This documentation has been moved
Multilink Frame Relay over L2TPv3/AToM
Download this chapter
Multilink Frame Relay over L2TPv3/AToMMultilink Frame Relay over L2TPv3/AToM
Download the complete book
MPLS Configuration Guide, Cisco IOS Release 15.1M&T MPLS Configuration Guide, Cisco IOS Release 15.1M&T (PDF - 8 MB)
 Feedback

Table Of Contents

Multilink Frame Relay over L2TPv3/AToM

Contents

Prerequisites for Configuring Multilink Frame Relay over L2TPv3/AToM

Restrictions for Configuring Multilink Frame Relay over L2TPv3/AToM

Information About Configuring Multilink Frame Relay over L2TPv3/AToM

Multilink Frame Relay over L2TPv3/AToM

Internetworking Support for Multilink Frame Relay

Quality of Service Support for Multilink Frame Relay over L2TPv3/AToM

How to Configure Multilink Frame Relay over L2TPv3/AToM

Configuring a Multilink Frame Relay Bundle Interface

Configuring a Multilink Frame Relay Bundle Link Interface

Connecting Frame Relay PVCs Between Routers

Verifying Multilink Frame Relay over L2TPv3/AToM

Configuration Examples for Multilink Frame Relay over L2TPv3/AToM

Frame Relay-to-Frame Relay over L2TPv3 on Multilink Frame Relay Interfaces: Example

Frame Relay-to-Ethernet VLAN Interworking over L2TPv3 on Multilink Frame Relay Interfaces: Example

Frame Relay-to-Ethernet Interworking over MPLS on Multilink Frame Relay Interfaces: Example

MQC Color-Aware Policing: Example

DE Bit Matching: Example

DLCI-Based queueing: Example

Discard Class-Based WRED: Example

Aggregate Shaping: Example

VC Shaping: Example

FECN/BECN Marking: Example

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Command Reference

Feature Information for Multilink Frame Relay over L2TPv3/AToM


Multilink Frame Relay over L2TPv3/AToM

First Published: May 6, 2004
Last Updated: November 17, 2006

This feature enables Multilink Frame Relay switching over Layer 2 Tunnel Protocol Version 3 (L2TPv3) and Any Transport over MPLS (AToM). The feature works with like-to-like interfaces and disparate interfaces (L2VPN interworking).

Multilink Frame Relay is the logical grouping of one or more physical interfaces between two devices of the User-to-Network Interface/Network-to-Network Interface (UNI/NNI) as one single Frame Relay data link.

Finding Feature Information in This Module

Your Cisco IOS software release may not support all of the features documented in this module. To reach links to specific feature documentation in this module and to see a list of the releases in which each feature is supported, use the "Feature Information for Multilink Frame Relay over L2TPv3/AToM" section.

Finding Support Information for Platforms and Cisco IOS and Catalyst OS Software Images

Use Cisco Feature Navigator to find information about platform support and Cisco IOS and Catalyst OS software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

•Prerequisites for Configuring Multilink Frame Relay over L2TPv3/AToM

•Restrictions for Configuring Multilink Frame Relay over L2TPv3/AToM

•Information About Configuring Multilink Frame Relay over L2TPv3/AToM

•How to Configure Multilink Frame Relay over L2TPv3/AToM

•Configuration Examples for Multilink Frame Relay over L2TPv3/AToM

•Additional References

•Command Reference

•Feature Information for Multilink Frame Relay over L2TPv3/AToM

Prerequisites for Configuring Multilink Frame Relay over L2TPv3/AToM

Before configuring Multilink Frame Relay over L2TPv3/AToM, you should understand how to configure Layer 2 virtual private networks (VPNs) and Multilink Frame Relay. See the "Additional References" section for pointers to the feature modules that explain how to configure and use those features.

Restrictions for Configuring Multilink Frame Relay over L2TPv3/AToM

•Only data-link connection identifier (DLCI)-to-DLCI switching, where each DLCI maps to its own pseudowire, is supported. Port-port mode (also known as HDLC mode), where the entire content of the port, including the Local Management Interface (LMI), is carried across a single pseudowire, is not supported.

•The following functionality is not supported:

–UNI/NNI or end-to-end fragmentation

–Nonstop forwarding/stateful switchover

–Four-byte DLCIs

•On the Cisco 7500 series routers, all bundle links must reside on the same port adapter (PA) of the Versatile Interface Processor (VIP). Links spreading across PAs are not supported.

•Cisco 7500 series routers support the VIP6-80, VIP4-80, VIP4-50, VIP2-50, CH-STM1, CT3/CE3, CT1/CE1, PA-4T+, and PA-8T port adapters.

•On the Cisco 12000 series routers, Multilink Frame Relay is supported only on the following pluggable modules: Cisco 4-port channelized T3 (DSO) shared port adapter, Cisco 8-port channelized T1/E1 shared port adapter, and the Cisco 1-port channelize OC-3/STM-1shared port adapter.

Information About Configuring Multilink Frame Relay over L2TPv3/AToM

To configure Multilink Frame Relay over L2TPv3/AToM, you need to understand the following concepts:

•Multilink Frame Relay over L2TPv3/AToM

•Internetworking Support for Multilink Frame Relay

•Quality of Service Support for Multilink Frame Relay over L2TPv3/AToM

Multilink Frame Relay over L2TPv3/AToM

Multilink Frame Relay over L2TPv3/AToM supports the following functionality:

•Permanent virtual circuit (PVC) status signaling

•LMI types cisco, q933a, and ANSI

•Sequencing

•Frame Relay policing (nondistributed)

•Type of service (ToS) marking for L2TPv3

Internetworking Support for Multilink Frame Relay

Interworking support for Multilink Frame Relay interfaces supports the following functionality:

•Frame Relay to Ethernet/VLAN (Ethernet and IP interworking)

•Frame Relay to PPP and ATM (IP interworking)

•Cisco and Internet Engineering Task Force (IETF) encapsulation on the customer-edge (CE) router

•Sequencing

•LMI interworking to notify CE routers of PVC status changes

Quality of Service Support for Multilink Frame Relay over L2TPv3/AToM

Note Quality of Service features are not supported in Cisco IOS Release 12.4(11)T.

L2VPN quality of service (QoS) features supported for Frame Relay are also supported with the Multilink Frame Relay over L2TPv3/AToM feature. You can attach an input service policy to the Multilink Frame Relay interface or individual DLCIs on the interface using the map-class mechanism to police or mark the traffic. You can attach an output policy to the Multilink Frame Relay (MFR) interface to perform class-based queueing, including per-DLCI queueing using the match fr-dlci command.

The following ingress QoS features are supported with the Multilink Frame Relay over L2TPv3/AToM feature:

•Interface input policy matching on the discard eligibility (DE) bit to set Multiprotocol Label Switching (MPLS) EXP or tunnel differentiated services code point (DSCP).

•Virtual circuit (VC) input policy configured with a color-aware, two-rate, three-color policer using the DE bit as input color and setting the MPLS EXP bit or tunnel DSCP bit based on color.

Note You cannot use the VC-level and interface-level input policies at the same time on the same interface.

The following egress QoS features are supported with the Multilink Frame Relay over L2TPv3/AToM feature:

•Egress queueing using tail drop or discard class-based weighted random early detection (WRED). You can use the latter with a core interface input policy to set the discard class based on the MPLS EXP or tunnel DSCP.

•Interface output policy matching on QoS group (selected by MPLS EXP or tunnel DSCP).

•Interface aggregate shaping policy with queueing policy.

•VC output shaping policy with tail drop or discard class-based WRED.

•Forward explicit congestion notification (FECN)/backward explicit congestion notification (BECN) marking.

Note You cannot use VC-level and interface-level output policies at the same time on the same interface.

Note Egress queueing and shaping policies are not supported with Multilink Frame Relay on the Cisco 7200 series routers.

How to Configure Multilink Frame Relay over L2TPv3/AToM

This section contains the following procedures:

•Configuring a Multilink Frame Relay Bundle Interface (required)

•Configuring a Multilink Frame Relay Bundle Link Interface (required)

•Connecting Frame Relay PVCs Between Routers (required)

•Verifying Multilink Frame Relay over L2TPv3/AToM (optional)

Configuring a Multilink Frame Relay Bundle Interface

Configure a bundle interface to aggregate bandwidth of multiple member links under a single interface to one virtual pipe. To configure a bundle interface for Multilink Frame Relay, perform the following steps.

SUMMARY STEPS

1. enable

2. configure terminal

3. interface mfr number

4. frame-relay multilink bid name

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

interface mfr number


Example:

Router(config)# interface mfr 1

Configures a multilink Frame Relay bundle interface and enters interface configuration mode.

Step 4 

frame-relay multilink bid name


Example:

Router(config-if)# frame-relay multilink bid int1


(Optional) Assigns a bundle identification name to a multilink Frame Relay bundle.

Note The bundle identification (BID) will not go into effect until the interface has gone from the down state to the up state. One way to bring the interface down and back up again is by using the shutdown and no shutdown commands in interface configuration mode.

Configuring a Multilink Frame Relay Bundle Link Interface

Configuring a Multilink Frame Relay bundle link interface allows you to combine bandwidth of multiple lower-speed serial links into a single large pipe and avoid the need of upgrading or purchasing new hardware. To configure a bundle link interface for Multilink Frame Relay, perform the following steps.

SUMMARY STEPS

1. enable

2. configure terminal

3. interface serial number

4. encapsulation frame-relay mfr number [name]

5. frame-relay multilink lid name

6. frame-relay multilink hello seconds

7. frame-relay multilink ack seconds

8. frame-relay multilink retry number

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

interface serial number

Example:

Router(config)# interface serial 1/1

Configures an interface and enters interface configuration mode.

Step 4 

encapsulation frame-relay mfr number [name]

Example:

Router(config-if)# encapsulation frame-relay mfr 1

Creates a multilink Frame Relay bundle link and associates the link with a bundle.

Tip To minimize latency that results from the arrival order of packets, we recommend bundling physical links of the same line speed in one bundle.

Step 5 

frame-relay multilink lid name

Example:

Router(config-if)# frame-relay multilink lid four

(Optional) Assigns a bundle link identification name with a multilink Frame Relay bundle link.

Note The bundle link identification (LID) will not go into effect until the interface has gone from the down state to the up state. One way to bring the interface down and back up again is by using the shutdown and no shutdown commands in interface configuration mode.

Step 6 

frame-relay multilink hello seconds

Example:

Router(config-if)# frame-relay multilink hello 20

(Optional) Configures the interval at which a bundle link will send out hello messages. The default value is 10 seconds.

Step 7 

frame-relay multilink ack seconds

Example:

Router(config-if)# frame-relay multilink ack 10

(Optional) Configures the number of seconds that a bundle link will wait for a hello message acknowledgment before resending the hello message. The default value is 4 seconds.

Step 8 

frame-relay multilink retry number

Example:

Router(config-if)# frame-relay multilink retry 5

(Optional) Configures the maximum number of times a bundle link will resend a hello message while waiting for an acknowledgment. The default value is 2 tries.

Connecting Frame Relay PVCs Between Routers

By connecting Frame Relay PVCs between routers, you can integrate Frame Relay over a Level 2 VPN backbone, which allows you to use your existing Frame Relay network without upgrading. To connect Frame Relay PVCs between routers, perform the following steps.

SUMMARY STEPS

1. enable

2. configure terminal

3. connect connection-name mfr number dlci l2transport

4. xconnect peer-router-id vcid encapsulation mpls

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

connect connection-name mfr number dlci l2transport

Example:

Router(config)# connect fr1 mfr 1 100 l2transport

Defines connections between Frame Relay PVCs.

•Using the l2transport keyword specifies that the PVC will not be a locally switched PVC, but will be tunneled over the backbone network.

•The connection-name argument is a text string that you provide.

•The dlci argument is the DLCI number of the PVC that will be connected.

Enters connect configuration submode.

Step 4 

xconnect peer-router-id vcid encapsulation mpls



Example:

Router(config-fr-pw-switching)# xconnect 10.0.0.1 123 encapsulation mpls

Creates the VC to transport the Layer 2 packets. In a DLCI-to-DLCI connection type, Frame Relay over MPLS uses the xconnect command in connect configuration submode.

Verifying Multilink Frame Relay over L2TPv3/AToM

To verify the configuration of Multilink Frame Relay, perform the following steps. The tunnel and session should be in the established (est) state.

SUMMARY STEPS

1. show l2tunnel

2. show mpls forwarding

DETAILED STEPS

Step 1 show l2tunnel

On both PE routers, use the following command to verify the configuration of Multilink Frame Relay over L2TPv3: 

PE1# show l2tunnel 


 Tunnel and Session Information Total tunnels 1 sessions 1


LocID RemID Remote Name   State  Remote Address  Port  Sessions L2TPclass

35788 41451 FRWI1         est    10.9.9.9         0     1        l2tp_default_cl


LocID      RemID      TunID      Username, Intf/         State 

                                 Vcid, Circuit                                  

8161       54072      35788      6, MF1:206              est   


PE2# show l2tunnel 


 Tunnel and Session Information Total tunnels 1 sessions 1


LocID RemID Remote Name   State  Remote Address  Port  Sessions L2TPclass

41451 35788 FRWI3         est    10.8.8.8         0     1                       


LocID      RemID      TunID      Username, Intf/          State 

                                 Vcid, Circuit                                  

54072      8161       41451      6, Fa0/1.6:6             est

Step 2 show mpls forwarding

On both PE routers, use the following command to verify the configuration of Multilink Frame Relay over MPLS: 

PE1# show mpls forwarding 


Local  Outgoing    Prefix            Bytes tag  Outgoing   Next Hop    

tag    tag or VC   or Tunnel Id      switched   interface

16     Pop tag     10.0.0.0/24       0          PO4/1/0    point2point  

17     Untagged    l2ckt(5)          0          MF1        point2point  

18     Untagged    l2ckt(6)          0          MF1        point2point  

19     17          10.9.9.9/32       0          PO4/1/0    point2point


PE2# show mpls forwarding 


Local  Outgoing    Prefix            Bytes tag  Outgoing   Next Hop    

tag    tag or VC   or Tunnel Id      switched   interface              

16     16          10.8.8.8/32       0          PO2/0      point2point  

17     Pop tag     10.13.0.0/24      0          PO2/0      point2point  

18     Untagged    l2ckt(5)          2244       MF2        point2point  

19     Untagged    l2ckt(6)          510        MF2        point2point

Configuration Examples for Multilink Frame Relay over L2TPv3/AToM

This section includes the following configuration examples:

•Frame Relay-to-Frame Relay over L2TPv3 on Multilink Frame Relay Interfaces: Example

•Frame Relay-to-Ethernet VLAN Interworking over L2TPv3 on Multilink Frame Relay Interfaces: Example

•Frame Relay-to-Ethernet Interworking over MPLS on Multilink Frame Relay Interfaces: Example

•MQC Color-Aware Policing: Example

•DE Bit Matching: Example

•DLCI-Based queueing: Example

•Discard Class-Based WRED: Example

•Aggregate Shaping: Example

•VC Shaping: Example

•FECN/BECN Marking: Example

Frame Relay-to-Frame Relay over L2TPv3 on Multilink Frame Relay Interfaces: Example

The following example sets up Multilink Frame Relay interfaces to transport Frame Relay data between PE routers:

PE1
PE2 
configure terminal

ip cef distributed

frame-relay switching

!

interface loopback 0

 ip address 10.8.8.8 255.255.255.255

 no shutdown

!

pseudowire-class fr-xconnect

 encapsulation l2tp

 protocol l2tpv3

 ip local interface loopback0

!

controller T3 1/1/1

t1 1 framing esf

t1 1 clock source internal

t1 1 channel-group 1 timeslots 1-24 speed 64

!

t1 2 framing esf

t1 2 clock source inter

t1 2 channel-group 1 timeslots 1-24 speed 64

!

interface mfr 1

 encapsulation frame-relay

 logging event dlci-status-change

 frame-relay intf-type nni

 no shutdown

!

interface Serial1/1/1/1:1

  encapsulation frame-relay mfr1

interface Serial1/1/1/2:1

  encapsulation frame-relay mfr1

!

interface POS4/1/0

 clock source internal

 ip address 10.13.0.0 255.255.255.0

 no shutdown

 no fair-queue

!

connect fr-fr mfr1 206 l2

 xconnect 10.9.9.9 6 pw-class fr-xconnect

!

router ospf 10

 network 10.13.0.0 0.0.0.0 area 0

 network 10.8.8.8 0.0.0.0 area 0

end

configure terminal

ip routing

ip cef

frame-relay switching

!

interface loopback 0

 ip address 10.9.9.9 255.255.255.255 

 no shutdown

!

interface p2/0

 clock source internal

 ip address 10.14.0.2 255.255.255.0

 no shutdown

 no fair-queue

!

controller T3 3/1

t1 1 framing esf

t1 1 clock source internal

t1 1 channel-group 1 timeslots 1-24 speed 64

!

t1 2 framing esf

t1 2 clock source internal

t1 2 channel-group 1 timeslots 1-24 speed 64

!

interface mfr2

 encapsulation frame-relay

 logging event dlci-status-change

 frame-relay intf-type dce

 no shutdown

!

interface serial3/1/1:1

 encapsulation frame-relay mfr2

!

interface s3/1/2:1

 encapsulation frame-relay mfr2

!

pseudowire-class fr-xconnect

 encapsulation l2tpv3

 protocol l2tpv3

 ip local interface loopback0

!

connect fr-fr mfr2 306 l2transport

 xconnect 10.8.8.8 6 pw-class fr-xconnect

!

router ospf 10

 network 10.14.0.2 0.0.0.0 area 0

 network 10.9.9.9 0.0.0.0 area 0

end

Frame Relay-to-Ethernet VLAN Interworking over L2TPv3 on Multilink Frame Relay Interfaces: Example

The following example sets up Multilink Frame Relay interfaces to perform Frame Relay-to-Ethernet VLAN interworking between PE routers. The example uses IP interworking, also referred to as routed interworking.      

PE1
PE2 
configure terminal

ip cef distributed

frame-relay switching

!

!

interface loopback 0

 ip address 10.8.8.8 255.255.255.255

 no shutdown

!

pseudowire-class ip

 encapsulation l2tp

 interworking ip

 ip local interface loopback0

!

interface mfr 1

 encapsulation frame-relay

 logging event dlci-status-change

 no shutdown

 frame-relay intf-type nni

!

interface Serial1/1/1/1:1

  encapsulation frame-relay mfr1

interface Serial1/1/1/2:1

  encapsulation frame-relay mfr1

!

interface POS4/1/0

 clock source internal

 ip address 13.0.0.2 255.255.255.0

 no shutdown

 no fair-queue

!

connect fr-vlan mfr1 206 l2

 xconnect 9.9.9.913.0.0.2 6 pw-class ip

!

router ospf 10

 network 10.13.0.2 0.0.0.0 area 0

 network 10.8.8.8 0.0.0.0 area 0

end

configure terminal

ip routing

ip cef

frame-relay switching

!

interface loopback 0

 ip address 10.9.9.9 255.255.255.255

 no shutdown

!

pseudowire-class ip

 encapsulation l2tp

 interworking ip

 ip local interface loopback0

!

interface p2/0

 clock source internal

 ip address 10.14.0.2 255.255.255.0

 no shutdown

 no fair-queue

!

interface FastEthernet0/1

  no shutdown 

!

interface FastEthernet0/1.6

 encapsulation dot1Q 6

 xconnect 10.8.8.8 6 pw-class ip

 no shutdown

!

router ospf 10

 network 10.14.0.2 0.0.0.0 area 0

 network 10.9.9.9 0.0.0.0 area 0

!

end

Frame Relay-to-Ethernet Interworking over MPLS on Multilink Frame Relay Interfaces: Example

The following example sets up Multilink Frame Relay interfaces to perform Frame Relay-to-Ethernet interworking between PE routers. The example uses IP interworking, also referred to as routed interworking.    

PE1
PE2 
configure terminal

ip cef distributed

frame-relay switching

!

!

interface loopback 0

 ip address 10.8.8.8 255.255.255.255

 no shutdown

!

interface mfr 1

 encapsulation frame-relay

 logging event dlci-status-change

 no shutdown

 frame-relay intf-type nni

!

interface Serial1/1/1/1:1

  encapsulation frame-relay mfr1

interface Serial1/1/1/2:1

  encapsulation frame-relay mfr2

!

interface POS4/1/0

 clock source internal

 ip address 10.13.0.2 255.255.255.0

 no shutdown

 mpls ip 

!

router ospf 10

 network 10.13.0.2 0.0.0.0 area 0

 network 10.8.8.8 0.0.0.0 area 0

!

mpls label protocol ldp

mpls ldp router-id loopback0

mpls ip

!

pseudowire-class atom

 encapsulation mpls

 interworking ip

!

connect fr-eth mfr1 207 l2

 xconnect 10.9.9.9 7 pw-class atom

!

end

configure terminal

ip routing

ip cef

frame-relay switching

!

interface loopback 0

 ip address 10.9.9.9 255.255.255.255

 no shutdown

!

interface POS2/0

 clock source internal

 ip address 10.14.0.2 255.255.255.0

 no shutdown

 no fair-queue

 mpls ip 

!

router ospf 10

 network 10.14.0.2 0.0.0.0 area 0

 network 10.9.9.9 0.0.0.0 area 0

!

mpls label protocol ldp

mpls ldp router-id loopback0

mpls ip

!

pseudowire-class atom

 encapsulation mpls

 interworking ip

!

interface FastEthernet0/1

 xconnect 10.8.8.8 7 pw-class atom

 no shutdown

!

end

MQC Color-Aware Policing: Example

Note Quality of Service features are not supported in Cisco IOS Release 12.4(11)T.

The following example configures a VC input policy with a color-aware, two-rate, three-color policing method using a DE bit as input color and setting the tunnel Differentiated Services Code Point (DSCP) based on color. Packets in excess of peak rates are discarded. 

class-map not-fr-de

match not fr-de

!

policy-map police

class class-default

police cir 64000 pir 256000

conform-color not-fr-de

conform-action set-dscp-tunnel-transmit  af31

exceed-action set-dscp-tunnel-transmit af32

violate-action drop

!

interface MFR1

frame-relay interface-dlci 206 switched

class police

!

connect fr-vlan mfr1 206 l2

xconnect 10.9.9.9 6 pw-class ip

!

map-class frame-relay police

service-policy input police

DE Bit Matching: Example

Note Quality of Service features are not supported in Cisco IOS Release 12.4(11)T.

The following example shows the configuration of an interface input policy matching on the DE bit to set the tunnel DSCP: 

class-map de

 match fr-de

!

policy-map de

 class de

  set ip dscp tunnel af32

 class class-default

  set ip dscp tunnel af31

!

interface MFR1

 service-policy input de

DLCI-Based queueing: Example

Note Quality of Service features are not supported in Cisco IOS Release 12.4(11)T.

The following example shows the configuration of an interface output policy matching on a QoS group based on the DLCI: 

class-map dlci100

 match fr-dlci 100

class-map dlci200

 match fr-dlci 200

!

policy-map dlci

 class dlci100

  bandwidth percent 10

 class dlci200

  bandwidth percent 20

!

interface MFR1

 service-policy output dlci

Discard Class-Based WRED: Example

Note Quality of Service features are not supported in Cisco IOS Release 12.4(11)T.

The following example shows the configuration of an interface output policy matching on a QoS group based on the tunnel DSCP: 

class-map conform

 match ip dscp af31

 match mpls experimental 4

class-map exceed

 match ip dscp af32

 match mpls experimental 3

class-map cos1

 match qos-group 1

!

policy-map core

 class conform

  set qos-group 1

  set discard-class 1

 class exceed

  set qos-group 1

  set discard-class 2

!

policy-map wred

 class cos1

  bandwidth percent 40

  random-detect discard-class-based

  random-detect discard-class 1 20 30 10

  random-detect discard-class 2 1 9 10

!

interface POS1/0

 service-policy input core

!

interface MFR1

 service-policy output wred

Aggregate Shaping: Example

Note Quality of Service features are not supported in Cisco IOS Release 12.4(11)T.

The following example shows the configuration of an interface aggregate shaping policy with a DLCI-based queueing policy: 

class-map dlci205

match fr-dlci 205

class-map dlci206

match fr-dlci 206

!

policy-map dlci

class dlci205

bandwidth 128

class dlci206

bandwidth 256

!

policy-map shape

class class-default

shape average 512000 2048 2048

service-policy dlci

!

interface MFR1

service-policy output shape

VC Shaping: Example

Note Quality of Service features are not supported in Cisco IOS Release 12.4(11)T.

The following example shows the configuration of a VC output shaping policy with discard class-based WRED: 

class-map conform

match mpls experimental 4

class-map exceed

match mpls experimental 3

class-map cos1

match qos-group 1

!

policy-map core

class conform

set qos-group 1

set discard-class 1

class exceed

set qos-group 1

set discard-class 2

!

policy-map vc-wred

class class-default

bandwidth percent 40

random-detect discard-class-based

random-detect discard-class 1 20 30 10

random-detect discard-class 2 1 9 10

!

policy-map shape

class class-default

shape average 512000 2048 2048

service-policy vc-wred

!

interface POS4/1/0

service-policy input core

!

interface MFR1

frame-relay interface-dlci 206 switched

class shape

!

map-class frame-relay shape

service-policy output shape

FECN/BECN Marking: Example

Note Quality of Service features are not supported in Cisco IOS Release 12.4(11)T.

The following example shows the configuration of an output policy that configures BECN and FECN bits: 

policy-map dlci

 class dlci100

  bandwidth percent 10

 class dlci200

  bandwidth percent 20

  set fr-fecn-becn 1

interface MFR1

 service-policy output dlci

 frame-relay congestion-management

  threshold ecn 20

Additional References

The following sections provide references related to the Multilink Frame Relay over L2TPv3/AToM feature.

Related Documents

Related Topic
Document Title

Multilink Frame Relay

•For the Cisco 7500 series routers:

Distributed Multilink Frame Relay (FRF.16)

•For the Cisco 7200 series routers:

Multilink Frame Relay (FRF.16)

L2VPN interworking

L2VPN Interworking

Layer 2 Tunneling Protocol, Version 3

L2TPV3

Layer 2 local switching

Layer 2 Local Switching


Standards

Standard
Title

draft-martini-l2circuit-trans-mpls-08.txt

Transport of Layer 2 Frames Over MPLS

draft-martini-l2circuit-encap-mpls-04.txt

Encapsulation Methods for Transport of Layer 2 Frames Over MPLS

draft-ietf-l2tpext-l2tp-base-03.txt

Layer Two Tunneling Protocol (Version 3)


MIBs

MIB
MIBs Link

•Cisco Frame Relay MIB (CISCO-FRAME-RELAY-MIB.my)

•Interfaces MIB (IF-MIB.my)

•MPLS LDP MIB (MPLS-LDP-MIB.my)

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs


RFCs

RFC
Title

RFC 2661

Layer Two Tunneling Protocol


Technical Assistance

Description
Link

The Cisco Technical Support & Documentation website contains thousands of pages of searchable technical content, including links to products, technologies, solutions, technical tips, and tools. Registered Cisco.com users can log in from this page to access even more content.

http://www.cisco.com/techsupport


Command Reference

The following commands are introduced or modified in the feature or features documented in this module. For information about these commands, see the Cisco IOS Multiprotocol Label Switching Command Reference at http://www.cisco.com/en/US/docs/ios/mpls/command/reference/mp_book.html. For information about all Cisco IOS commands, go to the Command Lookup Tool at http://tools.cisco.com/Support/CLILookup or to the Cisco IOS Master Commands List.

•xconnect

Feature Information for Multilink Frame Relay over L2TPv3/AToM

This feature enables Multilink Frame Relay switching over Layer 2 Tunnel Protocol Version 3 (L2TPv3) and Any Transport over MPLS (AToM). The feature works with like-to-like interfaces and disparate interfaces (L2VPN interworking).

Table 1 lists the release history for this feature.

Not all commands may be available in your Cisco IOS software release. For release information about a specific command, see the command reference documentation.

Cisco IOS software images are specific to a Cisco IOS software release, a feature set, and a platform. Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image support. Access Cisco Feature Navigator at http://www.cisco.com/go/fn. You must have an account on Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at the login dialog box and follow the instructions that appear.

Note Table 1 lists only the Cisco IOS software release that introduced support for a given feature in a given Cisco IOS software release train. Unless noted otherwise, subsequent releases of that Cisco IOS software release train also support that feature.

Table 1 Feature Information for Multilink Frame Relay over L2TPv3/AToM 

Feature Name
Releases
Feature Information

Multilink Frame Relay over L2TPv3/AToM

12.0(28)S
12.2(25)S
12.0(32)S
12.4(11)T

This feature was introduced in Cisco IOS Release 12.0(28)S for the Cisco 7200 and 7500 series routers.

This feature was integrated into Cisco IOS Release 12.2(25)S.

In Cisco IOS Release 12.0(32)S, this feature added support for the following pluggable modules for the Cisco 12000 series router: Cisco 4-port channelized T3 (DSO) shared port adapter, Cisco 8-port channelized T1/E1 shared port adapter, and the Cisco 1-port channelized OC-3/ STM-1 shared port adapter.

This feature was integrated into Cisco IOS Release 12.4(11)T.

Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image support.



Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

© 2007 Cisco Systems, Inc. All rights reserved.