Detecteer Layer 2 hardware op Catalyst 9000 Series Switches
Inhoud
Inleiding
Dit document beschrijft hoe u Layer 2 hardware-programmering en -verzending kunt valideren op Catalyst 9400 Series switches.
Voorwaarden
Vereisten
Er zijn geen specifieke vereisten van toepassing op dit document.
Gebruikte componenten
De informatie in dit document is gebaseerd op Catalyst 9400 (UADP 2.0) Series switch.
De informatie in dit document is gebaseerd op de apparaten in een specifieke laboratoriumomgeving. Alle apparaten die in dit document worden beschreven, hadden een opgeschoonde (standaard)configuratie. Als uw netwerk live is, moet u zorgen dat u de potentiële impact van elke opdracht begrijpt.
Achtergrondinformatie
- Catalyst 9400 supervisor 1 (C9400-SUP-1) heeft 3 UADP 2.0 UADP 2.0 UPTS ASIC’s (0, 1, 2).
- Elke UADP 2.0 verzendASIC heeft:
- Een dual Core (0, 1) - deze bestond niet in eerdere generaties van UADP 2.0 ASICS.
- SIFs (Stack Interfaces) - gebruikt om verbinding te maken met de andere 2 UADP 2.0 ASIC’s via een interne stackring.
- NIF's (Network Interfaces) - gebruikt voor de aansluiting op 1 of meer lijnkaarten via de backplane.
- Alle pakket die besluiten voor de kaarten van de Lijnkaart en de van de Supervisor uplink interfaces worden gemaakt door de 3 UADP 2.0 die ASICs op de actieve supervisor door te sturen.
- De lijnkaarten die in dit voorbeeld worden gebruikt hebben 1 lijnkaart enkele kern stub ASIC die niet bij pakket het verzenden besluiten betrokken is.
- De lijnkaartstap ASIC op de lijnkaart sluit aan op 1 of meer van de 3 UADP 2.0 die ASICs op de supervisor via het backplane door te sturen.
- De 3 UADP 2.0 die ASICs op de supervisor door te sturen maken alle pakket besluiten.
Terminologie
| acroniem |
Definitie |
| RP |
routeprocessor |
| KP |
Doorvoerprocessor |
| FED |
Stuurprogramma doorsturen. Het softwareproces dat de Supervisor Forwarding ASIC omvat. |
| Objectmanager |
FP software MAC-items die als asynchrone objecten in de doeldatabase worden opgeslagen. |
| LSMPI |
Linux Shared Memory Point Interface Het transport tussen het gegevensvliegtuig (hardware-UADP 2.0) en het besturingsplane (software-CPU). |
| IFM |
Software voor interfacebeheer. |
| IF_ID |
Interface IDentifier is een unieke waarde die een specifieke interface representeert. Het wordt gebruikt tijdens interne programmering in de switch. |
| Instellen |
Bijvoorbeeld. Geeft aan dat de UADP 2.0 Asic/Core-interface is aangesloten op: 0=Asic0/Core0, 1=Asic0/Core1, 2=Asic1/Core0, 3=Asic1/Core1, 4=Asic2/Core0, 5=Asic2/Core1. |
| Aziatisch |
Specificeert welke UADP 2.0 een interface met: 0=UADP 2.0 #0, 1=UADP 2.0 #1, 2= UADP 2.0 #2. |
| kern |
Specificeert welke kern op de UADP 2.0 interface is gekoppeld aan: 0=kern0, 1=kern1. |
| Port |
Ordinaal nummer van een haven in een sleuf. Binnen dezelfde sleuf zijn alle poortnummers uniek. |
| Subpoort |
Identificeert een haven binnen een havengroep (Cntx) voor voorpaneelpoorten die worden gesubporteerd (Cntx & SubPort samen een unieke haven die wordt Sub-porteerd). |
| Mac |
Interface identifier die wordt gebruikt wanneer een interface MACsec (security verificatie en encryptie) draait. |
| Cntx |
Context. Een groepsnummer dat een poort behoort tot wanneer een interface op het voorpaneel wordt gesubporteerd (Cntx & SubPort samen identificeren een unieke haven die wordt Sub-porteerd). |
| LPN |
Logisch poortnummer gekoppeld aan een interface. |
| GPN |
Mondiaal poortnummer gekoppeld aan een interface. |
| type NIF |
Netwerkinterface; NRU = Network Redundant Uplink |
| IF_IS |
Interface-IDentifier. Dit is een unieke waarde die een specifieke interface representeert. Het wordt gebruikt tijdens verschillende programma's intern in de switch. |
| PoortLE |
Logische entiteit van de haven. Dit is de interfaceconfiguratie. |
| AOM |
Asynchrone objectmanager. De informatie over de KP-programma's in de doeldatabase als object. |
| VP |
Virtuele poort |
| MATM |
MAC-adrestabelbeheer |
| RP |
routeprocessor |
| OM_PTR |
Pointer om object Manager |
| Tbl_ID |
Tabelidentificator = vlan |
| CMAN |
Chassis Manager |
| KP |
Doorvoerprocessor |
| fp_port |
De voorpaneelpoorten. |
| Sif |
Stack interface (naar de andere 2 UADP 2.0 die ASIC's op de supervisor doorsturen). |
| Nif |
Netwerkinterface (naar de interface van het voorpaneel) |
| IGR/EGR |
Ingoers / egress |
| IQS |
Ingraving Wachtende wachtrij |
| QO |
Stack Queue Scheduler |
| PBC |
Packet Buffer-complex |
| AQM |
Actief beheer van de wachtrij. Dit controleert congestiebeheer. |
| AQMRed |
Actieve vroegtijdige detectie van wachtrijbeheer. |
| EQC |
IP-wachtrij |
| ESM |
Edge-planningsbeheer |
| RWE |
Herschrijfmachine. Voert veldnameninformatie toe of verwijdert deze uit het pakket. |
| IOMD |
Stuurprogramma voor ingangsmodule |
| fp_port |
De voorpaneel poort. |
| Nif |
Netwerkinterface (naar de interface van het voorpaneel) |
| SLI |
System Link Interface (naar supervisor) |
| IGR / EGR = |
Ingoers / egress |
| AQMRed |
Actieve vroegtijdige detectie van wachtrijbeheer. |
| OCI |
Out-of-band regelinterface = intern communicatiekanaal tussen de lijnkaart en actieve supervisor |
| MATM |
MAC-adrestabelbeheer |
| MAC-verplaatsing aantal |
Dit is de telling voor wanneer een adres van MAC zich op een nieuwe interface beweegt (wordt geleerd). De bewegingtel kan voorkomen wanneer een eindhost fysiek van de ene interface naar de andere wordt verplaatst, een draadloos host-venster van het ene Access Point (AP) naar een andere AP die op een andere interface is aangesloten, of de overspannend-tree path veranderingen of loops. |
Lijnkaart voor UADP
Topologie
C9400#show version Cisco IOS XE Software, Version 16.06.01 Cisco IOS Software [Everest], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.6.1, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2017 by Cisco Systems, Inc. Compiled Sat 22-Jul-17 05:51 by mcpre --snip--
C9400#show module Chassis Type: C9407R Mod Ports Card Type Model Serial No. ---+-----+--------------------------------------+--------------+-------------- 1 48 48-Port 10/100/1000 (RJ-45) C9400-LC-48T JAE211703RC 2 48 48-Port UPOE 10/100/1000 (RJ-45) C9400-LC-48U JAE21150CGD 3 10 Supervisor 1 Module C9400-SUP-1 JAE21240235 4 10 Supervisor 1 Module C9400-SUP-1 JAE21240235 5 48 48-Port UPOE 10/100/1000 (RJ-45) C9400-LC-48U JAE21150CG9 Mod MAC addresses Hw Fw Sw Status ---+--------------------------------+----+------------+------------------+-------- 1 E4AA.5D54.C84C to E4AA.5D54.C87B 0.6 16.6.1r [FC 16.06.01 ok 2 E4AA.5D54.B430 to E4AA.5D54.B45F 0.6 16.6.1r [FC 16.06.01 ok 3 2C5A.0F1C.28EC to 2C5A.0F1C.28F5 0.6 16.6.1r [FC 16.06.01 ok 4 2C5A.0F1C.28F6 to 2C5A.0F1C.28FF 0.6 16.6.1r [FC 16.06.01 ok 5 E4AA.5D54.B658 to E4AA.5D54.B687 0.6 16.6.1r [FC 16.06.01 ok Mod Redundancy Role Operating Redundancy Mode Configured Redundancy Mode ---+-------------------+-------------------------+--------------------------- 3 Active sso sso 4 Standby sso sso
C9400#show running-config interface port-channel 1 interface Port-channel1 switchport trunk allowed vlan 100 switchport mode trunk
C9400#show running-config interface gigabitEthernet 1/0/13 interface GigabitEthernet1/0/13 switchport trunk allowed vlan 100 switchport mode trunk channel-group 1 mode active
C9400#show running-config interface gigabitEthernet 5/0/21 interface GigabitEthernet5/0/21 switchport trunk allowed vlan 100 switchport mode trunk channel-group 1 mode active
C9400#show etherchannel summary --snip-- Group Port-channel Protocol Ports ------+-------------+-----------+----------------------------------------------- 1 Po1(SU) LACP Gi1/0/13(P) Gi5/0/21(P)
Interfaceprogrammering
Toewijzing van interface naar UADP 2.0
De opdracht Interfaceprogrammeur toont de interface-afbeelding van het voorpaneel voor alle Lijnkaarten aan één van de 3 UADP 2.0 die ASIC op de actieve supervisor door maakt.
Uitloopvoorbeeld
Dit voorbeeld toont aan dat:
- Interface Gig1/0/3 wordt aangesloten op: UADP 2.0, 2 (UADP 2.0 Asic 1, Core 0), op de supervisor.
- Interface Gig5/0/21 is verbonden met: UADP 2.0 instantie 3 (UADP 2.0 Asic 1, Core 1) op de supervisor.
C9400#show platform software fed active ifm mappings
Interface IF_ID Inst Asic Core Port SubPort Mac Cntx LPN GPN Type Active GigabitEthernet1/0/1 0x7 2 1 0 0 0 4 4 1 101 NIF Y GigabitEthernet1/0/2 0x8 2 1 0 1 1 4 4 2 102 NIF Y --snip-- GigabitEthernet1/0/13 0x13 2 1 0 12 4 0 0 13 1105 NIF Y --snip-- GigabitEthernet5/0/21 0x8f 3 1 1 20 4 5 5 21 1104 NIF Y --snip--
Fysieke interfaceprogramma
De opdracht Show platform geeft de configuratiegegevens van de software weer voor Gig1/0/3 op basis van de IF_ID waarde in het vorige opdrachtvoorbeeld.
C9400#show platform software fed active ifm if-id 0x13
Interface IF_ID : 0x0000000000000013
Interface Name : GigabitEthernet1/0/13
Interface Block Pointer : 0x7fe5c5aab7b8
Interface State : READY
Interface Status : ADD, UPD
Interface Ref-Cnt : 7
Interface Type : ETHER
Port Type : SWITCH PORT
Port Location : LOCAL
Slot : 1
Unit : 0
Slot Unit : 13
SNMP IF Index : 14
GPN : 1105
EC Channel : 1
EC Index : 1
Port Handle : 0x72000285
LISP v4 Mobility : false
LISP v6 Mobility : false
QoS Trust Type : 0
Port Information
Handle ............ [0x72000285]
Type .............. [Layer2]
Identifier ........ [0x13]
Slot .............. [1]
Unit .............. [13]
Port Physical Subblock
Affinity .......... [local]
Asic Instance ..... [2 (A:1,C:0)]
AsicPort .......... [12]
AsicSubPort ....... [4]
MacNum ............ [0]
ContextId ......... [0]
LPN ............... [13]
GPN ............... [113]
Speed ............. [1GB]
type .............. [NIF]
PORT_LE ........... [0x7fe5c5aabc28]
L3IF_LE ........... [0x0]
EC GPN ............ [1105]
EC L3IF_LE ........ [0x0]
EC Port Mask ...... [0xaaaaaaaaaaaaaaaa]
DI ................ [0x7fe5c5ab5c48]
Port L2 Subblock
Enabled ............. [Yes]
Allow dot1q ......... [Yes] ---> interface Gig1/0/13 is configured as a trunk
Allow native ........ [Yes]
Default VLAN ........ [1]
Allow priority tag ... [Yes]
Allow unknown unicast [Yes]
Allow unknown multicast[Yes]
Allow unknown broadcast[Yes]
Allow unknown multicast[Enabled]
Allow unknown unicast [Enabled]
IPv4 ARP snoop ....... [No]
IPv6 ARP snoop ....... [No]
Jumbo MTU ............ [1500]
Learning Mode ........ [1]
Port QoS Subblock
Trust Type .................... [0x2]
Default Value ................. [0]
Ingress Table Map ............. [0x0]
Egress Table Map .............. [0x0]
Queue Map ..................... [0x0]
Port Netflow Subblock
Port Policy Subblock
List of Ingress Policies attached to an interface
List of Egress Policies attached to an interface
Ref Count : 7 (feature Ref Counts + 1)
IFM Feature Ref Counts
FID : 100, Ref Count : 1
FID : 57, Ref Count : 1
FID : 115, Ref Count : 1
FID : 17, Ref Count : 1
FID : 78, Ref Count : 1
FID : 30, Ref Count : 1
IFM Feature Sub block information
FID : 57, Private Data : 0x7fe5c685e748
FID : 17, Private Data : 0x7fe5c5e85f38
FID : 30, Private Data : 0x7fe5c5e85aa8
Deze opdracht geeft de hardwareconfiguratie van Gig1/0/3 weer, gebaseerd op de PORT_LE waarde van de vorige opdracht.
| Waarde |
Definitie |
| Waarde 0 |
De waarde wordt niet ingesteld. |
| Waarde 1 |
De waarde wordt in de meeste gevallen ingesteld. |
C9400#show platform hardware fed active fwd-asic abstraction print-resource-handle 0x7fe5c5aabc28 1 Handle:0x7fe5c5aabc28 Res-Type:ASIC_RSC_PORT_LE Res-Switch-Num:0 Asic-Num:2 Feature-ID:AL_FID_IFM Lkp-ftr-id:LKP_FEAT_INGRESS_PRECLASS1_IPV4 ref_count:1 priv_ri/priv_si Handle: (nil)Hardware Indices/Handles: index2:0xc mtu_index/l3u_ri_index2:0x4 sm handle [ASIC 2]: 0x7fe5c5abb588 Detailed Resource Information (ASIC#2) ----------------------------------------
LEAD_PORT_ALLOW_BROADCAST value 1 Pass LEAD_PORT_ALLOW_CAPWAP value 0 Pass LEAD_PORT_ALLOW_CTS value 0 Pass LEAD_PORT_ALLOW_DOT1Q_TAGGED value 1 Pass LEAD_PORT_ALLOW_MULTICAST value 1 Pass LEAD_PORT_ALLOW_NATIVE value 1 Pass LEAD_PORT_ALLOW_NON_CTS value 0 Pass LEAD_PORT_ALLOW_PRIORITY_TAGGED value 1 Pass LEAD_PORT_ALLOW_UNICAST value 1 Pass LEAD_PORT_ALLOW_UNKNOWN_ETHER_TYPE value 0 Pass LEAD_PORT_ALLOW_UNKNOWN_UNICAST value 1 Pass LEAD_PORT_ALLOW_VLAN_LOAD_BALANCE_GROUP value 15 Pass LEAD_PORT_ALLOW_VRF value 0 Pass LEAD_PORT_ARP_OR_ND_SNOOPING_ENABLED_IPV4 value 0 Pass LEAD_PORT_ARP_OR_ND_SNOOPING_ENABLED_IPV6 value 0 Pass LEAD_PORT_AUTH_MODE value 0 Pass LEAD_PORT_CAPWAP_TUNNEL value 0 Pass LEAD_PORT_CONTENT_MATCHING_ENABLED value 0 Pass LEAD_PORT_CTS_ENABLED value 0 Pass LEAD_PORT_CUSTOMER_PORT value 0 Pass LEAD_PORT_DAI_OR_ND_TRUST_MODE_IPV4 value 0 Pass LEAD_PORT_DAI_OR_ND_TRUST_MODE_IPV6 value 0 Pass LEAD_PORT_DATA_GLEAN_LEARN_IPV4 value 0 Pass --snip--
Ethernet-programma
In deze EtherChannel-programmeervoorbeeldoutput, de RP-programma's, de FP-programma's, de FED-programma's en vervolgens de ASIC-hardware van de supervisor doorsturen. De RP-softwareingangen worden als objecten in de doeldatabase opgeslagen en de FP-softwareingangen worden als asynchrone objecten in de doeldatabase opgeslagen.
C9400#show etherchannel summary --snip-- Group Port-channel Protocol Ports ------+-------------+-----------+----------------------------------------------- 1 Po1(SU) LACP Gi1/0/13(P) Gi5/0/21(P)
Het groepsmasker is een niet-nul in deze uitvoer. Het wordt in het hashproces gebruikt om de koppeling in het Ethernet-kanaal te bepalen waar een verkeersstroom zich beperkt.
C9400#show platform software interface rp active brief Forwarding Manager Interfaces Information Name ID QFP ID ------------------------------------------------------------- Null0 1 0 GigabitEthernet1/0/1 7 0 GigabitEthernet1/0/2 8 0 GigabitEthernet1/0/3 9 0 —snip— GigabitEthernet1/0/13 19 0 —snip— GigabitEthernet5/0/21 143 0 —snip— Port-channel1 748 0 —snip—
C9400#show platform software fed active etherchannel 1 group-mask
Group Mask Info
Aggport IIF Id: 00000000000002EC ---> hex 0x2EC = dec 748
Active Port: : 2 -------------------> 2 active interfaces in the etherchannel = the Member ports below
Member Ports
If Name If Id local Group Mask
-------------------------------------------------------------------
GigabitEthernet1/0/13 0000000000000013 true 5555555555555555 ---> hex 0x13 = dec 19
GigabitEthernet5/0/21 000000000000008f true aaaaaaaaaaaaaaaa ---> hex 0x8f = dec 143
Deze opdracht toont de configuratie voor poortkanaal 1:
C9400#show platform software fed active ifm if-id 0x000002ec Interface IF_ID : 0x00000000000002ec Interface Name : Port-channel1 Interface Block Pointer : 0x7fe5c685df98 Interface State : READY Interface Status : ADD, UPD Interface Ref-Cnt : 5 Interface Type : ETHERCHANNEL Port Type : SWITCH PORT Channel Number : 1 SNMP IF Index : 720 Port Handle : 0x50002f6 #Of Active Ports : 2 Base GPN : 1104 Index[2] : 0000000000000013 ---> Gig1/0/13 from previous command output Index[3] : 000000000000008f ---> Gig5/0/21 from previous command output Port Information Handle ............ [0x50002f6] Type .............. [L2-Ethchannel] Identifier ........ [0x2ec] Unit .............. [1] Port Logical Subblock L3IF_LE handle .... [0x0] Num physical port . [2] GPN Base .......... [1104] Num physical port on asic [0] is [0] DiBcam handle on asic [0].... [0x0] Num physical port on asic [1] is [0] DiBcam handle on asic [1].... [0x0] Num physical port on asic [2] is [1] ------------> Gig1/0/13 is on ASIC instance 2 (Supervisor ASIC 1, core 0) DiBcam handle on asic [2].... [0x7fe5c6ae3608] Num physical port on asic [3] is [1] ------------> Gig5/0/21 is on ASIC instance 3 (Supervisor ASIC 1, core 1) DiBcam handle on asic [3].... [0x7fe5c685d7e8] Num physical port on asic [4] is [0] DiBcam handle on asic [4].... [0x0] Num physical port on asic [5] is [0] DiBcam handle on asic [5].... [0x0] Port L2 Subblock Enabled ............. [No] Allow dot1q ......... [No] Allow native ........ [No] Default VLAN ........ [0] Allow priority tag ... [No] Allow unknown unicast [No] Allow unknown multicast[No] Allow unknown broadcast[No] Allow unknown multicast[Enabled] Allow unknown unicast [Enabled] IPv4 ARP snoop ....... [No] IPv6 ARP snoop ....... [No] Jumbo MTU ............ [0] Learning Mode ........ [0] Port QoS Subblock Trust Type .................... [0x7] Default Value ................. [0] Ingress Table Map ............. [0x0] Egress Table Map .............. [0x0] Queue Map ..................... [0x0] Port Netflow Subblock Port Policy Subblock List of Ingress Policies attached to an interface List of Egress Policies attached to an interface Ref Count : 5 (feature Ref Counts + 1) IFM Feature Ref Counts FID : 115, Ref Count : 1 FID : 78, Ref Count : 1 No Sub Blocks Present
Deze opdracht toont de configuratie voor mapping interfaces.
| Acroniem/instantie |
Definitie |
| IFM |
Interface Manager |
| voorbeeld |
Gig1/0/13 is op ASIC-exemplaar 2 (UADP 2.0 ASIC 1, kern 0) met interface-ID 0x13 |
| voorbeeld |
Gig5/0/21 is gebaseerd op ASIC-exemplaar 3 (UADP 2.0 ASIC 1, kern 1) met interface-ID 0x8f |
C9400#show platform software fed active ifm mappings
Interface IF_ID Inst Asic Core Port SubPort Mac Cntx LPN GPN Type Active GigabitEthernet1/0/1 0x7 2 1 0 0 0 4 4 1 101 NIF Y GigabitEthernet1/0/2 0x8 2 1 0 1 1 4 4 2 102 NIF Y --snip-- GigabitEthernet1/0/13 0x13 2 1 0 12 4 0 0 13 1105 NIF Y --snip-- GigabitEthernet5/0/21 0x8f 3 1 1 20 4 5 5 21 1104 NIF Y --snip--
Mondiale Ethernet-configuratie
C9400#show platform software ether-channel rp active global-config Forwarding Manager EtherChannel Global Configuration Information Frame Dist Method: Dest-IP-Address ---> distribution (hash) method: a packet's destination IP address is used to determine which etherchannel member link it is sent out on
C9400#show platform software ether-channel fp active global-config
Forwarding Manager EtherChannel Global Configuration Information
Frame Dist Method: Dest-IP-Address
AOM ID: 27
Status: Done ----------------> Programming in hardware is complete (FP received acknowledgement from FED)
C9400#show platform software object-manager fp active object 27 Object identifier: 27 Description: EtherChannel global configuration object Status: Done, Epoch: 0, Client data: 0x792e6e28
VLAN-programmering
C9400#show platform software fed active vlan 100 VLAN Fed Information Vlan Id IF Id LE Handle STP Handle L3 IF Handle SVI IF ID MVID --------------------------------------------------------------------------------------------------------------- 100 0x0000000000420011 0x00007fe5c4616ef8 0x00007fe5c4617778 0x00007fe5c50dac28 0x00000000000002ea 10
Deze opdracht geeft de instellingsdetails voor de hardwareconfiguratie voor VLAN 100 weer.
| Waarde |
Definitie |
| Waarde 0 |
De waarde wordt niet ingesteld. |
| Waarde 1 |
De waarde wordt in de meeste gevallen ingesteld. |
C9400#show platform hardware fed active fwd-asic abstraction print-resource-handle 0x00007fe5c4616ef8 1 Handle:0x7fe5c4616ef8 Res-Type:ASIC_RSC_VLAN_LE Res-Switch-Num:255 Asic-Num:255 Feature-ID:AL_FID_L2 Lkp-ftr-id:LKP_FEAT_INVALID ref_count:1 priv_ri/priv_si Handle: (nil)Hardware Indices/Handles: index0:0xa mtu_index/l3u_ri_index0:0x0 sm handle [ASIC 0]: 0x7fe5c461c1d8 index1:0xa mtu_index/l3u_ri_index1:0x0 sm handle [ASIC 1]: 0x7fe5c461d688 index2:0xa mtu_index/l3u_ri_index2:0x0 sm handle [ASIC 2]: 0x7fe5c461eb38 index3:0xa mtu_index/l3u_ri_index3:0x0 index4:0xa mtu_index/l3u_ri_index4:0x0 index5:0xa mtu_index/l3u_ri_index5:0x0 Cookie length: 56 00 00 00 00 00 00 00 00 64 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Detailed Resource Information (ASIC#0) ---> ASIC instance 0 = Supervisor ASIC 0, core 0 --snip-- Detailed Resource Information (ASIC#1) ---> ASIC instance 1 = Supervisor ASIC 0, core 1 --snip-- Detailed Resource Information (ASIC#2) ---> ASIC instance 2 = Supervisor ASIC 1, core 0 ---------------------------------------- LEAD_VLAN_ALLOW_SNOOPING_IGMP_OR_MLD_IPV4 value 0 Pass LEAD_VLAN_ALLOW_SNOOPING_IGMP_OR_MLD_IPV6 value 0 Pass LEAD_VLAN_ARP_OR_ND_SNOOPING_ENABLED_IPV4 value 0 Pass LEAD_VLAN_ARP_OR_ND_SNOOPING_ENABLED_IPV6 value 0 Pass LEAD_VLAN_BLOCK_L2_LEARN value 0 Pass LEAD_VLAN_CONTENT_MATCHING_ENABLED value 0 Pass LEAD_VLAN_DEST_MOD_INDEX_TVLAN_LE value 0 Pass LEAD_VLAN_DHCP_SNOOPING_ENABLED_IPV4 value 0 Pass LEAD_VLAN_DHCP_SNOOPING_ENABLED_IPV6 value 0 Pass LEAD_VLAN_ENABLE_SECURE_VLAN_LEARNING_IPV4 value 0 Pass LEAD_VLAN_ENABLE_SECURE_VLAN_LEARNING_IPV6 value 0 Pass LEAD_VLAN_EPOCH value 0 Pass LEAD_VLAN_L2_PROCESSING_STP_TCN value 0 Pass LEAD_VLAN_L2FORWARD_IPV4_MULTICAST_PKT value 0 Pass LEAD_VLAN_L2FORWARD_IPV6_MULTICAST_PKT value 0 Pass LEAD_VLAN_L3_IF_LE_INDEX_PRIO value 1 Pass LEAD_VLAN_L3IF_LE_INDEX value 111 Pass LEAD_VLAN_LOOKUP_VLAN value 10 Pass ------------> MVID 10 = vlan 100 LEAD_VLAN_MCAST_LOOKUP_VLAN value 10 Pass LEAD_VLAN_RIET_OFFSET value 1 Pass LEAD_VLAN_SNOOPING_FLOODING_ENABLED_IGMP_OR_MLD_IPV4 value 0 Pass LEAD_VLAN_SNOOPING_FLOODING_ENABLED_IGMP_OR_MLD_IPV6 value 1 Pass LEAD_VLAN_SNOOPING_PROCESSING_STP_TCN_IGMP_OR_MLD_IPV4 value 0 Pass LEAD_VLAN_SNOOPING_PROCESSING_STP_TCN_IGMP_OR_MLD_IPV6 value 0 Pass LEAD_VLAN_VLAN_CLIENT_LABEL value 0 Pass LEAD_VLAN_VLAN_CONFIG value 0 Pass LEAD_VLAN_VLAN_FLOOD_ENABLED value 0 Pass LEAD_VLAN_VLAN_ID_VALID value 1 Pass LEAD_VLAN_VLAN_LOAD_BALANCE_GROUP value 15 Pass LEAD_VLAN_VLAN_ROLE value 0 Pass LEAD_VLAN_VLAN_FLOOD_MODE_BITS value 3 Pass LEAD_VLAN_LVX_VLAN value 0 Pass LEAD_VLAN_EGRESS_DEJAVU_CANON value 0 Pass LEAD_VLAN_EGRESS_INGRESS_VLAN_MODE value 0 Pass LEAD_VLAN_EGRESS_LOOKUP_VLAN value 0 Pass LEAD_VLAN_EGRESS_SGACL_DISABLED value 3 Pass LEAD_VLAN_EGRESS_VLAN_CLIENT_LABEL value 0 Pass LEAD_VLAN_EGRESS_VLAN_ID_VALID value 1 Pass LEAD_VLAN_EGRESS_VLAN_LOAD_BALANCE_GROUP value 15 Pass LEAD_VLAN_EGRESS_INTRA_POD_BCAST value 0 Pass LEAD_VLAN_EGRESS_INTER_POD_BCAST value 0 Pass LEAD_VLAN_MAX value 0 Pass Detailed Resource Information (ASIC#3) ---> ASIC instance 3 = Supervisor ASIC 1, core 1 --snip-- Detailed Resource Information (ASIC#4) ---> ASIC instance 4 = Supervisor ASIC 2, core 0 --snip- Detailed Resource Information (ASIC#5) ---> ASIC instance 5 = Supervisor ASIC 2, core 1 --snip--
Spanning Tree-programma
C9400#show spanning-tree vlan 100
VLAN0100
Spanning tree enabled protocol rstp Root ID Priority 32868 Address 20bb.c05e.5300 Cost 4 Port 2473 (Port-channel1) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32868 (priority 32768 sys-id-ext 100) Address 2c5a.0f1c.28c0 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/1 Desg FWD 19 128.1 Shr Gi2/0/11 Desg FWD 4 128.107 P2p Po1 Root FWD 3 128.2473 P2p Peer(STP)
C9400#show etherchannel summary --snip-- Group Port-channel Protocol Ports ------+-------------+-----------+----------------------------------------------- 1 Po1(SU) LACP Gi1/0/13(P) Gi5/0/21(P)
Deze opdrachten geven het overspannen van bomen door voor Port-Channel 1.
C9400#show platform software interface rp active brief Forwarding Manager Interfaces Information Name ID QFP ID ------------------------------------------------------------- Null0 1 0 GigabitEthernet1/0/1 7 0 GigabitEthernet1/0/2 8 0 GigabitEthernet1/0/3 9 0 —snip— Port-channel1 748 0 —snip—
C9400#show platform software fed active vp summary interface if_id 748
if_id vlan_id pvlan_mode pvlan_vlan stp_state vtp pruned Untagged
-------------------------------------------------------------------------------------------------
748 100 trunk 1 forwarding No No
De volgende opdrachten tonen de overspannende hardware-doorvoerstatus voor VLAN 100.
C9400#show platform software fed active vp summary vlan 100
if_id vlan_id pvlan_mode pvlan_vlan stp_state vtp pruned Untagged
-------------------------------------------------------------------------------------------------
--snip--
748 100 trunk 1 forwarding No No
--snip--
C9400#show platform hardware fed active vlan 100 ingress VLAN STP State in hardware vlan id is:: 100 Interfaces in forwarding state: : Gi2/0/11(Tagged), Gi1/0/1(Tagged), Gi1/0/13(Tagged), Gi5/0/21(Tagged) flood list: : Gi2/0/11, Gi1/0/1, Gi1/0/13, Gi5/0/21
C9400#show platform hardware fed active vlan 100 egress VLAN STP State in hardware vlan id is:: 100 Interfaces in forwarding state: : Gi2/0/11(Tagged), Gi1/0/1(Tagged), Gi1/0/13(Tagged), Gi5/0/21(Tagged)
Controleer op stabiliteit in de omspanning. Zorg ervoor dat de meldingen van wijziging van de topologie (TCN) niet vaak worden gezien.
C9400#show spanning-tree vlan 100 detail
VLAN0100 is executing the rstp compatible Spanning Tree protocol
Bridge Identifier has priority 32768, sysid 10, address 2c5a.0f1c.28c0
Configured hello time 2, max age 20, forward delay 15, transmit hold-count 6
Current root has priority 32868, address 2c5a.0f1c.5300
Root port is 2473 (Port-channel1), cost of root path is 4
Topology change flag not set, detected flag not set
Number of topology changes 1 last change occurred 2w6d ago
from Port-channel1
Times: hold 1, topology change 35, notification 2
hello 2, max age 20, forward delay 15
Timers: hello 0, topology change 0, notification 0, aging 300
--snip--
L2-doorsturen
C9400#show etherchannel summary --snip-- Group Port-channel Protocol Ports ------+-------------+-----------+----------------------------------------------- 1 Po1(SU) LACP Gi1/0/13(P) Gi5/0/21(P)
C9400#ping 100.100.900.53 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 100.100.900.53, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 3/4/5 ms
C9400#show mac address-table dynamic vlan 100 Mac Address Table ------------------------------------------- Vlan Mac Address Type Ports ---- ----------- -------- ----- 100 0000.0200.0800 DYNAMIC Gi1/0/1 100 20bb.c05e.5318 DYNAMIC Po1 100 20bb.c05e.5351 DYNAMIC Po1 Total Mac Addresses for this criterion: 3
Software programmeren
In de volgende uitvoervoorbeelden, worden de RP-programma's het FP, de FP-programma's de FED, de FED, vervolgens programma's van de supervisor die ASIC-hardware doorstuurt. De RP-software MAC-ingangen worden opgeslagen als objecten in de doeldatabase en de FP-software MAC-ingangen worden als asynchrone objecten in de doeldatabase opgeslagen.
C9400#show platform software matm rp active mac 20bb.c05e.5351 1 100 ---> 100 = vlan Tbl_Type Tbl_ID MAC_Address Type Ports AOM_ID/OM_PTR MAT_VLAN 100 20bb.c05e.5351 1 1 OM: 0x3700860010
List of Ports: 748
C9400#show platform software interface rp active brief Forwarding Manager Interfaces Information Name ID QFP ID ------------------------------------------------------------- Null0 1 0 GigabitEthernet1/0/1 7 0 GigabitEthernet1/0/2 8 0 GigabitEthernet1/0/3 9 0 —snip— Port-channel1 748 0 —snip—
C9400#show platform software matm fp active mac 20bb.c05e.5351 Tbl_Type Tbl_ID MAC_Address Type Ports AOM_ID/OM_PTR MAT_VLAN 100 20bb.c05e.5351 1 1 6567 created List of Ports: 748
C9400#show platform software object-manager fp active object 6567 Object identifier: 6567 Description: matm mac entry type VLAN, id 100, 20bb.c05e.5351
Status: Done, Epoch: 0, Client data: 0x799633f8
Hardware programmering - Methode 1
C9400#show platform software fed active matm macTable vlan 100
VLAN MAC Type Seq# macHandle siHandle diHandle *a_time *e_time ports 100 2c5a.0f1c.28e1 0X8002 0 0x7fe5c5eaf1c8 0x7fe5c5924f38 0x0 0 0 Vlan100 100 20bb.c05e.5351 0X1 589 0x7fe5c6b03d68 0x7fe5c6865f78 0x7fe51001b458 300 1 Port-channel1 100 0000.0200.0800 0X1 610 0x7fe5c6b07888 0x7fe5c6b076e8 0x7fe5c5972ce8 300 1 GigabitEthernet1/0/1 Total Mac number of addresses:: 3 *a_time=aging_time(secs) *e_time=total_elapsed_time(secs) Type: MAT_DYNAMIC_ADDR 0x1 MAT_STATIC_ADDR 0x2 ---> Type = dynamically learned MAC address entry MAT_CPU_ADDR 0x4 MAT_DISCARD_ADDR 0x8 MAT_ALL_VLANS 0x10 MAT_NO_FORWARD 0x20 MAT_IPMULT_ADDR 0x40 MAT_RESYNC 0x80 MAT_DO_NOT_AGE 0x100 MAT_SECURE_ADDR 0x200 MAT_NO_PORT 0x400 MAT_DROP_ADDR 0x800 MAT_DUP_ADDR 0x1000 MAT_NULL_DESTINATION 0x2000 MAT_DOT1X_ADDR 0x4000 MAT_ROUTER_ADDR 0x8000 MAT_WIRELESS_ADDR 0x10000 MAT_SECURE_CFG_ADDR 0x20000 MAT_OPQ_DATA_PRESENT 0x40000 MAT_WIRED_TUNNEL_ADDR 0x80000 MAT_DLR_ADDR 0x100000 MAT_MRP_ADDR 0x200000 MAT_MSRP_ADDR 0x400000 MAT_LISP_LOCAL_ADDR 0x800000 MAT_LISP_REMOTE_ADDR 0x1000000 MAT_VPLS_ADDR 0x2000000
MCHandle programmeerbaarheid
| Acroniem/term |
Definitie |
| VLAN:10 |
MVID 10. VLAN 100 gebruikt intern toegewezen VLAN ID (MVID) 10 in de switch. |
| gpn:1104 |
Mondiaal poortnummer van poortkanaal 1. |
| mac:0x20bc05e5351 |
MAC-adres 20b.c05e.5351 |
Dit is een MacHandle Programming uitvoervoorbeeld:
C9400#show platform hardware fed active fwd-asic abstraction print-resource-handle 0x7fe5c6b03d68 1 Handle:0x7fe5c6b03d68 Res-Type:ASIC_RSC_HASH_TCAM Res-Switch-Num:0 Asic-Num:255 Feature-ID:AL_FID_L2 Lkp-ftr-id:LKP_FEAT_L2_SRC_MAC_VLAN ref_count:1 priv_ri/priv_si Handle: (nil)Hardware Indices/Handles: handle [ASIC: 0]: 0x7fe5c6aed898 handle [ASIC: 1]: 0x7fe5c6b00fd8 handle [ASIC: 2]: 0x7fe5c6858208 Features sharing this resource:Cookie length: 12 5e c0 bb 20 51 53 0a 80 07 00 00 00 Detailed Resource Information (ASIC#0) ---------------------------------------- Number of HTM Entries: 1
Entry 0: (handle 0x7fe5c6aed898) Abs_hash_index: 294 KEY - vlan:10 mac:0x20bbc05e5351 l3_if:0 gpn:1104 epoch:0 static:0 flood_en: 0 vlan_lead_wless_flood_en: 0 client_home_asic: 0 MASK - vlan:0 mac:0x0 l3_if:0 gpn:0 epoch:0 static:0 flood_en:0 vlan_lead_wless_flood_en: 0 client_home_asic: 0 SRC_AD - need_to_learn:0 lrn_v:0 catchall:0 static_mac:0 chain_ptr_v:0 chain_ptr: 0 static_entry_v:0 auth_state:0 auth_mode:0 auth_behavior_tag:0 traf_m:0 is_src_ce:0 DST_AD - si:0xcd bridge:0 replicate:0 blk_fwd_o:0 v4_rmac:0 v6_rmac:0 catchall:0 ign_src_lrn:0 port_mask_o:0 afd_cli_f:0 afd_lbl:0 prio:3 dest_mod_idx:0 destined_to_us:0 pv_trunk:1 smr:0 Detailed Resource Information (ASIC#1) --snip-- Detailed Resource Information (ASIC#2) --snip--
C9400#show platform software fed active vlan 100 VLAN Fed Information Vlan Id IF Id LE Handle STP Handle L3 IF Handle SVI IF ID MVID --------------------------------------------------------------------------------------------------------------- 100 0x0000000000420011 0x00007fe5c4616ef8 0x00007fe5c4617778 0x00007fe5c50dac28 0x00000000000002ea 10
C9400#show platform software fed active ifm mappings etherchannel Mappings Table Chan Interface IF_ID ---------------------------------------------------- 1 Port-channel1 0x000002ec --snip--
C9400#show platform software fed active ifm if-id 0x000002ec <-- IF_ID from previous output Interface IF_ID : 0x00000000000002ec Interface Name : Port-channel1 Interface Block Pointer : 0x7fe5c685df98 Interface State : READY Interface Status : ADD, UPD Interface Ref-Cnt : 5 Interface Type : ETHERCHANNEL Port Type : SWITCH PORT Channel Number : 1 SNMP IF Index : 720 Port Handle : 0x50002f6 #Of Active Ports : 2 Base GPN : 1104 Index[2] : 0000000000000013 Index[3] : 000000000000008f Port Information Handle ............ [0x50002f6] Type .............. [L2-Ethchannel] Identifier ........ [0x2ec] Unit .............. [1] Port Logical Subblock L3IF_LE handle .... [0x0] Num physical port . [2] GPN Base .......... [1104] --snip--
C9400#show platform software fed active ifm mappings gpn Mappings Table GPN Interface IF_ID ---------------------------------------------------------------- 101 GigabitEthernet1/0/1 0x00000007 102 GigabitEthernet1/0/2 0x00000008 103 GigabitEthernet1/0/3 0x00000009 --snip--
Programmeerprogramma
| Acroniem/term |
Definitie |
||
| siHandle |
Station Index Handle. Het pakket herschrijft informatie (RI = Herschrijfindex) en uitgaande interface-informatie (DI = Destination Index). |
||
| Dynamic Bitmap voor dual core op Single Supervisor ASIC: |
|||
| Acroniem/term |
Definitie |
||
| Lokale ASIC (LD = lokale gegevens) |
Bestemming op dezelfde ASIC, dezelfde kern als bron. |
||
| Core-kopie (CD = Core Data |
Bestemming op dezelfde ASIC, een andere kern. |
||
| Afstandsbediening (RD = afstandsgegevens) |
Bestemming op een andere ASIC. |
||
C9400#show platform hardware fed active fwd-asic abstraction print-resource-handle 0x7fe5c6865f78 1 Handle:0x7fe5c6865f78 Res-Type:ASIC_RSC_SI Res-Switch-Num:255 Asic-Num:255 Feature-ID:AL_FID_L3_UNICAST_IPV4 Lkp-ftr-id:LKP_FEAT_INVALID ref_count:2 priv_ri/priv_si Handle: 0x7fe5c6864938Hardware Indices/Handles: index0:0xcd mtu_index/l3u_ri_index0:0x0 index1:0xcd mtu_index/l3u_ri_index1:0x0 index2:0xcd mtu_index/l3u_ri_index2:0x0 index3:0xcd mtu_index/l3u_ri_index3:0x0 index4:0xcd mtu_index/l3u_ri_index4:0x0 index5:0xcd mtu_index/l3u_ri_index5:0x0 Features sharing this resource:64 (1)] 55 (1)] Cookie length: 56 00 00 00 00 00 00 00 00 64 00 00 00 00 00 00 00 00 00 00 00 07 00 20 bb c0 5e 53 51 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Detailed Resource Information (ASIC#0) ---> ASIC instance 0 = Supervisor ASIC 0, core 0 ---------------------------------------- Station Index (SI) [0xcd] RI = 0x29 -------------------------------> Rewrite index (no MAC rewrite for L2 forwarding)
DI = 0x51c2 -------------------------------> Destination index = outgoing interface stationTableGenericLabel = 0 stationFdConstructionLabel = 0 lookupSkipIdIndex = 0 rcpServiceId = 0 dejaVuPreCheckEn = 0x1 Replication Bitmap: LD RD CD Detailed Resource Information (ASIC#1) ---> ASIC instance 1 = Supervisor ASIC 0, core 1 --snip-- Detailed Resource Information (ASIC#2) ---> ASIC instance 2 = Supervisor ASIC 1, core 0 --snip-- Detailed Resource Information (ASIC#3) ---> ASIC instance 3 = Supervisor ASIC 1, core 1 --snip-- Detailed Resource Information (ASIC#4) ---> ASIC instance 4 = Supervisor ASIC 2, core 0 --snip-- Detailed Resource Information (ASIC#5) ---> ASIC instance 5 = Supervisor ASIC 2, core 1 --snip--
C9400#show platform hardware fed active fwd-asic resource asic all destination-index range 0x51c2 0x51c2 ASIC#0: --snip-- ASIC#1: --snip-- ASIC#2: -------------------------> ASIC Instance 2 = Supervisor ASIC 1, core 0 Destination Index (DI) [0x51c2] portMap = 0x00000000 00001000 ---> binary 0001 0000 0000 0000 = Port 12 (see next command output) cmi1 = 0 (read right to left, zero based) rcpPortMap = 0 CPU Map Index (CMI) [0] ctiLo0 = 0 ctiLo1 = 0 ctiLo2 = 0 cpuQNum0 = 0 cpuQNum1 = 0 cpuQNum2 = 0 npuIndex = 0 stripSeg = 0 copySeg = 0 ASIC#3: -------------------------> ASIC instance 3 = Supervisor ASIC 1, core 1 Destination Index (DI) [0x51c2] portMap = 0x00000000 00100000 ---> binary 0001 0000 0000 0000 0000 0000 = Port 20 (see next command output) cmi1 = 0 (read right to left, zero based) rcpPortMap = 0 CPU Map Index (CMI) [0] ctiLo0 = 0 ctiLo1 = 0 ctiLo2 = 0 cpuQNum0 = 0 cpuQNum1 = 0 cpuQNum2 = 0 npuIndex = 0 stripSeg = 0 copySeg = 0 ASIC#4: --snip-- ASIC#5: --snip--
C9400#show platform software fed active ifm mappings Interface IF_ID Inst Asic Core Port SubPort Mac Cntx LPN GPN Type Active GigabitEthernet1/0/1 0x7 2 1 0 0 0 4 4 1 101 NIF Y GigabitEthernet1/0/2 0x8 2 1 0 1 1 4 4 2 102 NIF Y --snip-- GigabitEthernet1/0/13 0x13 2 1 0 12 4 0 0 13 1105 NIF Y --snip-- GigabitEthernet5/0/21 0x8f 3 1 1 20 4 5 5 21 1104 NIF Y --snip--
C9400#show etherchannel summary --snip-- Group Port-channel Protocol Ports ------+-------------+-----------+----------------------------------------------- 1 Po1(SU) LACP Gi1/0/13(P) Gi5/0/21(P)
Er is geen verwachte MAC-herschrijfinformatie omdat dit een Layer 2 MAC-doorvoeringang is.
C9400#show platform hardware fed active fwd-asic resource asic all rewrite-index range 0x29 0x29 1 ASIC#0: Rewrite Data Table Entry, ASIC#:0, rewrite_type:1, RI:41 ---> dec 41 = hex 0x29 MAC Addr: MAC Addr: 20:bb:c0:5e:53:51, L3IF LE Index 111 ASIC#1: Rewrite Data Table Entry, ASIC#:1, rewrite_type:1, RI:41 MAC Addr: MAC Addr: 20:bb:c0:5e:53:51, L3IF LE Index 111 ASIC#2:
--snip--
ASIC#3:
--snip--
ASIC#4:
--snip--
ASIC#5:
--snip--
C9400#show mac address-table address 20bb.c05e.5351
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
100 20bb.c05e.5351 DYNAMIC Po1
Total Mac Addresses for this criterion: 1
Dihandvatprogramma
| acroniem |
Definitie |
| diHandle |
bestemmingsindex Handle. Dit is de uitgaande interface-informatie. |
C9400#show platform hardware fed active fwd-asic abstraction print-resource-handle 0x7fe51001b458 1 Handle:0x7fe51001b458 Res-Type:ASIC_RSC_DI Res-Switch-Num:0 Asic-Num:255 Feature-ID:AL_FID_INVALID Lkp-ftr-id:LKP_FEAT_INVALID ref_count:21 priv_ri/priv_si Handle: (nil)Hardware Indices/Handles: index0:0x51c2 mtu_index/l3u_ri_index0:0x0 index1:0x51c2 mtu_index/l3u_ri_index1:0x0 index2:0x51c2 mtu_index/l3u_ri_index2:0x0 index3:0x51c2 mtu_index/l3u_ri_index3:0x0 index4:0x51c2 mtu_index/l3u_ri_index4:0x0 index5:0x51c2 mtu_index/l3u_ri_index5:0x0 Features sharing this resource:Cookie length: 8 01 00 00 00 c2 51 00 00 Detailed Resource Information (ASIC#0) --snip-- Detailed Resource Information (ASIC#1) --snip-- Detailed Resource Information (ASIC#2) ---> ASIC Instance 2 = Supervisor ASIC 1, core 0 ---------------------------------------- Destination Index (DI) [0x51c2] portMap = 0x00000000 00001000 -------------> binary 0001 0000 0000 0000 = Port 12 (see next command output) cmi1 = 0 (read right to left, zero based) rcpPortMap = 0 CPU Map Index (CMI) [0] ctiLo0 = 0 ctiLo1 = 0 ctiLo2 = 0 cpuQNum0 = 0 cpuQNum1 = 0 cpuQNum2 = 0 npuIndex = 0 stripSeg = 0 copySeg = 0
Detailed Resource Information (ASIC#3) ---> ASIC Instance 3 = Supervisor ASIC 1, core 1 ---------------------------------------- Destination Index (DI) [0x51c2] portMap = 0x00000000 00100000 ---> binary 0001 0000 0000 0000 0000 0000 = Port 20 (see next command output) cmi1 = 0 (read right to left, zero based) rcpPortMap = 0 CPU Map Index (CMI) [0] ctiLo0 = 0 ctiLo1 = 0 ctiLo2 = 0 cpuQNum0 = 0 cpuQNum1 = 0 cpuQNum2 = 0 npuIndex = 0 stripSeg = 0 copySeg = 0
Detailed Resource Information (ASIC#4) --snip-- Detailed Resource Information (ASIC#5) --snip--
C9400#show platform software fed active ifm mappings
Interface IF_ID Inst Asic Core Port SubPort Mac Cntx LPN GPN Type Active GigabitEthernet1/0/1 0x7 2 1 0 0 0 4 4 1 101 NIF Y GigabitEthernet1/0/2 0x8 2 1 0 1 1 4 4 2 102 NIF Y --snip-- GigabitEthernet1/0/13 0x13 2 1 0 12 4 0 0 13 1105 NIF Y --snip-- GigabitEthernet5/0/21 0x8f 3 1 1 20 4 5 5 21 1104 NIF Y --snip--
C9400#show etherchannel summary --snip-- Group Port-channel Protocol Ports ------+-------------+-----------+----------------------------------------------- 1 Po1(SU) LACP Gi1/0/13(P) Gi5/0/21(P)
Hardware-programmering - Methode 2
| Acroniem/term |
Definitie |
| VLAN:10 |
MVID 10. VLAN 100 gebruikt intern toegewezen VLAN ID (MVID) 10 in de switch. |
| gpn:1104 |
Mondiaal poortnummer van poortkanaal 1. |
| mac:0x20bc05e5351 |
MAC-adres 20b.c05e.5351 |
Hardware programmeermethode 2, voorbeelduitvoer:
C9400#show platform hardware fed active matm macTable vlan 100 --snip-- HEAD: MAC address 20bb.c05e.5351 in VLAN 100 KEY: vlan 10, mac 0x20bbc05e5351, l3_if 0, gpn 1104, epoch 0, static 0, flood_en 0, vlan_lead_wless_flood_en 0, client_home_asic 0 MASK: vlan 0, mac 0x0, l3_if 0, gpn 0, epoch 0, static 0, flood_en 0, vlan_lead_wless_flood_en 0, client_home_asic 0 SRC_AD: need_to_learn 0, lrn_v 0, catchall 0, static_mac 0, chain_ptr_v 0, chain_ptr 0, static_entry_v 0, auth_state 0, auth_mode 0, traf_mode 0, is_src_ce 0 DST_AD: si 0xc7, bridge 0, replicate 0, blk_fwd_o 0, v4_mac 0, v6_mac 0, catchall 0, ign_src_lrn 0, port_mask_o 0, afd_cli_f 0, afd_lbl 0, priority 3, dest_mod_idx 0, destined_to_us 0, pv_trunk 1
--snip--
C9400#show platform software fed active vlan 100 VLAN Fed Information Vlan Id IF Id LE Handle STP Handle L3 IF Handle SVI IF ID MVID --------------------------------------------------------------------------------------------------------------- 100 0x0000000000420011 0x00007fe5c4616ef8 0x00007fe5c4617778 0x00007fe5c50dac28 0x00000000000002ea 10
C9400#show platform software fed active ifm mappings etherchannel Mappings Table Chan Interface IF_ID ---------------------------------------------------- 1 Port-channel1 0x000002ec --snip--
C9400#show platform software fed active ifm if-id 0x000002ec Interface IF_ID : 0x00000000000002ec Interface Name : Port-channel1 Interface Block Pointer : 0x7fe5c685df98 Interface State : READY Interface Status : ADD, UPD Interface Ref-Cnt : 5 Interface Type : ETHERCHANNEL Port Type : SWITCH PORT Channel Number : 1 SNMP IF Index : 720 Port Handle : 0x50002f6 #Of Active Ports : 2 Base GPN : 1104 Index[2] : 0000000000000013 Index[3] : 000000000000008f Port Information Handle ............ [0x50002f6] Type .............. [L2-Ethchannel] Identifier ........ [0x2ec] Unit .............. [1] Port Logical Subblock L3IF_LE handle .... [0x0] Num physical port . [2] GPN Base .......... [1104] --snip--
C9400#show platform software fed active ifm mappings gpn Mappings Table GPN Interface IF_ID ---------------------------------------------------------------- 101 GigabitEthernet1/0/1 0x00000007 102 GigabitEthernet1/0/2 0x00000008 103 GigabitEthernet1/0/3 0x00000009 --snip--
TCAM-toepassingen
Controleer het TCAM-gebruik voor de MAC-adreangen op elke ASIC-instantie van de supervisor om er zeker van te zijn dat de switch geen TCAM-ruimte meer heeft om items in hardware op te slaan.
C9400show platform hardware fed active fwd-asic resource tcam utilization CAM Utilization for ASIC Instance [0] --snip-- CAM Utilization for ASIC Instance [1] --snip-- CAM Utilization for ASIC Instance [2] --snip-- CAM Utilization for ASIC Instance [3]---> ASIC instance 3 = Supervisor ASIC 1, Core 1
Table Max Values Used Values -------------------------------------------------------------------------------- Unicast MAC addresses 65536/1024 13/1 -------------> prefix/mask IGMP and Multicast groups 16384/1024 0/7 L2 Multicast groups 16384/1024 1/9 Directly or indirectly connected routes 49152/65536 0/0 NAT/PAT SA address and Port 0 0 QoS Access Control Entries 18432 34 Security Access Control Entries 18432 0 Ingress Netflow ACEs 1024 0 Policy Based Routing ACEs 2048 9 Egress Netflow ACEs 2048 8 Input Microflow policer ACEs 0 0 Output Microflow policer ACEs 0 0 Flow SPAN ACEs 1024 13 Control Plane Entries 1024 0 Tunnels 1024 0 Lisp Instance Mapping Entries 1024 0 Input Security Associations 512 3 Output Security Associations and Policies 512 0 SGT_DGT 8192/512 0/0 CLIENT_LE 4096/256 2/0 INPUT_GROUP_LE 1024 0 OUTPUT_GROUP_LE 1024 0 Macsec SPD 256 0 CAM Utilization for ASIC Instance [4] --snip-- CAM Utilization for ASIC Instance [5] --snip--
Succesvolle hardwareprogrammeering
Alle functies (of het een mac-adres, een interface, een VLAN enzovoort is) worden opgeslagen in de objectdatabase en geprogrammeerd in de hardware als objecten.
De RP-programma's voor het KP, de KP-programma's voor de FED en de FED, en daarna ten slotte programma's voor het doorsturen van ASIC-hardware door de toezichthouder. RP software-ingangen worden als objecten in de doeldatabase opgeslagen en de FP software-ingangen worden als asynchrone objecten in de doeldatabase opgeslagen.
Wanneer de FED de FED programma's uitvoert (die op hun beurt de supervisor doorstuurt ASIC), stuurt de FED een bevestiging terug naar het KP. Het KP zendt het vervolgens naar de RP om aan te geven dat de hardwareprogrammering succesvol is voltooid. Als de FED-hardwareprogrammering ontbreekt of niet correct is, kunt u deze volgende opdracht gebruiken om problemen en/of kennisgevingen te controleren.
C9400#show platform software object-manager fp active statistics Forwarding Manager Asynchronous Object Manager Statistics Object update: Pending-issue: 0, Pending-acknowledgement: 0 Batch begin: Pending-issue: 0, Pending-acknowledgement: 0 Batch end: Pending-issue: 0, Pending-acknowledgement: 0 Command: Pending-acknowledgement: 0 Total-objects: 3269 Stale-objects: 0 Resolve-objects: 0 Error-objects: 0 Paused-types: 0
Als de vorige opdracht niet-nulobjecten in hangende uitgiftestatus toont, gebruik deze opdracht om het betrokken objectnummer te vinden:
C9400#show platform software object-manager fp active pending-issue-update
Gebruik dan deze opdracht om het vast proces te bepalen dat aan het objectnummer is gekoppeld:
C9400#show platform software object-manager fp active object {object#}
Aan de kant van RP, gebruik deze opdracht om hangend (Del Pend) wissen te controleren voor een object dat het FP niet erkende.
C9400#show platform software object-manager rp active object-type-info
Object type Name Count Del Pend Layer ------------------------------------------------------------------------------ CC cc 5 0 2 SPA spa 0 0 4 PORT_DPIDB port_dpidb 164 0 10 CHANNEL_DPIDB channel_dpidb 0 0 12 VIRTUAL_DPIDB virtual_dpidb 503 0 13 SW_DPIDB sw_dpidb 0 0 17 VLAN vlan 0 0 19
--snip--
Gezondheidscontrole
Verkeer en beleid van besturingsplane
Controleer of de CoPP (Control Plane Policy) in hardware-UADP 2.0 is gedaald voor verkeer dat is gericht op software-CPU. Dit kan van invloed zijn op het leren van MAC en de stabiliteit van de Spanning-boom.
C9400#show policy-map control-plane
Control Plane
Service-policy input: system-cpp-policy
--snip--
Class-map: system-cpp-police-sw-forward (match-any)
0 packets, 0 bytes
5 minute offered rate 0000 bps, drop rate 0000 bps
Match: none
police:
rate 1000 pps, burst 244 packets
conformed 1298 bytes; actions:
transmit
exceeded 0 bytes; actions:
drop
--snip--
Class-map: system-cpp-police-l2-control (match-any)
0 packets, 0 bytes
5 minute offered rate 0000 bps, drop rate 0000 bps
Match: none
police:
rate 500 pps, burst 122 packets
conformed 239197001 bytes; actions:
transmit
exceeded 0 bytes; actions:
drop
--snip--
Class-map: system-cpp-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0000 bps, drop rate 0000 bps
Match: none
police:
rate 1000 pps, burst 244 packets
conformed 0 bytes; actions:
transmit
exceeded 0 bytes; actions:
drop
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0000 bps, drop rate 0000 bps
Match: any
Dezelfde CoPP-uitvoer als het vorige voorbeeld wordt hier in een korter en eenvoudiger om te lezen (gecomprimeerd) formaat weergegeven.
C9400#show platform hardware fed active qos queue stats internal cpu policer
CPU Queue Statistics
============================================================================================
(default) (set) Queue Queue
QId PlcIdx Queue Name Enabled Rate Rate Drop(Bytes) Drop(Frames)
0 11 DOT1X Auth Yes 1000 1000 0 0
1 1 L2 Control Yes 2000 400 0 0
2 14 Forus traffic Yes 1000 1000 0 0
3 0 ICMP GEN Yes 600 600 0 0
4 2 Routing Control Yes 5400 1800 0 0
5 14 Forus Address resolution Yes 1000 1000 0 0
6 0 ICMP Redirect Yes 600 600 0 0
7 16 Unused Yes 1000 1000 0 0
8 4 L2 LVX Cont Pack Yes 1000 1000 0 0
9 16 EWLC Control Yes 1000 1000 0 0
10 16 EWLC Data Yes 1000 1000 0 0
11 13 L2 LVX Data Pack Yes 1000 1000 0 0
12 0 BROADCAST Yes 600 600 0 0
13 10 Learning cache ovfl Yes 100 200 0 0
14 13 Sw forwarding Yes 1000 1000 0 0
15 8 Topology Control Yes 13000 13000 0 0
16 12 Proto Snooping Yes 2000 2000 0 0
17 16 DHCP Snooping Yes 1000 1000 0 0
18 9 Transit Traffic Yes 500 400 0 0
19 10 RPF Failed Yes 100 200 0 0
20 15 MCAST END STATION Yes 2000 2000 0 0
21 13 LOGGING Yes 1000 1000 0 0
22 7 Punt Webauth Yes 1000 1000 0 0
23 10 Crypto Control Yes 100 200 0 0
24 10 Exception Yes 100 200 0 0
25 3 General Punt Yes 200 200 0 0
26 10 NFL SAMPLED DATA Yes 100 200 0 0
27 2 Low Latency Yes 5400 1800 0 0
28 10 EGR Exception Yes 100 200 0 0
29 5 Stackwise Virtual Control No 8000 8000 0 0
30 9 MCAST Data Yes 500 400 0 0
31 10 Gold Pkt Yes 100 200 0 0
* NOTE: CPU queue policer rates are configured to the closest hardware supported value
CPU Queue Policer Statistics
====================================================================
Policer Policer Accept Policer Accept Policer Drop Policer Drop
Index Bytes Frames Bytes Frames
-------------------------------------------------------------------
0 3132 36 0 0
1 239197001 721952 0 0
2 123004776 978818 0 0
3 0 0 0 0
4 0 0 0 0
5 0 0 0 0
6 0 0 0 0
7 0 0 0 0
8 1024 16 0 0
9 0 0 0 0
10 13600 200 0 0
11 0 0 0 0
12 0 0 0 0
13 1298 3 0 0
14 80520 9158 0 0
15 2189268 23733 0 0
16 0 0 0 0
17 0 0 0 0
CPP Classes to queue map
======================================================================================
PlcIdx CPP Class : Queues
--------------------------------------------------------------------------------------
0 system-cpp-police-data : ICMP GEN/BROADCAST/ICMP Redirect/
10 system-cpp-police-sys-data : Learning cache ovfl/Crypto Control/Exception/EGR Exception/NFL SAMPLED DATA/Gold Pkt/RPF Failed/
13 system-cpp-police-sw-forward : Sw forwarding/LOGGING/L2 LVX Data Pack/
9 system-cpp-police-multicast : Transit Traffic/MCAST Data/
15 system-cpp-police-multicast-end-station : MCAST END STATION /
7 system-cpp-police-punt-webauth : Punt Webauth/
1 system-cpp-police-l2-control : L2 Control/
5 system-cpp-police-stackwise-virt-control : Stackwise Virtual Control/
2 system-cpp-police-routing-control : Routing Control/Low Latency/
3 system-cpp-police-control-low-priority : General Punt/
4 system-cpp-police-l2lvx-control : L2 LVX Cont Pack/
8 system-cpp-police-topology-control : Topology Control/
11 system-cpp-police-dot1x-auth : DOT1X Auth/
12 system-cpp-police-protocol-snooping : Proto Snooping/
14 system-cpp-police-forus : Forus Address resolution/Forus traffic/
5 system-cpp-police-stackwise-virt-control : Stackwise Virtual Control/
16 system-cpp-default : DHCP Snooping/Unused/EWLC Control/EWLC Data/
Controleer CPU-puntpad (hardware-UADP 2.0 naar software-CPU) vanuit een CPU-perspectief.
C9400#show platform software infrastructure lsmpi
LSMPI interface internal stats:
enabled=0, disabled=0, throttled=0, unthrottled=0, state is ready
Input Buffers = 8801257
Output Buffers = 5506129
rxdone count = 8801257
txdone count = 5506128
Rx no particletype count = 0
Tx no particletype count = 0
Txbuf from shadow count = 0
No start of packet = 0
No end of packet = 0
Punt drop stats:
Bad version 0
Bad type 0
Had feature header 0
Had platform header 0
Feature header missing 0
Common header mismatch 0
Bad total length 0
Bad packet length 0
Bad network offset 0
Not punt header 0
Unknown link type 0
No swidb 0
Bad ESS feature header 0
No ESS feature 0
No SSLVPN feature 0
No PPP bridge feature 0
Punt For PPP bridge type packets 0
Punt For Us type unknown 0
EPC CP RX Pkt cleansed 0
Punt cause out of range 0
IOSXE-RP Punt packet causes:
42879 Layer2 control and legacy packets
3644168 ARP request or response packets
7584 For-us data packets
1794 Mcast Directly Connected Source packets
1573 Mcast PIM signaling packets
750076 For-us control packets
38058 Layer2 bridge domain data packet packets
3823736 Layer2 control protocols packets
FOR_US Control IPv4 protcol stats:
750076 [proto=0] packets
Packet histogram(500 bytes/bin), avg size in 125, out 126:
Pak-Size In-Count Out-Count
0+: 8228322 5207592
500+: 41355 1717
1000+: 4331 2402
1500+: 35860 20017
Lsmpi11/3 is up, line protocol is up <-- CPU interface
Hardware is LSMPI
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Unknown, Unknown, media type is unknown media type
output flow-control is unsupported, input flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/1500/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
8309868 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 watchdog, 0 multicast, 0 pause input
5231728 packets output, 659535525 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
C9400#show platform software infrastructure lsmpi punt
LSMPI punt statistics
Total packets consumed: 876
Total packets forwarded: 8468766
First frag packets: 0
Total packets consumed & forwarded: 0
Cause Total Total Length Dot1q encap Other SKB
consumed forwarded error exceeded linktype invalid
MPLS ICMP Can't Fragment 0 0 0 0 0 0
IPv4 Options 0 0 0 0 0 0
Layer2 control and legacy 0 0 0 0 0 0
PPP Control 0 0 0 0 0 0
CLNS IS-IS Control 0 0 0 0 0 0
HDLC keepalives 0 0 0 0 0 0
--snip--
Controleer CPU-injectiepad (software-CPU naar hardwaresupervisor) vanuit een CPU-perspectief.
C9400#show platform software infrastructure inject Statistics for L3 injected packets: 5233473 total inject pak, 3 failed 0 sent, 859329 prerouted 0 non-CEF capable, 855296 non-unicast 859826 IP, 0 IPv6 0 MPLS, 0 Non-IP Tunnel 0 UDLR tunnel, 0 P2MP replicated mcast 0 Non-IP Fastswitched over Tunnel, 4373497 legacy pak path 0 Other packet 0 IP fragmented 644 normal, 391 nexthop 858788 adjacency, 150 feature 0 undefined 3 pak find no adj, 0 no adj-id 137322 sb alloc, 856085 sb local 0 p2mcast failed count 0 p2mcast enqueue fail 0 unicast dhc 0 mobile ip 0 IPv6 NA 0 IPv6 NS 0 Transport failed cases 0 Grow packet buffer per feature packet inject statistics 150 Feature multicast 0 Feature Edge Switching Service 0 Feature Session Border Controller 0 Feature interrupt level 0 Feature use outbound interface 0 Feature interrupt level with OCE 0 Feature ICMPv6 error message 0 Feature Session Border Controller media packet injection 0 Feature Tunnel Ethernet over GRE 0 Feature Secure Socket Layer Virtual Private Network 0 Feature EPC Wireshark injecting packets Statistics for L2 injected packets: 0 total L2 inject pak, 0 failed 0 total BD inject pak, 0 failed 0 total EFP inject pak, 0 failed 0 total VLAN inject pak, 0 failed
Controleer CPU punt/injectiestatistieken vanuit een FED-perspectief (UADP 2.0).
C9400#show platform software fed active lsmpi stat
LSMPI Statistics
-------------------------------------------
Transmit: -----------------------------------> FED transmit = FED (Supervisor) punt to CPU
Packet Count : 8469445
Bytes Count : 1055390613
particle Count : 8951009
particle with App : 7258
Ring Full Error : 0
No Buff Error : 0
TX Ring Free : 2047
TX Ring Busy : 0
TX Ring Size : 2048
TXDone Ring Free : 6816
TXDone Ring Busy : 9567
TXDone Ring Size : 16384
Receive: ---------------------------------> FED receive = CPU inject to FED (Supervisor)
Packet Count : 5450099
Bytes Count : 675084903
Particle Count : 5695697
Particles with App : 4294966854
RX Done Count : 5696139
No SOP : 0
No EOP : 0
Not Enough Buf : 0
Max Not Enough Buf : 0
RX Ring Free : 4095
RX Ring Busy : 0
RX Ring Size : 4096
RXDone Ring Free : 8191
RXDone Ring Busy : 0
RXDone Ring Size : 8192
-------------------------------------------
Controleer het CPU-punt pad (hardware-supervisor naar software-CPU) vanuit een FED-perspectief (supervisor).
C9400#show platform software fed active punt cause summary Statistics for all causes Cause Cause Info Rcvd Dropped ------------------------------------------------------------------------------ 7 ARP request or response 3644168 0 11 For-us data 1524 0 12 Mcast Directly Connected Source 1794 0 25 Mcast PIM signaling 1573 0 55 For-us control 750461 0 58 Layer2 bridge domain data packet 38058 0 96 Layer2 control protocols 3825228 0 ------------------------------------------------------------------------------
Controleer de status van de 31 individuele CPU-wachtrijen vanuit een FED-perspectief (supervisor).
C9400#show platform software fed active cpu-interface queue retrieved dropped invalid hol-block ------------------------------------------------------------------------- Routing Protocol 790844 0 0 0 L2 Protocol 2774488 0 0 0 sw forwarding 0 0 0 0 broadcast 0 0 0 0 icmp 0 0 0 0 icmp redirect 0 0 0 0 logging 0 0 0 0 rpf-fail 1573 0 0 0 DOT1X authentication 0 0 0 0 Forus Traffic 1524 0 0 0 Forus Resolution 3644192 0 0 0 Wireless q5 0 0 0 0 Wireless q1 0 0 0 0 Wireless q2 0 0 0 0 Wireless q3 0 0 0 0 Wireless q4 0 0 0 0 Learning cache 0 0 0 0 Topology control 1198807 0 0 0 Proto snooping 0 0 0 0 BFD Low latency 0 0 0 0 Transit Traffic 0 0 0 0 Multi End station 38058 0 0 0 Health Check 0 0 0 0 Health Check 0 0 0 0 Crypto control 0 0 0 0 Exception 0 0 0 0 General Punt 0 0 0 0 NFL sampled data 0 0 0 0 STG cache 0 0 0 0 EGR exception 0 0 0 0 FSS 0 0 0 0 Multicast data 1794 0 0 0
C9400#show platform software fed active punt cpuq all
Punt CPU Q Statistics
===========================================
—snip—
CPU Q Id : 1
CPU Q Name : CPU_Q_L2_CONTROL
Packets received from ASIC : 2669864 -----------> Packets received by the FED process from the Supervisor forwarding ASICs
Send to IOSd total attempts : 2669864 -----------> Packets sent from the FED process to IOSd
Send to IOSd failed count : 0
RX suspend count : 0
RX unsuspend count : 0
RX unsuspend send count : 0
RX unsuspend send failed count : 0
RX consumed count : 0
RX dropped count : 0
RX non-active dropped count : 0
RX conversion failure dropped : 0
RX INTACK count : 2243784
RX packets dq'd after intack : 5074
Active RxQ event : 2243785
RX spurious interrupt : 322266
CPU Q Id : 2
CPU Q Name : CPU_Q_FORUS_TRAFFIC
Packets received from ASIC : 1524
Send to IOSd total attempts : 1524
Send to IOSd failed count : 0
RX suspend count : 0
RX unsuspend count : 0
RX unsuspend send count : 0
RX unsuspend send failed count : 0
RX consumed count : 0
RX dropped count : 0
RX non-active dropped count : 0
RX conversion failure dropped : 0
RX INTACK count : 1347
RX packets dq'd after intack : 8
Active RxQ event : 1347
RX spurious interrupt : 38
—snip—
Controleer het CPU-injectiepad (software-CPU naar hardwaresupervisor) vanuit een FED-perspectief (supervisor).
C9400#show platform software fed active inject cause summary Statistics for all causes Cause Cause Info Rcvd Dropped ------------------------------------------------------------------------------ 1 L2 control/legacy 4331682 0 2 QFP destination lookup 290 0 3 QFP IPv4/v6 nexthop lookup 391 0 7 QFP adjacency-id lookup 859393 265 8 Mcast specific inject packet 150 0 12 ARP request or response 601 0 ------------------------------------------------------------------------------
Controleer de status van de 2 afzonderlijke CPU-injectiegrenzen vanuit een FED-perspectief (UADP 2.0).
C9400#show platform software fed active inject cpuq all Inject CPU Q Statistics =========================================== CPU Q Id : 0 CPU Q Name : TX_CPUQ_PRIO_LOW ---> low priority CPU inject queue Packets received from IOSd : 168342 Enq to pkt driver total attempts : 168277 Enq to pkt driver failed count : 0 Count of TX CMPL received : 168277 TX suspend count : 0 TX unsuspend count : 0 TX dropped count : 265 TX punted count : 0 TX App enq failed : 0 CPU Q Id : 7 CPU Q Name : TX_CPUQ_PRIO_HI ---> high priority CPU inject queue Packets received from IOSd : 5024664 Enq to pkt driver total attempts : 5024664 Enq to pkt driver failed count : 0 Count of TX CMPL received : 5024664 TX suspend count : 0 TX unsuspend count : 0 TX dropped count : 0 TX punted count : 0 TX App enq failed : 0 Stats for all txq: --------------------------------------------- TX chunk malloc fail count : 0 ---------------------------------------------
Statistieken voor MAC-tabel
C9400#show platform software fed active matm stats MATM counters Total non-cpu mac entries : 10 Mac Learn SPI Msg Count : 0 Mac Learn SPI Err Count : 0 Mac Delete SPI Msg Count : 0 Mac Delete SPI Err Count : 0 Mac Learn Count : 967 Mac Add Count : 989 Mac AL add Count : 971 Mac Del Count : 957 Mac AL Del Count : 961 Mac Move Count : 2 ---> MAC moves between interfaces (see details above) Mac AL Move Count : 0 Mac Clear Count : 0 Mac Del all count : 6 Mac table create Count : 9 Mac VP event Count : 5 Mac Update info Count : 0 Mac Vlan age config Event Count : 0 Mac Vlan Link Event Count : 6 Mac SVI linkEvent Count : 3 Mac Bsync Event Count : 0 Mac Isync Event Count : 0 Mac Recon Start Count : 0 Mac Recon Event Count : 0 Mac IFM event Count : 75 Mac FEC Event Count : 0 Mac Aging Tick Count : 0 Mac Retry event Count : 0 Mac Hw Update Err Count : 0 Mac In retryQ Count : 0
C9400#configure terminal C9400(config)#mac address-table notification ? change Enable/Disable MAC Notification feature on the switch mac-move Enable Mac Move Notification threshold Configure L2 Table monitoring C9400(config)#mac address-table notification mac-move ---> enabled by default, syslog generated for any MAC move (show logging) C9400(config)#mac address-table notification change ? history-size Number of MAC notifications to be stored interval Interval between the MAC notifications <cr> <cr> C9400(config)#mac address-table notification change ---> disabled by default
C9400#show mac address-table notification mac-move MAC Move Notification: enabled
C9400#show mac address-table notification change
MAC Notification Feature is Enabled on the switch Interval between Notification Traps : 1 secs Number of MAC Addresses Added : 0 Number of MAC Addresses Removed : 0 Number of Notifications sent to NMS : 0 Maximum Number of entries configured in History Table : 1 Current History Table Length : 0 MAC Notification Traps are Disabled History Table contents ----------------------
UADP 2.0 Exceptiefjes
Deze opdracht specificeert om het even welke redenen dat een UADP 2.0 die ASIC doorstuurt een pakket laat vallen:
C9400#show platform hardware fed active fwd-asic drops exceptions
****EXCEPTION STATS ASIC INSTANCE 0 (asic/core 0/0)**** ================================================================================= Asic/core | NAME | prev | current | delta ================================================================================= 0 0 NO_EXCEPTION 0 0 0 0 0 IPV4_CHECKSUM_ERROR 0 0 0 0 0 ROUTED_AND_IP_OPTIONS_EXCEPTION 0 0 0 0 0 CTS_FILTERED_EXCEPTION 0 0 0 0 0 SIA_TTL_ZERO 0 0 0 0 0 ALLOW_NATIVE_EXCEPTION_COUNT 0 0 0 0 0 ALLOW_DOT1Q_EXCEPTION_COUNT 0 0 0 0 0 ALLOW_PRIORITY_TAGGED_EXCEPTION_COUNT 0 0 0 0 0 ALLOW_UNKNOWN_ETHER_TYPE_EXCEPTION 0 0 0 0 0 IP_SOURCE_GUARD_VIOLATION 0 0 0 0 0 SECURE_L3IF_LEARNING_VIOLATION 0 0 0 0 0 AUTH_DRIVEN_DROP 0 0 0 0 0 VLAN_LOADBALANCE_GROUP_DENY 0 0 0 0 0 RPF_UNICAST_FAIL 0 0 0 0 0 RPF_UNICAST_FAIL_SUPPRESS 0 0 0 0 0 RPF_UNICAST_CHECK_INCOMPLETE 0 0 0 0 0 RPF_MULTICAST_FAIL 0 0 0 0 0 PKT_DROP_COUNT 0 0 0 0 0 SOURCE_ROUTE_EXCEPTION 0 0 0 0 0 IGR_MISC_FATAL_ERROR 0 0 0 0 0 BLOCK_FORWARD 0 0 0 0 0 POLICER_DROP 0 0 0 0 0 DENY_ROUTE 0 0 0 0 0 DENY_BRIDGE 0 0 0 0 0 STATIC_MAC_VIOLATION 0 0 0 0 0 STATIC_IP_VIOLATION 0 0 0 0 0 FPM_DROP_PACKET 0 0 0 0 0 IGR_EXCEPTION_L4_ERROR 0 0 0 0 0 IGR_EXCEPTION_L5_ERROR 0 0 0 0 0 IGR_EXCEPTION_HARDWARE_PARSE_EXCEPTION 0 0 0 0 0 IGR_EXCEPTION_INVALID_VLAN_DROP 0 0 0 0 0 IGR_EXCEPTION_31 0 0 0 0 0 FRAGMENTING_IPV4_WITH_OPTIONS 0 0 0 0 0 FRAGMENTING_IPV6_WITH_EXTENSIONS 0 0 0 0 0 ICMP_REDIRECT 0 0 0 0 0 MTU_FAIL_PUNT_TO_CPU_NO_IP_UNREACHABLE 0 0 0 0 0 LINK_LOCAL_CHECK_FAIL_NO_IP_UNREACHABLE 0 0 0 0 0 IP_UNICAST_TTL_REACHED_ZERO 0 0 0 0 0 MISC_FATAL_ERROR 0 0 0 0 0 STP_OR_FLEXLINK_DROP 0 0 0 0 0 PROTECTED_PORT_DROP 0 0 0 0 0 PVLAN_ISOLATED_CHECK_FAILED 0 0 0 0 0 PVLAN_COMMUNITY_CHECK_FAILED 0 0 0 0 0 DEJA_VU_CHECK_FAILED 0 0 0 0 0 NOT_VLAN_LOAD_BALANCE_GROUP_ALLOWED 0 0 0 0 0 RSPAN_DROP 0 0 0 0 0 SPLIT_HORIZON_DROP 0 0 0 0 0 SYSTEM_TTL_DROP 0 0 0 0 0 PRUNED 0 0 0 0 0 DENY_NO_IP_UNREACHABLE 0 0 0 0 0 IP_MULTICAST_TTL_REACHED_ZERO 0 0 0 0 0 MTU_FAIL_DROP_BRIDGED 0 0 0 0 0 MTU_FAIL_DROP_BRIDGED_IP_ROUTED 0 0 0 0 0 MTU_FAIL_ERSPAN 0 0 0 0 0 LINK_LOCAL_CHECK_FAIL_L3M_VALID 0 0 0 0 0 DENY_NOT_NO_IP_UNREACHABLE 0 0 0 0 0 MTU_FAIL_PUNT_TO_CPU_NOT_NO_IP_UNREACHABLE 0 0 0 0 0 LINK_LOCAL_CHECK_FAIL_NOT_NO_IP_UNREACHABLE 0 0 0 0 0 COPY_TO_CPU 0 0 0 0 0 EGR_L3_ERROR 0 0 0 0 0 EGR_L4_ERROR 0 0 0 0 0 EGR_L5_ERROR 0 0 0 0 0 EGR_HARDWARE_PARSE_EXCEPTION 0 0 0 0 0 EGR_SHOW_FORWARD_DROP 0 0 0 ****EXCEPTION STATS ASIC INSTANCE 1 (asic/core 0/1)**** ================================================================================= Asic/core | NAME | prev | current | delta ================================================================================= 0 1 NO_EXCEPTION 13168 16679 3511 0 1 IPV4_CHECKSUM_ERROR 0 0 0 0 1 ROUTED_AND_IP_OPTIONS_EXCEPTION 81 103 22
--snip--
Supervisor Statistics - Supervisor to Line Card Data Path
Controleer de actieve supervisor UADP 2.0 die ASIC statistieken door zal sturen die met een specifieke interface van het voorpaneel worden geassocieerd. In dit voorbeeld wordt de interface Gig1/0/13 gebruikt.
Uitloopvoorbeeld:
- Controleer welke interfaces op de lijnkaart deel uitmaken van dezelfde poortgroep.
- Elke poortgroep deelde 8 Gbps bandbreedte van de lijnkaartstub ASIC naar de supervisor die ASIC doorstuurt.
- Elke poortgroep wordt geassocieerd met één van de SLI (System Link Interface) op de lijnkaartstap ASIC naar de supervisor die ASIC doorstuurt.
C9400#show platform hardware cman fp active data-path 1 13 detail ---> Slot 1, interface 13
showing cman data-path for frontpanel 1/0/13 fp_portmap.xml: ---> Supervisor ASIC 1, core 0 is associated with front panel (fp) interface Gig1/0/13 id 13 asic 1 core 0 port 12 mac 0 subport 4 contextid 0 maxspeed DEV_PORT_SPEED_1G gpn 113 active 1 data path: slot 3 +- ACTIVE_SUP --+ | Sif 0 | | IQS SQS | ---> Supervisor ASIC 1, core 0 on the slot 3 active Supervisor associated with interface Gig1/0/13 | PBC | | AQM | | EQC | | ESM | | RWE | | ASIC 1 | | Core 0 | | Asic Port 12 | | | | (Mac 0) | |Nif_Rx NifTx| +--------------+ ^ | | | | | | V ============================================== Nif MAC 0 Inforation: NifRxByteGroupStats: NifTxByteGroupStats: rxBytes 4495494 txBytes 6499427 NifRxByteDestinationGroupStats: NifTxByteDestinationGroupStats: rxUnicastBytes 1174628 txUnicastBytes 1175536 rxMulticastBytes 3320866 txMulticastBytes 5298482 rxBroadcastBytes 0 txBroadcastBytes 25409 NifRxPortStatusGroupStats: NifTxFrameDestinationGroupStats: rxUnicastFrames 18326 txUnicastFrames 18330 rxMulticastFrames 21387 txMulticastFrames 24834 rxBroadcastFrames 0 txBroadcastFrames 51 rxPauseFrames 0 txPauseFrames 0 rxCos0PauseFrames 0 txCos0PauseFrames 0 rxCos1PauseFrames 0 txCos1PauseFrames 0 rxCos2PauseFrames 0 txCos2PauseFrames 0 rxCos3PauseFrames 0 txCos3PauseFrames 0 rxCos4PauseFrames 0 txCos4PauseFrames 0 rxCos5PauseFrames 0 txCos5PauseFrames 0 rxCos6PauseFrames 0 txCos6PauseFrames 0 rxCos7PauseFrames 0 txCos7PauseFrames 0 rxOamProcessedFrames 0 txOamFrames 0 NifRxPortStatusGroupStats: NifTxPortStatusGroupStats: rxCollisionFragments 0 txLateCollisionFrames 0 rxFcsErrorFrames 0 txsystemFcsErrorFrames 0 rxInvalidOversizeFrames 0 txOversizeFrames 0 rxMacOverrunFrames 0 txMacUnderrunFrames 0 rxIpgViolationFrames 0 txDeferredFrames 0 rxOamDroppedFrames 0 txExcessiveDeferralFrames 0 rxSymbolErrorFrames 0 txOkMultipleCollisionFrames 0 rxValidOversizeFrames 0 txOkSingleCollisionFrames 0 rxValidUndersizeFrames 0 goldFramesTruncated 0 NifRxSizeGroupStats: NifTxSizeGroupStats: rx32768toMtuFrames 0 tx32768toMtuFrames 0 rx16384to32767ByteFrames 0 tx16384to32767ByteFrames 0 rx8192to16383ByteFrames 0 tx8192to16383ByteFrames 0 rx4096to8191ByteFrames 0 tx4096to8191ByteFrames 0 rx2048to4095ByteFrames 0 tx2048to4095ByteFrames 0 rx1519to2047ByteFrames 51 tx1519to2047ByteFrames 0 rx1024to1518ByteFrames 15 tx1024to1518ByteFrames 0 rx512to1023ByteFrames 17 tx512to1023ByteFrames 187 rx256to511ByteFrames 3406 tx256to511ByteFrames 9407 rx128to255ByteFrames 6567 tx128to255ByteFrames 6580 rx65to127ByteFrames 11295 tx65to127ByteFrames 8583 rx64ByteFrames 18362 tx64ByteFrames 18458 ============================================== ----------------------------------------------------> Input queue (Igr = Ingress) IgrPacketCounters: EgrPacketCounters: packetsIn 97777 packetsIn 580324 packetsOut 97777 packetsEnqueueFcd_val 0 packetsDropped 3383 packetsMarkedForDrop 278 fpsSourcedPadErrorCount 0 padErrorPacketsIn 0 igrSourcedPadErrorCount 0 padErrorPacketsOut 0 ============================================== For RWE for core 0: RweTotalEnqStats: packetCount 580324 RweTotalDeqStats: packetCount 580046 FragmentCount 580046 ============================================== For EQC for core 0: EqcTotalEnqStats: Count 580704 EqcTotalDeqStats: Count 580324 ============================================== For aqmRedQueueStats for asic port 12: AqmRedQueueStats: (sum of all queues) ---> Output queue (Aqm = Active queue management) acceptByteCnt0 0 acceptFrameCnt0 0 acceptByteCnt1 6407742 acceptFrameCnt1 43070 acceptByteCnt2 39609 acceptFrameCnt2 395 dropByteCnt0 0 dropFrameCnt0 0 dropByteCnt1 0 dropFrameCnt1 0 dropByteCnt2 0 dropFrameCnt2 0 outOfSoftBufDropByteCnt 0 outOfSoftBufDropFrameCnt 0 maxQebDropByteCnt 0 maxQebDropFrameCnt 0 ============================================== For PBC for core 0: PbcIngressErrorDropCount: PbcEgressErrorDropCount: iCount 0 eS0Count 0 iCount 0 eS1Count 0 PbcCreditCount: PbcEnqFcErrorDropCount: creditCount 64 fCount 0 rwePbcStall 0 ============================================== For local/core 0 Switching: SqsCumulativeStatistics totalEnqStat 1368200 totalDeqStat 1368200 totalDropStat 0 SqsCumulativeStatisticsB totalEnqStat 173449513 totalDeqStat 173449513 totalDropStat 0 ============================================== For local/core 1 Switching: SqsCumulativeStatistics totalEnqStat 890114 totalDeqStat 890114 totalDropStat 0 SqsCumulativeStatisticsB totalEnqStat 105061923 totalDeqStat 105061923 totalDropStat 0 ============================================== For Sif 0 Switching: SifSifPbcCnt0: Count 81302675 SifSifPbcCnt1: Count 58187651 SifRacInsertedCnt: SifRacCopiedCnt: SifRacInsertedCnt[0] 2295051 SifRacCopiedCnt[0] 35850468 SifRacInsertedCnt[1] 1738892 SifRacCopiedCnt[1] 19265491 SifRacInsertedCnt[2] 1666479 SifRacCopiedCnt[2] 23814855 SifRacInsertedCnt[3] 2773364 SifRacCopiedCnt[3] 32727259 SifRacInsertedCnt[4] 3126116 SifRacCopiedCnt[4] 38376676 SifRacInsertedCnt[5] 2066567 SifRacCopiedCnt[5] 22176467 ============================================== For Sif 1 Switching: SifSifPbcCnt0: Count 40956521 SifSifPbcCnt1: Count 40956521 SifRacInsertedCnt: SifRacCopiedCnt: SifRacInsertedCnt[0] 11713808 SifRacCopiedCnt[0] 8615615 SifRacInsertedCnt[1] 8319576 SifRacCopiedCnt[1] 7489596 SifRacInsertedCnt[2] 8816344 SifRacCopiedCnt[2] 7608895 SifRacInsertedCnt[3] 15404080 SifRacCopiedCnt[3] 8717898 SifRacInsertedCnt[4] 16161715 SifRacCopiedCnt[4] 9685735 SifRacInsertedCnt[5] 9745420 SifRacCopiedCnt[5] 7866174
Controleer de stroombeheerstatus vanuit een Supervisor perspectief voor de interface van het voorpaneel. Dit helpt u te identificeren of er opstopping is.
C9400#show platform hardware cman fp active flowcontrol status
slot 1:Port 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 EsmF - - - - - - - - - - - - - - - - - - - - - - - - IqsC - - - - - - - - - - - - - - - - - - - - - - - - Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 EsmF - - - - - - - - - - - - - - - - - - - - - - - - IqsC - - - - - - - - - - - - - - - - - - - - - - - - slot 2: Port 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 EsmF - - - - - - - - - - - - - - - - - - - - - - - - IqsC - - - - - - - - - - - - - - - - - - - - - - - - Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 EsmF - - - - - - - - - - - - - - - - - - - - - - - - IqsC - - - - - - - - - - - - - - - - - - - - - - - - slot 3: Port 01 02 03 04 05 06 07 08 09 10 EsmF - - - - - - - - - - IqsC 01 - - - - - - - - - slot 4: Port 01 02 03 04 05 06 07 08 09 10 EsmF - - - - - - - - - - IqsC - - - - - - - - - - slot 5: Port 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 EsmF - - - - - - - - - - - - - - - - - - - - - - - - IqsC - - - - - - - - - - - - - - - - - - - - 01 - - - Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 EsmF - - - - - - - - - - - - - - - - - - - - - - - - IqsC - - - - - - - - - - - - - - - - - - - - - - - - slot 6: Possibly linecard is not inserted slot 7: Possibly linecard is not inserted
Controleer dat het controleverkeer vanuit een supervisor die ASIC-perspectief doorstuurt tussen de supervisor die ASIC doorstuurt op de actieve supervisor en de lijnkaartstap ASIC op de lijnkaart via de OCI-interfaces stroomt.
C9400#show platform hardware cman fp active oci status
processing oci information:
chassis_type: 1
sup slot: 4
sup num oci ports: 8
slot_id 1 : oci_enable Enabled Link Status 0 (UP)
asic_id 1 core_id 0 oci_port 3 mac_id 0
NruRxByteGroupStats: rxBytes 417829462717812 NruTxByteGroupStats: txBytes 588911286106332
slot_id 2 : oci_enable Enabled Link Status 0 (UP)
asic_id 0 core_id 0 oci_port 1 mac_id 1
NruRxByteGroupStats: rxBytes 417938235716344 NruTxByteGroupStats: txBytes 588917607864892
slot_id 5 : oci_enable Enabled Link Status 0 (UP)
asic_id 1 core_id 0 oci_port 4 mac_id 1
NruRxByteGroupStats: rxBytes 53195855717244 NruTxByteGroupStats: txBytes 588915422236932
slot_id 6 : oci_enable Enabled Link Status 1 (DOWN)
asic_id 2 core_id 0 oci_port 6 mac_id 0
NruRxByteGroupStats: rxBytes 0 NruTxByteGroupStats: txBytes 0
slot_id 7 : oci_enable Enabled Link Status 1 (DOWN)
asic_id 0 core_id 0 oci_port 2 mac_id 2
NruRxByteGroupStats: rxBytes 0 NruTxByteGroupStats: txBytes 0
Statistieken voor lijnkaart - supervisor naar lijnkaartpad
Controleer de ASIC-statistieken van de lijnkaartkaart die bij een specifieke frontpaneelinterface zijn aangesloten. In dit voorbeeld is de focus van de interface Gig1/0/13.
Uitloopvoorbeeld:
-
Packets die worden ontvangen van Gig 1/0/13 gaan de netwerkinterface in die poort en voortgang door IQS naar de stapelinterface ontvangt.
-
Van daaruit gaat een pakket ofwel de stapel interface naar een andere supervisor ASIC uit, of komt terug door de SQL, AQM, EQC, ESM, RWE, en dan gaat de Network Interface verzenden van Gig 1/0/13.
-
Packets die vanuit andere ASICs-interfaces van supervisor worden verzonden en die uit Gig 1/0/13 geraken, gaan Sif in en gaan dan door SQL, AQM, EQC, ESM, RWE en dan de NifTx van Gig 1/0/13.
-
Voor AQM zijn er 8 TX-wachtrijen. Als je druppels uit deze wachtrijen ziet, kan je deze opdracht gebruiken om te bepalen welke wachtrijen vallen ervaren: Toon platform hardware-feed active wachtrij stats interface Gig 1/0/13
C9400#show platform hardware iomd 1/0 data-path 13 detail ----> slot 1, interface 13 lcportmap.xml: ---> Line Card (lc) ASIC instance 0 is associated with interface Gig1/0/13 id 13 asic 0 asicport 12 mac 23 contextid 12 intl_port_sup0 9 intl_port_sup1 1 maxspeed DEV_PORT_SPEED_1G asic_subport 4 fp_portmap.xml: ---> Supervisor ASIC 1, core 0 is associated with front panel (fp) interface Gig1/0/13 id 13 asic 1 core 0 port 12 mac 0 subport 4 contextid 0 maxspeed DEV_PORT_SPEED_1G gpn 113 active 1 data path:
slot 3 +--ACTIVE SUP--+ | | ---> Supervisor ASIC 1, core 0 on the slot 3 active Supervisor associated with interface Gig1/0/13 | ASIC 1 | | Core 0 | | Asic Port 12 | | | | (Mac 0) | |Nif_Rx NifTx| +--------------+ | | | | SLI MAC 9 | | +---------------+ | SLI_Tx SLI_Rx| ---> Line Card 1. The statistic output below is only for this Line card ASIC | | | ASIC 0 | | Asic Port 12 | | | | (Mac 23) | | NIF_Rx NIF_Tx| +---------------+ Front Port 1/0/13 ^ | | | | | | V ============================================== Nif MAC 23 Inforation: NifRxByteGroupStats: NifTxByteGroupStats: rxBytes 4457854 txBytes 6440428 NifRxByteDestinationGroupStats: NifTxByteDestinationGroupStats: rxUnicastBytes 1163684 txUnicastBytes 1164528 rxMulticastBytes 3294170 txMulticastBytes 5250491 rxBroadcastBytes 0 txBroadcastBytes 25409 NifRxPortStatusGroupStats: NifTxFrameDestinationGroupStats: rxUnicastFrames 18155 txUnicastFrames 18158 rxMulticastFrames 21235 txMulticastFrames 24625 rxBroadcastFrames 0 txBroadcastFrames 51 rxPauseFrames 0 txPauseFrames 0 rxCos0PauseFrames 0 txCos0PauseFrames 0 rxCos1PauseFrames 0 txCos1PauseFrames 0 rxCos2PauseFrames 0 txCos2PauseFrames 0 rxCos3PauseFrames 0 txCos3PauseFrames 0 rxCos4PauseFrames 0 txCos4PauseFrames 0 rxCos5PauseFrames 0 txCos5PauseFrames 0 rxCos6PauseFrames 0 txCos6PauseFrames 0 rxCos7PauseFrames 0 txCos7PauseFrames 0 rxOamProcessedFrames 0 txOamFrames 0 NifRxPortStatusGroupStats: NifTxPortStatusGroupStats: rxCollisionFragments 0 txLateCollisionFrames 0 rxFcsErrorFrames 0 txsystemFcsErrorFrames 0 rxInvalidOversizeFrames 0 txOversizeFrames 0 rxMacOverrunFrames 0 txMacUnderrunFrames 0 rxIpgViolationFrames 0 txDeferredFrames 0 rxOamDroppedFrames 0 txExcessiveDeferralFrames 0 rxSymbolErrorFrames 0 txOkMultipleCollisionFrames 0 rxValidOversizeFrames 0 txOkSingleCollisionFrames 0 rxValidUndersizeFrames 0 goldFramesTruncated 0 NifRxSizeGroupStats: NifTxSizeGroupStats: rx32768toMtuFrames 0 tx32768toMtuFrames 0 rx16384to32767ByteFrames 0 tx16384to32767ByteFrames 0 rx8192to16383ByteFrames 0 tx8192to16383ByteFrames 0 rx4096to8191ByteFrames 0 tx4096to8191ByteFrames 0 rx2048to4095ByteFrames 0 tx2048to4095ByteFrames 0 rx1519to2047ByteFrames 51 tx1519to2047ByteFrames 0 rx1024to1518ByteFrames 15 tx1024to1518ByteFrames 0 rx512to1023ByteFrames 17 tx512to1023ByteFrames 186 rx256to511ByteFrames 3374 tx256to511ByteFrames 9318 rx128to255ByteFrames 6505 tx128to255ByteFrames 6518 rx65to127ByteFrames 11237 tx65to127ByteFrames 8526 rx64ByteFrames 18191 tx64ByteFrames 18286 ============================================== ----------------------------------------------------> Input queue (Igr = Ingress) IgrPacketCounters: EgrPacketCounters: packetsIn 97078 packetsIn 576307 packetsOut 97078 packetsEnqueueFcd_val 0 packetsDropped 0 packetsMarkedForDrop 0 fpsSourcedPadErrorCount 0 padErrorPacketsIn 0 igrSourcedPadErrorCount 0 padErrorPacketsOut 0 ============================================== For aqmRedQueueStats for asic port 12: AqmRedQueueStats: (sum of all queues) ---> Output queue (Agm = Active queue management) acceptByteCnt0 0 acceptFrameCnt0 0 acceptByteCnt1 0 acceptFrameCnt1 0 acceptByteCnt2 6440428 acceptFrameCnt2 42834 dropByteCnt0 0 dropFrameCnt0 0 dropByteCnt1 0 dropFrameCnt1 0 dropByteCnt2 0 dropFrameCnt2 0 outOfSoftBufDropByteCnt 0 outOfSoftBufDropFrameCnt 0 maxQebDropByteCnt 0 maxQebDropFrameCnt 0 ============================================== SLI MAC 9 - SUP 0: ( an ACTIVE sup in slot 3 ) SliTxByteGroupStats: SliRxByteGroupStats: txBytes 4457854 rxBytes 6440428 SLI MAC 1 - SUP 1: SliTxByteGroupStats: SliRxByteGroupStats: txBytes 0 rxBytes 0
Controleer de stroombeheerstatus vanuit een lijnkaartperspectief voor de interface van het voorpaneel. Dit helpt elke congestie op de interface te identificeren.
- Waarden zijn "-" wanneer er geen stroomcontrole is anders wordt het nummer van de wachtrij dat stroommebeheersing ervaart (congestie) aangegeven.
- Flow control dat door de interface wordt ontvangen wordt doorgegeven van de Line Card ASIC op de Line-kaart naar de Supervisor ASIC op de supervisor ASIC waar AQM-druppels doorgaans op de Supervisor ASIC worden gezien. De OCI (Out-of-band Control Interface) is het interne communicatiekanaal tussen de lijnkaart en de actieve supervisor die wordt gebruikt om het stroombeheer van lijnkaart naar supervisor aan te geven.
C9400#show platform hardware iomd 1/0 flowcontrol status ---> slot 1
Slot 1 - number of ports 48
slot 1: Port 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
IsmF - - - - - - - - - - - - - - - - - - - - - - - -
IqmC - - - - - - - - - - - - - - - - - - - - - - - -
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
IsmF - - - - - - - - - - - - - - - - - - - - - - - -
IqmC - - - - - - - - - - - - - - - - - - - - - - - -
Controleer of het controleverkeer vanuit een ASIC-perspectief van de lijnkaartkaart tussen de lijnkaartstap ASIC op de lijnkaart en de supervisor die ASIC op de actieve en standby Supervisors via de OCI-interfaces doorstuurt.
- OCI = out-of-band regelinterface = interne communicatiekanalen tussen de lijnkaart en actieve en standby toezichthouders
C9400#show platform hardware iomd 1/0 oci status ---> slot 1 Asic 0, Mac 10, Tx OCI Config 0, OCI Merge FALSE, OCI Enabled, Link Status 0 (UP) Network Port Range 0---47, Local Port Range 0---47 NifRxByteGroupStats: rxBytes 177402572782108 NifTxByteGroupStats: txBytes 141925777717156 Asic 0, Mac 11, Tx OCI Config 0, OCI Merge FALSE, OCI Enabled, Link Status 0 (UP) Network Port Range 0---47, Local Port Range 0---47 NifRxByteGroupStats: rxBytes 963489284 NifTxByteGroupStats: txBytes 770809988
Controleer welke interfaces op de lijnkaart deel uitmaken van dezelfde poortgroep die 8 Gbps bandbreedte van de lijnkaartstub ASIC op de lijnkaart deelt naar de supervisor die ASIC op de actieve supervisor uitvoert. Elke poortgroep wordt geassocieerd met één van de SLI (System Link Interface) op de lijnkaartstap ASIC naar de supervisor.
C9400#show platform hardware iomd 1/0 portgroups ---> slot 1
Port Interface Status Interface Group Max <-- aggregate bandwidth for 8 ports
Group Bandwith Bandwidth 1 TenGigabitEthernet1/0/1 up 1G 1 TenGigabitEthernet1/0/2 down 1G 1 TenGigabitEthernet1/0/3 admindown 1G 1 TenGigabitEthernet1/0/4 down 1G 1 TenGigabitEthernet1/0/5 down 1G 8G 1 TenGigabitEthernet1/0/6 down 1G 1 TenGigabitEthernet1/0/7 down 1G 1 TenGigabitEthernet1/0/8 down 1G 2 TenGigabitEthernet1/0/9 down 1G 2 TenGigabitEthernet1/0/10 down 1G 2 TenGigabitEthernet1/0/11 down 1G 2 TenGigabitEthernet1/0/12 down 1G 2 TenGigabitEthernet1/0/13 up 1G 8G 2 TenGigabitEthernet1/0/14 down 1G 2 TenGigabitEthernet1/0/15 down 1G 2 TenGigabitEthernet1/0/16 down 1G 3 TenGigabitEthernet1/0/17 down 1G 3 TenGigabitEthernet1/0/18 down 1G 3 TenGigabitEthernet1/0/19 down 1G 3 TenGigabitEthernet1/0/20 down 1G 3 TenGigabitEthernet1/0/21 down 1G 8G 3 TenGigabitEthernet1/0/22 down 1G 3 TenGigabitEthernet1/0/23 down 1G 3 TenGigabitEthernet1/0/24 down 1G 4 TenGigabitEthernet1/0/25 down 1G 4 TenGigabitEthernet1/0/26 down 1G 4 TenGigabitEthernet1/0/27 down 1G 4 TenGigabitEthernet1/0/28 down 1G 4 TenGigabitEthernet1/0/29 down 1G 8G 4 TenGigabitEthernet1/0/30 down 1G 4 TenGigabitEthernet1/0/31 down 1G 4 TenGigabitEthernet1/0/32 down 1G 5 TenGigabitEthernet1/0/33 down 1G 5 TenGigabitEthernet1/0/34 down 1G 5 TenGigabitEthernet1/0/35 down 1G 5 TenGigabitEthernet1/0/36 down 1G 5 TenGigabitEthernet1/0/37 down 1G 8G 5 TenGigabitEthernet1/0/38 down 1G 5 TenGigabitEthernet1/0/39 down 1G 5 TenGigabitEthernet1/0/40 down 1G 6 TenGigabitEthernet1/0/41 down 1G 6 TenGigabitEthernet1/0/42 down 1G 6 TenGigabitEthernet1/0/43 down 1G 6 TenGigabitEthernet1/0/44 down 1G 6 TenGigabitEthernet1/0/45 down 1G 8G 6 TenGigabitEthernet1/0/46 down 1G 6 TenGigabitEthernet1/0/47 down 1G 6 TenGigabitEthernet1/0/48 up 1G
Revisiegeschiedenis
| Revisie | Publicatiedatum | Opmerkingen |
|---|---|---|
1.0 |
23-Jun-2022 |
Eerste vrijgave |
FeedbackContact Cisco
- Een ondersteuningscase openen
- (Vereist een Cisco-servicecontract)