通过TL1命令从本地节点登录远程节点

简介

本文档介绍通过TL1从本地节点登录可到达远程节点的方法。

通过TL1命令从本地节点登录远程节点

在尝试从相邻可到达节点登录远程节点时，如果思科传输控制器(CTC)不工作，则保留TL1方法。

此方法描述如何从本地登录节点登录远程节点，步骤如下：

步骤1.登录到节点并检查远程节点是否可通过任何通道到达，例如。(DCC/GCC/OSI)或通过ping直接访问。

-> acNodes
========================== AlrmC Nodes =================================
ind Val NodeName          IP Addr      Cri Maj Min N-A N-R Vwire ProdField VirtWrProdNm VirtWireProdEnum MsgVer
--- --- -------------------- ----------------  --- --- --- --- --- -----
  0 Yes 206                  10.105.142.206      3   0   2   8   1  xxxx ONS15454  1 400
  1 Yes WXC-207              10.105.142.207      0   1   5   6   0  xxxx ONS15454  1 400
  2 Yes 197                  10.105.142.197      3   2  11  11   5  xxxx ONS15454  1 400

步骤2.使用此语法通过TL1登录本地节点。

语法:

ACT-USER:[<TID>]:<uid>:<CTAG>::<pid>;

  ACT-USER::CISCO15:123::******;

   206 2000-12-15 23:43:21
M  123 COMPLD
   "CISCO15:2000-12-15 23-42-43,2000-12-15 23-15-04,0"
;

   206 2000-12-15 23:43:21
A  0 REPT EVT SESSION
   "206:NO,"
   /* TL1 Agent Copyright (c) 1999-2007 Cisco Systems, Inc.

WARNING
This system is restricted to authorized users for business purposes. Unauthorized
access is a violation of the law. This service may be monitored for administrative
and security reasons. By proceeding, you consent to this monitoring.

      User CISCO15 logged in from 64.103.228.115 */
;

      User CISCO15 logged in from 10.105.142.206 */
;RTRV-ALM-ALL:::123;

   206 2000-12-15 23:47:04
M  123 COMPLD
   "SLOT-11,EQPT:MN,EQPT,NSA,12-04,03-26-24,NEND,NA:\"Equipment Failure\",TCC"
   "LINEWL-17-4-RX-1530.33,OCH:CR,LOS-P,SA,12-09,02-55-16,NEND,NA:\"Incoming Payload Signal Absent\",40-SMR1-C"
   "LINEWL-17-4-RX-1531.90,OCH:CR,LOS-P,SA,12-09,02-57-20,NEND,NA:\"Incoming Payload Signal Absent\",40-SMR1-C"
   "LINE-17-5-TX,OTS:CR,OPWR-LFAIL,SA,12-09,02-55-19,NEND,NA:\"Optical Power Failure Low\",40-SMR1-C"
   "LINE-17-1-TX,OTS:MN,APC-OUT-OF-RANGE,NSA,12-15,22-55-33,NEND,NA:\"APC Cannot Set Value Due To Range Limits\",40-SMR1-C"

步骤3.根据语法，更改要登录的远程节点的TID和ACT-USER登录。对于其他命令，您也需要使用TID值，即远程节点名称。

> ACT-USER:WXC-207:CISCO15:123::******;

   WXC-207 2004-06-03 18:50:20
M  123 COMPLD
   "CISCO15:2004-06-03 18-23-24,2004-06-03 16-35-48,0"
;
> 

   WXC-207 2004-06-03 18:50:20
A  0 REPT EVT SESSION
   "WXC-207:NO,"
   /* TL1 Agent Copyright (c) 1999-2007 Cisco Systems, Inc.

WARNING
This system is restricted to authorized users for business purposes. Unauthorized
access is a violation of the law. This service may be monitored for administrative
and security reasons. By proceeding, you consent to this monitoring.

      User CISCO15 logged in from 10.105.142.206 */

对于示例中所示的其他命令，您需要输入相应的TID值，即节点名称WXC-207:

> RTRV-ALM-ALL:WXC-207::123;

   WXC-207 2004-06-03 18:50:54
M  123 COMPLD
   "SLOT-11,EQPT:MN,PROTNA,NSA,05-21,21-55-10,NEND,NA:\"Protection Unit Not Available\",TCC"
   "BITS-1,BITS:MN,LOS,NSA,05-21,21-55-25,NEND,RCV:\"Loss Of Signal\","
   "BITS-2,BITS:MN,LOS,NSA,05-21,21-55-25,NEND,RCV:\"Loss Of Signal\","
   "SYNC-NE,SYNCN:MJ,SYNCPRI,SA,05-21,21-55-25,NEND,NA:\"Primary Synchronization Reference Failure\","
   "SYNC-NE,SYNCN:MN,SYNCSEC,NSA,05-21,21-55-25,NEND,NA:\"Secondary Synchronization Reference Failure\","
   "PWR-A,EQPT:MN,BAT-FAIL,NSA,05-21,21-55-18,NEND,NA:\"Battery Failure\","
;

即使您登录到远程节点，也可以在任何其他连接的节点中导航，更改远程节点的TID，并将其保留为空白，作为本地节点的TID。