-
Network Analysis Module Command Reference Guide, 4.0
-
Index
-
NAM CLI Commands: alarm event - ip http secure port
-
NAM CLI Commands: ip http secure port - monitor nbar
-
NAM CLI Commands: monitor matrix - preferences
-
NAM CLI Commands: esp-null-heuristic - show hosts
-
NAM CLI Commands: show inventory - show rmon buffer
-
NAM CLI Commands: show rmon channels - web-user
-
Table Of Contents
NAM CLI Commands:
monitor matrix - preferencesmonitor protocol auto-learned max-entry
monitor protocol auto-learned tcp exclude
monitor protocol auto-learned tcp max-port
monitor protocol auto-learned udp exclude
monitor protocol auto-learned udp max-port
monitor protocol auto-learned udp max-port
monitor protocol encapsulation
monitor rtp-stream pkt-loss-alarm
NAM CLI Commands:
monitor matrix - preferences
This chapter describes the following NAM CLI Commands:
•
monitor protocol auto-learned
•
•
•
•
•
•
•
•
monitor matrix
To enter the matrix collection configuration subcommand mode, and then configure matrix collections, use the monitor matrix command. To remove the host collections, use the no form of this command.
monitor matrix
no monitor matrix control-index
Syntax Description
Defaults
The control index is random.
Command Modes
Command mode
Usage Guidelines
When you enter the monitor matrix collection subcommand mode, the following commands are available:
•
•
•
•
•
Note
Examples
This example shows how to configure monitor matrix collections:
root@localhost.cisco.com# monitor matrixEntering into sub-command mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@localhost.cisco.com(sub-monitor-matrix)# data-source allspanroot@localhost.cisco.com(sub-monitor-matrix)# owner testroot@localhost.cisco.com(sub-monitor-matrix)# control-index 5root@localhost.cisco.com(sub-monitor-matrix)# exitSuccessfully created a matrix collection.root@localhost.cisco.com# show monitor matrix 5Control index: 5Data source: allspanOwner: testStatus: 1root@localhost.cisco.com# no monitor matrix 5Successfully removed the matrix collection.Related Commands
monitor nbar
To enable supervisor NBAR statistics polling, use the monitor nbar command. To disable polling, use the no form of this command.
monitor nbar
no monitor nbar
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no defaults.
Command Modes
Command mode
Usage Guidelines
The NBAR-PD-MIB must be present to enable the collection of statistical information.
The device using the command determines where statistics are polled from as follows:
•
•
Examples
This example shows how to enable NBAR statistics polling:
root@localhost.cisco.com# monitor nbarSuccessful enable nbar collection.root@localhost.cisco.com# no monitor nbarSuccessfully disable nbar collection.This example shows how to display NBAR statistics polling:
root@localhost.cisco.com# show monitor nbarnbar collection enabledRelated Commands
monitor pdist
To enter the protocol distribution collection configuration subcommand mode, and then configure protocol distribution collections, use the monitor pdist command. To remove the protocol distribution collections, use the no form of this command.
monitor pdist
no monitor pdist control-index
Syntax Description
Defaults
The control index is random.
Command Modes
Command mode
Usage Guidelines
When you enter the monitor protocol distribution collection subcommand mode, the following commands are available:
•
•
•
•
•
Note
Examples
This example shows how to configure monitor protocol distribution collections:
root@localhost.cisco.com# monitor pdistEntering into sub-command mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@localhost.cisco.com(sub-monitor-pdist)# data-source vlan1root@localhost.cisco.com(sub-monitor-pdist)# exitSuccessfully created a pdist collection.root@localhost.cisco.com# show monitor pdistControl index: 44272Data source: vlan1Owner: monitorStatus: 1root@localhost.cisco.com# no monitor pdist 44272Successfully removed the pdist collection.Related Commands
monitor priostats
To enter the priority statistics collection configuration subcommand mode, and then configure priority statistics collections, use the monitor priostats command. To remove the priority statistics collections, use the no form of this command.
monitor priostats
no monitor priostats control-index
Syntax Description
Defaults
The control index is random.
Command Modes
Command mode
Usage Guidelines
When you enter the monitor priority statistics collection subcommand mode, the following commands are available:
•
•
•
•
•
Examples
This example shows how to configure priority statistics collections:
root@localhost.cisco.com# monitor priostatsEntering into sub-command mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@localhost.cisco.com(sub-monitor-priostats)# data-source vlan1002root@localhost.cisco.com(sub-monitor-priostats)# exitSuccessfully created a prio stats collection.Related Commands
monitor protocol
To enter the protocol directory entries configuration subcommand mode, and then configure protocol directory entries, use the monitor protocol command. To remove the protocol directory entries, use the no form of this command.
monitor protocol
no monitor protocol prot-specifier
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
When you enter the monitor protocol directory entries subcommand mode, the following commands are available:
•
•
•
•
•
•
•
Note
•
•
Examples
This example shows how to configure protocol directory entries:
root@localhost.cisco.com# monitor protocolEntering into sub-command mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@localhost.cisco.com(sub-monitor-protocol)# prot-specifier 12.1.0.0.1.0.0.8.0.0.0.0.17.3.0 .1.0root@localhost.cisco.com(sub-monitor-protocol)# host disableroot@localhost.cisco.com(sub-monitor-protocol)# conversations disableroot@localhost.cisco.com(sub-monitor-protocol)# exitSuccessfully updated the protocol directory entry.root@localhost.cisco.com# show monitor protocol 12.1.0.0.1.0.0.8.0.0.0.0.17.3 .0.1.0w-ether2.ip.udpProtocol specifier:12.1.0.0.1.0.0.8.0.0.0.0.17.3.0.1.0Address map stats: N/AHost stats: DisabledConversation stats:DisabledART stats: N/Aroot@localhost.cisco.com# no monitor protocol 12.1.0.0.1.0.0.8.0.0.0.0.17.3.0 .1.0Successfully removed the protocol directory entry.root@localhost.cisco.com# monitor protocolEntering into sub-command mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@localhost.cisco.com(sub-monitor-protocol)# prot-specifier 12.1.0.0.1.0.0.8.0.0.0.0.17.3.0 .1.0root@localhost.cisco.com(sub-monitor-protocol)# host enableroot@localhost.cisco.com(sub-monitor-protocol)# addressmap not-applicableroot@localhost.cisco.com(sub-monitor-protocol)# conversations enableroot@localhost.cisco.com(sub-monitor-protocol)# art disableroot@localhost.cisco.com(sub-monitor-protocol)# exitSuccessfully created a protocol directory entry.root@localhost.cisco.com# show monitor protocolProtocol specifier:12.1.0.0.1.0.0.8.0.0.0.0.17.3.0.1.0Address map stats: N/AHost stats: EnabledConversation stats:EnabledART stats: DisabledRelated Commands
monitor protocol auto-learned
To enable the automatically learned protocols, use the monitor protocol auto-learned command. To disable automatically learned protocols, use the no form of this command.
monitor protocol auto-learned
no monitor protocol auto-learned
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Examples
This example shows how to set protocol automatic learning:
root@localhost.cisco.com# monitor protocol auto-learnedRelated Commands
show monitor protocol auto-learned settings
monitor protocol auto-learned max-entry
To set the maximum number of automatically learned protocol entries, use the monitor protocol auto-learned max-entry command. To reset the maximum number of automatically learned protocol entries to the default value, use the no form of this command.
monitor protocol auto-learned max-entry entries
no monitor protocol auto-learned max-entry
Syntax Description
Defaults
100 entries.
Command Modes
Command mode
Examples
This example shows how to set protocol automatic learning:
root@localhost.cisco.com# monitor protocol auto-learned max-entry 20Related Commands
show monitor protocol auto-learned settings
monitor protocol auto-learned tcp exclude
To set the automatically learned protocol feature's TCP port exclusion, use the monitor protocol auto-learned tcp exclude command. To remove the automatically learned protocol feature's TCP port exclusion, use the no form of this command.
monitor protocol auto-learned tcp exclude begin-port | end-port
no monitor protocol auto-learned tcp exclude
Syntax Description
begin-port
Specifies the beginning port for the port exclusion.
end-port
Specifies the ending port for the port exclusion.
Defaults
No TCP port is excluded.
Command Modes
Command mode
Examples
This example shows how to set protocol automatic learning:
root@localhost.cisco.com# monitor protocol auto-learned tcp exclude 20 50Related Commands
show monitor protocol auto-learned settings
monitor protocol auto-learned tcp max-port
To set the maximum number of TCP port values that the automatically learned protocol feature can learn up to, use the monitor protocol auto-learned tcp max-port command. To reset the maximum TCP port value for automatically learned protocols to the default value, use the no form of this command.
monitor protocol auto-learned tcp max-port max-port
no monitor protocol auto-learned max-port
Syntax Description
max-port
Sets the maximum number of ports that the automatically learned protocol feature can learn up to. Ports above this setting are not learned. Range is from 1 to 65535.
Defaults
The maximum number of learned ports is 65535.
Command Modes
Command mode
Usage Guidelines
If you apply the monitor protocol auto-learned tcp max-port 100 command to the NAM, the NAM does not learn protocols that have TCP port values of 101 or more.
Examples
This example shows how to set protocol automatic learning:
root@localhost.cisco.com# monitor protocol auto-learned tcproot@localhost.cisco.com# monitor protocol auto-learnedRelated Commands
show monitor protocol auto-learned settings
monitor protocol auto-learned udp exclude
To set the automatically learned protocol feature's UDP port exclusion, use the monitor protocol auto-learned udp exclude command. To remove the automatically learned protocol feature's UDP port exclusion, use the no form of this command.
monitor protocol auto-learned udp exclude begin-port | end-port
no monitor protocol auto-learned udp exclude
Syntax Description
begin-port
Specifies the beginning port for the port exclusion.
end-port
Specifies the ending port for the port exclusion.
Defaults
No UDP port is excluded.
Command Modes
Command mode
Examples
This example shows how to set protocol automatic learning:
root@localhost.cisco.com# monitor protocol auto-learned udp exclude 20 50Related Commands
show monitor protocol auto-learned settings
monitor protocol auto-learned udp max-port
To set the maximum number of UDP port values that the automatically learned protocol feature can learn up to, use the monitor protocol auto-learned udp max-port command. To reset the maximum UDP port values for automatically learned protocols to the default value, use the no form of this command.
monitor protocol auto-learned udp max-port max-port
no monitor protocol auto-learned max-port
Syntax Description
max-port
Sets the maximum number of ports that the automatically learned protocol feature can learn up to. Ports above this setting are not learned. Range is from 1 to 65535.
Defaults
The maximum number of learned ports is 65535.
Command Modes
Command mode
Usage Guidelines
If you apply the monitor protocol auto-learned udp max-port 100 command to the NAM, the NAM does not learn protocols that have UDP port values of 101 or more.
Examples
This example shows how to set protocol automatic learning:
root@localhost.cisco.com# monitor protocol auto-learned udpRelated Commands
show monitor protocol auto-learned settings
monitor protocol auto-learned udp max-port
To set the maximum number of UDP port values that the automatically learned protocol feature can learn up to, use the monitor protocol auto-learned udp max-port command. To reset the maximum UDP port values for automatically learned protocols to the default value, use the no form of this command.
monitor protocol encapsulation
To be supplied.
monitor protocol encapsulation
no monitor protocol encapsulation
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Examples
This example shows how to
Related Commands
monitor rtp-stream filter
To set a RTP stream filtering entry, use the monitor rtp-stream filter command. To remove a RTP stream filtering entry, use the no form of the is command..
monitor rtp-stream filter source-address source-mask dest-address dest-mask
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Examples
This example shows how to enable RTP stream filtering:
root@localhost# monitor rtp-stream filter 1.2.3.0 255.255.255.0 4.5.0.0 255.255.0.0Related Commands
monitor protocol encapsulation
monitor rtp-stream max-entry
monitor rtp-stream pkt-loss-alarmmonitor rtp-stream max-entry
To set the number RTP streams for monitoring, use the monitor rtp-stream max-entry command. To set the max number of RTP streams for monitoring to manufracturing default value (30), use the no form of this command.
monitor rtp-stream max-entry [max-entries]
no monitor rtp-stream max-entry
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Examples
This example shows how to enable RTP stream monitoring:
root@localhost.cisco.com# monitor rtp-stream max-entry 50Related Commands
monitor protocol encapsulation
monitor rtp-stream filter
monitor rtp-stream pkt-loss-alarm
monitor rtp-stream pkt-loss-alarm
To enable alarm for RTP stream packet loss, use the monitor rtp-stream pkt-loss-alarm command. To disable alarm on RTP stream packet loss, use the no form of this command.
monitor rtp-stream pkt-loss-alarm enable threshold
no monitor rtp-stream pkt-loss-alarm
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Examples
This example shows how to enable an alarm for RTP stream monitoring of lost packets:
root@localhost.cisco.com# monitor rtp-stream pkt-loss-alarm 23 44Related Commands
monitor protocol encapsulation
monitor rtp-stream max-entry
monitor urlcollection
To enter the URL collection submode and configure URL collections, use the monitor urlcollection command. To disable the URL collection, use the no form of this command.
monitor urlcollection
no monitor urlcollection
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
When you enter the URL collections submode, the following commands are available:
•
•
•
•
•
–
–
–
–
•
•
•
There is only one URL collection in the NAM. The collection owner is always LocalMgr. The index is always one.
This command is supported by the NAM-1, NAM-2, and NM-NAM.
Examples
This example shows how to configure URL collections:
root@localhost# monitor urlcollectionsroot@localhost#Related Commands
clear access log
show monitor urlcollectionmonitor urlfilter
To enter the URL filter collection configuration subcommand mode, and then configure URL filters, use the monitor urlfilter command. To remove the URL filters from the configuration, use the no form of this command.
monitor urlfilter
no monitor urlfilter control-index
Syntax Description
Defaults
The control index is random.
Command Modes
Command mode
Usage Guidelines
When you enter the monitor URL filter subcommand mode, the following commands are available:
•
•
•
•
•
•
•
•
•
The clear configuration command removes the URL filters from the configuration. There is no SNMP support for configuring the URL filters.
Examples
This example shows how to configure URL filters:
root@nam# monitor urlfilterEntering into subcommand mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@nam(sub-monitor-url-filter)# control-index 2root@nam(sub-monitor-url-filter)# description urlfilter exampleroot@nam(sub-monitor-url-filter)# host-regexp www.example.comroot@nam(sub-monitor-url-filter)# protocol-encap ipv4root@nam(sub-monitor-url-filter)# exitSucessfully created urlfilter entry.root@nam# show monitor urlfilterDescription: urlfilter exampleControl index: 2Protocol encapsulation: IPv4URL's host string: www.example.comURL's path string: (not-set)To remove this URL filter entry, use the no form of the command:
root@nam# no monitor urlfilter 2Successfully delete urlfilter entry.Related Commands
clear access log
show monitor urlfiltermonitor vlanstats
To enter the VLAN statistics collection configuration subcommand mode, and then configure VLAN statistics collections, use the monitor vlanstats command. To remove the VLAN statistics collections, use the no form of this command.
monitor vlanstats
no monitor vlanstats control-index
Note
Syntax Description
This command has no arguments or keywords.
Defaults
The control index is random.
Command Modes
Command mode
Usage Guidelines
When you enter the monitor VLAN statistics collection subcommand mode, the following commands are available:
•
•
•
•
•
Note
Examples
This example shows how to configure VLAN statistics collections:
root@localhost.cisco.com# monitor vlanstatsEntering into sub-command mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@localhost.cisco.com(sub-monitor-vlanstats)#root@localhost.cisco.com(sub-monitor-vlanstats)# data-source vlan1002root@localhost.cisco.com(sub-monitor-vlanstats)# exitSuccessfully created a vlan stats collection.root@localhost.cisco.com# show monitor vlanstatsControl index: 35955Data source: vlan1002Owner is monitorStatus: 1root@localhost.cisco.com# no monitor vlanstats 35955Successfully removed the vlan stats collection.Related Commands
monitor vlanstats on-switch
To configure supervisor engine VLAN statistics collections, use the monitor vlanstats on-switch command. To disable the VLAN statistics collections, use the no form of this command.
monitor vlanstats on-swtich
no monitor vlanstats on-switch
Syntax Description
This command has no arguments or keywords.
Defaults
This command has not default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported only on the NAM-1 and NAM-2 only.
Examples
This example shows how to configure supervisor engine VLAN statistics collections:
root@localhost.cisco.com# monitor vlanstats on-switchSuccessfully enable supervisor vlanstats on-switch.This example shows how to display supervisor engine VLAN statistics collections:
root@localhost.cisco.com# show monitor vlanstats on-switchSupervisor vlanstats collection is enabled.This example shows how to disable supervisor engine VLAN statistics collections:
root@localhost.cisco.com# no monitor vlanstats on-switchSuccessfully disable supervisor vlanstats on-switch.Related Commands
show monitor vlanstats on-switch
monitor voice h.323
To enter the H.323 voice collection configuration subcommand mode, and then configure H.323 voice collections, use the monitor voice h.323 command. To disable the H.323 voice collections, use disable in the monitor voice h.323 subcommand mode.
monitor voice h.323
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
When you enter the monitor voice H.323 statistics collection subcommand mode, the following commands are available:
•
•
•
•
•
•
•
•
Examples
This example shows how to configure H.323 voice collections:
root@localhost.cisco.com# monitor voice h.323Entering into sub-command mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@localhost.cisco.com(sub-monitor-voice-h.323)# disableroot@localhost.cisco.com(sub-monitor-voice-h.323)# exitSuccessfully disabled the h.323 voice collection with changes.root@localhost.cisco.com# show monitor voice h.323H.323 voice monitoring: DisabledNumber of phone table rows: 200Number of call table rows: 1000Number of top packet jitter rows: 5Number of top packet loss rows: 5Related Commands
monitor voice h.323
show monitor vlanstatsmonitor voice mgcp
To enter the Media Gateway Control Protocol (MGCP) collection configuration subcommand mode, and then configure MGCP collections, use the monitor voice mgcp command. To disable MGCP collections, use disable in the monitor voice mgcp subcommand mode.
monitor voice mgcp
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
When you enter the monitor voice MGCP statistics collection subcommand mode, the following commands are available:
•
•
•
•
•
•
•
•
Examples
This example shows how to configure MGCP collections:
root@localhost.cisco.com# monitor voice mgcpEntering into sub-command mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@localhost.cisco.com(sub-monitor-voice-mgcp)# disableroot@localhost.cisco.com(sub-monitor-voice-mgcp)# exitSuccessfully disabled the MGCP collection with changes.Root@localhost# show monitor voice mgcpMGCP voice monitoring: DisabledNumber of phone table rows: 150Number of call table rows: 150Number of top packet jitter rows: 7Number of top packet loss rows: 7Related Commands
monitor voice h.323
show monitor vlanstatsmonitor voice sccp
To enter the Skinny Client Control Protocol (SCCP) voice statistics collection configuration subcommand mode, and then configure SCCP voice collection, use the monitor voice sccp command. To disable SCCP voice collection, use disable in the monitor voice sccp subcommand mode.
monitor voice sccp
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
When you enter the monitor voice SCCP statistics collection subcommand mode, the following commands are available:
•
•
•
•
•
•
•
•
Examples
This example shows how to configure voice SCCP statistics collections:
root@localhost.cisco.com# monitor voice sccpEntering into sub-command mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@localhost.cisco.com(sub-monitor-voice-sccp)# top-loss-rows 500ERROR:You have specified a number of loss rows which is not valid.The number of loss rows must be between 1 and 20.root@localhost.cisco.com(sub-monitor-voice-sccp)# top-loss-rows 20root@localhost.cisco.com(sub-monitor-voice-sccp)# top-jitter-rows 20root@localhost.cisco.com(sub-monitor-voice-sccp)# exitSuccessfully enabled the sccp voice collection with changes.root@localhost.cisco.com# show monitor voice sccpSCCP voice monitoring: EnabledNumber of phone table rows: 300Number of call table rows: 100Number of top packet jitter rows: 20Number of top packet loss rows: 20Related Commands
monitor voice h.323
show monitor vlanstatsmonitor voice sip
To enter the Session Initiation Protocol (SIP) voice statistics collection configuration subcommand mode, and then configure SIP voice collection, use the monitor sip command. To disable SIP voice collection, use disable in the monitor sip subcommand mode.
monitor voice sip
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
When you enter the monitor voice SIP statistics collection subcommand mode, the following commands are available:
•
•
•
•
•
•
•
•
•
Examples
This example shows how to configure SIP collections:
root@namlab-kom6.cisco.com# monitor voice sipEntering into subcommand mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@namlab-kom6.cisco.com(sub-monitor-voice-sip)# enableroot@namlab-kom6.cisco.com(sub-monitor-voice-sip)# max-calls 250root@namlab-kom6.cisco.com(sub-monitor-voice-sip)# max-phones 500root@namlab-kom6.cisco.com(sub-monitor-voice-sip)# top-jitter-rows 20root@namlab-kom6.cisco.com(sub-monitor-voice-sip)# top-loss-rows 20root@namlab-kom6.cisco.com(sub-monitor-voice-sip)# exitSuccessfully enabled the sip voice collection with changes.root@namlab-kom6.cisco.com# show monitor voice sipSIP voice monitoring: EnabledNumber of phone table rows: 500Number of call table rows: 250Number of top packet jitter rows: 20Number of top packet loss rows: 20root@namlab-kom6.cisco.com#Related Commands
mpls data-source label
To create a NAM MPLS data source specifically interested in a local MPLS label, use this command. (optionally provide a user-meaningful data source name. , use the mpls data-source label command. To remove the MPLS data source, use the no form of this command.
mpls data-source label data-source-value
no mpls data-source label data-source-value
Syntax Description
Defaults
LABEL:label in the data source name.
Command Modes
Command mode
Usage Guidelines
Examples
This example shows how to parse set up an MPLS data source on the NAM collect RMON statistics:
root@localhost# mpls data-source label XXXYYY12345root@localhost#Related Commands
mpls data-source vc
mpls data-source vrf
show nam data-sourcempls data-source vc
To create a NAM MPLS data source based on an MPLS virtual circuit ID, use the mpls data-source vc command. To remove the MPLS data source, use the no form of this command.
mpls data-source vc vc-id
no mpls data-source vc-id
Syntax Description
vc
Specifies an MPLS data source based on a virtual circuit ID.
vc-id
Specifies the virtual circuit ID. Range is from 1 to 65535.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
Examples
This example shows how to parse set up an MPLS data source on the NAM collect RMON statistics:
root@localhost# mpls data-source vc 12345root@localhost#Related Commands
mpls data-source vrf
mpls data-source label
show nam data-sourcempls data-source vrf
To create a NAM MPLS data source based on and MPLS VRF name string, use the mpls data-source vrf command. To remove the MPLS data source, use the no form of this command.
mpls data-source vrf vrf-name-string
no mpls data-source vrf-name-string
Syntax Description
vrf
Specifies an MPLS data source based on a virtual rf ID.
vrf-name-string
Specifies the virtual rf ID.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
Examples
This example shows how to parse set up an MPLS data source on the NAM collect RMON statistics:
root@localhost# mpls data-source vrf netflowroot@localhost#Related Commands
mpls data-source vc
mpls data-source label
show nam data-sourcenetflow data-source
To enter the NetFlow data source configuration subcommand mode, and then create or edit a custom data source, use the netflow data-source command. To remove a NetFlow custom data source, use the no form of this command.
netflow data-source
no netflow data-source data-source-name
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
When you enter the NetFlow data source configuration subcommand mode, the following commands are available:
•
•
•
•
•
•
•
•
To create a new NetFlow custom data source, you must not provide an index value in the subcommand mode. If an index value is provided, it is an edit of an existing NetFlow custom data source.
The NetFlow custom data source name is prepended with nde-. For example, nde-exampleNetFlow.
You must give NetFlow device information.
All the if-indices values are provided by the NetFlow device. You do not need to provide all three directions (input, output, and both) but there must be at least one of the three.
Examples
This example shows how to configure a remote NetFlow device:
root@localhost# netflow device 10.0.0.2Successfully created a NetFlow device.root@localhost#root@localhost# netflow data-sourceEntering into subcommand mode for this command.Type `exit' to come out of this mode.Type `cancel' to discard changes and to come out of this mode.root@localhost(sub-netflow-data-source)# device 10.0.0.2root@localhost(sub-netflow-data-source)# name exampleNetFlowroot@localhost(sub-netflow-data-source)# input 1 2root@localhost(sub-netflow-data-source)# output 3 4 5root@locaroot(sub-netflow-data-source)# both 22 29root@locaroot(sub-netflow-data-source)# exitRelated Commands
netflow device
To configure remote NetFlow devices and create a default data source for the NetFlow device, use the netflow device command. To remove a remote NetFlow device, use the no form of this command.
netflow device device-address [community-string]
no netflow device address
Syntax Description
device-address
Specifies the remote NetFlow device address.
community-string
(Optional) Specifies the remote NetFlow device community string.
Defaults
This command has no default settings.
Command Modes
Command mode
Examples
This example shows how to configure a remote NetFlow device:
root@localhost# netflow device 10.0.0.1 publicSuccessfully created a netflow device.root@localhost# show nam data-sourceallspannde-10.0.0.1root@localhost# no netflow device 10.0.0.1Successfully removed the netflow device.nslookup
To configure name server queries, use the nslookup command.
nslookup hostname [server]
Syntax Description
hostname
Specifies the name server query host.
server
(Optional) Specifies the name server to query.
Defaults
This command has no default settings.
Command Modes
Command mode
Examples
This example shows how to configure name server queries:
root@localhost.cisco.com# nslookup www.yahoo.comServer: 127.0.0.1Address: 127.0.0.1#53Non-authoritative answer:www.yahoo.com canonical name = www.yahoo.akadns.net.Name: www.yahoo.akadns.netAddress:66.218.71.80password
To set a new password, use the password command.
password username
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
There are only two valid users, root and guest.
Examples
This example shows how to set a password:
root@localhost.cisco.com# password rootChanging password for user rootNew UNIX password:Retype new UNIX password:passwd:all authentication tokens updated successfullyroot@localhost.cisco.com#patch
To download and install a software patch, use the patch command.
patch ftp://user:passwd@host/full-path/filename
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Examples
This example shows how to download and install a patch:
root@localhost.cisco.com# patch ftp://hostname/fullpath/c6nam-3.6-strong-cryptoK9-patch-1-0.binProceeding with installation. Please do not interrupt.If installation is interrupted, please try again.Downloading c6nam-3.6-strong-cryptoK9-patch-1-0.bin. Please wait...ftp://hostname/fullpath/c6nam-3.6-strong-cryptoK9-patch-1-0.bin (1K)- [########################] 1K | 1886.33K/s1891 bytes transferred in 0.00 sec (1569.00k/sec)Verifying c6nam-3.6-strong-cryptoK9-patch-1-0.bin. Please wait...Patch c6nam-3.6-strong-cryptoK9-patch-1-0.bin verified.Applying /usr/local/nam/patch/workdir/c6nam-3.6-strong-cryptoK9-patch-1-0.bin. Please wait...########################################### [100%]########################################### [100%]Patch applied successfully.root@localhost.cisco.com#Related Commands
ping
To check connectivity to a network device, use the ping command.
ping [-n | -v] [-c count] [-i wait] [-p pattern] [-s packetsize] hostname | IP address
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Examples
This example shows how to check the connectivity of a network device with ping:
root@localhost# ping -n -v ralph 100.20.19.23root@localhost#preferences
To enter the preferences subcommand mode, and then configure how your screen displays information, use the preferences command.
preferences
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
When you enter the preferences subcommand mode, the following commands are available:
•
•
•
•
•
•
•
•
•
•
•
Examples
This example shows how to configure preferences for your screen display:
root@localhost.cisco.com# preferencesEntering into subcommand mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@localhost.cisco.com(sub-preferences)# entries-per-screen 15root@localhost.cisco.com(sub-preferences)# refresh-interval 60root@localhost.cisco.com(sub-preferences)# graph-bars 10root@localhost.cisco.com(sub-preferences)# hostname-resolution disableroot@localhost.cisco.com(sub-preferences)# data-displayed bytesroot@localhost.cisco.com(sub-preferences)# format-large-number enableroot@localhost.cisco.com(sub-preferences)# number-notation comma-dotroot@localhost.cisco.com(sub-preferences)# exitNAM web interface preferences updated successfully.dataThis example shows how to display the configured preferences:
root@localhost.cisco.com# show preferencesEntries per screen: 15Refresh interval: 60 secsNumber of graph bars: 10Hostname resolution: DisabledData displayed in: BytesFormat large number: NoNumber notation: Commas-dotroot@localhost.cisco.com#Related Commands
