Voice/Fax (EVM-HD)功能的高密度模拟(FXS/DID/FXO)和数字(BRI)分机模块提供一个更高密度的集成模拟/数字语音接口。EVM-HD-8FXS/DID基线板网络模块提供八个局外交换站(FXS)或直接拨入(DID)端口。此网络模块访问数字信号在主板的信号处理器(DSP)模块,而不是使用内置DSP。您能通过任意组合插入增加端口密度在两可选扩展模块:
PVDM2 DSP模块使用与EVM-HD-8FXS/DID基线板和其扩展模块的组合。PVDM2模块分开是可用的和安装在DSP模块插槽查找在路由器机箱里面。
在尝试此配置前,请保证您符合这些要求:
本文档中的信息根据以下:
注意:对非 Cisco 产品或服务的介绍仅作参考之用,请勿视作担保或推荐。
有关文档规则的详细信息,请参阅 Cisco 技术提示规则。
此部分为Voice/Fax提供关于高密度模拟和数字分机模块的背景信息。
Voice/Fax的高密度模拟和数字分机模块支持以下:
FXS接口连接路由器或接入服务器到终端用户设备例如电话、传真机或者调制解调器。FXS接口用品敲响,电压和拨号音到站点。FXO接口使用中继或者连接线,连接对PSTN CO或对PBX。此接口有价值驻地外的站点应用程序的。
FXO和FXS接口由两个访问信令方法之一指示挂机或摘机状况和电话线捕捉:回路开始或接地启动。访问信令种类取决于服务类型从CO;标准的家庭电话线使用回路开始,但是企业电话能使用接地启动线路。
回路开始普通访问信令技术。拿起听筒(电话摘机)时,此操作会断开从电话公司 CO 获取电流的电路,并指示状态发生变化,这会向 CO 发送提供拨号声音的信号。呼入呼叫从CO发信号到话筒由一个标准的开/关模式信号,造成电话敲响。
对于相关的信息对硬件连接,参考在“涉及文档”部分的硬件列出的文档。
通过被数字化的脉冲编码调制(PCM)语音的语音系统总是依靠在被认为标准的比特数据流嵌入的时钟信号。此技术允许连接的设备从比特流恢复时钟信号,然后使用此恢复时钟信号保证在不同的信道的数据保持同一个时钟关系用其他信道。
如果一个普通的时钟源没有使用在设备之间,在比特流的二进制值可能误译,因为设备不是时候采样信号。为例,如果接收设备的本地时间比发送设备的定时使用一个轻微更短的时间,八连续二进制1字符串可能解释作为九连续1。如果此数据然后被再发出到使用变化的定时参考的进一步下行设备,错误可以被配制。当您确保,在网络使用的每个设备同一时钟信号,流量的完整性可以是委托。
如果在设备之间的定时没有维护,叫作时钟疏漏的情况能发生。时钟疏漏是位块的重复或删除同步比特流的由于在读的一个差异并且写入速率在缓冲区。
滑动由设备缓冲存储器(或其他机制的)无法造成适应在流入和流出的信号的相位或频率的之间区别,在流出的信号的定时从那流入的信号处没有派生。
BRI接口发送呼叫帧的流量内部的重复的比特模式。每帧是位固定数量的。这意味着接收设备什么时候正确地知道通过计数位期待帧的末端,当他们到达。所以,如果在发送和接收设备之间的定时不是相同的,接收设备可能不是时候采样比特流,造成返回的不正确的值。
即使您能配置Cisco IOS软件控制在这些设备的时钟频率,默认时钟模式有效是自由运行,含义从接口的已接收时钟信号没有连接对路由器的背板并且使用在路由器的其余和其接口之间的内部同步。路由器使用其内时钟源通过在背板和其他接口间的流量。
对于数据应用,因为数据包在内存缓冲和然后复制到目的地接口的传输缓冲区,通常来源此的内部时钟不提出一问题。数据包读和文字对内存的有效取消对所有时钟同步的需要在端口之间。
数字语音端口存在另一个问题。除非配置, Cisco IOS软件使用背板(或内部)时钟频率控制数据读和文字到DSP。如果 PCM 流在数字语音端口上传入,则该 PCM 流将使用接收比特流的外部计时。然而,此比特流不一定是使用参考和一样路由器背板,含义DSP能曲解自控制器进来的数据。
此时钟频率不匹配在路由器的BRI控制器被看到作为时钟疏漏--路由器使用其内时钟源传送流量接口,但是进来到接口的流量使用一个完全不同的时钟参考。最终,在时钟关系的差异传输之间和接收信号变得很极大控制器注册在收到的帧的滑动。
要消除问题,您必须通过Cisco IOS配置命令更改默认时钟频率行为。适当地设置时钟频率命令是十分重要的。
即使以下命令可选,我们强烈建议您进入他们作为您的配置一部分您保证适当网络时钟同步:
network-clock-participate [slot slot-number]
network-clock-select priority {bri | t1 | e1} slot/port
network-clock-participate命令允许路由器通过指定插槽使用从线路的时钟和同步内置时钟到同一参考。
如果多个VWIC安装,您必须重复每个安装的卡的命令。使用show network clocks命令,系统时钟可以被确认。
本部分提供有关如何配置本文档所述功能的信息。
注意:要查找本文档所用命令的其他信息,请使用命令查找工具(仅限注册用户)。
本文在此图表中使用表示的网络设置
本文档使用此处所示的配置:
作为模拟DID语音网关使用的EVM-HD-8FXS/DID连接对PSTN
show voice port输出
基本语音模块(8FXS/DID)和一4BRI扩展模块
基本语音模块(8FXS/DID)和两4BRI扩展模块
步骤 1 |
作为模拟DID语音网关使用的EVM-HD-8FXS/DID连接对PSTN ! ! voice-port 2/0/0 signal did immediate ! voice-port 2/0/1 ! signal did wink-start ! Sets max time to wait for wink signaling after outgoing seizure is sent. ! Default is 550 ms. timing wait-wink 550 ! ! Sets the maximum time to wait before sending wink signal after an ! incoming seizure is detected. Default is 200 ms. timing wink-wait 200 ! ! Sets duration of wink-start signal. Default is 200 ms. timing wink-duration 200 ! voice-port 2/0/2 ! signal did delay-dial ! ! Sets duration of the delay signal. Default is 200 ms. timing delay-duration 200 ! ! Sets delay interval after incoming seizure is detected. ! Default is 300 ms. timing delay-start 300 ! |
步骤 2 |
show voice port输出 Router# show voice port 2/0/1
Foreign Exchange Station with Direct Inward Dialing (FXS-DID) 2/0/0 Slot is 2, Sub-unit
is 0, Port is 0
Type of VoicePort is DID-IN
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Playout-delay Mode is set to default
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 200 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Ringing Time Out is set to 180 s
Companding Type is u-law
Region Tone is set for US
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Wait Release Time Out is 30 s
Station name None, Station number None
Voice card specific Info Follows:
Signal Type is wink-start
Dial Type is dtmf
In Seizure is inactive
Out Seizure is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Clear Wait Duration Timing is set to 400 ms
Wink Wait Duration Timing is set to 200 ms
Wait Wink Duration Timing is set to 550 ms
Wink Duration Timing is set to 200 ms
Delay Start Timing is set to 300 ms
Delay Duration Timing is set to 2000 ms
Dial Pulse Min. Delay is set to 140 ms
Percent Break of Pulse is 60 percent
Auto Cut-through is disabled
Dialout Delay for immediate start is 300 ms |
步骤 3 |
基本语音模块(8FXS/DID)和一4BRI扩展模块 Router1# show running-config
isdn switch-type basic-dms100
!
voice-card 0
no dspfarm
!
interface GigabitEthernet0/0
ip address 10.0.0.0 255.255.0.0
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface BRI2/0
no ip address
isdn switch-type basic-dms100
isdn incoming-voice voice
!
interface BRI2/1
no ip address
!
interface BRI2/2
no ip address
!
interface BRI2/3
no ip address
!
voice-port 2/0/0
signal did wink-start
!
voice-port 2/0/1
signal did wink-start
!
voice-port 2/0/2
caller-id enable
!
voice-port 2/0/3
caller-id enable
!
voice-port 2/0/4
caller-id enable
!
voice-port 2/0/5
caller-id enable
!
voice-port 2/0/6
caller-id enable
!
voice-port 2/0/7
caller-id enable
!
voice-port 2/0/8
!
voice-port 2/0/9
!
voice-port 2/0/10
!
voice-port 2/0/11
!
voice-port 2/0/17
caller-id enable
signal groundStart
!
voice-port 2/0/18
caller-id enable
!
voice-port 2/0/19
caller-id enable
!
dial-peer voice 1 pots
destination-pattern 202
port 2/0/2
!
dial-peer voice 2 pots
destination-pattern 203
port 2/0/3
!
dial-peer voice 3 pots
destination-pattern 204
port 2/0/4
!
dial-peer voice 4 pots
destination-pattern 205
port 2/0/5
!
dial-peer voice 5 pots
destination-pattern 206
port 2/0/6
!
dial-peer voice 6 pots
destination-pattern 207
port 2/0/7
!
end |
步骤 4 |
基本语音模块(8FXS/DID)和两4BRI扩展模块 注意:BRI接口是从BRI 2/0到BRI 2/7,但是那些BRI的语音端口是从2/0/8到2/0/11和2/0/16到2/0/19 version 12.3 network-clock-participate slot 2 network-clock-select 1 BRI2/2 network-clock-select 2 BRI2/3 network-clock-select 3 BRI2/4 network-clock-select 4 BRI2/5 network-clock-select 5 BRI2/6 network-clock-select 6 BRI2/7 ! isdn switch-type basic-net3 voice-card 0 no dspfarm ! interface BRI2/0 no ip address isdn switch-type basic-net3 isdn protocol-emulate network isdn layer1-emulate network isdn incoming-voice voice isdn skipsend-idverify ! interface BRI2/1 no ip address isdn switch-type basic-net3 isdn protocol-emulate network isdn layer1-emulate network isdn incoming-voice voice isdn skipsend-idverify ! interface BRI2/2 no ip address isdn switch-type basic-net3 isdn incoming-voice voice ! interface BRI2/3 no ip address isdn switch-type basic-net3 isdn incoming-voice voice ! interface BRI2/4 no ip address isdn switch-type basic-net3 isdn incoming-voice voice ! interface BRI2/5 no ip address isdn switch-type basic-net3 isdn incoming-voice voice ! interface BRI2/6 no ip address isdn switch-type basic-net3 isdn incoming-voice voice ! interface BRI2/7 no ip address isdn switch-type basic-net3 isdn incoming-voice voice ! voice-port 2/0/0 cptone IT ! voice-port 2/0/1 cptone IT ! voice-port 2/0/2 cptone IT ! voice-port 2/0/3 cptone IT ! voice-port 2/0/4 cptone IT ! voice-port 2/0/5 cptone IT ! voice-port 2/0/6 cptone IT ! voice-port 2/0/7 cptone IT ! voice-port 2/0/8 cptone IT ! voice-port 2/0/9 cptone IT ! voice-port 2/0/10 cptone IT ! voice-port 2/0/11 cptone IT ! voice-port 2/0/16 cptone IT ! voice-port 2/0/17 cptone IT ! voice-port 2/0/18 cptone IT ! voice-port 2/0/19 cptone IT ! dial-peer voice 200 pots destination-pattern 200 port 2/0/0 ! dial-peer voice 201 pots destination-pattern 201 port 2/0/1 ! dial-peer voice 202 pots destination-pattern 202 port 2/0/2 ! dial-peer voice 203 pots destination-pattern 203 port 2/0/3 ! dial-peer voice 204 pots destination-pattern 204 port 2/0/4 ! dial-peer voice 205 pots destination-pattern 205 port 2/0/5 ! dial-peer voice 206 pots destination-pattern 206 port 2/0/6 ! dial-peer voice 207 pots destination-pattern 207 port 2/0/7 ! end |
当前没有可用于此配置的验证过程。
本部分提供的信息可用于对配置进行故障排除。
在一些少见的实例,如果安装EM-HDA-3FXS/4FXO或EM-HDA-6FXO并且配置Groundstart信令的语音端口,您也许有连接一些呼出呼叫的困难。问题与FXO地面启动语音端口失败关连检测提示地面确认,造成一个不成功呼叫建立。
关于此问题的更多信息,参考排除故障模拟FXO地面启动呼出失败。