Nexus 9236C spineswitch - CPS vervangen
Inhoud
Inleiding
Dit document beschrijft de stappen die nodig zijn om een defecte spineswitch (Nexus 9236C) te vervangen in een Ultra-M instelling waar Cisco Policy Suite (CPS) virtuele netwerkfuncties (VPN’s) worden opgeslagen.
Achtergrondinformatie
Ultra-M is een vooraf verpakte en gevalideerde gevirtualiseerde mobiele pakketoplossing die is ontworpen om de plaatsing van VPN's te vereenvoudigen. De servers die deel uitmaken van de Ultra-M-instelling, zijn verbonden met drie verschillende typen switches:
- Catalyst switch
- bladeswitch
- Spineswitch
De netwerktopologie van een instelling Ultra-M is zoals in deze afbeelding te zien:
UltraM-netwerktopologie
Afkortingen
| VNF | Virtuele netwerkfunctie |
| CENTRIFUGEREN | Nexus 9236C switch als spine |
| MOP | Procedure |
| LAN | Local Area Network |
| FTP | File Transfer Protocol |
| TFTP | Trial File Transfer Protocol |
| CIMC | Cisco geïntegreerde beheercontroller |
| BGP | Border Gateway-protocol |
| BFD | Detectie van bidirectionele doorsturen |
Werkstroom van de MoP
Werkstroom van de vervangingsprocedure op hoog niveau
Spineswitch in Ultra-M Setup
Voorwaarden
Neem een back-up van het configuratiebestand uit de spineswitch met behulp van ftp/tftp voordat u doorgaat met de schakelaar vervanging zoals hier wordt getoond.
Nexus-POD1-spine2# copy running-config sftp:
Enter destination filename: [Nexus-POD1-spine2-running-config] backup-spine-cfg-2
Enter vrf (If no input, current vrf 'default' is considered): management
Enter hostname for the sftp server: 10.1.1.1
Enter username: admin
The authenticity of host '10.1.1.1 (10.1.1.1)' can't be established.
RSA key fingerprint is SHA256:fnbUmd2mL5yE94zxrRoKAlvYfQbheXJfQox7m3XfpIU.
Are you sure you want to continue connecting (yes/no)? yes
Warning: Permanently added '10.1.1.1' (RSA) to the list of known hosts.
User Access Verification
Password:
Connected to 10.1.1.1.
sftp> put /var/tmp/vsh/backup-spine-cfg-2 backup-spine-cfg-2
Uploading /var/tmp/vsh/backup-spine-cfg-2 to /backup-spine-cfg-2
/var/tmp/vsh/backup-spine-cfg-2 100% 33KB 33.2KB/s 00:00
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.
Nexus-POD1-spine2#
Gezondheidscontroles
1. Controleer de huidige softwareversie die in de schakelaar draait en noteer deze zoals hier wordt weergegeven.
Nexus-POD1-spine2# show ver
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2018, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source. This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0 or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.
Software
BIOS: version 07.59
NXOS: version 7.0(3)I7(3)
BIOS compile time: 08/26/2016
NXOS image file is: bootflash:///nxos.7.0.3.I7.3.bin
NXOS compile time: 2/12/2018 13:00:00 [02/12/2018 19:13:48]
Hardware
cisco Nexus9000 C9236C chassis
Intel(R) Xeon(R) CPU @ 1.80GHz with 16400560 kB of memory.
Processor Board ID FDO21120SSN
Device name: Nexus-POD1-spine2
bootflash: 53298520 kB
Kernel uptime is 108 day(s), 13 hour(s), 15 minute(s), 12 second(s)
Last reset
Reason: Unknown
System version: 7.0(3)I7(3)
Service:
plugin
Core Plugin, Ethernet Plugin
Active Package(s):
2. Controleer het huidige licentiegebruik.
Nexus-POD1-spine2# show license usage
Feature Ins Lic Status Expiry Date Comments
Count
--------------------------------------------------------------------------------
N9K_LIC_1G No - Unused -
VPN_FABRIC No - Unused -
FCOE_NPV_PKG No - Unused -
SECURITY_PKG No 0 Unused -
N9K_UPG_EX_10G No - Unused -
TP_SERVICES_PKG No - Unused -
NXOS_ADVANTAGE_GF No - Unused -
NXOS_ADVANTAGE_M4 No - Unused -
NXOS_ADVANTAGE_XF No - Unused -
NXOS_ESSENTIALS_GF No - Unused -
NXOS_ESSENTIALS_M4 No - Unused -
NXOS_ESSENTIALS_XF No - Unused -
SAN_ENTERPRISE_PKG No - Unused -
PORT_ACTIVATION_PKG No 0 Unused -
NETWORK_SERVICES_PKG No - Unused -
NXOS_ADVANTAGE_M8-16 No - Unused -
NXOS_ESSENTIALS_M8-16 No - Unused -
FC_PORT_ACTIVATION_PKG No 0 Unused -
LAN_ENTERPRISE_SERVICES_PKG Yes - In use Never -
--------------------------------------------------------------------------------
3. Zorg ervoor dat de fysieke kabels die zijn aangesloten op het kanaal van de schakelaar, VLAN en ook de poortstatus goed zijn zoals verwacht.
Nexus-POD1-spine2# show interface status | grep connected
mgmt0 -- connected routed full 100 --
Eth1/1 -- connected trunk full 100G QSFP-100G-AOC5M
Eth1/2 -- connected trunk full 100G QSFP-100G-AOC5M
Eth1/5 -- connected trunk full 100G QSFP-100G-AOC5M
Eth1/6 -- connected trunk full 100G QSFP-100G-AOC5M
Eth1/11/1 Connected to NMNET connected 101 full 10G QSFP-40G-SR4
Eth1/21/1 -- connected routed full 10G QSFP-40G-SR4
Eth1/21/2 -- connected routed full 10G QSFP-40G-SR4
Eth1/21/3 -- connected routed full 10G QSFP-40G-SR4
Eth1/21/4 -- connected routed full 10G QSFP-40G-SR4
Eth1/22/1 -- connected routed full 10G QSFP-40G-SR4
Eth1/22/2 -- connected routed full 10G QSFP-40G-SR4
Eth1/22/3 -- connected routed full 10G QSFP-40G-SR4
Eth1/22/4 -- connected routed full 10G QSFP-40G-SR4
Eth1/23/1 -- connected routed full 10G QSFP-40G-SR4
Eth1/23/2 -- connected routed full 10G QSFP-40G-SR4
Eth1/23/3 -- connected routed full 10G QSFP-40G-SR4
Eth1/23/4 -- connected routed full 10G QSFP-40G-SR4
Eth1/29 "spine-spine link" connected trunk full 100G QSFP-100G-AOC5M
Eth1/30 "spine-spine link" connected trunk full 100G QSFP-100G-AOC5M
Eth1/31 "spine-spine link" connected trunk full 100G QSFP-100G-AOC5M
Po22 portchannel to Lea connected trunk full 100G --
Po24 portchannel to Lea connected trunk full 100G --
Po30 -- connected routed full 10G --
Po30.3201 -- connected routed full 10G --
Po30.3202 -- connected routed full 10G --
Po30.3203 -- connected routed full 10G --
Po30.3204 -- connected routed full 10G --
Po30.3205 -- connected routed full 10G --
Po30.3206 -- connected routed full 10G --
Po99 spine1-spine2 connected trunk full 100G --
Lo1 -- connected routed auto auto --
Lo2 -- connected routed auto auto --
Lo3 -- connected routed auto auto --
Lo4 -- connected routed auto auto --
Lo5 -- connected routed auto auto --
Vlan2601 Global VRF spine-2 connected routed auto auto --
Vlan2602 GI VRF spine-2 <-> connected routed auto auto --
Vlan2603 IPV6SUB VRF spine- connected routed auto auto --
Vlan2604 METROE-E VRF spine connected routed auto auto --
Vlan2605 NMNET VRF spine-2 connected routed auto auto --
Vlan2721 Global VRF spine-2 connected routed auto auto --
Vlan2722 GI VRF spine-2 <-> connected routed auto auto --
Vlan2723 IPV6SUB VRF spine- connected routed auto auto --
Vlan2724 METROE-E VRF spine connected routed auto auto --
Vlan2741 Global VRF spine-2 connected routed auto auto --
Vlan2742 GI VRF spine-2 <-> connected routed auto auto --
Vlan2743 IPV6SUB VRF spine- connected routed auto auto --
Vlan2744 METROE-E VRF spine connected routed auto auto --
4. Zorg ervoor dat de buren van het Border Gateway Protocol (BGP) in de buurt zijn.
Nexus-POD1-spine2# show ip bgp summary vrf all
BGP summary information for VRF GI, address family IPv4 Unicast
BGP router identifier 10.0.202.2, local AS number 65145
BGP table version is 28, IPv4 Unicast config peers 4, capable peers 4
1 network entries and 1 paths using 236 bytes of memory
BGP attribute entries [1/160], BGP AS path entries [1/6]
BGP community entries [0/0], BGP clusterlist entries [0/0]
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
10.0.92.1 4 65145 312621 312617 28 0 0 15w3d 1
10.0.122.2 4 65251 312624 312616 28 0 0 15w3d 0
10.0.142.2 4 65252 312623 312617 28 0 0 15w3d 0
10.178.240.185 4 65137 312618 312616 28 0 0 12w0d 0
BGP summary information for VRF IPV6SUB, address family IPv4 Unicast
BGP summary information for VRF METROE-E, address family IPv4 Unicast
BGP router identifier 10.0.202.4, local AS number 65145
BGP table version is 10, IPv4 Unicast config peers 4, capable peers 4
1 network entries and 1 paths using 236 bytes of memory
BGP attribute entries [1/160], BGP AS path entries [1/6]
BGP community entries [0/0], BGP clusterlist entries [0/0]
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
10.0.94.1 4 65145 312619 312617 10 0 0 15w3d 1
10.0.124.2 4 65251 312623 312616 10 0 0 15w3d 0
10.0.144.2 4 65252 312618 312617 10 0 0 15w3d 0
10.178.240.181 4 65137 312618 312616 10 0 0 12w0d 0
BGP summary information for VRF NMNET, address family IPv4 Unicast
BGP router identifier 10.0.202.5, local AS number 65145
BGP table version is 3, IPv4 Unicast config peers 1, capable peers 1
1 network entries and 1 paths using 236 bytes of memory
BGP attribute entries [1/160], BGP AS path entries [0/0]
BGP community entries [0/0], BGP clusterlist entries [0/0]
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
10.0.95.1 4 65145 312616 312616 3 0 0 15w3d 1
BGP summary information for VRF default, address family IPv4 Unicast
BGP router identifier 10.0.202.1, local AS number 65145
BGP table version is 261, IPv4 Unicast config peers 4, capable peers 3
35 network entries and 49 paths using 10108 bytes of memory
BGP attribute entries [5/800], BGP AS path entries [3/22]
BGP community entries [0/0], BGP clusterlist entries [0/0]
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
10.0.91.1 4 65145 312681 312635 261 0 0 15w3d 35
10.0.121.2 4 65251 312629 312630 261 0 0 15w3d 0
10.0.141.2 4 65252 312683 312620 261 0 0 15w3d 14
10.178.240.177 4 65137 0 124577 0 0 0 15w3d 12
Nexus-POD1-spine2# show ipv6 bgp summary vrf all
BGP summary information for VRF GI, address family IPv6 Unicast
BGP router identifier 10.0.202.2, local AS number 65145
BGP table version is 64, IPv6 Unicast config peers 4, capable peers 4
1 network entries and 1 paths using 248 bytes of memory
BGP attribute entries [1/160], BGP AS path entries [1/6]
BGP community entries [0/0], BGP clusterlist entries [0/0]
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
fc00:420:81:122::2
4 65251 312637 312629 64 0 0 15w3d 0
fc00:420:81:142::2
4 65252 312637 312630 64 0 0 15w3d 0
fc00:420:81:992::1
4 65145 312635 312630 64 0 0 15w3d 1
fd01:976a:c002:1:4d13:36f3:0:22
4 65137 312631 312627 64 0 0 12w0d 0
BGP summary information for VRF IPV6SUB, address family IPv6 Unicast
BGP router identifier 10.0.202.3, local AS number 65145
BGP table version is 44, IPv6 Unicast config peers 4, capable peers 4
0 network entries and 0 paths using 0 bytes of memory
BGP attribute entries [0/0], BGP AS path entries [0/0]
BGP community entries [0/0], BGP clusterlist entries [0/0]
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
fc00:420:81:123::2
4 65251 312632 312629 44 0 0 15w3d 0
fc00:420:81:143::2
4 65252 312636 312629 44 0 0 15w3d 0
fc00:420:81:993::1
4 65145 312631 312629 44 0 0 15w3d 0
fd01:976a:c002:1:4d13:36f3:0:24
4 65137 312629 312628 44 0 0 12w0d 0
BGP summary information for VRF METROE-E, address family IPv6 Unicast
BGP summary information for VRF NMNET, address family IPv6 Unicast
BGP summary information for VRF default, address family IPv6 Unicast
5. Zorg ervoor dat de buurstaat Bidirectional Forwarding Detection (BFD) Up is.
Nexus-POD1-spine2# show bfd neighbors vrf al
OurAddr NeighAddr LD/RD RH/RS Holdown(mult) State Int Vrf
10.0.124.1 10.0.124.2 1090519045/1090519205 Up 672(3) Up Vlan2724 METROE-E
10.0.122.1 10.0.122.2 1090519046/1090519206 Up 639(3) Up Vlan2722 GI
10.0.92.2 10.0.92.1 1090519050/1090519094 Up 585(3) Up Vlan2602 GI
10.0.95.2 10.0.95.1 1090519051/1090519095 Up 585(3) Up Vlan2605 NMNET
10.0.121.1 10.0.121.2 1090519052/1090519208 Up 639(3) Up Vlan2721 default
10.0.94.2 10.0.94.1 1090519054/1090519097 Up 585(3) Up Vlan2604 METROE-E
10.0.91.2 10.0.91.1 1090519055/0 Up N/A(3) Up Vlan2601 default
10.0.141.1 10.0.141.2 1090519056/1090519212 Up 610(3) Up Vlan2741 default
10.0.144.1 10.0.144.2 1090519057/1090519213 Up 610(3) Up Vlan2744 METROE-E
10.0.142.1 10.0.142.2 1090519059/1090519214 Up 610(3) Up Vlan2742 GI
10.178.240.182 10.178.240.181 1090519061/0 UP N/A(3) Up Po30.3202 METROE-E
10.178.240.186 10.178.240.185 1090519062/0 Up N/A(3) Up Po30.3203 GI
Nexus-POD1-spine2#
Nexus-POD1-spine2# show bfd ipv6 neighbor vrf all
OurAddr NeighAddr
LD/RD RH/RS Holdown(mult) State Int Vrf
fc00:420:81:123::1 fc00:420:81:123::2
1090519044/1090519204 Up 615(3) Up Vlan2723 IPV6SUB
fc00:420:81:122::1 fc00:420:81:122::2
1090519047/1090519207 Up 731(3) Up Vlan2722 GI
fc00:420:81:142::1 fc00:420:81:142::2
1090519048/1090519210 Up 696(3) Up Vlan2742 GI
fc00:420:81:143::1 fc00:420:81:143::2
1090519049/1090519211 Up 696(3) Up Vlan2743 IPV6SUB
fc00:420:81:993::2 fc00:420:81:993::1
1090519053/1090519096 Up 544(3) Up Vlan2603 IPV6SUB
fc00:420:81:992::2 fc00:420:81:992::1
1090519058/1090519099 Up 544(3) Up Vlan2602 GI
Switch-vervangingsprocedure
1. Installeer de nieuwe schakelaar in het rek en sluit de kabels aan op de schakelaar zoals aangegeven. U vindt hier de stappen voor de installatie van de schakelaar: Toets Nexus 236C NX-OS modus Switch Hardware Installatie-gids
2. Controleer de softwareversie van de Nexus Spineswitch en upgrade/downgrade naar de softwareversie via deze link: Cisco Nexus 9000 Series NX-OS software-upgrade en downgraads, release 7.x
3. Breng de configuratie back-up over naar de nieuwe schakelaar en kopieer de configuratie naar de opstartconfiguratie.
server-backup$ sftp admin@10.1.1.1
The authenticity of host '10.1.1.1 (10.1.1.1)' can't be established.
RSA key fingerprint is SHA256:fnbUmd2mL5yE94zxrRoKAlvYfQbheXJfQox7m3XfpIU.
Are you sure you want to continue connecting (yes/no)? yes
Warning: Permanently added '10.1.1.1' (RSA) to the list of known hosts.
User Access Verification
Password:
Password:
Connected to 10.1.1.1.
sftp> ls
20170607_193430_poap_15489_1.log 20170607_193430_poap_15489_2.log 20170607_193430_poap_15489_init.log backup-spine-cfg-2 backup-spine.cfg
backup_run_02152018 bios_daemon.dbg cfg-july25th cfg-july25th-spine1 flash:
flash:cfg-aug8th-ybattina-afterNSO flash:cfg-jul28th home l3-cfg-aug10th license_FDO211406K1_16.lic
lost+found nxos.7.0.3.I4.4.bin nxos.7.0.3.I5.2.bin nxos.7.0.3.I7.3.bin platform-sdk.cmd
scripts spine-config-bkp starat virtual-instance vlan.dat 100% 33KB 21.7KB/s 00:01
sftp> put backup-spine-cfg-2
Uploading backup-spine-cfg-2 to /backup-spine-cfg-2
backup-spine-cfg-2 100% 33KB 23.5KB/s 00:01
sftp> bye
Nexus-spine1# copy bootflash:///backup-spine-cfg-2 startup-config
Copy progress 100% 33KB
Copy complete, now saving to disk (please wait)...
Copy complete.
4. Laad de schakelaar opnieuw nadat u de reserveconfiguratie hebt geladen.
Nexus-POD1-spine2#reload
Controleer de vervangen centrifugeswitch
Nadat de schakelaar voor toegang beschikbaar is, voert u de gezondheidscontroles uit met het gebruik van deze opdrachten op de Spineswitch om te controleren of een vervangen schakelaar in de verwachte staat beschikbaar is.
Nexus-POD1-spine2# show port-channel summary
Nexus-POD1-spine2# show ip bgp summary vrf all
Nexus-POD1-spine2# show ipv6 bgp summary vrf all
Nexus-POD1-spine2# show bfd neighbor vrf all
Nexus-POD1-spine2# show bfd ipv6 neighbor vrf all
FeedbackContact Cisco
- Een ondersteuningscase openen
- (Vereist een Cisco-servicecontract)