有關在MDS交換機中優先傳輸B2B信用額度的技術說明

簡介

本檔案介紹不同介面中的接收和傳輸緩衝區到緩衝區(B2B)信用，當您對光纖通道網狀架構中的效能問題進行疑難排解時，這些信用非常有用。

必要條件

需求

思科建議您瞭解以下主題：

• Cisco多層次資料交換器(MDS)
• 光纖通道協定

採用元件

本檔案中的資訊是根據Cisco MDS 9000系列多層次交換器。

本文中的資訊是根據特定實驗室環境內的裝置所建立。文中使用到的所有裝置皆從已清除（預設）的組態來啟動。如果您的網路運作中，請確保您瞭解任何指令可能造成的影響。

瞭解MDS交換機中的優先順序傳輸B2B信用

對光纖通道交換矩陣網路的慢排問題進行故障排除時，MDS交換機中的show interface命令是確認介面可用積分的一種簡單方法。

以下說明在MDS介面中傳輸B2B信用。

適用於交換器間連結通訊協定(ISL)中繼介面

低優先順序信用用於資料流量，高優先順序信用用於交換機間鏈路控制流量。這只是傳送方端的一個邏輯除法器，用以限制其自身，使其不會消耗接收方上的所有可用接收(Rx)信用。

例如，交換機MDS Tempest（接收器）通知交換機MDS Maestro（傳送方）它有64個Rx信用點。

交換機MDS Maestro將56個信用標籤為低優先順序傳輸(Tx)信用和8個標籤為高優先順序Tx信用。

出現擁塞時，MDS Maestro在56個低優先順序信用均不可用時停止傳送資料流量。

但是，它仍可以使用可用的8個高優先順序信用點向MDS Tempest傳送控制流量。

MDS Tempest無需區分低優先順序信用或高優先順序信用。

附註：高優先順序TX傳輸信用的數量取決於不同的硬體平台。

這是一般的理念：八分之一的TX傳輸信用將為高優先順序信用，最大值為15 — 足以處理ELP或其他ISL控制消息。

這種高/低優先順序差異僅用於E埠或TE埠之間的ISL鏈路，不用於F埠。

MDS 9148S平台示例：

對於E埠介面：

Tempest# show int fc1/26
fc1/26 is trunking
    Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN)
    Port WWN is 20:1a:00:2a:6a:b9:d2:30
    Peer port WWN is 20:1a:00:2a:6a:56:f0:00
    Admin port mode is auto, trunk mode is on
    snmp link state traps are enabled
    Port mode is TE
    Port vsan is 2
    Admin Speed is auto
    Operating Speed is 4 Gbps
    Rate mode is dedicated
    Port flow-control is R_RDY

    Transmit B2B Credit is 32
    Receive B2B Credit is 64
    B2B State Change Number is 14
    Receive data field Size is 2112
    Beacon is turned off
    Logical type is core
    Trunk vsans (admin allowed and active) (2)
    Trunk vsans (up)                       (2)
    Trunk vsans (isolated)                 ()
    Trunk vsans (initializing)             ()
    5 minutes input rate 160 bits/sec,20 bytes/sec, 0 frames/sec
    5 minutes output rate 96 bits/sec,12 bytes/sec, 0 frames/sec
      22464 frames input,1801536 bytes
        0 discards,0 errors
        0 invalid CRC/FCS,0 unknown class
        0 too long,0 too short
      22977 frames output,1318564 bytes
        0 discards,0 errors
      0 input OLS,0  LRR,0 NOS,2 loop inits
      1 output OLS,2 LRR, 0 NOS, 1 loop inits
      64 receive B2B credit remaining
      32 transmit B2B credit remaining
      28 low priority transmit B2B credit remaining
    Interface last changed at Thu Jul 20 15:40:32 2017

    Last clearing of "show interface" counters :  never

Tempest#

   鏈路另一端顯示總傳輸信用為64，低優先順序為56:

Maestro# show int fc1/26
fc1/26 is trunking
    Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN)
    Port WWN is 20:1a:00:2a:6a:56:f0:00
    Peer port WWN is 20:1a:00:2a:6a:b9:d2:30
    Admin port mode is auto, trunk mode is on
    snmp link state traps are enabled
    Port mode is TE
    Port vsan is 2
    Speed is 4 Gbps
    Rate mode is dedicated
    Transmit B2B Credit is 64
    Receive B2B Credit is 32
    B2B State Change Number is 14
    Receive data field Size is 2112
    Beacon is turned off
    admin fec state is down
    oper fec state is down
    Trunk vsans (admin allowed and active) (2)
    Trunk vsans (up)                       (2)
    Trunk vsans (isolated)                 ()
    Trunk vsans (initializing)             ()
    5 minutes input rate 160 bits/sec,20 bytes/sec, 0 frames/sec
    5 minutes output rate 216 bits/sec,27 bytes/sec, 0 frames/sec
      23189 frames input,1330368 bytes
        0 discards,0 errors
        0 invalid CRC/FCS,0 unknown class
        0 too long,0 too short
      22677 frames output,1818076 bytes
        0 discards,0 errors
      1 input OLS,2  LRR,0 NOS,3 loop inits
      1 output OLS,0 LRR, 0 NOS, 1 loop inits
      32 receive B2B credit remaining
      64 transmit B2B credit remaining
      56 low priority transmit B2B credit remaining
    Interface last changed at Wed Jul 19 16:39:58 2017

    Last clearing of "show interface" counters 1w 5d

Maestro#

對於F埠介面：

對於F埠，此計算不適用，因為MDS交換機和啟動器/目標裝置之間沒有控制流量。

但是，您可以看到F埠中標籤為資料流量低優先順序的所有傳輸信用。

例如，以下輸出中的總傳輸信用3和低優先順序為3:

switch# show int fc1/47
fc1/47 is up
    Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN)
    Port WWN is 20:2f:00:2a:6a:56:f0:00
    Admin port mode is F, trunk mode is on
    snmp link state traps are enabled
    Port mode is F, FCID is 0x570f00
    Port vsan is 2
    Speed is 4 Gbps
    Rate mode is dedicated
    Transmit B2B Credit is 3
    Receive B2B Credit is 32
    Receive data field Size is 2112
    Beacon is turned off
    admin fec state is down
    oper fec state is down
    5 minutes input rate 0 bits/sec,0 bytes/sec, 0 frames/sec
    5 minutes output rate 16 bits/sec,2 bytes/sec, 0 frames/sec
      1220 frames input,74256 bytes
        0 discards,0 errors
        0 invalid CRC/FCS,0 unknown class
        0 too long,0 too short
      2231 frames output,220056 bytes
        0 discards,0 errors
      1 input OLS,1  LRR,0 NOS,0 loop inits
      1 output OLS,0 LRR, 1 NOS, 0 loop inits
      32 receive B2B credit remaining
      3 transmit B2B credit remaining 
      3 low priority transmit B2B credit remaining
    Interface last changed at Wed Jul 19 15:56:15 2017

    Last clearing of "show interface" counters 1w 5d

switch#

 MDS 9710交換機示例：

MDS97xx交換機中沒有高優先順序Tx傳輸信用。但是，可以使用system default tx-credit double-queue 指令更改此設定。

所連線交換器的介面也可以看到最大Tx傳輸信用額。

拓撲：  MDS 9710 Leonard fc3/14通過E埠背靠背連線到MDS 9148S Tempest fc1/13。

預設設定：

預設情況下，MDS 9710 DS-X9448-768K9線卡沒有高優先順序信用，所有64個傳輸信用均被視為低優先順序。 

Leonard(config-if)# show int fc3/14 counter
fc3/14
    5 minutes input rate 320 bits/sec, 40 bytes/sec, 3 frames/sec
    5 minutes output rate 2688 bits/sec, 336 bytes/sec, 3 frames/sec
    1416819 frames input, 77233324 bytes
      0 discards, 0 errors, 0 CRC/FCS
      0 unknown class, 0 too long, 0 too short
    1416813 frames output, 138598368 bytes
      0 discards, 0 errors
    0 timeout discards, 0 credit loss
    53 input OLS, 85 LRR, 119 NOS, 0 loop inits
    77 output OLS, 7 LRR, 93 NOS, 0 loop inits
    14 link failures, 37 sync losses, 2 signal losses
     140 Transmit B2B credit transitions to zero
     92 Receive B2B credit transitions to zero
      0 2.5us TxWait due to lack of transmit credits
      Percentage Tx credits not available for last 1s/1m/1h/72h: 0%/0%/0%/0%
      500 receive B2B credit remaining
      64 transmit B2B credit remaining
      64 low priority transmit B2B credit remaining
    Last clearing of "show interface" counters : never
Leonard(config-if)#

使用tx-credit double-queue:

在交換機上發出命令後，Leonard系統預設的tx-credit雙隊列

（需要通過shut/no shut重置介面）

Leonard(config)# show system default switchport
System default port state is down
System default trunk mode is on
System default link failure syslog logging level is 5
System default tx credit queue type is 0
Leonard(config)# system default tx-credit double-queue
Leonard(config)# show system default switchport
System default port state is down
System default trunk mode is on
System default link failure syslog logging level is 5
System default tx credit queue type is 1
Leonard(config)# int fc3/14
Leonard(config-if)# shut
Leonard(config-if)# no shut

可以看到，有8個高優先順序Tx傳輸B2B信用和56個低優先順序信用：

Leonard(config-if)# show int fc3/14 counter
fc3/14
    5 minutes input rate 320 bits/sec, 40 bytes/sec, 2 frames/sec
    5 minutes output rate 256 bits/sec, 32 bytes/sec, 2 frames/sec
    1420613 frames input, 77459300 bytes
      0 discards, 0 errors, 0 CRC/FCS
      0 unknown class, 0 too long, 0 too short
    1420607 frames output, 138968464 bytes
      0 discards, 0 errors
    0 timeout discards, 0 credit loss
    54 input OLS, 87 LRR, 122 NOS, 0 loop inits
    79 output OLS, 7 LRR, 95 NOS, 0 loop inits
    14 link failures, 38 sync losses, 2 signal losses
     143 Transmit B2B credit transitions to zero
     94 Receive B2B credit transitions to zero
      0 2.5us TxWait due to lack of transmit credits
      Percentage Tx credits not available for last 1s/1m/1h/72h: 0%/0%/0%/0%
      500 receive B2B credit remaining
      64 transmit B2B credit remaining
      56 low priority transmit B2B credit remaining
    Last clearing of "show interface" counters : never
Leonard(config-if)#

來自交換機MDS 9148S Tempest的最大RX傳輸積分為15:

從連線的MDS 9148S，Tempest可以看出，最大Tx傳輸B2B信用為15。

預設情況下，MDS9710交換機Leonard有500個接收信用點，因此MDS9148S交換機Tempest還將有500個Tx傳輸B2B信用點剩餘，但15個信用點（最大值）被分配為高優先順序(500 - 485 = 15)。

Tempest# show int fc1/13 counter
fc1/13
    5 minutes input rate 2624 bits/sec, 328 bytes/sec, 3 frames/sec
    5 minutes output rate 1504 bits/sec, 188 bytes/sec, 3 frames/sec
    1343331 frames input, 131489464 bytes
      0 discards, 0 errors, 0 CRC/FCS
      0 unknown class, 0 too long, 0 too short
    1343332 frames output, 72878124 bytes
      0 discards, 0 errors
    0 timeout discards, 0 credit loss
    9 input OLS, 2 LRR, 0 NOS, 0 loop inits
    12 output OLS, 20 LRR, 9 NOS, 0 loop inits
    9 link failures, 0 sync losses, 0 signal losses
     66 Transmit B2B credit transitions to zero
     24 Receive B2B credit transitions to zero
      0 2.5us TxWait due to lack of transmit credits
      Percentage Tx credits not available for last 1s/1m/1h/72h: 0%/0%/0%/0%
      64 receive B2B credit remaining
      500 transmit B2B credit remaining
      485 low priority transmit B2B credit remaining
    Last clearing of "show interface" counters  :never
Tempest#

當從MDS 9710 Leonard接收的積分更改為低於120時，八分之一的Tx積分將被標籤為高優先順序：

Leonard(config)# int fc3/14
Leonard(config-if)# switchport fcrxbbcredit 112

Tempest# show int fc1/13 count
fc1/13
    5 minutes input rate 1024 bits/sec, 128 bytes/sec, 3 frames/sec
    5 minutes output rate 1536 bits/sec, 192 bytes/sec, 3 frames/sec
    1360026 frames input, 133105756 bytes
      0 discards, 0 errors, 0 CRC/FCS
      0 unknown class, 0 too long, 0 too short
    1360027 frames output, 73885304 bytes
      0 discards, 0 errors
    0 timeout discards, 0 credit loss
    14 input OLS, 2 LRR, 0 NOS, 0 loop inits
    17 output OLS, 30 LRR, 14 NOS, 0 loop inits
    14 link failures, 0 sync losses, 0 signal losses
     91 Transmit B2B credit transitions to zero
     34 Receive B2B credit transitions to zero
      0 2.5us TxWait due to lack of transmit credits
      Percentage Tx credits not available for last 1s/1m/1h/72h: 0%/0%/0%/0%
      64 receive B2B credit remaining
      112 transmit B2B credit remaining
      98 low priority transmit B2B credit remaining
    Last clearing of "show interface" counters  :never
Tempest#