本文档介绍数字用户线路(DSL)接口上的参考带宽的概念。还讨论了DSL控制器和接口下显示的值的差异。
作者:Richika Jain,思科TAC工程师。
本文档没有任何特定的要求。
本文档中的信息基于支持DSL连接的Cisco路由器,例如接入端的Very-high-bit-rate digital subscriber line(VDSL)、Symmetric high-speed digital subscriber line(SHDSL)和Asymmetric digital subscriber line(ADSL)。
本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始(默认)配置。如果您的网络处于活动状态,请确保您了解所有命令的潜在影响。
与其他介质不同,在DSL中,上行和下行带宽有所不同。
例如,对于E1,上游为2.048 mb,下游为2.048 mb,当路由器计算负载和重载时,它会将上游和下游的2.048 mb分作为一分,并以比例255对其进行规范化并显示。因此,如果接口下的输入速率是2048000,您会看到255/255的重新加载。
现在,对于DSL,路由器需要参考带宽值才能进行相同的计算。但这里有两个带宽,上行和下行带宽。接口下显示的带宽是上行带宽。
Ethernet0/0/0 is up, line protocol is up
Hardware is VDSL_ETHERNET, address is 3033.199e.1948
MTU 1500 bytes, BW 9998 Kbit/sec, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 05:00:00
Last input 3w6d, output 00:00:00, output hang never
Last clearing of "show interface" counters 06:15:00
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/1024 (size/max)
5 minute input rate 2850000 bits/sec, 420 packets/sec
5 minute output rate 5749000 bits/sec, 1747 packets/sec
3887957 packets input, 3183892807 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
1573 packets output, 100231 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
之所以选择上行带宽作为参考带宽,是因为大部分时间在输出方向使用QoS策略,并且它需要准确的参考带宽。
在VDSL控制器的输出中,有两种速度值:上行和下行可达到的速率和速度。速度是线路被ISP训练时所依据的值,可达到的速率是VDSL电路的最大速度。
n3-ne-r-hi-435773-01#sh controller vdsl 0/1/0 | i Speed|Attainable Attainable Rate: 40440 kbits/s 3280 kbits/s Speed (kbps): 0 25087 0 3192
VDSL控制器的完整输出:
Router#show controller vdsl 0/1/0
Controller VDSL 0/1/0 is UP
Daemon Status: Up
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'BDCM'
Chip Vendor Specific: 0x0000 0xA1AA
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FOC15163V2Q 2911/K9 15.5(1)T
Serial Number Far:
Modem Version Near: 15.5(1)T
Modem Version Far: 0xa1aa
Modem Status: TC Sync (Showtime!)
DSL Config Mode: AUTO
Trained Mode: G.993.2 (VDSL2) Profile 17a
TC Mode: PTM
Selftest Result: 0x00
DELT configuration: disabled
DELT state: not running
Full inits: 1
Failed full inits: 0
Short inits: 0
Failed short inits: 0
Firmware Source File Name
-------- ------ ----------
VDSL embedded VDSL_LINUX_DEV_01212008
Modem FW Version: 130205_1433-4.02L.03.B2pvC035j.d23j
Modem PHY Version: B2pvC035j.d23j
Trellis: ON ON
SRA: disabled disabled
SRA count: 0 0
Bit swap: enabled enabled
Bit swap count: 0 0
Line Attenuation: 0.0 dB 0.0 dB
Signal Attenuation: 0.0 dB 0.0 dB
Noise Margin: 11.1 dB 6.0 dB
Attainable Rate: 40440 kbits/s 3280 kbits/s
Actual Power: 14.5 dBm 4.9 dBm
Per Band Status: D1 D2 D3 U0 U1 U2 U3
Line Attenuation(dB): 20.0 48.3 73.7 9.4 37.9 56.2 N/A
Signal Attenuation(dB): 20.0 48.3 N/A 10.2 36.2 53.3 N/A
Noise Margin(dB): 10.9 11.3 N/A 5.9 6.0 6.0 N/A
Total FECC: 97252 0
Total ES: 7 0
Total SES: 0 0
Total LOSS: 0 0
Total UAS: 24 24
Total LPRS: 0 0
Total LOFS: 0 0
Total LOLS: 0 0
!--- DSL trained speed can be found below
DSChannel1 DSChannel0 US Channel1 US Channel0
Speed (kbps): 0 25087 0 3192
SRA Previous Speed: 0 0 0 0
Previous Speed: 0 0 0 0
Reed-Solomon EC: 0 97252 0 0
CRC Errors: 0 15 0 0
Header Errors: 0 62 0 0
Interleave (ms): 0.00 8.00 0.00 8.00
Actual INP: 0.00 3.01 0.00 2.00
Training Log : Stopped
Training Log Filename : flash:vdsllog.bin
现在,对于txload和rxload计算,它使用相同的参考带宽,即Upstream Bandth。因此,当输入流量速率(例如998000)为255/255时,您会看到rxload,而当输入速率大于20 mb和30 mb时,它会显示rxload 255/255。因此,显示的rxload值在默认参考带宽下始终不准确。但是,它不会对您接收的实际带宽/速度或吞吐量有任何影响。
如果要为QoS目的更改它,可以在接口下使用bandwidth命令进行更改。但是,无论bandwidth命令设置为什么值,接口都不会更改其传输速度。
| 版本 | 发布日期 | 备注 |
|---|---|---|
1.0 |
17-Aug-2017
|
初始版本 |