Catalyst 6800ia接入埠上的QoS配置示例
下載選項
已更新: 2015 年 7 月 13 日
文件 ID:119140
無偏見用語
本產品的文件集力求使用無偏見用語。針對本文件集的目的，無偏見係定義為未根據年齡、身心障礙、性別、種族身分、民族身分、性別傾向、社會經濟地位及交織性表示歧視的用語。由於本產品軟體使用者介面中硬式編碼的語言、根據 RFP 文件使用的語言，或引用第三方產品的語言，因此本文件中可能會出現例外狀況。深入瞭解思科如何使用包容性用語。
關於此翻譯
思科已使用電腦和人工技術翻譯本文件，讓全世界的使用者能夠以自己的語言理解支援內容。請注意，即使是最佳機器翻譯，也不如專業譯者翻譯的內容準確。Cisco Systems, Inc. 對這些翻譯的準確度概不負責，並建議一律查看原始英文文件（提供連結）。
簡介
本文說明如何設定、驗證和疑難排解Cisco Catalyst 6800ia主機連線埠上的服務品質(QoS)。Cisco IOS®軟體版本152.1.SY中的6800ia主機連線埠以及Catalyst 6800父虛擬交換系統(VSS)上的更高版本支援QoS。
必要條件
需求
本文件沒有特定需求。
採用元件
本文中的資訊係根據以下軟體和硬體版本：
- Cisco IOS®軟體版本152.1.SY
- Cisco Catalyst 6800父VSS
本文中的資訊是根據特定實驗室環境內的裝置所建立。文中使用到的所有裝置皆從已清除（預設）的組態來啟動。如果您的網路正在作用，請確保您已瞭解任何指令可能造成的影響。
背景資訊
Catalyst 6800ia上的配置模式已禁用，並且6800ia主機埠的所有QoS配置都必須從父埠完成。6800ia主機埠的QoS使用策略對映進行配置。應用到介面時，此策略對映在內部將相關配置推送到6800ia，然後對硬體隊列進行程式設計。
6800ia主機埠在傳輸(TX)方向具有1p3q3t體系結構。本文中的所有組態範例僅適用於6800ia上的TX佇列。
當處於預設狀態的6800ia介面上不存在顯式QoS配置時，6800ia主機介面看起來與以下示例輸出類似：
6880-VSS#show run int gi101/1/0/1
interface GigabitEthernet101/1/0/1
switchport
switchport trunk allowed vlan 500
switchport mode access
switchport access vlan 500
load-interval 30
end
6880-VSS#show queueing interface gi101/1/0/1
Interface GigabitEthernet101/1/0/1 queueing strategy: Weighted Round-Robin
Port QoS is disabled globally
Queueing on Gi101/1/0/1: Tx Enabled Rx Disabled
Trust boundary disabled
Trust state: trust DSCP
Trust state in queueing: trust DSCP
Default COS is 0
Queueing Mode In Tx direction: mode-dscp
Transmit queues [type = 1p3q3t]:
Queue Id Scheduling Num of thresholds
-----------------------------------------
1 Priority 3
2 WRR 3
3 WRR 3
4 WRR 3
WRR bandwidth ratios: 100[queue 2] 100[queue 3] 100[queue 4] 0[queue 5]
queue-limit ratios: 15[Pri Queue] 25[queue 2] 40[queue 3] 20[queue 4]
queue thresh dscp-map
---------------------------------------
1 1 32 33 40 41 42 43 44 45 46 47
1 2
1 3
2 1 16 17 18 19 20 21 22 23 26 27 28 29 30 31 34 35 36 37 38 39
2 2 24
2 3 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
3 1 25
3 2
3 3 0 1 2 3 4 5 6 7
4 1 8 9 11 13 15
4 2 10 12 14
4 3
設定
配置示例1:隊列頻寬
此範例顯示如何設定6800ia TX佇列的頻寬：
- 設定class-maps以便對相關流量進行分類：
class-map type lan-queuing match-any ltest
match dscp 32
class-map type lan-queuing match-any ltest1
match dscp 24
class-map type lan-queuing match-any ltest2
match dscp default - 為已配置的類分配優先順序和頻寬：
policy-map type lan-queuing ltest
class type lan-queuing ltest
priority
class type lan-queuing ltest1
bandwidth remaining percent 30
class type lan-queuing ltest2
bandwidth remaining percent 20
class class-default - 將策略對映應用於6800ia介面：
附註：將lan-queueing policy-map套用到6800ia堆疊上的一個連線埠時，會將變更傳播到堆疊中的所有連線埠。
6880-VSS#conf t
6880-VSS(config)#int gi101/1/0/1
6880-VSS(config-if)#service-policy type lan-queuing output ltest
Propagating [attach] lan queueing policy "ltest" to Gi101/1/0/1 Gi101/1/0/2 Gi101/1/0/3
Gi101/1/0/4 Gi101/1/0/5 Gi101/1/0/6 Gi101/1/0/7 Gi101/1/0/8 Gi101/1/0/9 Gi101/1/0/10
Gi101/1/0/12 Gi101/1/0/13 Gi101/1/0/14 Gi101/1/0/15 Gi101/1/0/16 Gi101/1/0/17
Gi101/1/0/18 Gi101/1/0/19 Gi101/1/0/20 Gi101/1/0/21 Gi101/1/0/22 Gi101/1/0/23
Gi101/1/0/24 Gi101/1/0/25 Gi101/1/0/26 Gi101/1/0/27 Gi101/1/0/28 Gi101/1/0/29
Gi101/1/0/30 Gi101/1/0/31 Gi101/1/0/32 Gi101/1/0/33 Gi101/1/0/34 Gi101/1/0/35
Gi101/1/0/36 Gi101/1/0/37 Gi101/1/0/38 Gi101/1/0/39 Gi101/1/0/40 Gi101/1/0/41
Gi101/1/0/42 Gi101/1/0/43 Gi101/1/0/44 Gi101/1/0/45 Gi101/1/0/46 Gi101/1/0/47 Gi101/1/0/48
Propagating [attach] lan queueing policy "ltest" to Gi101/2/0/1 Gi101/2/0/2
Gi101/2/0/3 Gi101/2/0/4 Gi101/2/0/5 Gi101/2/0/6 Gi101/2/0/7 Gi101/2/0/8
Gi101/2/0/9 Gi101/2/0/10 Gi101/2/0/11 Gi101/2/0/12 Gi101/2/0/13 Gi101/2/0/14
Gi101/2/0/15 Gi101/2/0/16 Gi101/2/0/17 Gi101/2/0/18 Gi101/2/0/19 Gi101/2/0/20
Gi101/2/0/21 Gi101/2/0/22 Gi101/2/0/23 Gi101/2/0/24 Gi101/2/0/25 Gi101/2/0/26
Gi101/2/0/27 Gi101/2/0/28 Gi101/2/0/29 Gi101/2/0/30 Gi101/2/0/31 Gi101/2/0/32
Gi101/2/0/33 Gi101/2/0/34 Gi101/2/0/35 Gi101/2/0/36 Gi101/2/0/37 Gi101/2/0/38
Gi101/2/0/39 Gi101/2/0/40 Gi101/2/0/41 Gi101/2/0/42 Gi101/2/0/43 Gi101/2/0/44
Gi101/2/0/45 Gi101/2/0/46 Gi101/2/0/47 Gi101/2/0/48
Propagating [attach] lan queueing policy "ltest" to Gi101/3/0/1 Gi101/3/0/2
Gi101/3/0/3 Gi101/3/0/4 Gi101/3/0/5 Gi101/3/0/6 Gi101/3/0/7 Gi101/3/0/8
Gi101/3/0/9 Gi101/3/0/10 Gi101/3/0/11 Gi101/3/0/12 Gi101/3/0/13 Gi101/3/0/14
Gi101/3/0/15 Gi101/3/0/16 Gi101/3/0/17 Gi101/3/0/18 Gi101/3/0/19 Gi101/3/0/20
Gi101/3/0/21 Gi101/3/0/22 Gi101/3/0/23 Gi101/3/0/24 Gi101/3/0/25 Gi101/3/0/26
Gi101/3/0/27 Gi101/3/0/28 Gi101/3/0/29 Gi101/3/0/30 Gi101/3/0/31 Gi101/3/0/32
Gi101/3/0/33 Gi101/3/0/34 Gi101/3/0/35 Gi101/3/0/36 Gi101/3/0/37 Gi101/3/0/38
Gi101/3/0/39 Gi101/3/0/40 Gi101/3/0/41 Gi101/3/0/42 Gi101/3/0/43 Gi101/3/0/44
Gi101/3/0/45 Gi101/3/0/46 Gi101/3/0/47 Gi101/3/0/48
Propagating [attach] lan queueing policy "ltest" to Gi101/4/0/1 Gi101/4/0/2
Gi101/4/0/3 Gi101/4/0/4 Gi101/4/0/5 Gi101/4/0/6 Gi101/4/0/7 Gi101/4/0/8
Gi101/4/0/9 Gi101/4/0/10 Gi101/4/0/11 Gi101/4/0/12 Gi101/4/0/13 Gi101/4/0/14
Gi101/4/0/15 Gi101/4/0/16 Gi101/4/0/17 Gi101/4/0/18 Gi101/4/0/19 Gi101/4/0/20
Gi101/4/0/21 Gi101/4/0/22 Gi101/4/0/23 Gi101/4/0/24 Gi101/4/0/25 Gi101/4/0/26
Gi101/4/0/27 Gi101/4/0/28 Gi101/4/0/29 Gi101/4/0/30 Gi101/4/0/31 Gi101/4/0/32
Gi101/4/0/33 Gi101/4/0/34 Gi101/4/0/35 Gi101/4/0/36 Gi101/4/0/37 Gi101/4/0/38
Gi101/4/0/39 Gi101/4/0/40 Gi101/4/0/41 Gi101/4/0/42 Gi101/4/0/43 Gi101/4/0/44
Gi101/4/0/45 Gi101/4/0/46 Gi101/4/0/47 Gi101/4/0/48
6880-VSS(config-if)#
6880-VSS(config-if)#end - 驗證policy-map是否已應用：
6880-VSS#show run int gi101/1/0/1
interface GigabitEthernet101/1/0/1
switchport
switchport trunk allowed vlan 500
switchport mode access
switchport access vlan 500
load-interval 30
service-policy type lan-queuing output ltest
end - 檢查到隊列對映、頻寬和緩衝區分配以及到差分服務代碼點(DSCP)對映的類對映：
6880-VSS#show queueing int gi101/1/0/1
Interface GigabitEthernet101/1/0/1 queueing strategy: Weighted Round-Robin
Port QoS is disabled globally
Queueing on Gi101/1/0/1: Tx Enabled Rx Disabled
Trust boundary disabled
Trust state: trust DSCP
Trust state in queueing: trust DSCP
Default COS is 0
Class-map to Queue in Tx direction
Class-map Queue Id
----------------------------
ltest 1
ltest1 4
ltest2 3
class-default 2
Queueing Mode In Tx direction: mode-dscp
Transmit queues [type = 1p3q3t]:
Queue Id Scheduling Num of thresholds
-----------------------------------------
1 Priority 3
2 WRR 3
3 WRR 3
4 WRR 3
WRR bandwidth ratios: 50[queue 2] 20[queue 3] 30[queue 4]
queue-limit ratios: 15[Pri Queue] 100[queue 2] 100[queue 3] 100[queue 4]
queue thresh dscp-map
---------------------------------------
1 1 32
1 2
1 3
2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
23 25 26 27 28 29 30 31 33 34 35 36 37 38 39 40 41 42 43
44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
2 2
2 3
3 1 0
3 2
3 3
4 1 24
4 2
4 3 - 再次檢查6800ia的緩衝區和頻寬分配：
附註：如果不為特定類指定緩衝區權重，則預設情況下需要100%。
隊列1:15 / [15+100+100+100] = 4
隊列2:100 / [15+100+100] ~ 31
還衍生出其他隊列的權重。
6880-VSS#remote command fex 101 show mls qos int gi1/0/1 buffer
GigabitEthernet1/0/1
The port is mapped to qset : 1
The allocations between the queues are : 4 31 31 34
6880-VSS#remote command fex 101 show mls qos int gi1/0/1 queueing
GigabitEthernet1/0/1
Egress Priority Queue : enabled
Shaped queue weights (absolute) : 0 0 0 0
Shared queue weights : 0 127 51 76
The port bandwidth limit : 100 (Operational Bandwidth:100.0)
The port is mapped to qset : 1 - 驗證相關流量是否在各自的隊列中入隊，以及是否存在任何丟棄：
6880-VSS#remote command fex 101 show mls qos int gi1/0/1 statistic
GigabitEthernet1/0/1 (All statistics are in packets)
dscp: incoming
-------------------------------
0 - 4 : 0 0 0 0 0
5 - 9 : 0 0 0 0 0
10 - 14 : 0 0 0 0 0
15 - 19 : 0 0 0 0 0
20 - 24 : 0 0 0 0 0
25 - 29 : 0 0 0 0 0
30 - 34 : 0 0 0 0 0
35 - 39 : 0 0 0 0 0
40 - 44 : 0 0 0 0 0
45 - 49 : 0 0 0 13 0
50 - 54 : 0 0 0 0 0
55 - 59 : 0 0 0 0 0
60 - 64 : 0 0 0 0
dscp: outgoing
-------------------------------
0 - 4 : 0 0 0 0 0
5 - 9 : 0 0 0 0 0
10 - 14 : 0 0 0 0 0
15 - 19 : 0 0 0 0 0
20 - 24 : 0 0 0 0 9118500
25 - 29 : 0 0 0 0 0
30 - 34 : 0 0 516236 0 0
35 - 39 : 0 0 0 0 0
40 - 44 : 0 0 0 0 0
45 - 49 : 0 0 0 20 0
50 - 54 : 0 0 0 0 0
55 - 59 : 0 0 0 0 0
60 - 64 : 0 0 0 0
cos: incoming
-------------------------------
0 - 4 : 106 0 0 0 0
5 - 7 : 0 0 0
cos: outgoing
-------------------------------
0 - 4 : 41 0 0 9118505 516236
5 - 7 : 0 0 0
output queues enqueued:
queue: threshold1 threshold2 threshold3
-----------------------------------------------
queue 0: 516255 35 5
queue 1: 12 0 0
queue 2: 0 0 0
queue 3: 9118520 0 0
output queues dropped:
queue: threshold1 threshold2 threshold3
-----------------------------------------------
queue 0: 0 0 0
queue 1: 0 0 0
queue 2: 0 0 0
queue 3: 49823 0 0
Policer: Inprofile: 0 OutofProfile: 0
組態範例2:頻寬和緩衝區
此範例顯示如何為6800ia TX佇列設定頻寬和緩衝區：
- 在示例1中建立的策略對映中，可以指定隊列緩衝區分配，如以下示例所示：
附註：如果不為特定類指定緩衝區權重，則預設情況下需要100%。
policy-map type lan-queuing ltest
class type lan-queuing ltest
priority
queue-buffers ratio 15
class type lan-queuing ltest1
bandwidth remaining percent 30
queue-buffers ratio 30
class type lan-queuing ltest2
bandwidth remaining percent 20
queue-buffers ratio 40
class class-default
queue-buffer ratio 15 - 檢查到隊列對映、頻寬和緩衝區分配以及隊列到DSCP對映的類對映：
6880-VSS#sh queueing int gi101/1/0/1
Interface GigabitEthernet101/1/0/1 queueing strategy: Weighted Round-Robin
Port QoS is disabled globally
Queueing on Gi101/1/0/1: Tx Enabled Rx Disabled
Trust boundary disabled
Trust state: trust DSCP
Trust state in queueing: trust DSCP
Default COS is 0
Class-map to Queue in Tx direction
Class-map Queue Id
----------------------------
ltest 1
ltest1 4
ltest2 3
class-default 2
Queueing Mode In Tx direction: mode-dscp
Transmit queues [type = 1p3q3t]:
Queue Id Scheduling Num of thresholds
-----------------------------------------
1 Priority 3
2 WRR 3
3 WRR 3
4 WRR 3
WRR bandwidth ratios: 50[queue 2] 20[queue 3] 30[queue 4]
queue-limit ratios: 15[Pri Queue] 15[queue 2] 40[queue 3] 30[queue 4]
queue thresh dscp-map
---------------------------------------
1 1 32
1 2
1 3
2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
22 23 25 26 27 28 29 30 31 33 34 35 36 37 38 39 40 41
42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
2 2
2 3
3 1 0
3 2
3 3
4 1 24
4 2
4 3 - 再次檢查6800ia的緩衝區和頻寬分配：
6880-VSS#remote command fex 101 sh mls qos int gi1/0/1 queueing
GigabitEthernet1/0/1
Egress Priority Queue : enabled
Shaped queue weights (absolute) : 0 0 0 0
Shared queue weights : 0 127 51 76
The port bandwidth limit : 100 (Operational Bandwidth:100.0)
The port is mapped to qset : 1
6880-VSS#remote command fex 101 sh mls qos int gi1/0/1 buffers
GigabitEthernet1/0/1
The port is mapped to qset : 1
The allocations between the queues are : 15 15 40 30 - 驗證相關流量是否在各自的隊列中入隊，以及是否存在任何丟棄：
6880-VSS#remote command fex 101 sh mls qos int gi1/0/1 statistic
GigabitEthernet1/0/1 (All statistics are in packets)
dscp: incoming
-------------------------------
0 - 4 : 0 0 0 0 0
5 - 9 : 0 0 0 0 0
10 - 14 : 0 0 0 0 0
15 - 19 : 0 0 0 0 0
20 - 24 : 0 0 0 0 0
25 - 29 : 0 0 0 0 0
30 - 34 : 0 0 0 0 0
35 - 39 : 0 0 0 0 0
40 - 44 : 0 0 0 0 0
45 - 49 : 0 0 0 491 0
50 - 54 : 0 0 0 0 0
55 - 59 : 0 0 0 0 0
60 - 64 : 0 0 0 0
dscp: outgoing
-------------------------------
0 - 4 : 0 0 0 0 0
5 - 9 : 0 0 0 0 0
10 - 14 : 0 0 0 0 0
15 - 19 : 0 0 0 0 0
20 - 24 : 0 0 0 0 57864687
25 - 29 : 0 0 0 0 0
30 - 34 : 0 0 29364400 0 0
35 - 39 : 0 0 0 0 0
40 - 44 : 0 0 0 0 0
45 - 49 : 0 0 0 775 0
50 - 54 : 0 0 0 0 0
55 - 59 : 0 0 0 0 0
60 - 64 : 0 0 0 0
cos: incoming
-------------------------------
0 - 4 : 5323 0 0 0 0
5 - 7 : 0 0 0
cos: outgoing
-------------------------------
0 - 4 : 1718 0 0 57864691 29364400
5 - 7 : 0 0 0
output queues enqueued:
queue: threshold1 threshold2 threshold3
-----------------------------------------------
queue 0: 29365402 1883 5
queue 1: 793 98 0
queue 2: 0 0 0
queue 3: 530554174 0 0
output queues dropped:
queue: threshold1 threshold2 threshold3
-----------------------------------------------
queue 0: 0 10 0
queue 1: 1 24093 0
queue 2: 0 0 0
queue 3: 2309351 0 0
Policer: Inprofile: 0 OutofProfile: 0
驗證
目前沒有適用於此組態的驗證程序。
疑難排解
本節提供的資訊可用於對組態進行疑難排解。
輸出直譯器工具(僅供已註冊客戶使用)支援某些show命令。使用輸出直譯器工具來檢視show命令輸出的分析。
附註：使用 debug 指令之前，請先參閱有關 Debug 指令的重要資訊。
- 從6800ia CLI為qos-manager啟用debug。確保日誌被重定向到緩衝區，並且日誌緩衝區設定為高數：
6880-VSS#attach fex 101
Attach FEX:101 ip:192.168.1.101
Trying 192.168.1.101 ... Open
????????FEX-101>en
Password: cisco
FEX-101#
FEX-101#debug platform qos-manager all
QM verbose debugging is on
QM cops debugging is on
QM events debugging is on
QM Statistics debugging is on
FEX-101#exit
[Connection to 192.168.1.101 closed by foreign host] - 配置policy-map以觸發調試：
6880-VSS#conf t
6880-VSS(config)#int gi101/1/0/1
6880-VSS(config-if)# service-policy type lan-queuing output ltest
Propagating [attach] lan queueing policy "ltest" to Gi101/1/0/1
Gi101/1/0/2 Gi101/1/0/3 Gi101/1/0/4 Gi101/1/0/5 Gi101/1/0/6 Gi101/1/0/7 Gi101/1/0/8
Gi101/1/0/9 Gi101/1/0/10 Gi101/1/0/12 Gi101/1/0/13 Gi101/1/0/14 Gi101/1/0/15 Gi101/1/0/16
<snip>
6880-VSS(config-if)#end - 檢查交換矩陣擴展器(FEX)上的日誌以檢查調試：
6880-VSS#remote command fex 101 show log
<snip>
May 20 06:43:18.208: HQM: hulc_fex_qos_priority_handler: hulc_fex_qos_priority_handler:
****Setting Priority Queue (FEX-101)
May 20 06:43:18.208: HQM: hulc_fex_qos_priority_handler: hulc_fex_qos_priority_handler:
subopcode=2 startport=0 endport=0 size=4 (FEX-101)
May 20 06:43:18.208: HQM: hulc_f
_fex_qos_priority_handler:QueueNum=1 PriorityQueue=1 queuetype=2 thresholdsnum=3 (FEX-101)
May 20 06:43:18.212: HQM: hulc_fex_qos_priority_handler: hulc_fex_qos_priority_handler:
idb=GigabitEthernet1/0/1 (FEX-101)
May 20 06:43:18.212: HQM: hulc_fex_qos_priority_handler: hulc_fex_qos_priority_handler:
idb=GigabitEthernet1/0/2 (FEX-101)
May 20 06:43:18.212: HQM: hulc_fex_qos_priority_handler: hulc_fex_qos_priority_handler:
idb=GigabitEthernet1/0/3 (FEX-101)
<snip>hulc_fex_qos_srr_weight_setting:****Setting weight for queues**** (FEX-101)
May 20 06:43:18.232: HQM: hulc_fex_qos_srr_weight_setting: hulc_fex_qos_srr_weight_setting:
subopcode=2 startport=0 endport=0 size=4 (FEX-101)
May 20 06:43:18.232: HQM: hulc_fex_qos_srr_weight_setting: hulc_fex_qos_srr_weight_setting:
QueueNum=1 RRType=0 WeightRelative=0 WeightAbsolute=0 (FEX-101)
20 06:43:18.232: HQM: hulc_fex_qos_srr_weight_setting: hulc_fex_qos_srr_weight_setting:
ratio is 0 for queue 1 (FEX-101)
May 20 06:43:18.232: HQM: hulc_fex_qos_srr_weight_setting: hulc_fex_qos_srr_weight_setting:
QueueNum=2 RRType=0 WeightRelative=33 WeightAbsolute=0 (FEX-101)
<snip>20 06:43:19.110: HQM: hulc_fex_qos_buffer_conf: **Setting buffer for output queues** (FEX-101)
May 20 06:43:19.110: HQM: hulc_fex_qos_buffer_conf: hulc_fex_qos_buffer_conf:
subopcode=2 startport=0 endport=0 size=4 (FEX-101)
May 20 06:43:19.110: HQM: hulc_fex_qos_buffer_conf: hulc_fex_qos_buffer_conf:
queuenum=1 size=15 (FEX-101)
May 20 06:43:19.110: HQM: hulc_fex_qos_buffer_conf:
hulc_fex_qos_buffer_conf: queuenum=2 size=25 (FEX-101)
May 20 06:43:19.110: HQM: hulc_fex_qos_buffer_conf:
hulc_fex_qos_buffer_conf: queuenum=3 size=40 (FEX-101)
May 20 06:43:19.110: HQM: hulc_fex_qos_buffer_conf:
hulc_fex_qos_buffer_conf: queuenum=4 size=20 (FEX-101)
May 20 06:43:19.110: HQM: hqm
20 06:43:19.113: HQM: s88g_qd_get_queue_threshold: s88g_qd_get_queue_threshold:
max_limit = 3200, set to 350. (FEX-101)
May 20 06:43:19.113: HQM: s88g_qd_get_queue_threshold: s88g_qd_get_queue_threshold:
max_limit = 3200, set to 350. (FEX-101)
<snip>hulc_fex_qos_qthresh_map:****Setting dscp to output queue map**** (FEX-101)
May 20 06:43:19.169: HQM: hulc_fex_qos_qthresh_map: hulc_fex_qos_qthresh_map:
subopcode=2 startport=0 endport=0 size=1 (FEX-101)
May 20 06:43:19.169: HQM: hulc_fex_qos_qthresh_map: hulc_fex_qos_qthresh_map: DscpBma
20 06:43:19.169: HQM: hulc_fex_qos_qthresh_map: hulc_fex_qos_qthresh_map
dscp=32 iterator=0 (FEX-101)
May 20 06:43:19.169: HQM: hulc_fex_qos_qthresh_map: hulc_fex_qos_qthresh_map
dscp=33 iterator=1 (FEX-101)
May 20 06:43:19.169: HQM: hulc_fex_qos_qthresh_map: hulc_fex_qos_qthresh_map
dscp=40 iterator=2 (FEX-101)
<snip>
修訂記錄
| 修訂 | 發佈日期 | 意見 |
|---|---|---|
1.0 |
13-Jul-2015 |
初始版本 |
意見