ASA/PIX 7.x及更高版本：LAN到LAN和EasyVPN IPSec隧道终止在同样接口配置示例

下载选项

  • PDF     (275.0 KB)
    在各种设备上使用 Adobe Reader 查看
  • ePub     (114.7 KB)
    在 iPhone、iPad、Android、Sony Reader 或 Windows Phone 上使用各种应用查看
  • Mobi (Kindle)     (125.2 KB)
    在 Kindle 设备上查看或在多个设备上使用 Kindle 应用查看
已更新: 2008 年 9 月 30 日
文档 ID:100313

非歧视性语言

此产品的文档集力求使用非歧视性语言。在本文档集中，非歧视性语言是指不隐含针对年龄、残障、性别、种族身份、族群身份、性取向、社会经济地位和交叉性的歧视的语言。由于产品软件的用户界面中使用的硬编码语言、基于 RFP 文档使用的语言或引用的第三方产品使用的语言，文档中可能无法确保完全使用非歧视性语言。 深入了解思科如何使用包容性语言。

关于此翻译

思科采用人工翻译与机器翻译相结合的方式将此文档翻译成不同语言，希望全球的用户都能通过各自的语言得到支持性的内容。 请注意：即使是最好的机器翻译，其准确度也不及专业翻译人员的水平。 Cisco Systems, Inc. 对于翻译的准确性不承担任何责任，并建议您总是参考英文原始文档（已提供链接）。

简介

本文提供了一个示例配置，以介绍如何使 HUB ASA 在相同接口上接受站点到站点隧道和 Easy VPN IPSec 连接。Cisco ASA 5520 和 Cisco 自适应安全设备 (ASA) 5505 之间的 IPsec 使用带有网络扩展模式 (NEM) 的 Easy VPN。

先决条件

要求

本文档没有任何特定的要求。

使用的组件

本文档中的信息基于以下软件和硬件版本：

  • 运行 7.x 版本及更高版本的 ASA 5500 系列（集线器）

    注意：HUB ASA配置也可与运行7.x及更高版本的PIX安全设备515、515E、525和535一起使用

  • 运行 7.x 版本及更高版本的 Easy VPN ASA 5505

  • 运行 7.x 版本及更高版本的 PIX 安全工具 515、515E、525 和 535

本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始（默认）配置。如果您使用的是真实网络，请确保您已经了解所有命令的潜在影响。

规则

有关文档约定的更多信息，请参考 Cisco 技术提示约定。

配置

本部分提供了可用于配置本文所述功能的信息。

注意：要获取有关本部分中所使用命令的更多信息，可使用命令查找工具（仅限已注册客户）。

网络图

本文档使用以下网络设置：

pixasa_easy_l2l_vpn1.gif

注意：此配置中使用的IP编址方案在Internet上不可合法路由。这些地址是在实验室环境中使用的 RFC 1918 地址。 leavingcisco.com

配置

本文档使用以下配置：

HUB ASA 
ASA Version 8.0(2)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
names
!
interface Ethernet0/0
 nameif outside
 security-level 0
 ip address 10.1.1.1 255.255.255.0
!
interface Ethernet0/1
 nameif inside
 security-level 100
 ip address 192.168.2.1 255.255.255.0
!

!--- Output Suppressed.


 !--- Access-list for interesting traffic (Site to Site) to be !--- encrypted between hub ASA and spoke (PIX) networks.

access-list outside_cryptomap_20 extended permit ip 192.168.2.0 255.255.255.0 
 192.168.1.0 255.255.255.0

 !--- Access-list for interesting traffic to be !--- encrypted between hub ASA and spoke easy vpn client ASA networks.


access-list ezvpn1 extended permit ip 192.168.2.0 255.255.255.0 192.168.3.0
 255.255.255.0


!--- Access-list for traffic to bypass the network address !--- translation (NAT) process.
 
access-list nonat extended permit ip 192.168.2.0 255.255.255.0 192.168.1.0
 255.255.255.0
access-list nonat extended permit ip 192.168.2.0 255.255.255.0 192.168.3.0
 255.255.255.0

!--- Output Suppressed.


!--- Specify the NAT configuration. !--- NAT 0 prevents NAT for the ACL defined in this configuration. !--- The nat 1 command specifies NAT for all other traffic.


nat-control
global (outside) 1 interface
nat (inside) 0 access-list nonat
nat (inside) 1 0.0.0.0 0.0.0.0

route outside 0.0.0.0 0.0.0.0 10.1.1.2 1



!--- Output Suppressed.


!--- Configuration of IPsec Phase 2

crypto ipsec transform-set myset esp-3des esp-sha-hmac

!--- IPsec configuration for the dynamic LAN-to-LAN tunnel

crypto dynamic-map ezvpn 30 set transform-set myset

!--- IPsec configuration for the static LAN-to-LAN tunnel

crypto map outside_map 20 match address outside_cryptomap_20
crypto map outside_map 20 set peer 172.16.1.1
crypto map outside_map 20 set transform-set myset

!--- IPsec configuration that binds dynamic map to crypto map

crypto map outside_map 65535 ipsec-isakmp dynamic ezvpn

!--- Crypto map applied to the outside interface of the ASA

crypto map outside_map interface outside

isakmp enable outside

!--- PHASE 1 CONFIGURATION ---! !--- This configuration uses isakmp policy 1. !--- These configuration commands !--- define the Phase 1 policies that are used. 

crypto isakmp policy 10
 authentication pre-share
 encryption 3des
 hash sha
 group 2
 lifetime 86400



!--- Output Suppressed.



!--- This defines the group policy you use with Easy VPN. !--- Specify the networks that can pass through !--- the tunnel and that you want to !--- use network extension mode.


group-policy tunnel internal
group-policy tunnel attributes
 nem enable

!--- The username and password associated with !--- this VPN connection are defined here. You !--- can also use AAA for this function. 

username cisco password ffIRPGpDSOJh9YLq encrypted

tunnel-group 172.16.1.1 type ipsec-l2l
tunnel-group 172.16.1.1 ipsec-attributes
 pre-shared-key *


!--- The tunnel-group commands bind the configurations !--- defined in this configuration to the tunnel that is !--- used for Easy VPN. This tunnel name is the one !--- specified on the remote side. 

tunnel-group mytunnel type remote-access
tunnel-group mytunnel general-attributes
 default-group-policy tunnel

!--- Defines the pre-shared key used for !--- IKE authentication for the dynamic tunnel.

tunnel-group mytunnel ipsec-attributes
 pre-shared-key *
prompt hostname context
Cryptochecksum:e148bf43d04906f5db41fc6f90c52d34
: end

Easy VPN 客户机 - ASA 5505 
ASA Version 7.2(2)
!
hostname ciscoasa
domain-name default.domain.invalid
enable password 8Ry2YjIyt7RRXU24 encrypted
names
!
interface Vlan1
 nameif outside
 security-level 0
 ip address 172.16.2.2 255.255.255.0
!
interface Vlan2
 nameif inside
 security-level 100
 ip address 192.168.3.1 255.255.255.0
!
interface Ethernet0/0
!
interface Ethernet0/1
 shutdown
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
 switchport access vlan 2


!--- Output Suppressed.


!

route outside 0.0.0.0 0.0.0.0 172.16.2.1 1


!--- Output Suppressed.



!--- Easy VPN Client Configuration ---! !--- Specify the IP address of the VPN server.

vpnclient server 10.1.1.1

!--- This example uses network extension mode.

vpnclient mode network-extension-mode

!--- Specify the group name and the pre-shared key.

vpnclient vpngroup mytunnel password ********

!--- Specify the authentication username and password.

vpnclient username cisco password ********

!--- In order to enable the device as hardware vpnclient, use this command.

vpnclient enable
!



!--- Output Suppressed.


Cryptochecksum:0458ce7a08e6b7f9417b17bc254eb4e2
: end

PIX 
PIX Version 8.0(2)
!
hostname pixfirewall
enable password 8Ry2YjIyt7RRXU24 encrypted
names
!
interface Ethernet0
 nameif outside
 security-level 0
 ip address 172.16.1.1 255.255.255.0
!
interface Ethernet1
 nameif inside
 security-level 100
 ip address 192.168.1.2 255.255.255.0
!
passwd 2KFQnbNIdI.2KYOU encrypted
ftp mode passive

!--- This access list (inside_nat0_outbound) is used with the nat zero command. !--- This prevents traffic which matches the access list from undergoing !--- network address translation (NAT). 

access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0
 192.168.2.0 255.255.255.0

!--- The traffic specified by this ACL is !--- traffic that is to be encrypted and !--- sent across the VPN tunnel. This ACL is intentionally !--- the same as (inside_nat0_outbound). !--- Two separate access lists must always be used in this configuration.

access-list outside_cryptomap_20 extended permit ip 192.168.1.0 255.255.255.0
 192.168.2.0 255.255.255.0

!--- NAT 0 prevents NAT for networks specified in the ACL inside_nat0_outbound. 

nat (inside) 0 access-list inside_nat0_outbound


!--- Output Suppressed.

route outside 0.0.0.0 0.0.0.0 172.16.1.2 1


!--- Output Suppressed.


!--- PHASE 2 CONFIGURATION ---! !--- The encryption types for Phase 2 are defined here. !--- Define the transform set for Phase 2. 


crypto ipsec transform-set myset esp-3des esp-sha-hmac


!--- Define which traffic can be sent to the IPsec peer.


crypto map outside_map 20 match address outside_cryptomap_20


!--- Sets the IPsec peer.


crypto map outside_map 20 set peer 10.1.1.1


!--- Sets the IPsec transform set "myset" !--- to be used with the crypto map entry "outside_map".


crypto map outside_map 20 set transform-set myset


!--- Specifies the interface to be used with !--- the settings defined in this configuration. 


crypto map outside_map interface outside

!--- PHASE 1 CONFIGURATION ---! !--- This configuration uses isakmp policy 10. !--- Policy 65535 is included in the config by default. !--- The configuration commands here define the Phase !--- 1 policy parameters that are used.


crypto isakmp enable outside
crypto isakmp policy 10
 authentication pre-share
 encryption 3des
 hash sha
 group 2
 lifetime 86400
crypto isakmp policy 65535
 authentication pre-share
 encryption 3des
 hash sha
 group 2
 lifetime 86400


!--- Output Suppressed. !--- In order to create and manage the database of connection-specific records !--- for ipsec-l2l—IPsec (LAN-to-LAN) tunnels, use the tunnel-group !--- command in global configuration mode. !--- For L2L connections the name of the tunnel group MUST be the IP !--- address of the IPsec peer. 


tunnel-group 10.1.1.1 type ipsec-l2l

!--- Enter the pre-shared-key in order to configure the authentication method.

tunnel-group 10.1.1.1 ipsec-attributes
 pre-shared-key *

prompt hostname context
Cryptochecksum:4a2c70f2102113315de795f13f25c2aa
: end

验证

本部分提供了可用于确认您的配置是否正常运行的信息。

命令输出解释程序（仅限注册用户）(OIT) 支持某些 show 命令。使用 OIT 可查看对 show 命令输出的分析。

  • show crypto isakmp sa - 显示对等体上的所有当前 IKE 安全关联 (SA)。

  • show crypto ipsec sa — 显示所有当前 SA。

本部分显示用于以下配置的示例验证配置：

HUB ASA 
ciscoasa #show crypto isakmp sa
 
   Active SA: 2
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 2

!--- Dynamic LAN-to-LAN tunnel establishment

1   IKE Peer: 172.16.2.2
    Type    : user            Role    : responder
    Rekey   : no              State   : AM_ACTIVE

!--- Static LAN-to-LAN tunnel establishment

2   IKE Peer: 172.16.1.1
    Type    : L2L             Role    : initiator
    Rekey   : no              State   : MM_ACTIVE





ciscoasa #show crypto ipsec sa
ciscoasa(config)#sh crypto ipsec sa
interface: outside
    Crypto map tag: outside_map, seq num: 20, local addr: 10.1.1.1

     
      access-list outside_cryptomap_20 permit ip 192.168.2.0 255.255.255.0
		 192.168.1.0 255.255.255.0
      local ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
      current_peer: 172.16.1.1

      #pkts encaps: 4, #pkts encrypt: 4, #pkts digest: 4
      #pkts decaps: 4, #pkts decrypt: 4, #pkts verify: 4
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 4, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0

      local crypto endpt.: 10.1.1.1, remote crypto endpt.: 172.16.1.1

      path mtu 1500, ipsec overhead 58, media mtu 1500
      current outbound spi: E4312E13

    inbound esp sas:
      spi: 0x9ABAC3DD (2595931101)
         transform: esp-3des esp-sha-hmac none
         in use settings ={L2L, Tunnel, }
         slot: 0, conn_id: 741376, crypto-map: outside_map
         sa timing: remaining key lifetime (kB/sec): (4274999/28783)
         IV size: 8 bytes
         replay detection support: Y
    outbound esp sas:
      spi: 0xE4312E13 (3828428307)
         transform: esp-3des esp-sha-hmac none
         in use settings ={L2L, Tunnel, }
         slot: 0, conn_id: 741376, crypto-map: outside_map
         sa timing: remaining key lifetime (kB/sec): (4274999/28783)
         IV size: 8 bytes
         replay detection support: Y

   Crypto map tag: ezvpn, seq num: 30, local addr: 10.1.1.1

     local ident (addr/mask/prot/port): (10.1.1.1/255.255.255.255/0/0)
      remote ident (addr/mask/prot/port): (172.16.2.2/255.255.255.255/0/0)
      current_peer: 172.16.2.2, username: cisco
      dynamic allocated peer ip: 0.0.0.0

      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
      #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0

      local crypto endpt.: 10.1.1.1, remote crypto endpt.: 172.16.2.2

      path mtu 1500, ipsec overhead 58, media mtu 1500
      current outbound spi: 2647B59C

    inbound esp sas:
      spi: 0x21685AF8 (560487160)
         transform: esp-3des esp-sha-hmac none
         in use settings ={RA, Tunnel, }
         slot: 0, conn_id: 737280, crypto-map: ezvpn
         sa timing: remaining key lifetime (sec): 28146
         IV size: 8 bytes
         replay detection support: Y
    outbound esp sas:
      spi: 0x2647B59C (642233756)
         transform: esp-3des esp-sha-hmac none
         in use settings ={RA, Tunnel, }
         slot: 0, conn_id: 737280, crypto-map: ezvpn
         sa timing: remaining key lifetime (sec): 28146
         IV size: 8 bytes
         replay detection support: Y

    Crypto map tag: ezvpn, seq num: 30, local addr: 10.1.1.1

      local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.3.0/255.255.255.0/0/0)
      current_peer: 172.16.2.2, username: cisco
      dynamic allocated peer ip: 0.0.0.0

      #pkts encaps: 5, #pkts encrypt: 5, #pkts digest: 5
      #pkts decaps: 5, #pkts decrypt: 5, #pkts verify: 5
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 5, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0

      local crypto endpt.: 10.1.1.1, remote crypto endpt.: 172.16.2.2

      path mtu 1500, ipsec overhead 58, media mtu 1500
      current outbound spi: 07997B21

    inbound esp sas:
      spi: 0xB5B6013D (3048603965)
         transform: esp-3des esp-sha-hmac none
         in use settings ={RA, Tunnel, }
         slot: 0, conn_id: 737280, crypto-map: ezvpn
         sa timing: remaining key lifetime (sec): 28145
         IV size: 8 bytes
         replay detection support: Y
    outbound esp sas:
      spi: 0x07997B21 (127499041)
         transform: esp-3des esp-sha-hmac none
         in use settings ={RA, Tunnel, }
         slot: 0, conn_id: 737280, crypto-map: ezvpn
         sa timing: remaining key lifetime (sec): 28145
         IV size: 8 bytes
         replay detection support: Y

    Crypto map tag: ezvpn, seq num: 30, local addr: 10.1.1.1

      local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
      remote ident (addr/mask/prot/port): (172.16.2.2/255.255.255.255/0/0)
      current_peer: 172.16.2.2, username: cisco
      dynamic allocated peer ip: 0.0.0.0

      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
      #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0

      local crypto endpt.: 10.1.1.1, remote crypto endpt.: 172.16.2.2

      path mtu 1500, ipsec overhead 58, media mtu 1500
      current outbound spi: 0F0B1A75

    inbound esp sas:
      spi: 0x68B0EA75 (1756424821)
         transform: esp-3des esp-sha-hmac none
         in use settings ={RA, Tunnel, }
         slot: 0, conn_id: 737280, crypto-map: ezvpn
         sa timing: remaining key lifetime (sec): 28143
         IV size: 8 bytes
         replay detection support: Y
    outbound esp sas:
      spi: 0x0F0B1A75 (252385909)
         transform: esp-3des esp-sha-hmac none
         in use settings ={RA, Tunnel, }
         slot: 0, conn_id: 737280, crypto-map: ezvpn
         sa timing: remaining key lifetime (sec): 28143
         IV size: 8 bytes
         replay detection support: Y

Easy VPN 客户机 ASA 5505 
ciscoasa(config)# sh crypto isakmp sa

   Active SA: 1
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1

1   IKE Peer: 10.1.1.1
    Type    : user            Role    : initiator
    Rekey   : no              State   : AM_ACTIVE



ciscoasa(config)# sh crypto ipsec sa
interface: outside
    Crypto map tag: _vpnc_cm, seq num: 10, local addr: 172.16.2.2

      access-list _vpnc_acl permit ip host 172.16.2.2 host 10.1.1.1
      local ident (addr/mask/prot/port): (172.16.2.2/255.255.255.255/0/0)
      remote ident (addr/mask/prot/port): (10.1.1.1/255.255.255.255/0/0)
      current_peer: 10.1.1.1, username: 10.1.1.1
      dynamic allocated peer ip: 0.0.0.0

      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
      #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0

      local crypto endpt.: 172.16.2.2, remote crypto endpt.: 10.1.1.1

      path mtu 1500, ipsec overhead 58, media mtu 1500
      current outbound spi: 21685AF8

    inbound esp sas:
      spi: 0x2647B59C (642233756)
         transform: esp-3des esp-sha-hmac none
         in use settings ={RA, Tunnel, }
         slot: 0, conn_id: 178, crypto-map: _vpnc_cm
         sa timing: remaining key lifetime (sec): 28298
         IV size: 8 bytes
         replay detection support: Y
    outbound esp sas:
      spi: 0x21685AF8 (560487160)
         transform: esp-3des esp-sha-hmac none
         in use settings ={RA, Tunnel, }
         slot: 0, conn_id: 178, crypto-map: _vpnc_cm
         sa timing: remaining key lifetime (sec): 28298
         IV size: 8 bytes
         replay detection support: Y

    Crypto map tag: _vpnc_cm, seq num: 10, local addr: 172.16.2.2

      access-list _vpnc_acl permit ip host 172.16.2.2 any
      local ident (addr/mask/prot/port): (172.16.2.2/255.255.255.255/0/0)
      remote ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
      current_peer: 10.1.1.1, username: 10.1.1.1
      dynamic allocated peer ip: 0.0.0.0

      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
      #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0

      local crypto endpt.: 172.16.2.2, remote crypto endpt.: 10.1.1.1

      path mtu 1500, ipsec overhead 58, media mtu 1500
      current outbound spi: 68B0EA75

    inbound esp sas:
      spi: 0x0F0B1A75 (252385909)
         transform: esp-3des esp-sha-hmac none
         in use settings ={RA, Tunnel, }
         slot: 0, conn_id: 178, crypto-map: _vpnc_cm
         sa timing: remaining key lifetime (sec): 28298
         IV size: 8 bytes
         replay detection support: Y
    outbound esp sas:
      spi: 0x68B0EA75 (1756424821)
         transform: esp-3des esp-sha-hmac none
         in use settings ={RA, Tunnel, }
         slot: 0, conn_id: 178, crypto-map: _vpnc_cm
         sa timing: remaining key lifetime (sec): 28298
         IV size: 8 bytes
         replay detection support: Y

    Crypto map tag: _vpnc_cm, seq num: 10, local addr: 172.16.2.2

      access-list _vpnc_acl permit ip 192.168.3.0 255.255.255.0 any
      local ident (addr/mask/prot/port): (192.168.3.0/255.255.255.0/0/0)
      remote ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
      current_peer: 10.1.1.1, username: 10.1.1.1
      dynamic allocated peer ip: 0.0.0.0

      #pkts encaps: 5, #pkts encrypt: 5, #pkts digest: 5
      #pkts decaps: 5, #pkts decrypt: 5, #pkts verify: 5
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0

      local crypto endpt.: 172.16.2.2, remote crypto endpt.: 10.1.1.1

      path mtu 1500, ipsec overhead 58, media mtu 1500
      current outbound spi: B5B6013D

    inbound esp sas:
      spi: 0x07997B21 (127499041)
         transform: esp-3des esp-sha-hmac none
         in use settings ={RA, Tunnel, }
         slot: 0, conn_id: 178, crypto-map: _vpnc_cm
         sa timing: remaining key lifetime (sec): 28294
         IV size: 8 bytes
         replay detection support: Y
    outbound esp sas:
      spi: 0xB5B6013D (3048603965)
         transform: esp-3des esp-sha-hmac none
         in use settings ={RA, Tunnel, }
         slot: 0, conn_id: 178, crypto-map: _vpnc_cm
         sa timing: remaining key lifetime (sec): 28294
         IV size: 8 bytes
         replay detection support: Y

PIX 
pixfirewall(config)# sh crypto isakmp sa

   Active SA: 1
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1

1   IKE Peer: 10.1.1.1
    Type    : L2L             Role    : responder
    Rekey   : no              State   : MM_ACTIVE



pixfirewall(config)# sh crypto ipsec sa
interface: outside
    Crypto map tag: outside_map, seq num: 20, local addr: 172.16.1.1

     access-list outside_cryptomap_20 permit ip 192.168.1.0 255.255.255.0
	    192.168.2.0 255.255.255.0
      local ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0)
      current_peer: 10.1.1.1

      #pkts encaps: 4, #pkts encrypt: 4, #pkts digest: 4
      #pkts decaps: 4, #pkts decrypt: 4, #pkts verify: 4
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0

      local crypto endpt.: 172.16.1.1, remote crypto endpt.: 10.1.1.1

      path mtu 1500, ipsec overhead 58, media mtu 1500
      current outbound spi: 9ABAC3DD

    inbound esp sas:
      spi: 0xE4312E13 (3828428307)
         transform: esp-3des esp-sha-hmac none
         in use settings ={L2L, Tunnel, }
         slot: 0, conn_id: 12288, crypto-map: outside_map
         sa timing: remaining key lifetime (kB/sec): (3824999/28628)
         IV size: 8 bytes
         replay detection support: Y
    outbound esp sas:
      spi: 0x9ABAC3DD (2595931101)
         transform: esp-3des esp-sha-hmac none
         in use settings ={L2L, Tunnel, }
         slot: 0, conn_id: 12288, crypto-map: outside_map
         sa timing: remaining key lifetime (kB/sec): (3824999/28628)
         IV size: 8 bytes
         replay detection support: Y

故障排除

本部分提供了可用于对配置进行故障排除的信息。

故障排除命令

命令输出解释程序工具（仅限注册用户）支持某些 show 命令，使用此工具可以查看对 show 命令输出的分析。

注意：在发出debug命令之前，请参阅有关Debug命令的重要信息。

在配置模式下发出 PIX 命令：

  • clear crypto isakmp sa — 清除第 1 阶段 SA

  • clear crypto ipsec sa — 清除第 2 阶段 SA

用于 VPN 隧道的 debug 命令：

  • debug crypto isakmp sa — 调试 ISAKMP SA 协商

  • debug crypto ipsec sa — 调试 IPSec SA 协商

相关信息

修订历史记录

版本 发布日期 备注
1.0
30-Sep-2008
初始版本

此文档是否有帮助?

Feedback反馈

联系我们

本文档适用于以下产品