A Cisco traduziu este documento com a ajuda de tecnologias de tradução automática e humana para oferecer conteúdo de suporte aos seus usuários no seu próprio idioma, independentemente da localização. Observe que mesmo a melhor tradução automática não será tão precisa quanto as realizadas por um tradutor profissional. A Cisco Systems, Inc. não se responsabiliza pela precisão destas traduções e recomenda que o documento original em inglês (link fornecido) seja sempre consultado.
Este documento descreve alguns pontas e truques rápidos que podem aumentar a experiência do Troubleshooting com NX-OS.
Encantar suportes para o decimal Hexa, dezembro para o decimal
NX-OS# dec 0x89
137
NX-OS# hex 137
0x89
O CLI representa a interface da linha de comando
N7k-LabSW# show clock ; show switchname ; show license host-id
19:10:59.016 UTC Mon Apr 04 2016
N7k-LabSW
License hostid: VDH=TBM14354170
# trabalha para a configuração demasiado:
N7k-LabSW# conf t ; hostname N7k-LabSW-DEFAULT ; end
Enter configuration commands, one per line. End with CNTL/Z.
N7k-LabSW-DEFAULT#
# tempo tomou para que um CLI termine:
N7k-LabSW# show clock ; show run | ex .* ; show clock
07:56:08.709 UTC Tue Apr 05 2016
07:56:08.834 UTC Tue Apr 05 2016
N7k-LabSW# show cli variables
VSH Variable List (* = session vars)
-----------------
SWITCHNAME="N7k-LabSW"
TIMESTAMP="2016-04-05-08.34.18"
N7k-LabSW# tac-pac bootflash:$(SWITCHNAME)-$(TIMESTAMP)-show-tech-all.gz
N7k-LabSW# dir bootflash: | i show-tech-all
15091722 Apr 05 08:41:27 2016 N7k-LabSW-2016-04-05-08.35.57-show-tech-all.gz
Igualmente pode criar suas próprias variáveis:
1) Evite intervalos de sessão terminal:
N7k-LabSW# show terminal | i Timeout
Session Timeout: 30 minutes
N7k-LabSW# terminal session-timeout ?
<0-525600> Enter timeout in minutes, 0 to disable
N7k-LabSW# terminal session-timeout 0
N7k-LabSW# show terminal | i Timeout
Session Timeout: 0 minutes
2) Ajuste a largura/comprimento do terminal de exibição:
Vem acessível quando você não quer a saída quebrar a uma nova linha para saídas longas da largura
N7k-LabSW# show terminal | i Width
Length: 25 lines, Width: 98 columns
N7k-LabSW# terminal width 300
N7k-LabSW# show terminal | i Width
Length: 25 lines, Width: 300 columns
N7k-LabSW# show clock ; sleep 10 ; show clock
19:27:07.435 UTC Mon Apr 04 2016
19:27:17.445 UTC Mon Apr 04 2016
O VRF representa o roteamento virtual e a transmissão
Execute CLI para um VRF específico sem adicionar o <> VRF todas as vezes ao comando:
N7k-LabSW# routing-context vrf management
N7k-LabSW%management# sh ip route
IP Route Table for VRF "management"
'*' denotes best ucast next-hop
'**' denotes best mcast next-hop
'[x/y]' denotes [preference/metric]
'%<string>' in via output denotes VRF <string>
0.0.0.0/0, ubest/mbest: 1/0
*via 10.48.61.129, [1/0], 1w4d, static
10.48.61.128/26, ubest/mbest: 1/0, attached
*via 10.48.61.150, mgmt0, [0/0], 1w4d, direct
10.48.61.150/32, ubest/mbest: 1/0, attached
*via 10.48.61.150, mgmt0, [0/0], 1w4d, local
N7k-LabSW%management#
N7k-LabSW%management# routing-context vrf default
N7k-LabSW# sh ip route
IP Route Table for VRF "default"
'*' denotes best ucast next-hop
'**' denotes best mcast next-hop
'[x/y]' denotes [preference/metric]
'%<string>' in via output denotes VRF <string>
O VDC representa o contexto do dispositivo virtual
O LC representa a placa de linha
N7K representa o nexo 7000
Anexado uma vez ao LC, os CLI são executados com respeito ao padrão VDC, ou às necessidades especificar VDC # para o comando relacionado.
Em lugar de você pode executar os CLI em VDC # espaço apenas como o contexto de roteamento.
Exemplo:
N7k-LabSW# attach module 4
Attaching to module 4 ...
To exit type 'exit', to abort type '$.'
module-4# show hardware mac address-table
FE | Valid| PI| BD | MAC | Index| Stat| SW | Modi| Age| Tmr| GM| Sec| TR| NT| RM| RMA| Cap| Fld|Always| PV | RD| NN| UC|PI_E8| VIF | SWID| SSWID| LID
| | | | | | ic | | fied|Byte| Sel| | ure| AP| FY| | |TURE| | Learn| | | | | | | | |
---+------+---+------+---------------+-------+-----+-----+-----+----+----+---+----+---+---+---+----+----+----+------|----|---|---|---|-----|-----|-----|------|-------
4 1 1 2 0023.ac66.1dc1 0x010c7 1 0x000 0 0 0 1 0 0 0 0 0 0 0 0 0x00 0 0 0 0 0x000 0x000 0x000 0x010c7
5 1 1 2 0023.ac66.1dc1 0x010c7 1 0x000 0 0 0 1 0 0 0 0 0 0 0 0 0x00 0 0 0 0 0x000 0x000 0x000 0x010c7
Command outputs from Default VDC are pulled here
module-4# vdc 6 >>>>>>> switches LC to pull this VDC specific outputs only
module-4# show hardware mac address-table
FE | Valid| PI| BD | MAC | Index| Stat| SW | Modi| Age| Tmr| GM| Sec| TR| NT| RM| RMA| Cap| Fld|Always| PV | RD| NN| UC|PI_E8| VIF | SWID| SSWID| LID
| | | | | | ic | | fied|Byte| Sel| | ure| AP| FY| | |TURE| | Learn| | | | | | | | |
---+------+---+------+---------------+-------+-----+-----+-----+----+----+---+----+---+---+---+----+----+----+------|----|---|---|---|-----|-----|-----|------|-------
0 1 1 92 0023.ac66.1dc6 0x010c7 1 0x000 0 0 0 1 0 0 0 0 0 0 0 0 0x00 0 0 0 0 0x000 0x000 0x000 0x010c7
0 1 0 91 0019.3074.9c02 0x00414 0 0x009 0 118 2 0 0 0 0 0 0 0 0 0 0x00 1 0 1 0 0x000 0x000 0x000 0x00414
N5600-Lab# load dplugg
Loading plugin version 7.1(1)N1(1)
###############################################################
Warning: debug-plugin is for engineering internal use only!
For security reason, plugin image has been deleted.
###############################################################
Successfully loaded debug-plugin!!!
Linux(debug)# vsh >>>>> Moves back to NX-OS prompt
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2015, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
N5600-Lab# show clock
20:20:07.468 UTC Mon Apr 04 2016
N5600-Lab# exit >>>>> Moves back to Linux prompt
Linux(debug)#
Linux(debug)# clock
Mon Apr 4 20:20:13 2016 -0.282195 seconds UTC
NOTE: "Debug Plugin" should only be used in presence of Cisco TAC and is not available for customer use.
Please do not modify any setting unless guided by Cisco TAC.
Alternativamente NX-OS CLI podia ser executado diretamente de debuga de encaixe:
Linux(debug)# vsh -c "show switchname"
N5600-Lab
Linux(debug)# vsh -c "show module"
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ---------------------- -----------
1 52 Nexus 56128P Supervisor N5K-C56128P-SUP active *
Mod Sw Hw World-Wide-Name(s) (WWN)
--- -------------- ------ ---------------------------------------------------
1 7.1(1)N1(1) 1.1 --
<snipped>
VSH representa o shell virtual
NEXUS-LABSWICTH# echo "hostname LAB" | vsh
LAB#
Mon Apr 4 20:51:14 2016:type=update:id=10.61.236.97@pts/1:user=admin:cmd=echo "hostname LAB" | vsh (SUCCESS)
Mon Apr 4 20:51:14 2016:type=start:id=vsh.9326:user=admin:cmd=
Mon Apr 4 20:51:14 2016:type=update:id=vsh.9326:user=admin:cmd=configure terminal ; hostname LAB (SUCCESS)
LAB# echo "hostname NEXUS-LABSWITCH" | vsh
NEXUS-LABSWITCH#
Mon Apr 4 20:51:23 2016:type=update:id=10.61.236.97@pts/1:user=admin:cmd=echo "hostname NEXUS-LABSWITCH" | vsh (SUCCESS)
Mon Apr 4 20:51:23 2016:type=start:id=vsh.9390:user=admin:cmd=
Mon Apr 4 20:51:23 2016:type=update:id=vsh.9390:user=admin:cmd=configure terminal ; hostname NEXUS-LABSWITCH (SUCCESS)
N5600-Lab# show run | i hostname | sed "s/N5600-Lab/N56128/" | vsh
N56128#
N56128# show accounting log | last 3
Mon Apr 4 21:23:23 2016:type=start:id=vsh.6762:user=admin:cmd=
Mon Apr 4 21:23:23 2016:type=update:id=vsh.6762:user=admin:cmd=configure terminal ; hostname N56128 (SUCCESS)
Mon Apr 4 21:23:23 2016:type=stop:id=vsh.6762:user=admin:cmd=
N5600-Lab# echo "hostname N56128" > bootflash:CLI
N5600-Lab#
N5600-Lab# show file CLI
hostname N56128
N5600-Lab# show file CLI | vsh
N56128#
O diff representa a diferença
N5600-Lab# show int mgmt0 | diff
N5600-Lab# show int mgmt0 | diff
11,12c11,12
< 9393 input packets 829764 bytes
< 141 unicast packets 3715 multicast packets
---
> 9395 input packets 830217 bytes
> 142 unicast packets 3716 multicast packets
15,16c15,16
< 214 output packets 47396 bytes
< 27 unicast packets 181 multicast packets
---
> 215 output packets 47640 bytes
> 27 unicast packets 182 multicast packets
N9K representa o nexo 9000
BRU-N9K3-1# watch differences interval 1 show int mgmt0 counter
Every 1.0s: vsh -c "show int mgmt0 counter" Mon Apr 4 23:42:27 2016
CCO reference
O CPU representa a unidade de processamento central
Este comando fornece os segundos cada 5 output (pode ser mudado) que processo está consumindo o CPU. É a mesma saída que o commnad da parte superior do linux:
NEXUS# show system internal processes cpu 5 | no-more
top - 12:41:55 up 117 days, 17:00, 5 users, load average: 0.44, 0.50, 0.55Tasks: 2883 total, 2 running, 1022 sleeping, 0 stopped, 1859 zombieCpu(s): 1.0%us, 0.9%sy, 0.0%ni, 98.0%id, 0.0%wa, 0.0%hi, 0.1%si, 0.0%stMem: 32744992k total, 14563132k used, 18181860k free, 61308k buffersSwap: 0k total, 0k used, 0k free, 4091160k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 18465 admin 20 0 5200 3108 1148 R 16.6 0.0 0:00.17 top 6389 root 20 0 699m 53m 14m S 3.3 0.2 113:49.07 netstack 18473 root 20 0 97940 3804 2796 R 3.3 0.0 0:00.02 vsh 10 root 15 -5 0 0 0 S 1.7 0.0 9:10.85 ksoftirqd/2 4876 root 15 -5 369m 27m 6564 S 1.7 0.1 67:33.91 sysmgr 9581 svc-isan 20 0 446m 41m 11m S 1.7 0.1 21:16.15 isis_l2mp 1 root 20 0 1980 652 572 S 0.0 0.0 3:02.73 init 2 root 15 -5 0 0 0 S 0.0 0.0 0:00.03 kthreadd 3 root RT -5 0 0 0 S 0.0 0.0 0:00.49 migration/0 4 root 15 -5 0 0 0 S 0.0 0.0 22:48.66 ksoftirqd/0 5 root -2 -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 6 root RT -5 0 0 0 S 0.0 0.0 0:00.65 migration/1 7 root 15 -5 0 0 0 S 0.0 0.0 2:27.70 ksoftirqd/1 top - 12:42:01 up 117 days, 17:00, 5 users, load average: 0.37, 0.48, 0.54Tasks: 2887 total, 1 running, 1027 sleeping, 0 stopped, 1859 zombieCpu(s): 1.0%us, 0.9%sy, 0.0%ni, 98.0%id, 0.0%wa, 0.0%hi, 0.1%si, 0.0%stMem: 32744992k total, 14562360k used, 18182632k free, 61308k buffersSwap: 0k total, 0k used, 0k free, 4091160k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 18502 admin 20 0 5200 3112 1148 R 18.5 0.0 0:00.17 top 6389 root 20 0 699m 53m 14m S 1.7 0.2 113:49.08 netstack 6402 root -2 0 366m 13m 8660 S 1.7 0.0 1032:41 clx 9015 root 20 0 482m 21m 11m S 1.7 0.1 225:45.72 pm 10066 svc-isan 20 0 403m 22m 9.9m S 1.7 0.1 268:31.28 ospf 10487 svc-isan 20 0 354m 9992 6596 S 1.7 0.0 194:52.11 ecp 1 root 20 0 1980 652 572 S 0.0 0.0 3:02.73 init 2 root 15 -5 0 0 0 S 0.0 0.0 0:00.03 kthreadd 3 root RT -5 0 0 0 S 0.0 0.0 0:00.49 migration/0 4 root 15 -5 0 0 0 S 0.0 0.0 22:48.66 ksoftirqd/0 5 root -2 -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 6 root RT -5 0 0 0 S 0.0 0.0 0:00.65 migration/1 7 root 15 -5 0 0 0 S 0.0 0.0 2:27.70 ksoftirqd/1
N7k/N9k
N7k-LabSW# show version internal build-identifier
Kickstart image file: bootflash:///n7000-s2-kickstart.6.2.10.bin : S102
System image file: bootflash:///n7000-s2-dk9.6.2.10.bin : S102
BRU-N9K3-1# show version internal build-identifier
nxos image file: bootflash:///nxos.7.0.3.I2.2a.bin : S30
N5k/6k:
N5600-Lab# show platform fwm info global | i FwM
FwM build Details: Built at Sat Apr 18 11:11:18 PDT 2015 on nuo-sw-build40 in directory /auto/n5kiluka/daily_build/iplus/nexus/522/src/build by buildsa)