facility
ED-DS1:[<TID>]:<AID>:<CTAG>:::[TACC=<TACC>,][TAPTYPE=<TAPTYPE>]; Edits the test access attributes for DS1 access on a DS3XM card (Cisco ONS 15454 only)
ED-EC1:[<TID>]:<AID>:<CTAG>:::[PJMON=<PJMON>,][LBO=<LBO>,][SOAK=<SOAK>,] [SFBER=<SFBER>,][SDBER=<SDBER>]:[<PST>],[<SST>]; Edits the attributes of an EC1 (Cisco ONS 15454 only)
Edits the attributes related with the fiber channel facility
ED-G1000:[<TID>]:<AID>:<CTAG>:::[MFS=<MFS>,][FLOW=<FLOW>,] [LOWMRK=<LOWMRK>,][HIWMRK=<HIWMRK>]:[<PST>],[<SST>]; Edits the attributes related to a G1000 port
ED-T1:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>,][FMT=<FMT>,][LBO=<LBO>,] [TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][SOAK=<SOAK>,][SFBER=<SFBER>,] [SDBER=<SDBER>]:[<PST>],[<SST>]; Edits the attributes related a DS1/T1 port
ED-T3:[<TID>]:<AID>:<CTAG>:::[FMT=<FMT>,][LINECDE=<LINECDE>,][LBO=<LBO>,] [INHFELPBK=<INHFELPBK>,][TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][SOAK=<SOAK>,] [SFBER=<SFBER>,][SDBER=<SDBER>]:[<PST>],[<SST>]; Edits the attributes related to a DS3/T3 port
RMV-<MOD2_IO>:[<TID>]:<AID>:<CTAG>::[<CMDMODE>],[<PST>],[<SST>]; Removes a facility from service
RST-<MOD2_IO>:[<TID>]:<AID>:<CTAG>[::]; Provisions a facility in service
RTRV-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the attributes and state of an OC-N facility Output format:
SID DATE TIME M CTAG COMPLD "<AID>:,,[<ROLE>],[<STATUS>]:[DCC=<DCC>,][AREA=<AREA>,][TMGREF=<TMGREF>,] [SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,][PJMON=<PJMON>,][SFBER=<SFBER>,][SDBER=<SDBER>,][MODE=<MODE>,][WVLEN=<WVLEN>,][RINGID=<RINGID>,] [BLSRTYPE=<BLSRTYPE>,][MUX=<MUX>,][UNIC=<UNIC>,][CCID=<CCID>,] [NBRIX=<NBRIX>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,][SSMRCV=<SSMRCV>,] [OSPF=<OSPF>,][LDCC=<LDCC>,][ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,] [ALSRCPW=<ALSRCPW>]:<PST>,[<SST>]" ;
RTRV-DS1:[<TID>]:<SRC>:<CTAG>[::::]; Retrieves the test access attributes on a DS1 layer of DS3XM card (Cisco ONS 15454 only) Output format:
SID DATE TIME M CTAG COMPLD "<DS1AID>::[TACC=<TACC>,][TAPTYPE=<TAPTYPE>]" ;
RTRV-EC1:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the facility status of an EC1 card (Cisco ONS 15454 only) Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[PJMON=<PJMON>,][LBO=<LBO>,][RXEQUAL=<RXEQUAL>,][SOAK=<SOAK>,] [SOAKLEFT=<SOAKLEFT>,][SFBER=<SFBER>,][SDBER=<SDBER>]:<PST>,[<SST>]" ;
RTRV-FC:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the attributes related with the fiber channel port Output format:
SID DATE TIME M CTAG COMPLD "<AID>::PAYLOAD=<PAYLOAD>,LINKRATE=<LINKRATE>,LINKSTATE=<LINKSTATE>, LINKRCVRY=<LINKRCVRY>:<PST>,[<SST>" ;
RTRV-FSTE:[<TID>]:<AID>:<CTAG>; Retrieves the front end port information of the ML100T-12 Ethernet card Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,] [MTU=<MTU>,][FLOWCTRL=<FLOWCTRL>,][DUPLEX=<DUPLEX>,][SPEED=<SPEED>]" ;
RTRV-G1000:[<TID>]:<AID>:<CTAG>; Retrieves the G1000 facilities configuration Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[MFS=<MFS>,][FLOW=<FLOW>,][LAN=<LAN>,][OPTICS=<OPTICS>,] [TRANS=<TRANS>,][TPORT=<TPORT>,][LOWMRK=<LOWMRK>,] [HIWMRK=<HIWMRK>]:[<PST>],[<SST>]" ;
RTRV-GIGE:[<TID>]:<AID>:<CTAG>; Retrieves the front end port information for the ML1000-2 Ethernet card Output format:
SID DATE TIME M CTAG COMPLD "AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,][MTU=<MTU>,] [FLOWCTRL=<FLOWCTRL>,][OPTICS=<OPTICS>,][DUPLEX=<DUPLEX>,] [SPEED=<SPEED>]" ;
RTRV-POS:[<TID>]:<AID>:<CTAG>; Retrieves the back end port information for the ML-series Ethernet cards when the back end port is working in POS mode Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,][MTU=<MTU>]" ;
RTRV-T1:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the DS1 facilities configuration Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[LINECDE=<LINECDE>,][FMT=<FMT>,][LBO=<LBO>,][TACC=<TAP>,] [TAPTYPE=<TAPTYPE>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,][SFBER=<SFBER>,] [SDBER=<SDBER>]:<PST>,[<SST>]" ;
RTRV-T3:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the facilities properties of a DS3 and DS3XM card Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[FMT=<FMT>,][LINECDE=<LINECDE>,][LBO=<LBO>,] [INHFELPBK=<INHFELPBK>,][TACC=<TAP>,][TAPTYPE=<TAPTYPE>,] [SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,][SFBER=<SFBER>,] [SDBER=<SDBER>]:<PST>,[<SST>]" ;
14 Security
Table 15 Security
ACT-USER:[<TID>]:<UID>:<CTAG>::<PID>; Sets up a session with the NE
ALW-MSG-SECU:[<TID>]::<CTAG>; Allows REPT EVT SECU and REPT ALM SECU
ALW-USER-SECU:[<TID>]::<CTAG>::<UID>; Enables a user ID that has been disabled (e.g., via the INH-USER-SECU command) so the user can establish a session with the NE
CANC Reports the occurrence of a session timeout event Output format:
SID DATE TIME A ATAG CANC "<UID>" ;
CANC-USER:[<TID>]:<USERID>:<CTAG>; Logs a user out of an active session with the NE
DLT-USER-SECU:[<TID>]:<UID>:<CTAG>; Deletes a user; can only be performed by a Superuser
ED-CMD-SECU:[<TID>]:<AID>:<CTAG>::<CAP>; Edits the command security level of a particular command
ED-PID:[<TID>]:<UID>:<CTAG>::<OLDPID>,<NEWPID>; Allows a user to change his or her own password
ED-USER-SECU:[<TID>]:<UID>:<CTAG>::[<NEWUID>],[<NEWPID>],,[<UAP>][:]; Edits a user's privileges, password, or ID and can only be performed by a Superuser
ENT-USER-SECU:[<TID>]:<UID>:<CTAG>::<PID>,,<UAP>[:]; Adds a user account; can only be performed by a Superuser
INH-MSG-SECU:[<TID>]::<CTAG>; Inhibits the REPT EVT SECU and REPT ALM SECU messages
INH-USER-SECU:[<TID>]::<CTAG>::<UID>; Disables (without deleting) a userid, so the user is denied access to the NE
REPT ALM SECU Reports the occurrence of an alarmed security event against the NE
REPT EVT SECU Reports the occurrence of a non-alarmed security event against the NE
REPT EVT SESSION Reports a non-alarmed event related to establishing a session with the NE
RTRV-CMD-SECU:[<TID>]:<AID>:<CTAG>; Retrieves the current command security level of the command specified in the AID field Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<CAP>" ;
RTRV-DFLT-SECU:[<TID>]:<AID>:<CTAG>; Retrieves the system-wide default values associated with several security parameters Output format:
SID DATE TIME M CTAG COMPLD "<NE>:PAGE=<PAGE>,PCND=<PCND>,MXINV=<MXINV>,DURAL=<DURAL>, TMOUT=<TMOUT>,UOUT=<UOUT>,PFRCD=<PFRCD>,POLD=<POLD>,PINT=<PINT>, LOGIN=<LOGIN>,PRIVLVL=<UAP>" ;
RTRV-USER-SECU:[<TID>]:<UID>:<CTAG>; Retrieves the security information of a specified user or list of users Output format:
SID DATE TIME M CTAG COMPLD "<UID>:,<PRIVILEGE>:LOGGEDIN=<LOGGEDIN>,[NUMSESSIONS=<NUMSESS>,] [LOCKEDOUT=<LOCKEDOUT>,][DISABLED=<DISABLED>]" ;
SET-ATTR-SECUDFLT:[<TID>]::<CTAG>::[PAGE=<PAGE>,][PCND=<PCND>,] [MXINV=<MXINV>,][DURAL=<DURAL>,][TMOUT=<TMOUT>,][UOUT=<UOUT>,] [PFRCD=<PFRCD>,][POLD=<POLD>,][PINT=<PINT>,][LOGIN=<LOGIN>,][PRIVLVL=<UAP>]; Sets the system-wide default values associated with several security parameters
15 SONET Line Protection
Table 16 SONET Line Protection
DLT-FFP-<OCN_TYPE>:[<TID>]:<WORK>,<PROTECT>:<CTAG>[:::]; Deletes an OCN facility protection group in a 1+1 architecture
ED-FFP-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>,][RVRTV=<RVRTV>,] [RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:]; Edits the optical facility protection
ENT-FFP-<OCN_TYPE>:[<TID>]:<WORK>,<PROTECT>:<CTAG>:::[PROTID=<PROTID>,] [RVRTV=<RVRTV>,][RVTM=<RVTM>,][PSDIRN=<PSDIRN>][:]; Creates an optical 1+1 protection
OPR-PROTNSW-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>::<SW>,[<SWITCHTYPE>] [:<DIRECTION>]; Initiates a SONET line protection switch request
RLS-PROTNSW-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>[::<DIRECTION>]; Releases a SONET line protection switch request
RTRV-FFP-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the optical facility protection information Output format:
SID DATE TIME M CTAG COMPLD "<WORK>,<PROTECT>::[PROTID=<PROTID>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,] [PSDIRN=<PSDIRN>]" ;
RTRV-PROTNSW-<OCN_TYPE>:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the switching state of a SONET line specified in the AID Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<SC>,[<SWITCHTYPE>]" ;
16 Switch
Table 17 Switch
RTRV-PROTNSW-<PATH>:[<TID>]:<SRC>:<CTAG>[::::]; Retrieves the switching state of a SONET path protection STS path specified in the AID Output format:
SID DATE TIME M CTAG COMPLD "<CROSSCONNECTID>:<SC>,[<SWITCHTYPE>]" ;
17 Synchronization
Table 18 Synchronization
ED-BITS:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>,][FMT=<FMT>,][LBO=<LBO>,] [SYNCMSG=<SYNCMSG>,][AISTHRSHLD=<AISTHRSHLD>,][SABIT=<SABIT>,] [IMPEDANCE=<IMPEDANCE>][:<PST>]; Edits the BITS reference attributes
ED-NE-SYNCN:[<TID>]::<CTAG>:::[TMMD=<TMMD>,][SSMGEN=<SSMGEN>,] [QRES=<QRES>,][RVRTV=<RVRTV>,][RVTM=<RVTM>]; Edits the synchronization attributes of the NE
ED-SYNCN:[<TID>]:<AID>:<CTAG>:::[PRI=<PRI>,][SEC=<SEC>,][THIRD=<THIRD>][:]; Edits the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock
OPR-SYNCNSW:[<TID>]:[<AID>]:<CTAG>::<SWITCHTO>,[<SC>]; Initiates a switch to the reference specified by the synchronization reference number if the reference supplied is valid
REPT ALM BITS Reports an alarm condition on a BITS facility
REPT ALM SYNCN Reports an alarm condition against a synchronization reference
REPT EVT BITS Reports the occurrence of a non-alarmed event against a BITS facility
REPT EVT SYNCN Reports the occurrence of a non-alarmed event against a synchronization entity
RLS-SYNCNSW:[<TID>]:[<AID>]:<CTAG>; Releases the previous synchronization reference provided by the OPR-SYNCNSW command
RTRV-ALM-BITS:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>][,,,]; Retrieves and sends the current status of alarm conditions associated with the BITS facility Output format:
SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]" ;
RTRV-ALM-SYNCN:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>], [<SRVEFF>][,,,]; Retrieves and sends the current status of alarm conditions associated with a synchronization facility Output format:
SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]" ;
RTRV-BITS:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the BITS configuration command Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[LINECDE=<LINECDE>,][FMT=<FMT>,][LBO=<LBO>,][SYNCMSG=<SYNCMSG>,] [AISTHRSHLD=<AISTHRSHLD>,][SABIT=<SABIT>,][IMPEDANCE=<IMPEDANCE>]: [<PST>]" ;
RTRV-COND-BITS:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the standing condition on BITS Output format:
SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;
RTRV-COND-SYNCN:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the synchronization condition Output format:
SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>], [<OCRDAT>],[<OCRTM>],,,[<DESC>]" ;
RTRV-NE-SYNCN:[<TID>]::<CTAG>[::::]; Retrieves the synchronization attributes of the NE Output format:
SID DATE TIME M CTAG COMPLD "::[TMMD=<TMMD>,][SSMGEN=<SSMGEN>,][QRES=<QRES>,][RVRTV=<RVRTV>,] [RVTM=<RVTM>]" ;
RTRV-SYNCN:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<REF>,<REFVAL>,[<PROTECTSTATUS>],[<QREF>],[<STATUS>]" ;
18 System
Table 19 System
ALW-MSG-ALL:[<TID>]::<CTAG>[::,,]; Allows REPT ALM and REPT EVT autonomous messages to be transmitted
ED-DAT:[<TID>]::<CTAG>::[<DATE>],[<TIME>]; Edits the date and the time
ED-NE-GEN:[<TID>]::<CTAG>:::[NAME=<NAME>,][IPADDR=<IPADDR>,] [IPMASK=<IPMASK>,][DEFRTR=<DEFRTR>,][IIOPPORT=<IIOPPORT>,][NTP=<NTP>] [ETHIPADDR=<ETHIPADDR>,][ETHIPMASK=<ETHIPMASK>]; Edits the general node attributes of an NE
INH-MSG-ALL:[<TID>]::<CTAG>[::,,]; Inhibits REPT ALM and REPT EVT autonomous messages from being transmitted
INIT-SYS:[<TID>]:<AID>:<CTAG>[::]; Initializes the specified card and its associated subsystem(s)
RTRV-HDR:[<TID>]::<CTAG>; Retrieves the header of a TL1 response message
RTRV-INV:[<TID>]:<AID>:<CTAG>[::::]; Retrieves a listing of the equipment inventory Output format:
SID DATE TIME M CTAG COMPLD "<AID>,<AIDTYPE>::[PLUGTYPE=<PLUGTYPE>,][PN=<PN>,][HWREV=<HWREV>,] [FWREV=<FWREV>,][SN=<SN>,][CLEI=<CLEI>,][TWL1=<TWL>,][TWL2=<TWL1>,] [TWL3=<TWL2>,][TWL4=<TWL3>,][PLUGINVENDORID=<PLUGINVENDORID>,] [PLUGINPN=<PLUGINPN>,][PLUGINHWREV=<PLUGINHWREV>,] [PLUGINFWREV=<PLUGINFWREV>,][PLUGINSN=<PLUGINSN>,] [ILOSSREF=<ILOSSREF>,][PID=<PID>,][VID=<VID>,][FPGA=<FPGA>]" ;
RTRV-NE-GEN:[<TID>]::<CTAG>; Retrieves the general NE attributes Output format:
SID DATE TIME M CTAG COMPLD "[IPADDR=<IPADDR>,][IPMASK=<IPMASK>,][DEFRTR=<DEFRTR>,] [IIOPPORT=<IIOPPORT>,][NTP=<NTP>,][ETHIPADDR=<ETHIPADDR>,] [ETHIPMASK=<ETHIPMASK>,][NAME=<NAME>,][SWVER=<SWVER>,][LOAD=<LOAD>,] [PROTSWVER=<PROTSWVER>,][PROTLOAD=<PROTLOAD>,][DEFDESC=<DEFDESC>,] [PLATFORM=<PLATFORM>]" ;
RTRV-NE-PATH:[<TID>]::<CTAG>[::::]; Retrieves the general NE attributes Output format:
SID DATE TIME M CTAG COMPLD "[PDIP=<PDIP>]" ;
RTRV-TOD:[<TID>]::<CTAG>; Retrieves the system date and time at the instant the command is executed Output format:
SID DATE TIME M CTAG COMPLD "<YEAR>,<MONTH>,<DAY>,<HOUR>,<MINUTE>,<SECOND>,<TMTYPE>" ;
SET-TOD:[<TID>]::<CTAG>::<YEAR>,<MONTH>,<DAY>,<HOUR>,<MINUTE>, <SECOND>,[<DIFFERENCE>][:DST=<DST>]; Sets the system date and time for the NE
19 Test Access
Table 20 Test Access
CHG-ACCMD-<MOD_TACC>:[<TID>]:<TAP>:<CTAG>::<MD>; Changes the test access mode for the circuit being tested
CONN-TACC-<MOD_TACC>:[<TID>]:<SRC>:<CTAG>::<TAP>:MD=<MD>; Connects the STS or VT defined by AID to the STS specified by the TAP number Output format:
SID DATE TIME M CTAG COMPLD "<TAP>" ;
DISC-TACC:[<TID>]:<TAP>:<CTAG>; Disconnects the TAP and puts the connection back to its original state
RTRV-TACC:[<TID>]:<TAP>:<CTAG>; Retrieves details associated with a TAP Output format:
SID DATE TIME M CTAG COMPLD "<TAP>:<TACC_AIDA>,<TACC_AIDB>,[<MD>],[<CROSSCONNECTID1>], [<CROSSCONNECTID2>]" ;
20 Testing
Table 21 Testing
OPR-LPBK-<MOD2>:[<TID>]:<AID>:<CTAG>::[<LOCATION>],,,[<LPBKTYPE>]; Operates a signal loopback on an I/O card or on a cross-connect
RLS-LPBK-<MOD2>:[<TID>]:<SRC>:<CTAG>::[<LOCATION>],,,[<LPBKTYPE>]; Releases a signal loopback on an I/O card or on a cross-connect
21 Trace
Table 22 Trace
RTRV-PTHTRC-<STS_PATH>:[<TID>]:<SRC>:<CTAG>::[<MSGTYPE>][:<LOCN>]; Retrieves the contents of the SONET path trace message that is transported in the J1 byte of the SONET STS path Output format:
SID DATE TIME M CTAG COMPLD "<TRACMSG>" ;
22 UCP (Cisco ONS 15454 only)
Table 23 UCP
DLT-UCP-CC:[<TID>]:<AID>:<CTAG>[::::]; Deletes a UCP IP control channel
DLT-UCP-IF:[<TID>]:<AID>:<CTAG>[::::]; Deletes a UCP interface
DLT-UCP-NBR:[<TID>]:<AID>:<CTAG>[::::]; Deletes a UCP neighbor
ED-UCP-CC:[<TID>]:<AID>:<CTAG>:::[LOCALIPCC=<LOCALIPCC>,] [REMOTEIPCC=<REMOTEIPCC>,][LMPHELLOINT=<LMPHELLOINT>,] [LMPHELLODEADINT=<LMPHELLODEADINT>,][MTU=<MTU>,] [CRCMD=<CRCMD>][:]; Edits UCP IP control channel attributes
ENT-UCP-CC:[<TID>]:[<AID>]:<CTAG>:::NBRIX=<NBRIX>,CCTYPE=<CCTYPE>, [PORT=<PORT>,][LOCALCCID=<LOCALCCID>,][LOCALIPCC=<LOCALIPCC>,] [REMOTCCID=<REMOTECCID>,][REMOTEIPCC=<REMOTEIPCC>,] [LMPHELLOINT=<LMPHELLOINT>,][LMPHELLODEADINT=<LMPHELLODEADINT>,] [MTU=<MTU>,][CRCMD=<CRCMD>,][TUNMD=<TUNMD>][:]; Creates a UCP IP control channel
ENT-UCP-IF:[<TID>]:<AID>:<CTAG>:::[NBRIX=<NBRIX>,][CCID=<CCID>,] [LOCALIFID=<LOCALIFID>,][REMOTEIFID=<REMOTEIFID>,][TNATYPE=<TNATYPE>,] [TNAADDR=<TNAADDR>,][CORENETWORKID=<CORENETWORKID>][:]; Creates a UCP interface
ENT-UCP-NBR:[<TID>]:<AID>:<CTAG>:::[NBRIX=<NBRIX>,][NODEID=<NODEID>,] NAME=<NAME>,[NDEN=<NDEN>,][HELLOEN=<HELLOEN>,][HELLOINT=<HELLOINT>,] [REFREDEN=<REFREDEN>,][NUMRXMTS=<NUMRXMTS>][:]; Creates a UCP neighbor
REPT ALM UCP Reports an alarm condition against a UCP object
REPT EVT UCP Reports the occurrence of a non-alarmed event against a UCP object
RTRV-ALM-UCP:[<TID>]:<AID >:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>][,,,]; Retrieves and sends the current status of all active alarm conditions against a UCP object Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,,,,:[<DESC>]" ;
RTRV-COND-UCP:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the current standing condition against a UCP object Output format:
SID DATE TIME M CTAG COMPLD "<AID>:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;
RTRV-UCP-CC:[<TID>]:[<AID >]:<CTAG>[::::]; Retrieves UCP IP control channel attributes Output format:
SID DATE TIME M CTAG COMPLD "[<AID>]::NBRIX=<NBRIX>,CCTYPE=<CCTYPE>,[PORT=<PORT>,] LOCALCCID=<LOCALCCID>,LOCALIPCC=<LOCALIPCC>, REMOTECCID=<REMOTECCID>,[REMOTEIPCC=<REMOTEIPCC>,] LMPHELLOINT=<LMPHELLOINT>,OPERLMPHELLOINT=<OPERLMPHELLOINT>, LMPHELLODEADINT=<LMPHELLODEADINT>, OPERLMPHELLODEADINT=<OPERLMPHELLODEADINT>, [TUNMD=<TUNMD>,][MTU=<MTU>,][CRCMD=<CRCMD>]" ;
SID DATE TIME M CTAG COMPLD "[<AID>]::NBRIX=<NBRIX>,CCID=<CCID>,LOCALIFID=<LOCALIFID>, REMOTEIFID=<REMOTEIFID>,TNATYPE=<TNATYPE>, TNAADDR=<TNAADDR>,CORENETWORKID=<CORENETWORKID>" ;
RTRV-UCP-NBR:[<TID>]:[<AID>]:<CTAG>[::::]; Retrieves a UCP neighbor Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[NBRIX=<NBRIX>,][NODEID=<NODEID>,][NAME=<NAME>,] [NDEN=<NDEN>,][HELLOEN=<HELLOEN>,][HELLOINT=<HELLOINT>,] [REFREDEN=<REFREDEN>,][NUMRXMTS=<NUMRXMTS>]" ;
SID DATE TIME M CTAG COMPLD "::[NODEID=<NODEID>,][INITRETRY=<INITRETRY>,][MAXRETRY=<MAXRETRY>,] [RESTARTTM=<RESTARTTM>,][RECOVTM=<RECOVTM>,][RXMTINT=<RXMTINT>,] [RFRSHINT=<RFRSHINT>,][RESVTIMEOUT=<RESVTIMEOUT>,] [RESVCONFTIMEOUT=<RESVCONFTIMEOUT>,] [SOURCEDIP=<SOURCEDIP>,][DESTINATIONDIP=<DESTINATIONDIP>]" ;
23 Path Protection Switching
Table 24 Path Protection Switching
REPT SW Reports the autonomous switching of a unit in a duplex equipment pair to standby and its mate to the active state
24 VCAT
Table 25 VCAT
DLT-VCG:[<TID>]:<SRC>:<CTAG>:::[CMDMDE=<CMDMDE>][:]; Deletes a virtual concatenated group (VCG) object
ENT-VCG:[<TID>]:<SRC>:<CTAG>:::TYPE=<TYPE>,TXCOUNT=<TXCOUNT>,[CCT=<CCT>, [LCAS=<LCAS>][:]; Creates a VCG object
RTRV-VCG:[<TID>]:<SRC>:<CTAG>[::::]; Retrieves all of the attributes provisioned for a VCG Output format:
SID DATE TIME M CTAG COMPLD "<SRC>::TYPE=<TYPE>,TXCOUNT=<TXCOUNT>,CCT=<CCT>,LCAS=<LCAS>" ;
[an error occurred while processing this directive]